SPECIAL REPAIR TO TRANSIT FACILITY AT BHUBANESWAR, ODISHA

Amount

SUBHEAD-I : EARTH WORK EXCAVATION. Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 Sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

SUBHEAD-II : PLAIN REINFORCED CEMENT CONCRETE. Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering,finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.(Note:- Cement content considered in this item is @ 330 Kg/Cum. Excess/ less cement used as per design mix is payable/recoverable separately).

All works above plinth level upto floor V level

Centering & shuttering including strulting,propping etc .and removal of form for :

Suspended floors,roofs,landings,balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. Work including straightening, cutting, bending, placing in position and binding all complete upto all levels.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Chemical grouting .Providing and fixing chemical grout drilling 20mm dia holes in sheet rock upto a depth of 0.5m including labour & machinery all complete

SUB HEAD III- STONE & BRICK MASONARY. Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level

Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

In cement mortar

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured):

From brick work in cement mortar

Credit for bricks obtained from demolishing brick work

SUBHEAD-IV : PLASTERING & SURFACE TREATMENT : 12 mm cement plaster of mix:

1:6(1 cement : 6 coarse sand)

Removing dry or oil bound distemper,water proofing cement paint and the like by scrapping sand papering and preparing the surface smooth including necessary repairs to scratches etc.complete

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade

New work (Two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 Sqm over and including priming coat of exterior primer applied @ 2.20 Kg/10 Sqm)

SUBHEAD-V : FLOORING : Providing & laying vitrified floor tiles in different sizes (Thickness to be specified by the manufacturer ) with water absorption less than 0.08% & conforming to IS :15622 of approved make in all colors & shades,laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand ) jointing with grey cement slurry @ 3.3 Kg/ Sqm including grouting the joints with white cement and matching pigments etc.complete

Size of tile 600 x 600 mm

Providing & laying vitrified floor tiles in different sizes (Thickness to be specified by the manufacturer ) with water absorption less than 0.08% & conforming to IS :15622 of approved make in all colors & shades,laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand ) jointing with grey cement slurry @ 3.3 Kg/ Sqm including grouting the joints with white cement and matching pigments etc.complete

Mat finished Non skid Floor tiles 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3Kg per Sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 1st quality ceramic glazed wall tiles (300x600mm) confirming to IS15622 (thickness to be specified by manufacturer) of approved shade/colour of make such as Kajaria, Johnson, NITCO, RAK ,Bell or equivalent including cost of approximately 20 mm thick cement mortar 1:4 and necessary cement plaster, complete in all respects as directed by Engineer -In Charge.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 Kg/Sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing & fixing 18mm thick gang saw cut ,mirror polished ,premoulded and prepoblished ,machine cut for kitchen platforms ,vanity counters ,window sills,facias and similar locations of required size ,approved shade,colour & texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) ,joints treated with white cement ,mixed with matching pigment,epoxy touchups,including rubbing,curing ,moulding and polishing to edges to give high gloss finish etc.complete at all levels.

(a)Granite of any colour and shade

Area of slab over 0.50Sqm

Providing ,fitting & fixing of commerical graded laminate flooring in sizes 12mm x 196mm x 2440mm having fully textured top layer of approved colour including fixing in position, planed, levelled smooth and finished complete.

Providing edge moulding to 18 mm thick granite stone counters,vanities etc including machine polishing to edge to give high gloss finish etc .complete as per design approved by Engineer-in-charge

Granite work

Extra for grinding for Floor wherever required as per directed by Engineer -In Charge for Kota / Marble stone fixing.

Extra for grinding for Skirting as per directed by Engineer-In-charge

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50metres lead

For thickness of tiles above 25mm upto 40mm

SUBHEAD-VI : STEEL, JOINERY & WOOD WORK. Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

French sprit polishing on 35mm thick flush door shutter Two or more coats on new works including a coat of wood filler

Providing & fixing PVC rigid foam sheet 1 mm thick on exsiting door shutters (bathroom & W.C doors) using synthetic rubber based adhesive

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Credit of aluminium doors,windows and clerestory windows builtup frame sections & shutter frames.

