Balance Work for Construction of NGO Mess in Police Line at Reckong Peo in District Kinnaur (H.P) (SH- Building portion, WS and SI works

Amount

Excavation in foundation and trenches in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the engineer-in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor) as per satisfaction of Engineer-in-charge through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour (if required). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used/ removed as per the direction of Engineer-in-charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges.

Providing form work with steel plates 3.15mm. (Three point fifteen milimetre) thick welded with angle iron in frame 30X30mmx5mm.(Thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden/ steel battens and ballies, height of propping and centring below supporting floor to ceiling any floor/height and removal of the same for in situ-reinforced concrete and plain concrete work as per the direction of Engineer-in- charge, including carriage of materials with in all leads and lifts through all modes of transportation.

Foundation, footings bases of columns etc. and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floors etc.upto any thickness in Super-structure for all floor level in all heights.

Columns, pillars, posts and struts. Square, rectangular or polygonal in plan, in Super-structure for all floor level in all heights.

Stair cases with sloping or stepped soffits excluding landings in Super-structure for all floor level in all heights.

Beams, cantilevers, girders and lintels sides and soffits of beams, beam hunchings, cantilevers, bressumers and lintels up to any depth in Super- structure for all floor level in all heights.

Edges of slabs and breaks in floors and walls up to any width in Super-structure for all floor level in all heights.

Providing and laying cement concrete 1:4:8 (One cement : four sand : eight crushed stone aggregate 40mm (Forty millimeter) nominal size) mechanically mix by concrete mixer and compacting with vibrator and curing complete excluding cost of form work in Foundation and plinth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:6:12 (One cement : six sand : twelve graded/crushed stone aggregate 40 mm (Forty millimeter) nominal size) mechanically mix by concrete mixer and curing complete including cost of centering and shuttering in Foundation and plinth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:2:4 (One cement : Two sand : four crushed stone aggregate 20mm (Twenty millimeter) nominal size) mechanically mixed by concrete mixer and compacting with vibrator and curing complete including form work in : Moulding as in cornices, window sills in Super structure in all floor in all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying damp proof course 38mm (Thirty eight millimeter) thick with cement concrete 1:2:4 (One cement: two sand: four crushed stone aggregate 12.5mm (Twelve point five millimeter) nominal size) mechanically mix by concrete mixer and curing complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Applying a coat of hot bitumen (mexphalt 80/100 or equivalent) using 1.70 kg. (One point seventy kilogram) per square metre on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerosene oil, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying reinforced cement concrete 1:1.5:3 (One cement : one point five sand : three crushed stone aggregate 20mm. (Twenty millimeter) nominal size) mechanically mix by concrete mixer and compacting the concrete with vibrator and curing complete excluding cost of form work and reinforcement for R.C.C. work in foundation and plinth in Super-structure for all floor in all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Foundation footings bases of columns, vertical surfaces and the like and mass concrete.

Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers in Super-structure for all floor in all heights.

Column, pillars, posts and struts in Super-structure for all floor in all heights.

Stair cases (except spiral stair case) excluding landing but including preparing of the surface and finishing of nosing in Super-structure for all floor in all heights.

Lintels, beams girders bressumers and cantilevers in Super-structure for all floors in all heights.

