Various electric work against Additional Business Plan 2023-24 for quality power supply in Aligarh City on Semi Turn-key Basis under the area EUDD-1 Aligarh

Amount

Safe carriage of following material from Store Centre, Sarsol, Aligarh to the respective site of work including the work of its loading & unloading at the repective ends and its erection as per direction of supervising engineer, including the cost of arrangement of labour, T&P carrier etc. required for proper completion of work as per RESSPO Norms:-

11 Mtrs. ST Pole

13 Mtrs. ST Pole

Earthing of Pole

Stay complete(GI Stay Rod 16x1800mm, 5 Kgs. Stay wire 7/8, Stay clamps, Insulator, Bolts, Nuts & Washers)

33 KV XLPE Cable 3x300 sq.mm.

ACSR Dog Conductor

ACSR Weasel Conductor

AB Cable 3x120+1x95+x16 sq.mm.

Distribution Transformer 250 KVA

Distribution Transformer 400 KVA

11 KV D.O. Fuse Set

11 KV TPMO

11 KV Pin Insulator with Pin

11 KV Polymer Pin Insulator with Pin

11KV Disc Insulator

11KV Disc fitting

11 KV F BRACKET

L.T. PVC Cable 1x400 mm.

L.T. XLPE Cable 3.5x240 mm.

11 KV V Type Cross Arm

GI Wire 6 swg

GI Wire 10 swg

33 KV Control Pannel (Double)

33 KV cable Jointing Kit 3x300sq.mm. (Outdoor)

Stone Pad

AL LUG 240 SQMM

AL LUG 400 SQMM

Top Channel size 125x65x2240 mm.

Dropper Channel size 100x50x2028 mm.

Tee off Chennal size 125x65x1300mm.

Base Angle size 75x75x6x2028 mm.

Pole Clamp

Danger Board with Clamp

Barbed wire

Nut Bolt & Washer

Number Plate with clamp

Gaurding Angle

I Bolt

ALUMINIUM WINDING WIRE

T/F END CLAMP 240 SQMM

T/F END CLAMP 400 SQMM

Construction of plinth at various 11/0.4 KV Sub-station suitable for distribution transformer having size 5’x 5’ x 5’ out which 2’ below the ground. Work will include digging of foundation 2’ deep & brick work with Ist class bricks having cement and sand mortar of ratio 1:6 on all the walls, each of 9” thickness. The area inside the wall shall be duly filled by mud up to the height of appropriate level from ground level and shall be duly watered & rammed. Above the filling C.C. of ration 1:6:12 (Cement sand and brick ballast) giving 4” layer shall be provided. Above C.C. layer RCC layer having 4” thickness and with ratio 1:2:4 of cement sand and stone ballast shall be provided Re-enforcement shall be provided by providing net of (8 Nos. + 8 Nos.) M.S. rods of size 10 mm dia and each of 5’ length in the middle of the top of C.C. layer. The plinth shall be plastered with 12mm thick plaster in ratio 1:4 at all sides. This work will include cost of labour, T&P and all material required for construction of plinth which shall be provided by the contractor as per RESSPO Norms.

Providing and fixing of welded wire mesh fencing around transformer plinth with M.S. Angle of size 35X35X6 mm. length and 1.20 Meters height, such panels shall be supported on M.S. Angle from of size 40X40X6 mm. having 04 Nos. corner supports of height 1.65 Meters including extended legs for grouting which will be used as a door for entry of the personnel or removal/shifting of transformer with welded hinges, sliding belt etc. for locking the arrangement as per drawing and specifications the fencing will be painted one coat of red oxide primer and then two coats of bus green synthetic enamel paint. The rates should be inclusive of all materials required for proper completion of above work (length of each fencing approx. 11 Meters)

Dismantling and removal of following material from the existing line and then stacking in the respective JE’s (Store) as per direction of Supervising Engineer. It includes the work of cartage, cost of labour, T&P carrier etc. required for proper completion of work.

Dismentling of 63KVA Distribution Transformer

Dismentling of 250KVA Distribution Transformer

P K ENTERPRISES