Dismantling of cup board including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Supplying and fixing wood cupboards with 19mm thick BWR board for sides,tops,bottom /base,intermediate shelf and 9 mm thick ply on back side..The cupboard shutters will be 19mm thick block board with 1mm thick plain lamination outside & 0.7 mm th white coloured laminate for inside of the cup board. The system shall be including necessary screws and bright finished stainless steel self closing hinges, handles , door catchers ,locks etc complete hardware as per direction of Engineer-in-Charge . Face area shall be measured.

600 mm deep

Supplying and fixing wood cupboards with 19mm thick BWR board for sides,tops,bottom /base,intermediate shelf and 9 mm thick ply on back side.The cupboard shutters will be 19mm thick block board with 1mm thick high gloss premium decorative lamination outside & 0.7 mm th white coloured laminate for inside of the cup board. The system shall be including necessary screws and bright finished stainless steel self closing hinges,handles ,door catchers ,locks etc complete hardware as per direction of Engineer-in-Charge .Face area shll be taken for measurement.

600 mm deep

250 mm deep

Supplying and fixing of TV unit with 19mm thick BWR board for sides,tops,bottom /base,intermediate shelf and 9 mm thick ply on back side.The unit shutters will be 19mm thick block board with 1mm thick suade finish decorative lamination outside & 0.7 mm th white coloured laminate for inside of the cup board. The system shall be including necessary screws and bright finished stainless steel self closing hinges,handles ,door catchers ,locks etc complete hardware as per direction of Engineer-in-Charge . Face area shall be taken for measurement.

Extra for providing drawers on channels in 600mm deep cupboard

Providing and fixing 12mm thick frameless toughened glass panel of approved brand and manufacture,including providing and fixing ss channelas required including silicon sealant at joints and bottom ,etc all complete as per direction of Engineer -In charge

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing of glass etching with A1 Decor 3d Film Self Adhesive Decorative Sticker Frosted Film Sidelight Anti UV (12 x 72, Off-White-1) on entrance door as per approved design .

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 5mm tinted/reflective glass shutter of approved make (partly fixed and partly sliding) as per the drawing and design including all hardwares complete including cost of conveyance,royalities and taxes of all materials and cost of labour T&P required for the work etc. complete as per drawing design and direction of Architect /Engineer-in-charge

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

a) Providing & fixing alluminium tower bolts, ISI marked,anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade,with necessary screws etc. all complete i) 200mm, long 10 mm dia

ii)100 mm long,10 mm dia

b) Providing & fixing Aldrop 300mm long with 16mm dia rod, required colour or shade with necessary screws etc., complete

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 Kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing chromium plated brass 100 mm mortice latch and lock ISI marked with six levers and a pair of lever handles of approved quality with necessery screw etc.complete.

Providing and fixing chromium plated brass handles with necessary screws etc. complete .i) 125 mm long

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing the following hardware fittings of approved make :a)Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

i) Size 125 x 64 x 1.9 mm

ii) Size 100 x 58 x 1.9 mm

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing and fixing horizontal bamboo window blinds of approved make, design and colour for windows/ glazings, etc., with bamboo vanes of 100 mm maximum width, with head-rails, carriers, and other hardware with full movement mechanism, complete, to the entire satisfaction and approval of the Client

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required).with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered including fixing accessories such as nuts, bolts, fasteners, etc.)

SUBHEAD- VII: ROOFING , WATER PROOFING & MISCELLANEOUS Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. The job shall be inclusive of providing & fixing of accessories confirming to IS 13592. a)110 mm dia

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with I.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. a) 110 mm

Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing not less than 100 gms.

Providing & fixing false ceiling at all height including providing and fixing of frame work made of special sections,power pressed from M.S. sheets and galvanised with zinc coating of 120gms/Sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27 mm and 37mm ,at 1200mm centre to centre ,one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts ,other flange of cleat fixed to the angle hangers of 25x10x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x19x0.9 mm running at the spacing of 1200mm c/c to which the ceiling section 0.5mm thick bottom wedge of 80mm with tappered flanges of 26mm Each having lips of 10.5mm ,at 450mm c/c shall be fixed in a direction perpendicular to G.I. intermediate channel with connectig clips made out of 2.6mm dia x 230mm long G.I. wire at every junction ,including fixing perimetre channels 0.5mm thick 27mm high having flanges of 20 mm & 30mm long ,the perimetre of ceiling fixed to wall / partition with the help of rawl plugs at 450mm centre,with 25mm long dry wall screws @ 230 mm interval ,including fixing of gypsum board to ceiling

12.5mm thick tapered edge gypsum plain board conforming to IS.:2095-(part 1) :2011 (Board with BIS certfication marks)

Wall Panelling: Providing & fixing metal stud wall panelling with the following specification: a) Supporting system comprising of best locally available make 51 X 35 X 0.55 mm thick metal studs @ 600 mm c/c and 51 X 32 mm metal tracks at floor, middle, door level and ceiling level with joints staggered. The verticals should touch the ceiling with horizontal ceiling channel at slab/beam bottom. b) 9 mm BWR plywood fixed on one side with 25 mm dry wall screws for the entire height of panelling. c) 1 mm premium 3d laminate upto false ceiling level. d) All exposed wood members shall be melamine polish finish including all fittings, fixtures & hardwares required. Length X height upto false ceiling will be measured for payment.

Providing & fixing sliding-folding partition upto 1.2 m height with CNC cut design made out of 19 mm block board fixed with frame (19mm B.W.R. Ply) shall be finished with melamine polish including all fittings, fixtures & hinges & hardwares for folding the systems. Face area shall be measured for payment.

Providing , fitting & fixing of batten type partition in lift lobby made out of 19mm block board as per design.The same partition shall be finished with french & melamini polish.

Providing & fixing 10mm thick Premium Acrylic sheet in ceiling & wall fixed to GI frame work with recessed deco-lights including all fittings, fixtures & hardwares required.

Providing ,fitting & fixing of high performance imaging with smart light sheet illuminator as per design including all fittings, fixtures & required hardwares.The design shall be as per drawing approved by Engineer-In charge.

Providing ,fitting & fixing of 3D acrylic decorative mirror wall sheet of hexagonal size 12.1 x 10.5 mm as per design including all fittings, fixtures & hardwares required.

Providing ,fixing & making Beautification by installing Artistic Pattachitra works or painting of traditional Odisha culture on inside walls ,Lobby & reception entrance as per approved/directed by Engineer-In Charge.

Providing & fixing of environmentally friendly, waterproof and oil-proof Heavy-weight Vinyl wallpapers are deeply embossed using a thick vinyl material. These wall paper shall be fixed by using heavy duty adhesive on smooth wall surcface as per manufacturer's instruction. The design shall be approved by concerned architect & Engineer in-charge.

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done.

SUB HEAD -VIII:SANITARY SERVICES Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floorswherever required :W.C. pan with ISI marked white solid plastic seat and lid. Cat No-SLS-WHT-6751ZP

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing Bottle Trap (With Internal Partition) 32mm Size With 250mm Cat no- ALD-CHR-769 of Jaguar/Equivalent.

Providing ,fitting & fixing C.P brass wall mixer of Make Jaquar continental or equivalent (Jaquar Cat No.- FLR 5281N

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm of NIRALI make or equivalent.

Providing and fixing of Waste Coupling 32mm Size Full Thread With 80mm Height for sink or wash basin CAT no- ALD-CHR-705 of Jaguar /equivalent.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder : CAT No- ACN-CHR-1151N of Jaguar/Equivalent.

Providing fixing C.P. brass towel rack of size 600 mm long fixed to ss cleats with CP brass Screws complete as per instructions of the Engineer-in-charge of jaguar make cat no - AKP -35781PS/ Equivalent design & make.

Providing, fitting & fixing of Hand Shower (Health Faucet) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook-

Providing and fixing 15 mm nominal bore C.P. brass short body two way bib cock of approved quality conforming to IS : 8931 of jaguar make cat no- FLR 504/equivalent .