Providing Tor steel reinforcement for R.C.C. work including cutting, bending, binding and placing in position complete in Super-structure for all floor in all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Rat trap bond Brick masonary using common burnt clay building bricks) in Cement Mortar 1:4 (One cement : four sand) Second Class Bricks in Super-structure for all floor level in all heights, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Rat trap bond Brick masonary using common burnt clay building bricks) in Cement Mortar 1:6 (One cement : six sand) Second Class Bricks in Super-structure for all floor level in all heights, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Brick masonary using common burnt clay building bricks) in Cement Mortar 1:6 (One cement : six sand) Second Class Bricks upto plinth level, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Brick masonary using common burnt clay building bricks) in Cement Mortar 1:6 (One cement : six sand) First Class Bricks above plinth level in super-structure for all floors in all heights, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Half brick masonry in common burnt clay building bricks in Cement Mortar 1:4 (One cement : four sand) Second Class Bricks in super-structure for all floors in all heights, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Half brick masonry in common burnt clay building bricks in Cement Mortar 1:4 (One cement : four sand) Second Class Bricks in super-structure for all floors in all heights, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying stone soling under floors, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Marble work (table rubbed and polished for walls lining) Veneer work 2.50cm. thick in cement mortar 1:3 (one cement:three sand) including pointing with white cement mortar 1:2 (one white cement: two marble dust) with an admixture of pigment to match the marble shade Baroda Green Marble. including curing complete and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing woodwork in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position. Second class Deodar wood for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing wood work in frames of false ceiling partitions etc. sawn and put-up in position 1st class Chil wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including black enameled iron butt hinges with necessary screws 40mm.(forty millimeters) thick, 2nd class deodar wood for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Supplying and fixing glass panes with putty and nails 3mm (Three millimeter) thick, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing wooden plank ceiling with tongued and grooved jointing and wood screws (frame work and cover fillets to be measured and paid for separate) First Class Rai wood. 25mm (Twenty five millimeter) thick, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G. with wire of dia 0.56 mm (Zero point fifty six millimeter) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws. 40 mm (Forty millimeter) thick. 2nd class deodar wood for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing 40x3 mm (Forty into three millimeter) flat iron hold fast 40cm. (Forty centimeter) Long including fixing to frame with 10mm (Ten millimeter) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. (Thirty into ten into fifteen centimeter) 1:3:6 (One cement : three sand: six crushed stone aggregate 20mm (Twenty millimeter) nominal size) for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing anodized aluminum sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete for all floors. 300×16mm (Three hundred fifty into sixteen millimeter), including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

300×10mm (Three hundred into ten millimeter)

200×10mm (Two hundred into ten millimeter)

150×10mm (One hundred fifty into ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

125mm. (One hundred twenty five millimeter)

100mm. (One hundred millimeter)

75mm. (Seventy five millimeter)

Providing and Fixing 12 mm (Twelve millimeter) thick prelaminated board ISI marked No. IS12823 both side bwp phenol bonded exterior/interior grade panalled shutters with frame of second class deodar wood for doors including bright finished/black enameled iron butt hinges with necessary screws 40 mm (Forty millimeter) (For thick frame or its equivalent, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing bright finished brass handles with screws etc. complete. 75 mm. (Seventy five millimeter) in all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing oxidized M.S. hooks and eyes. 100 mm (One hundred millimeter) in all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing 19mm (Nineteen millimeter) thick water proof termite resistant commercial board in shutters for cup board fixing nickel plated piano hinges with butt joints & fixing with nails & screws back side of cup board shall be of 6.8mm (Six point eight millimeter) thick water proof ply etc. complete in all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 19mm (Nineteen millimeter) thick water proof commercial board in Shelves/Box for cupboard with butt joints & fixing with nails & screws etc. complete in wood in super structure above plinth for all floors levels , including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 1.00mm (One millimeter) thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing square edges cover fillets (beading) 19mm×6mm (Nineteen millimeter into six millimeter) section including mitring at junctions with wood screws and nails complete. 1st class Indian teak wood in all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per HPPWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 4mm (Four millimeter) thick water proof kit ply of standard quality ISI mark and approved shade and colour in wall linning including mitring at junctions, butt jointing and nails complete (Frame work for base to be measured & paid for separately) including carriage of materials through all modes of transportation with in all leads and lifts, as per HPPWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing standard quality hard board sheet lining with butt jointing and nails (Frame work and cover fillets to be measured and paid for separately) 8mm (Eight millimeter) thick, including carriage of materials through all modes of transportation with in all leads and lifts, as per HPPWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing plain lining with tongued and grooved jointing and screws (Frame work and cover fillets to be measured and paid for separately) with 1st class Rai wood. 12mm (Twelve millimeter) thick, including carriage of materials through all modes of transportation with in all leads and lifts, as per HPPWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing square edges cover fillets (beading) 50mm × 25mm (Fifty millimeter into twenty five millimeter) section including mitring at junctions with wood screws and nails complete. 1st class Indian Teak wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per HPPWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing square edges cover fillets (beading) 75mm × 37.5mm (Seventy five millimeter into thirty seven point five millimeter) section including mitring at junctions with wood screws and nails complete, 1st class class Indian teak wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per HPPWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing particle board lining with butt jointing and nails (frame work and cover fillets to be measured and paid separately) 19 mm (Nineteen millimeter) thick in super structure for all floor in all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying spartic ceremic tiles 5.5mm. (Five point five millimeter) thick in flooring (300 x 300mm. size) (Three hundred into three hundred millimeter) treads of steps laid on a bed of 12mm. (Twelve millimeter) thick cement mortar 1:3 (One cement: three sand) finished with flush pointing in white cement 1st quality ceramic tiles matt finish Somany/ Orient or its equivalent for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying 2mm (Two millimeter) thick PVC/rubber tiles flooring plain, coloured. corbed or mosaic or mattled finish, laid with approved adhesive on sub floor damp proofing treatment (to be measured separately) for payment, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying red sand stone slab in treads and risers of steps on a bed of 20mm (Twenty millimeter) thick cement mortar 1:4 (One cement : four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including preparing of nosing including rubbing and granite polish finish complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying granite stone in treads and risers of steps on a bed of 20mm (Twenty millimeter) thick cement mortar 1:4 (One cement : four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including preparing of nosing including rubbing and granite polish finish complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying HDF flooring with approved adhesive, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 75mm × 75mm (Seventy five millimeter into seventy five millimeter) rounded hand rails in straight length complete in 1st class Indian Teak wood, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 15cm wide 45cm overall semicircular plain G.I. sheet gutter with iron brackets 40×3mm (forty into three milimeter) size bolts and nuts and washers etc. including making necessary connections with drain water pipe complete as per design 0.80mm (zero point eighty milimeter) thick sheet, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 0.60mm (Zero point sixty millimeter) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimeter) diametre with prepainted limpet and rubber washers complete with all accesoriees as required, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing ridges or hips 60 cm (Sixty centimeter) overall with 0.60mm (Zero point sixty millimeter) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm (Six millimeter) dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing flushing 38cm (Thirty eight centimeter) overall with 0.60mm (Zero point sixty millimeter) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating + back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (Six millimeter) dia meter & prepainted G.I. limpet & bitumen washers complete with all accessories as required, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm (Four point five kilogram/ Square meter including filling the joints with approved adhesive complete .100mm dia (One hundred diameter) pipes, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.S. BP Sheet 2mm (Two millimeter) thick in eaves board/facia/soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured & paid separately) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing polycarbonated transparent sheet 1.20mm (One point twenty millimeter) thick in roofing with galvanized J or L hooks bolts and nuts with G.I. Limpet and bitumen rubber washer with all accessories as required, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Steel work welded in built up sections,trusses and framed work, including cutting, hoisting , fixing in position and applying a priming coat of red lead paint, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

In trusses and trussed purlins in buildings.

In gratings framed guard bars, ladders, ailing, brackets and similar works, including carriage of materials with in all leads and lifts.

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete in Super-structure for all floors. With ready mixed priming paint brushing red lead, Red-oxide/zinc oxide chrome, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enemel paint brushing to give an even shade including cleaning the surface of all dirt , dust and other foreign matters with enamel paint other than white in Super-structure for all floor, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting complete ready mixed paint brushing wood primer pink in Super-structure for all floor, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning of dirt, dust and other foreign matter, sand preparing and stopping in Super-structure for all floor. With enamel paint other than white in Super structure for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final finish to the surface complete in super structure for all floors in all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete in Super-structure for all floors, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

