CONSTRUCTION OF PROTECTION WORKS AT HEAD WORKS ARIZAL INCLUDING TOILET BLOCK, SEPTIC TANK, SOAKAGE PIT AT 10MGD WATER TREATMENT PLANT AND 3.33MG SR OF WATER SUPPLY SCHEME SUKHNAG (UNDER UT CAPEX)

Amount

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed.: All kinds of soil :

Providing and laying of dry stone soling in foundation/trenches hand packed and consolidated by hand ramming. (Subject to actual quantities during execution). This item also includes all types of carriages upto site of work.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: i. 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

ii. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : i. Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class kail wood

Providing and fixing of 35mm thcik glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class Kail wood

Providing and fixing of 35mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : Second class Kail wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Second Class kail wood

Centering and shuttering including strutting, propping etc. and removal of form for: i. Foundations, footings, bases of columns etc. for mass concrete

ii. Suspended floors, roofs, landings, balconies and access platforms.

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level i. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with. i. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. i. Thermo-Mechanically Treated bars of grade Fe-500D or more

12mm Cement plaster of mix: i. 1 : 6 ( 1 cement : 6 fine sand)

15mm Cement plaster on the rough side of single or half brick wall of mix: i. 1 : 6 ( 1 cement : 6 coarse sand)

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded.

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : i. Ridges plain (500 - 600mm)

Providing and fixing plained eaves boarding. i. 2nd class kail wood. a. 300x40 mm (nominal size)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. i. In colour such as White, Ivory, Grey, Fume Red Brown

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (2 mm thick).

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: i. Two or more coats applied @ 1.25 liter/10sqm over and including one coat of special primer applied @ 0.75liter /10sqm

ii. Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. i. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid , 10 liter low level white vitreous china flushing cistern and CP flush bend with fittings and C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: i. W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : i. White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete

Providing, laying, commissioning and testing of single socketed PVC SWR Pipes (IS:13592), type B Sanitary pipes of standard make ISI marked and all fittings including jointing, door bends etc. complete. i. 160mm dia

ii. 110mm dia

Providing and fixing CP (Brass) towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour: i. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing CP (Brass) Bottle Trap for Wash basin and sink: i. Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing and fixing CP (Brass) liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.: i. Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall: a. 15 mm dia. nominal bore

Providing and fixing head shower of ISI marked Juguar, Parko or equivalent make.

Providing and fixing high flow bath hand shower and shower mixer of ISI marked Jaugar, Parko or equivalent make.

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing and fixing of CP health faucet. Toilet Seat Jet for European type water closet complete.

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : i. 150x10 mm

ii. 100x10 mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete i. 125 mm

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. i. 50 mm thick with 20mm nominal size stone aggregate

Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarsesand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : i. Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : a. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing in position electric geysers /water heaters of Havells, Racold or equivalent make with 50Ltrs. Capacity for bathroom with PVC connection pipes including all lifts and carriages upto site of work. Complete Job.

Supplying and filling in plinth with 2nd class coarse sand under floors including, watering, ramming, consolidating and dressing complete.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.

Providing and fixing CP (Brass) Ball cock of approved quality, colour and make complete with epoxy coated aluminium rod with L.P/H.P.H.D plastic balls. i. 15mm nominal bore, 105mm long, weighing not less than 138gms.

Providing and fitting of PVC conduit 25mm for electric wire including providing of junction boxes including cutting chases in walls and making good again. i. Conduit

ii. J. Box

Providing and fixing of lighting / fan / exhaust fan point wiring with 1.5Sqmm PVC insulated Copper wire of (Havells / Polycab or Equivalent) through PVC conduit pipe including providing and fixing of 6Amp Switch / 6Amp 5 pin Socket and 10 Watt LED light of reputed make recessed in wall with necessary covers of modular type duly tested and commissioned. Complete Job.

Providing and fixing of Heating point wiring with 4.0Sqmm PVC insulated Copper wire of (Havells / Polycab or Equivalent) through PVC conduit pipe including providing and fixing of 16Amp Switch / 16Amp 5 pin Socket of reputed make recessed in wall with necessary covers of modular type duly tested and commissioned. Complete Job.

Providing and fixing of 6 way SPN Distribution Board (MCB Distribution Box) ISI marked of reputed make recessed in wall with necessary covers of modular type duly tested and commissioned. Complete Job.

Providing and fixing of 4 way SPN Distribution Board (MCB Distribution Box) ISI marked of reputed make recessed in wall with necessary covers of modular type duly tested and commissioned. Complete Job.

Providing and fixing of 63 Amp MCB DP ISI marked of reputed make like Havells / Schneider duly tested and commissioned.

Providing and fixing of 16 Amp MCB DP ISI marked of reputed make like Havells / Schneider duly tested and commissioned.

Providing and fixing of 06 Sqmm PVC insulated Copper wire single core flexible cable for service line including earthing duly tested and commissioned.

Providing and fixing of 100 watt exterior LED flood lights ISI marked of reputed make like Philips, Syska etc. with IP66 water proof of rating including wires for connections duly tested and commissioned.

Providing and fixing of 1400VA hybrid pure sine wave double battery inverter with 2 No. 150AH Tall Tubular Solar type batteries, 330 Watt Solar Panels, PCU inverters, charging controllers and all connections of Solar Panels both Input & Output to make them fully functional duly tested and commissioned. It includes all installation charges and carriages upto site of work. Complete Job.

Providing and fixing of 900VA hybrid pure sine wave double battery inverter with 1 No. 150AH Tall Tubular Solar type batteries, 330 Watt Solar Panels, PCU inverters, charging controllers and all connections of Solar Panels both Input & Output to make them fully functional duly tested and commissioned. It includes all installation charges and carriages upto site of work. Complete Job.

Providing and fixing of size 200mm exhaust fan with motorized shutter ISI marked of reputed make like Havells, Usha etc. dully tested and commissioned.

Carriage of material from different sources to actual site of work by mechanical transport. i. Stones, Soling and Screening for an avg. lead of 20Kms.

ii. Sand and aggregate 20mm nominal size for an avg. lead of 20Kms.

iii. Stone aggregate 40mm nominal size for an avg. lead of 20KMs.

iv. Cement and Steel for an avg. leadoff 30Kms.

v. Bricks for an avg. lead of 15Kms.