Providing and fixing approved type SS coat hooks with concealed type screws of approved make.Jaquar ACN-1161N or equivalent)

Supplying & Fixing C P Soap Dish of approved make complete as directed Make :- Jaquar Cat No - ACN -131 N or equivalent)

Providing and fixing Gyser of 15Ltrs Capacity .Make Jaquar Elina-prime

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass hreaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

INTERNAL ELECTRIFICATION Lights Points Supply, Installation, testing & Commissining of following Point Wiring for Light/ Fan/ exhaust fan with 2 runs of 650V grade 1.5 Sq.mm & 1 run of 1.5 Sq.mm FRLS insulated multistranded Copper wires, run in & including 25mm dia, heavy guage FR PVC conduits concealed in wall / ceiling conforming to IS 732 including all accessories such as junction boxes, conduit bends, elbows and ceiling rose, anodised GI Switch box with modular switch and the box covered with front plate.

One Light point controlled by one 6A switch.

Two Lights point controlled by one 6A switch.

Three Lights point controlled by one 6A switch.

Four Lights point controlled by one 6A switch.

One Light Point controlled by 2nos 6A 2way switches

Two Lights Point controlled by 2nos 6A 2way switches

Exhaust fan point controlled by one 6A switch.

Ceiling Fan point controlled by one 6A switch with 100W Step type Electronic regulator and Concealed MS fan hook box.

Supply and fixing of 5A, 3Pin Socket outlet with switch in Lighting switch boards. (Dependant).

Supply, Installation ,testing and wiring for 6A Socket outlet with 2runs of 2.5sq.mm FRLS insulated multistranded copper conductor wire and 1run of 1.5 sq.mm earth wire in and including heavy guage 25mm dia FR PVC conduit concealed in wall/ceiling along with required accessories, supply and fixing of 6A 5pin socket with switch in anodised GI box and front plate complete with fixing accessories etc as required. (Independent).

Supply, Installation, testing of Wiring with the following size 650V grade FRLS insulated multistranded Copper conductor wires in & including suitable size heavy guage FR PVC conduit concealed in wall / Ceiling including all accessories such as junction boxes, bends, elbows including and terminated with suitable lugs.

a) 2runs of 2.5Sq.mm wires with 1run of 1.5 Sq.mm in 25mm dia FR PVC conduit (For Lighting Circuits, 70W metalhalide & 150W flood light fixtures).

b) 4runs of 2.5Sq.mm wires with 2run of 1.5 Sq.mm in 25mm dia FR PVC conduit (For Lighting Circuits).

c) 6runs of 2.5Sq.mm wires with 3run of 1.5 Sq.mm in 25mm dia FR PVC conduit (For Lighting Circuits).

d) 4 runs of 6 Sq.mm wires with 2runs of 4 Sq.mm in 32mm dia FR PVC conduit. (for LDBs).

Light/Fan Fixtures Supply, Installation, testing and commissioning of following type LED light fixtures on wall/ Ceiling including all fixing accessories such as leads, etc complete as required. The LED Fixtures have Bipin Rotor type lamp holder,all prewired upto the terminal block. All fixtures shall be supplied with lamps.

1x18W LED Wall mounted light fixture (Philips : TMC 501P IXT-LED 22W P3241) WITH 1 no's Lamp

2x18W LED Wall mounted light fixture (Philips : TMC 501P 2XT-LED 22W P3242) WITH 2 no's Lamp

10W,6500K, Surface mounted LED down lighter (Philips : SM 200C LED16S 6500 PSU OD WH).

12W LED Surface mounted Fixture (Bajaj : BGCML 12 01 WW).

10W LED 2700K Recessed Mounted Dichroic Fixture (Philips : QBS 024 with ET150 Ballast).

15W,6500K, Ressed mounted LED down lighter (Philips : BBS 175 1XDLED - 5000 PSU WH).

LED Bulkhead fixture (Philips: WT202W LED 6S CW/NW PSU S2 PC).

Providing,fitting & fixing of deco-wall lights design wall cylin vivid .Cat No:- 3693 GULOW2,N11 ɸ076 X 120 X110 make of K-Lite, Crompton or equivalent.,

Providing ,fitting & fixing of pendent luminious of silver color.Cat No- shine midi/SHINE-3036 of make of K-Lite, Crompton or equivalent.

Providing ,fitting & fixing of pendent luminious of gold color.Cat No- shine midi/SHINE-3037 of make of K-Lite, Crompton or equivalent.

Providing ,fitting & fixing of Aluminium profile with PC Opal matte diffuser.Cat No- -3229/3198 of make of K-Lite, Crompton or equivalent.

Providing ,fitting & fixing of LED strip lighting in false ceiling, wall panelling etc as per designas per design

cove lighting

Ceiling Fans Supply, Installation,testing and commissioning of 1200 mm sweep Ceiling fan including down rod, blades with all accessories excluding regulator.

Supply and Fixing of 400 mm sweep wall mounted fan with fixing clamp and all accessories Electrical connections etc complete.

Exhaust Fans: Supply, Installation, testing and commissioning of Exhaust fans of following sweep with gravity louvres shutters including all accessories / Installation materials required.

a) 305mm Sweep, 900RPM

SUB HEAD - IX - FURNITURE Providing,fitting & fixing of King size of 1800 mmx2000mmx450mm made out of 19 mm block board conforming to IS 303 grade & laminate of approved colour & brand. The frame work shall be of box type storage as per drawings. with necessary hardware fittings.The top of bed shall be 19 mm block board . The skin of bed shall be finished with 1.0 mm thick laminate of approved colour & brand. Ready made beading of 2nd class wood shall be provided as per design. The bed head shall be 600 mm height from bed top & shall be made out of 12 mm Block board with laminate fixed in pattern as per drawing.all complete with MNF set all as directed/approved by Engineer-in-Charge.

Providing,fitting & fixing of Single bed size of 950 mmx2000mmx450mm made out of 19 mm block board conforming to IS 303 grade & laminate of approved colour & brand. The frame work shall be of box type storage as per drawings. with necessary hardware fittings.The top of bed shall be 19 mm block board . The skin of bed shall be finished with 1.0 mm thick laminate of approved colour & brand. Ready made beading of 2nd class wood shall be provided as per design. The bed head shall be 600 mm height from bed top & shall be made out of 12 mm Block board with laminate fixed in pattern as per drawing.all complete with MNF set all as directed/approved by Engineer-in-Charge.

Supplying of Sofa of approved configuration made out of teakwood frame work, seatback with 2nd class hard woord, seat cushioned with 75mm thick high density foam and extra padding with 20mm thick foam for making high density foam duly upholstred with fabric of approved shade & quality all exposed wooden surface finished with melamine polish etc all complete as directed/approed by the Engineer-in-Charge. a) Single Seater sofa

b) Two Seater sofa

c)Three Seater sofa

Supply of bed side table of sizes 450x400X400mm made out with 18 mm th. edge binder pratical board with Botide laminate.Top with 18mm thick post with one drawer ride on sliding chanel with handels etc. all complete.as directed/approed by the ENgineer-in-Charge.

Supplying, fitting & fixing of corner/center/Sidetable/Tea-poi/Peg table Display table of mentioned sizes shall be of approved design of Godrej/equvalent.

Center Table -900X525X400mm

Supply of Dressing table of sizes 900 mm width, 250 mm depth . The same shall be provided with 4mm thick mirror of 1250 mm height fixed between wooden/ply frame . The table shall be provided with drawer & openable shutter for storage. All exposed portion shall be finished with 1 mm laminate over BWR ply & polish on exposed wooden frame as per detail design etc all complete.

Supply of Dinning table for 8 persons of size 1950X900X750mm made out of teak wood frame & top shall be 19 mm BWR ply finished with solid surface .All exposed edges to have PVC edge moulding all complete as directed by the Engineer-in -charge.

Dining chairs:Supply of dinning chair of size 450 x 450 x 900 mm made out of 45 X 30mm teak wood for frame work without arm with 12mm thick BWRl ply with 50 mm thick high density foam on seat duly upholstered with fabric foam of approved shade & qualilty . Back of the chair should have teak wood strip Including malamine polish etc.all complete.

Providing,fitting & fixing of reception table of size 2000 X 450 X 1000 mm made out of 19mm B.W.R ply finished with PVC laminate .the design shall be followed by attached drawings.the table shall be provided with led chain light as per design

Providing,fitting & fixing of reception Cub board size 2000 X 450 X 1000 mm made out of 19mm B.W.R ply finished with PVC laminate .the design shall be followed by attached drawings.the table shall be provided with led chain light as per design

KASHI KANCHAN PVT. LTD.