6mm (Six millimeters) cement plaster to ceiling 1:3 (one cement :three sand) in Super-structure for all floors, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15mm (Fifteen milimeter) cement plaster in single coat on rough side of brick/concrete /stone walls for interior/exterior plastering including arrises, internal rounded angles, chamfers and /or rounded angles not exceeding 80mm (Eighty milimeter) in girth and finished even and smooth in cement mortar 1:6 (one sand: six sand)in Super-structure for all floors in all heights, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15mm (Fifteen milimeter) cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastering including arrises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (Eighty milimeter) in girth and finished even and smooth in cement mortar 1:6 (one cement: six sand) in Super-structure for all floors in all heights, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing deoli green slates 12mm (Twelve millimeter) cladding on exterior side with 12mm (Twelve millimeter) thick cement plaster 1:3 (One cement : three sand) and jointed with cement slurry including scaffolding etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Distempering ( two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give and even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth .Priming coat with distemper primer, in Super-structure for all floors in all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Distempering ( two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give and even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth .Priming coat with distemper primer, in Super-structure for all floors in all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing plinth protection 50mm(fifty millimetres) thick in cement concrete 1:3:6 (one cement:three sand: six graded/crushed stone aggregate 20mm.(twenty millimetres) nominal size) including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing under layer for plinth protection of 75mm (Seventy Five milimeter) thick (unconsolidated) bed dry bricks/stone aggregate 40mm (Forty milimeter) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing screen with main frame of size 50 × 50mm (Fifty into fifty millimeter) hollow square section and distribution members of 25 × 25mm (Twenty five into twenty five millimeter) Mild Steel hollow square complete in all respect as per drawings, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing Mild Steel hollow pipe 10mm (Ten millimeter) dia, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying 23cm dia half round stone ware pipe in cement concrete 1:6 complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying in trenches galvanised mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid for separately) 20mm.(Twenty millimeters) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing vitreous China wash down, water closet (European type w.c.pan) with integral ‘p’ or ‘s’ trap including jointing the trap with soil pipe in cement mortar 1:1 (One cement : one sand) (seat and over to be measured and paid for separately):-Anglo Indian Universal closet. Seat No. 20012, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 100 mm (One hundred millimeter) size 'P' or 'S' trap for water closet ( squatting pan)including jointing the trap with the pan vitreous china, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing plastic seat(solid/hollow type) and cover for wash down water closet with C.P. brass hinges and rubber buffers:-Solid type (a) white plastic seat and cover, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing vitreous china wash basin No. 10001 of Hindware or its equivalent with single hole for pillar tap with C.I or M.S brackets painted white including cutting holes and making good the same but excluding fitting, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

(a) Flat back (i) 550mm × 400 mm (Five hundred fifty millimeter into four hundred millimeter)

Providing and fixing vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing rubber plug for sink/ wash basin:- 32mm dia (Thirty Two millimeter diameter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass waste for wash basin or sink:- (a) 32mm dia (Thirty Two millimeter diameter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing M.I. union for wash basin or sink 32mm dia (Thirty Two millimeter diameter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass S. Trap for wash basin and sink:- 32mm dia (Thirty Two millimeter diameter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 100mm (One hundred millimeter) sand cast iron grating for gully, floor or Nahni trap, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 600mmX450mm (Six Hundred into Four Hundred Fifty millimeter) bevelled edge mirror of superior glass mounted on 6mm (Six millimeter) thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws:- 750mmx20mm (Seven Hundred Fifty x twenty millimeter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 600x120mm (six hundred into one hundred twenty millimeter) glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. brass screws, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing toilet paper holder C.P. Brass, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P brass bib tap with capstan head ISI marked Nos. I.S. 8931 & 8934 with capstan head :- 15mm (Fifteen millimeter) dia, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing (i) C.P Brass pillar tap with capstan head :- 15mm (Fifteen millimeter) diameter, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C. P. brass stop cock:- 15mm (Fifteen millimeter diameter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass angle valve 15mm (Fifteen millimeter) without Nuts and pipe, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 15mm (fifteen millimeter) mixture for wash basin for sink, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing P.V.C. connection with brass unions:- (a) 300/450mm (Three hundred/four hundred fifty millimeter) length:- (i) 15mm (Fifteen millimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing brass full way valve with wheel 20mm (Twenty millimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing aluminum polythene(PE-AL-PE)composite pressure pipe U.V. stabilized with carbon black conforming to IS-15450-2004 for water supply including clamps at one metre spacing, cutting, fixing and making good the walls etc. but excluding the cost of fittings (internal work) pipes exposed on wall. Internal work-Exposed on wall. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

1620 (20mm (Twenty millimeter) O.D. Pipe)

1216 (16mm (Sixteen millimeter) O.D. pipe)

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm (Fifteen millimeter) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level :- 2000 (Two thousand) litres net capacity tank, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PVC floor trap ISI marked self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete.110mm×75mm. (One hundred ten millimeter into seventy five millimeter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing high pressure spigot and socket waste and ventilating pipes (ISI marked including fixing with approved adhesive etc. complete) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

75mm (Seventy five millimeter) diameter

110mm (One hundred ten millimeter) diameter

150mm (One hundred fifty millimeter) diameter

Providing and fixing single equal branch with oval access door, ISI marked PVC/ iron spun fittings and accessories insertion rubber washer 3mm.(Three millimeter) thick, bolts and nuts complete including fixed with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

150mm (One hundred fifty millimeter) diameter

110mm (One hundred ten millimeter) diameter

75mm. (Seventy five) millimeters) diameter

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3mm (Three millimeter) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

150mm (One hundred fifty millimeter) diameter

110mm (One hundred ten millimeter) diameter

75mm. (Seventy five) millimeters) diameter

Providing and fixing P.V.C. collar ISI marked including fixing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

150mm (One hundred fifty millimeter) diameter

110mm (One hundred ten millimeter) diameter

75mm. (Seventy five) millimeters) diameter

Providing and fixing P.V.C. plain bend ISI marked including fixing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

150mm (One hundred fifty millimeter) diameter

110mm (One hundred ten millimeter) diameter

75mm. (Seventy five) millimeters) diameter

Providing and fixing PVC reducer ISI marked including jointing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

150mm × 110mm (One hundred fifty millimeter into one hundred ten millimeter) diameter

110mm × 75mm (One hundred ten into seventy five millimeter) diameter

Providing and fixing stainless steel kitchen 610 × 510 mm (Six hundred ten into five hundred ten millimeter) with bowl depth 200mm (Two hundred millimeter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT Coloured/ White automatic flushing cistern with a pair of PVC/ C.I. or M.S. bracket complete with fittings including PVC symphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same (over flow pipe to be measured and paid for separately). 10 (Ten) litres net capacity.roviding and fixing P.V.C. Cistern 10 (Ten) litres capacity complete in all respect, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT ball valve of approved quality and colour 15mm (Fifteen millimeter) nominal bore, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PTMT Jet spray of approved quality and colour with one metre tube, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Bottle Trap for wash basin and sink. 32mm dia (Thirty Two millimeter diameter) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Constructing manhole with RCC top slab in 1:2:4 mix (One cement: two sand: four crushed stone aggregate 20mm (Twenty millimeter nominal size) foundation concrete 1:4:8 (one cement: four sand: eight crushed stone aggregate 40mm (forty millimeter) nominal size, inside plastering 15mm (Fifteen millimeter) thick with cement mortar 1:3 (One cement: Three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (One cement: Two sand: four crushed/graded stone aggregate 20mm (Twenty millimeter) nominal size, finished smooth complete: -

In side size 800mmX 800X500mm (Eight Hundred into Eight hundred into Five hundred millimeter) deep including C.I cover with frame. (Light duty single seal pattern-1) 455mmX 610mm (Four Hundred Fifty Five x Six Hundred Ten millimeter) internal dimensions total weight of cover and frame to be not less than 38Kg. (thirty eight Kilogram) (Weight of cover 23Kg. (Twenty Three kilogram) and weight of frame 15Kg. (Fifteen Kilogram.) a) With 200mm (Two Hundred millimeter) thick walls of Brick masonry (Second class) using common burnt clay building bricks in cement mortar 1:3 (One cement: three sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Kalap Engineers & Builders

Man mohan thakur