Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹2.0 LAccepted-Finance | ₹2.0 L | L1 | Accepted-Finance Complied as per NIT |
| 2 | L2₹2.1 L+₹10,150 (5.15%)Accepted-Finance | ₹2.1 L+₹10,150 (5.15%) | L2 | Accepted-Finance Complied as per NIT |
| Sl No | Description | Qty | Unit | H SWAMY L1 | B NAGEGOWDA L2 |
|---|---|---|---|---|---|
| 1.00 | Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m.
All kinds of soil | 4 | each | 1,500 ₹6,000 | 100 ₹400 Lowest |
| 2.00 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.
All kinds of soil | 30 | sqm | 300 ₹9,000 | 35 ₹1,050 Lowest |
| 3.00 | Cement concrete flooring 1:2:4 (1 cement : 2 M sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.
40 mm thick with 20 mm nominal size stone aggregate | 25 | sqm | 500 ₹12,500 Lowest | 600 ₹15,000 |
| 4.00 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
1:4:8 (1 Cement : 4 M sand : 8 graded stone aggregate 40 mm nominal size derived from natural sources) | 2 | cum | 7,000 ₹14,000 Lowest | 7,000 ₹14,000 Lowest |
| 5.00 | 15 mm cement plaster on rough side of single or half brick wall of mix:
1:4 (1 cement: 4 M sand) | 15 | sqm | 400 ₹6,000 Lowest | 400 ₹6,000 Lowest |
| 6.00 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 5.00 in superstructure above plinth level up to floor V level in all shapes and sizes in :
Cement mortar 1:4 (1 cement : 4 M sand) | 1.5 | cum | 9,000 ₹13,500 | 7,000 ₹10,500 Lowest |
| 7.00 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including necessary bending, welding and bolted with special shaped washers etc. complete. as per direction of Engineer-in-charge.
Hot finished welded type tubes
MAKE: APL Apollo/TATA | 400 | kg | 125 ₹50,000 Lowest | 190 ₹76,000 |
| 8.00 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18
microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
MAKE: JSW/ TATA | 50 | sqm | 800 ₹40,000 Lowest | 800 ₹40,000 Lowest |
| 9.00 | Providing and fixing of Aluminium composite panel of approved make and colour for roofing at required level fixed to the MS sections. The panel should consist of 3mm thick non-halogenated FR grade mineral based polymer ( 2 hrs fire resistance as per ASTM E119-12 and clause B, S1, do as per ENT135011sandwiched between 0.50 skins thick aluminium sheet making a total panel thickness of 4mm. The surfaces will be finished with PVDF based coating on top sides and service coating on reverse sides would be in polyester paint. The panels shall be fixed using selfthreading screws / stainless-steel bolts and nuts complete with spring washer and cap nuts and all other necessary etc. complete.
Make: Aludecor/Alstrong/Viva | 12 | sqm | 3,000 ₹36,000 | 2,850 ₹34,200 Lowest |
| 10.00 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :
Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
MAKE: asian - apcolite gloss enamel OR Nerolac – synthetic enamel OR Dulux - Gloss enamel | 50 | sqm | 200 ₹10,000 Lowest | 200 ₹10,000 Lowest |
Tender Value
₹2.2 L
EMD Value
₹4,400
Closing Date
29 Jul 2026, 3:00 pmClosed
The Director, CSIR-CFTRI, Mysuru
CSIR-CFTRI, Cheluvamba Mansion, KRS Road, Mysuru
Providing and fixing GI roof structure for boiler and ACP sheet covering over the new extruder machine at CoEMIC (Unit-3), CSIR-CFTRI, Mysuru
2026_CSIR_284257_1
E/CW/003/1125/2026-27
Open Tender
Civil Works
Item Rate
60 days
CSIR-CFTRI
Please refer Tender documents.
8 documents required · 8 mandatory
₹0
₹4,400
30 Jul 2026
15 Jul 2026
30 Jul 2026
15 Jul 2026
29 Jul 2026
15 Jul 2026
15 Jul 2026 - 20 Jul 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m.
All kinds of soil | 4 | each | - | - |
| 2 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.
All kinds of soil | 30 | sqm | - | - |
| 3 | Cement concrete flooring 1:2:4 (1 cement : 2 M sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.
40 mm thick with 20 mm nominal size stone aggregate | 25 | sqm | - | - |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
1:4:8 (1 Cement : 4 M sand : 8 graded stone aggregate 40 mm nominal size derived from natural sources) | 2 | cum | - | - |
| 5 | 15 mm cement plaster on rough side of single or half brick wall of mix:
1:4 (1 cement: 4 M sand) | 15 | sqm | - | - |
| 6 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 5.00 in superstructure above plinth level up to floor V level in all shapes and sizes in :
Cement mortar 1:4 (1 cement : 4 M sand) | 1.5 | cum | - | - |
| 7 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including necessary bending, welding and bolted with special shaped washers etc. complete. as per direction of Engineer-in-charge.
Hot finished welded type tubes
MAKE: APL Apollo/TATA | 400 | kg | - | - |
| 8 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18
microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
MAKE: JSW/ TATA | 50 | sqm | - | - |
| 9 | Providing and fixing of Aluminium composite panel of approved make and colour for roofing at required level fixed to the MS sections. The panel should consist of 3mm thick non-halogenated FR grade mineral based polymer ( 2 hrs fire resistance as per ASTM E119-12 and clause B, S1, do as per ENT135011sandwiched between 0.50 skins thick aluminium sheet making a total panel thickness of 4mm. The surfaces will be finished with PVDF based coating on top sides and service coating on reverse sides would be in polyester paint. The panels shall be fixed using selfthreading screws / stainless-steel bolts and nuts complete with spring washer and cap nuts and all other necessary etc. complete.
Make: Aludecor/Alstrong/Viva | 12 | sqm | - | - |
| 10 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :
Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
MAKE: asian - apcolite gloss enamel OR Nerolac – synthetic enamel OR Dulux - Gloss enamel | 50 | sqm | - | - |
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.89 MB
TEN003CW202627.pdf
Tender Documents • 1.19 MB
BOQ_331777.xls
BOQ • 0.39 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .