ClassIII_Qtr_CCGGN

Amount

Preparation of plastered surface for oil bound distemper including sand papering the surface, applying one coat of linseed oil, and filling with approved quality filler, consisting of white lead, linseed oil, varnish and chalk miti including finishing the surface to the required finish complete (HSR item No.16.51)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work (HSR item No.16.60)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint complete in all respect (HSR item No.16.5)

Providing two coats of exterior acrylic emulsion paint of 1st quqlity complete in all respect (HSR item No.16.79)

Scrapping of cement plaster complete in all respect (HSR item No. 8.32c)

10MM thick cement plaster 1:3complete in all respect (HSR item No. 15.51)

12MM thick cement plaster 1:4complete in all respect (HSR item No. 15.5)

Chowkats of commercial hard wood such as hollock, champ, chikassy and chaplash etc., (Non-coniferous timber other than teak conforming to I.S.specification no.1003 kiln seasoned, of doors and windows including iron hold fasts, corner straps, scraws, bolts for hold fasts, etc., complete fixed in position ( HSR item No. 17.12)

Commercial hard wood such as hollock, champ, chikrassy and chaplash, etc., (non- coniferous timber other than teak conforming to I.S. specification No.1003 kiln seasoned),shutters with vertical styles and rails, as specified in the statement No.1 (attached in the end of this chapter), with two Nos. plywood panels of the specified thickness, mentioned below, tongued and grooved including the cost of iron hinges, screws, chocks/cleats, stops, etc., complete fixed in position excluding the cost of tower bolts and handles but including the labour for fixing the same complete in all respect (HSR item No.17.30a) 35mm thick

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic resin,hot- pressesd,conforming to I.S.2202 part I and II, fixed in position,including iron hinges,screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges.) complete in all respect (HSR item No.17.93a-ii) (30mm thick)

Factory manufactured panelled and glazed door shutters of commercial hard wood, such as hollock, champ, chikrassy and chaplash,etc.,(non-coniferous timber other than teak,conforming to I.S.specification No.1003, kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 12 mm thick commercial veneered both sides particle board or plywood of B.W.R. grade, hot-presses, including cost of iron hinges,screws,chocks/cleats,stops, and nails etc., complete,fixed in position (excluding the cost of any fittings,other than specified above,but including labour for fixing the same in position). complete in all respect (HSR item No.17.91b) 35mm thick)

Factory manufactured wire gauze door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash,etc.,(non-coniferous timber other teak,conforming to I.S.specification No.1003, kiln-seasoned),with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail, and wire gauze of 140G or 120G designation including cost of iron hinges, screws,chocks/cleats,stops nail etc.,complete fixed in position (excluding the cost of any fitings,other than specified above,but including labour for fixing the same in position)-(style and rails of windows shutter shall be 75 mm wide) complete in all respect (HSR item No.17.92ii) 35mm thick)

Wire gauze fixed on chowkats with 25 mm thick cover moulding of full width of commercial hard wood such as hollock, champ chikrassy and chaplash etc., (Non-coniferous timber, other than teak, conforming to I.S. specification No.1003, kiln seasoned). complete in all respect (HSR item No.17.33)

Cost of aluminium fittings complete for doors and windows, such as tower bolts,handles,etc., and screws for these fittings (excluding sliding bolt) for single leaf shutter complete in all respect (HSR item No.17.72a)

Providing and fixing sliding bolt with nuts and screws,etc. complete in all respect (HSR item No.17.83c-ii) 250mmx16mm

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge) INDIAN TYPE WATER CLOSET SUITE CONSISTING OF:- Closet set VITREOUSCHINAWARE W.C.PAN WITH horizontal inlet, for sinking into floor with A PAIR OF FOOTRESTS, 100 MM H.C.I’P’ TRAP WITH or without vent a required and suitable joint for closet inlet; 12 ½ LITRES CAPACITY mosquito proof CAST IRON FLUSHING CISTERN BEST INDIAN MAKE I.S.I MARKED NOMOS OR OTHER (as approved by the Engineer-in-charge) painted with non-yellowing white or other approved shade ENAMEL PAINT ON OUT SIDE AND BLACK BITUMASTIC SUPERIOR PAINT OF APPROVED manufacture ON INSIDE complete with all accessories such as 20 mm G.I. over flow pipe with specials & clamps upto 15 cm above floor level of W.C. room, and brass perforated mosquito proof cap, 32 mm outlet, 15 mm I.S.I. marked ballcock, G.I. pull AND chain, R.S. or C.I., painted brackets and mosquito proof couplings for outlet and overflow pipes, etc; 32 MM DIAMETER TELESCOPIC 1.25 mm thick galvanized inside and outside STEEL FLUSH PIPE with clips; Complete in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS AND PAINTING OF FITTINGS, ETC (HSR item No. 30.1a-i) water closure suite

Dismantling white or coloured glazed tiles (to be carefully removed) complete in all respect (HSR item No.8.38)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete HSR item No. 14.92b) size 300x450mm

Providing LABOUR FOR LAYING JOINTING, FIXING AND TESTING G.I./P.V.C./W.I.PIPE LINES AND SPECIALS tees bends, sockets elbows etc., INSIDE BUILDING and testing etc., complete including cutting threading complete in all respect (HSR item No. 28.18b-i) 15mm dia pipe

20mm dia pipe

Supply EXTRA FOR FIXING AND JOINTING UNION COUPLINGS IN G.I. AND W.I.PIPELINES.complete in all respect (HSR item No.28.21)

Dismantling disjointing removal and carriage of store GI Pipe .complete in all respect (HSR item No.28.48) 15mm dia pipe

20mm dia pipe

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the engineer-in-charge) (HSR item No. 30.75a) Bib cock long body).

Bib cock

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineer-in-charge)15mm stop cock concealed stop cock with flange (HSR item No.30.76a-ii &b-ii)

20mm including stop cock concealed with flange

Providing and fixing 15mm CP brass laboratory cock swan neck of best quality to the approval of the Engineer-in-Charge (HSR item No. 30.78a)

Providing and fixing helical door spring 150mm (superior quality) including necessary screws complete .(HSR item No. 17.79)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE FLEXIBLE TUBE CONNECTION. (HSR item No. 30.82b-i) size 15mmx300mm

Precast chequered tiles of 20 mm thickness in ordinary grey cement without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps and landings In case colour chequered tiles in flooring are used, increase the through rate of Item No. 14.45 by 10%.

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS.