SPECIAL REPAIR TO BLDG NO MES 56 57 58 59 60 61 62 63 64 AND 65 OF EASTERN COMMAND HOLIDAY HOME UNDER GE SHILLONG

Amount

Dismantling of plain/corrugated steel sheeting of any gauge, thickness in roof covering complete all as specified and directed.

Dismantling of timber scantling 40 sqcm and over in section in any position (unframed work).

Dismantling of wrought Iron or mild steel work of any description not otherwise described complete all as specified and directed.

Dismantling of boarding of any description fixed in any position with nails complete all as specified and directed

Dismantling wall and ceiling boards of any description including cover fillets complete.

Dismantling of floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified

Demolition of cement concrete (unreinforced) in ground floor and paving not exceeding 15cm thickness (below/above ground level) complete all as directed.

Demolition of PCC work as in block walling of any description and in any position not other wise described complete all as directed

Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exceeding 1.5 sqm each complete all as specified.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exceeding 1.5 sqm but not exceeding 4 sqm each all as specified.

M&L for vitrified ceramic tiles light shade, 9/10 mm thick(square /rectangular), double charged, premium quality, polished, area of each tile area of each tiles exceeding 0.18 sqm but not exceeding 0.36 sqm in floor etc, laid over and including 15 mm thick screed bed in CM 1:4 ,set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified.

M&L for Vitrified Ceramic tiles Double charged, premium quality 10 mm thick (square/ rectangular) polished, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, on vertical surfaces over and including 10mm thick rendering in CM1:4, complete all as specified.

M&L for 20mm thick polished granite machine cut over and including 15mm thick screed bed in CM 1:4 , bedded, jointed and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting, moulding and polishing etc complete all as specified.

M&L for Non Skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the tile colour over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed

M&L for Glazed ceramic colour tiles in vertical surface area exceeding 0.11 sqm but not exceeding 0.18 sqm and 7 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match with the tile colour over and including 10mm thick backing coat in CM 1:4 complete as specified and directed

Taking down Shutters of any description of size exceeding 1 sqm and not exceeding 2 sqm each complete and refixing in the same opening after easing and adjustment and also refixing for hardware as required all as specified and directed

M&L pre cast PCC (1:3:6) type C1 (using 20mm graded stone aggregate) solid block masonry exceeding 10cm in width or girth and setting in CM (1:6) complete all as specified and directed.

Taking down cement plaster from old surfaces of wall & ceilings including raking out joints hacking for key and scrubbing down with water complete

M&L for Rendering 15mm thick plaster in two layers (05mm thick with WPC, over 10 mm) on fair faces of concrete surface of wall in CM (1:4) finished even and smooth without using extra cement complete all as specified and directed NOTE: WPC shall be measured and paid seperatly)

M&L for 10mm rendering in cement mortar (1:6) on fare faces of brick/concrete surfaces finished the surface even and smooth without using extra cement.

M & L for preparation of new plastered surfaces of walls including cornices, pilasters etc and applying two coats of exterior acrylic emulsion coat over a coat of primer complete all as specified and directed.

M & L for preparation for newly plastered surfaces and applying two coats of distemper over a coat of primer complete all as specified and directed.

Material and labour for 12mm thick seamless calcium silicate POP finished ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having Phillips head with under head cutter at 200 mm centre to centre, including finishing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish complete including two coats of oil bound distemper complete all as specified and directed. Note: Frame work for ceiling shall be measured and paid separately under respective item.

M & L for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre, intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners including suspenders, with and including ceiling section of 0.55 mm thickness having knurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre and fix complete all as specified in SSR Part-I and as directed.

S&F pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as in roof covering including fixing with self driving machine made screws with washers and fittings of same manufacture of approved profile, shape and colour complete all as specified and directed

S&F pre-painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick as in roof covering 0.50mm thick including fixing with self driving machine made screws with washers and fitting of same manufacture of approved profile, shape and colour complete all as specified and directed

S&F 2mm thick Fibre glass reinforced translucent corrugated sheeting of profile as approved by GE with appropriate side lap as per manufacturers recommendations fixed with coach screw and washer in roof, wall etc complete all as specified and directed

S&F 2nd class HW boarding 20mm thick fixed with nails in eaves board planed one side with butt joint complete all as directed.

S&F 2nd class HW in scantling clean sawn timber fixed with nails complete all as specified and directed.

Taking up or down steel tubing and connections of 15mm bore complete all as specified and as directed.

Taking up or down steel tubing and connections of 20mm bore complete all as specified and as directed.

S&F Tubing medium grade 15mm bore laid in trenches or on walls complete including cuttings chases in walls and making good, complete all as specified and directed.

Fixing only old GI tubing medium grade 15mm bore including new fittings laid in trenches or on walls complete including cuttings chases in walls and making good, complete all as specified and directed.

S&F GI Tubing medium grade 20mm bore laid in trenches and as wall `complete including cuttings chases in walls and making good, cutting portion all as specified and directed.

Fixing only old GI tubing medium grade 20mm bore including new fittings laid in trenches or on walls complete including cuttings chases in walls and making good, complete all as specified and directed.

M & L for PCC (1:2:4) type B1 (20 mm graded stone aggregates) as in roof kerbs, padding in roof slab or mud stops, rounded or chamfered on edges complete all as specified and as directed.

M&L for 10mm rendering on roof top/padding in cement mortar (1:3) finished the surface fare without using extra cement and mixed with WPC @ 3% by weight of cement NOTE: WPC shall be measured and paid seperatly)

Supply only Integral water proofing compound

M&L for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm over one coat of cold bituminous primer conforming to [email protected] litre per square metre on the cleaned plastered surfaces including cleaning surfaces etc complete all as specified and directed

M & L for APP based polymeric water proofing membrane minimum weighing minimum 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by forced application @ 0.25kg/sqm by torch application. The overlap shall not to be less than 100mm on transverse direction and 75mm on longitudinal direction and sealing overlaps complete all as specified

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for openable door double leaf with extruded built up standard sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, without sash bars, including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required and standard aluminium fittings like handles, bolts, stays, closing mechanisms and other required fittings etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing /panelling, C.P.brass / stainless steel screws, all complete as per the directions of Engineer-in-charge. (Notes:- 1. The weight shall be of all aluminium components and fittings except the gaskets. 2. Glazing, stainless steel wire mesh and panelling to be paid for separately and all other fittings shall be deemed to be included in the rate quoted.)

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for frames of doors/windows/ventilators and partitions with extruded built up standard sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, including making provision for fixing of fittings wherever required including the cost of other required fittings etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, C.P.brass/stainless steel screws, all complete as per the directions of Engineer-in-charge. (Notes:- 1. The weight shall be of all aluminium components and fittings except the gaskets. 2. Glazing, wire mesh and panelling to be paid for separately and all other fittings shall be deemed to be included in the rate quoted.)

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for windows(sliding type) and ventilator shutters with extruded built up standard sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, including providing and fixing hinges/pivots/sliding track and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required and standard aluminium fittings like handles, bolts, stays, closing mechanisms and other required fittings etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing /panelling, C.P.brass / stainless steel screws, all complete as per the directions of Engineer-in-charge. (Notes:- 1. The weight shall be of all aluminium components and fittings except the gaskets. 2. Glazing, wire mesh and panelling to be paid for separately and all other fittings shall be deemed to be included in the rate quoted.)

M & L for 5.5 mm thick plain sheet glass, ordinary quality area not exceeding 0.5sqm in each pane complete all as specified

M & L for 5.5 mm thick obscured or frosted sheet glass, ordinary quality in square n exceeding 0.5sqm in each pane complete all as specified

M & L for 4.0 mm thick plain sheet glass, ordinary quality in square n exceeding 0.5sqm in each pane complete all as specified

M & L for 4.0 mm thick obscured or frosted sheet glass, ordinary quality area not exceeding 0.5sqm in each pane complete all as specified

M & L for stainless steel wire mesh, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified

M & L for Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover , governing pivot made of brass, other parts made of mild steel heavy duty and fixed in floor complete all as specified and directed

S&F Aluminium decorative grill of section size of mesh 50mm & 4mm dia fixed to window including frame works complete all as specified and as directed.

S&F for venetian blind for window horizontal or vertical with laminated wing metal type including all accessories make : VISTA or equivalent all as directed by Engr-in-charge

Supply and Fixing stainless steel curtain rod fancy type minimum 25mm diameter, minimum 1.25 mm thickness of best quality along with matching knobs at the end and brackets for holding the rod complete all as specified and as directed.

S&F 2nd class hard wood plain, solid, straight chowkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified.

M&L for PCC 1:2:4 Type B0 (12.5mm graded stone aggregates) as in hold fast etc complete all as specified and directed.

M & L treating ends of posts, backs of chowkhats etc area not exceeding 0.1 sqm each but n exceeding 0.5 sqm each

M & L for treating small articles such as stops covers, gully gratings ,hold fast, ends of posts, backs of chowkhats etc area not exceeding 0.1 sqm each

S&F bands, straps, supports or stays for rainwater, large hasp and staple, chains, clamps, hold fasts, wall ties etc and small articles confirming to Fe290 Gde-E-165, complete all as specified and as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rails on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, fixing in the frame at site as per specification & drawing given in SSR Part I

S & F Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforcement with M.S square tube, complete all as per specifications given in SSR Part I

S&F factory made 35mm thick flush shutter solid core construction with block board core with decorative face veneered both side etc complete all as specified and directed

S&F Aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) 300mm size and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete

S&F Butt hinges, medium weight, cold rolled mild steel, size of hinges 100mm.

S&F aluminium anodised barrel bolts and fixed of 200 mm length

S&F Extruded Aluminium, anodised, bow handles of size 150mm.

M&L for preparation of new or previously untreated surfaces of wood and wood based materials of any description not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint complete over a coat of pink primer all as specified and as directed.

M&L for old steel surfaces of any description exceeding 10 cm in width or girth when unconnected with other painting surfaces complete all as specified and directed by Engr-in-Charge.

M&L for 18/19 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination as in kitchen cabinet/cup-board completed all as specified and directed.

S&F Continuous (Piano) hinges, brass, width of flaps 30 mm (when open)

S&F Magnet catches for cupboard shutter, brass body with striking plate including letting in all as specified and as directed

S&F Extruded brass handles, 100 mm size, fabricated type, polished all as specified and as directed

S&F Anodised Aluminium Hasp and staple 100mm size, including bolt to hinge plate and fixed with screws

S&F 6.3mm thick plain glass frosted for fixing name board including fittings

M&L for PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in surface channel and drains complete all as specified.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc all as specified and directed.

S & F vitrified coloured external paving tiles of size 30 cm x 30cm x 9/10 mm thick set, jointed & pointed in neat cement slurry with grey cement and matching coloured pigment in floor over screed bed complete all as specified . (Note :- Screed bed will be measured & paid separately)

M & L for 15mm thick screed bed in CM 1:4 , bedded, jointed for fixing tiles etc

M&L for 100mm thick cement concrete using (40mm graded aggregate) type D-2 (1:4:8) as in sub base

S & F coloured vitrified out door exterior designer tiles for wall cladding of size 300x600x6/8 mm thick set, jointed & pointed in neat cement slurry with grey cement and pigment over and including 10mm thick backing coat in CM 1:4 complete as specified and directed

S&F Rolled mild steel sections of Fe-290 (Gde E-165) as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails, fixed with angle cleats or other connecting plates, complete all as specified and directed.

M&L for two coats of synthetic enamel paint on steel surface exceeding 10 cm width or girth over a coat of primer (Red oxide Zinc chrome) including preparation of surfaces complete.

M&L for 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in path, plinth protection, sub-floors etc finished even and fair or even and rough as required complete all as specified and directed

M&L for complete removal of existing treatment on surface of wall and applying two coats over a coat of distemper oil emulsion over a coat of primer over and including minimum 1.5mm thick layer of white cement based wall putty complete all as specified and directed by Engr-in-charge

M&L for complete removal of existing old treatment of wall of any description and preparation of old surfaces ,washing rubbing down and applying two coats weather proof acrylic emulsion paint over a coat of exterior suitable primer complete all as specified and directed.

M&L for complete removal of existing treatment on old surfaces and applying thin layer(minimum 1.5 mm) of white cement based wall care putty including preparation and applying two coats of plastic emulsion paint over a coat primer complete all as specified and as directed.

M&L for 12mm thick Plywood, grade BWP, type BB fixed with screws to timber frame work

M&L for decorative laminate type 1 of 0.9 mm thickness & surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturers instructions.

M&L for brass mortise door lock 2 lever, size minimum 65mm with handle and concealed body. Make : Godrej/ Harrison / Link

S&F in repairs CP Towel Ring square or round of continental series of Cat No ACN 1121N of Jaquar complete all as specified and directed.

S&F in repair CP Soap dish continental series of Cat No ACN 1131N . Make-Jaguar

S&F in repairs CP Toilet roll holder with stainless steel flap of continental series of Cat No ACN 1153S complete all as specified and directed. (Make-Jaguar)

S&F in repairs Concealed stop cock, Chromium plated, 15 mm, all as specified and directed. (Make- Jaguar, Cat No-CON-083FTK)

S&F bib cock 2 two way double handle with flange and fixed complete all as specified and directed. (Make-Prayag, Cat No 7212)

S&F in repairs bib cock with wall flange of continental series of Cat No CON-047KN fixed complete all as specified and directed. (Make-Jaguar)

S&F in repairs 15mm bore CP health faucet (ABS body) with 8mm dia ,1.2 mtr long flexible tube and wall hook complete all as specified and directed (Make - Jaguar, Cat No - ALD-CHR-593N)

S&F in repairs corner glass shelf with brackets) complete all as specified and directed (Make - Jaguar, Cat No ACN-1173)

S&F in repairs glass shelf 600 mm long complete all as specified and directed (Make - Jaguar, Cat No - ACN-1171N)

S&F in repairs shower basket small complete all as specified and directed (Make - Jaguar, Cat No-ACN-1177N)

S&F in repair Water closet Pedestal pattern, single peace WC with UF soft seat cover , hinges, fixing accessories set , cistern fittings of size 395x710x780mm of queen's series Cat No 7851S of Jaquar complete all as specified and directed Make-Jaguar of equivalent in Marc/Kohler

S&F in repairs Vitreous china WHB, white, wall hang basin with fixing accessories Size-590x490x185mm Lyric model Cat No 38801 of Jaguar including half pedestal with fixing accessories set complete all as specified and directed. Make-Jaguar or equivalent in Marc/Kohler

S & F in repairs CP Towel Rack 600mm long without lower hunger but with three hooks of continental series Cat No ACN 1181FHN complete all as specified and directed. (Make-Jaguar or equivalent in Marc/Kohler)

S&F in repairs looking mirror size 600mmx600mmx6mm with frame wooden plugs with chromium plated brass screws and cup washers complete all as specified. (Make-Prayag, Cat No - BLM-02F)

S&F in repairs swivel mirror of continental series of Cat No ACN 1195N complete all as specified. (Make-Jaguar or equivalent in Marc/Kohler)

S&F in repairs 15mm bore CP wall mixer 3-in-1 system with provision for bath hand shower and overhead shower complete with 115mm long bend pipe , connecting Legs & wall flange (without hand & overhead shower) complete all as specified and directed (Make - Jaguar/Marc/Kohler)

S&F in repairs 15mm bore CP centre hole basin mixer with pop up waste system with 450mm long braided hoses of continental series of Cat No CON-169KNB of Jaquar complete all as specified and directed (Make - Jaguar or equivalent in Marc/Kohler)

S&F in repairs 15mm bore overhead shower 190mm round shape single flow (ABS body chrome plated with grey face plate) with rubit cleaning system complete all as specified and directed (Make - Jaguar, Cat No - or equivalent in OHS-497N, Marc/Kohler)

S&F in repairs 15mm bore hand shower 140mm round shape multi flow with air effect (ABS body & face plate chrome plated) with rubit cleaning system complete all as specified and directed(Make - Jaguar, Cat No HSH-1729 or equivalent in Marc/Kohler )

Taking down carefully old unserviciable copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, sunken type box etc. and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge.

M&L for point wiring for modular fittings with 1.5 Sqmm (nominal area) PVC insulated1100 volts grade, multistranded, copper conductor, single core, unsheathed cables (FRLSH quality) drawn through and including PVC conduits of suitable size but not less than 20 mm dia (medium grade) with all fittings and accessories including suitable modular or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally concealed in walls/ceiling etc and including cutting chases for conduits and sinking for boxes and making good to disturbed surfaces, including PVC insulated and unsheathed, single core, multi-stranded, copper conductor cable of size 1.5 Sqmm green in colour as earth continuity conductor connected to common earth and earth dolly for one light point controlled by one 5 Amps one way switch complete as specified and directed. Note : Quoted rate shall be inclusive for necessary chasing and cutting and making good .

Description all as per Srl item No.108.00 here in before but for one fan point controlled by one switch/ fan regulators.

Description all as per Srl item No.108.00 here in before but for one light point controlled by two way switch/fan regulators.

Description all as per Srl item No.108.00 here in before but for one bell point controlled by one bell push.

All as per item No 108.00 above but for one 3 pin socket outlet 5 Amps on same board alongwith other suitable switches.

All as per item No 108.00 above but for one 3 pin socket outlet 5 Amps on independent board alongwith other suitable switches.

All as per item No 108.00 above but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point) complete all as specified.

Supply and fixing of modular switch one way 6 amps 1 module 230/250 Volts complete all as specified/directed.

Supply and fixing of modular switch two way 6 amps 1 module 230/250Volts complete all as specified/directed.

M & L for Quick sensor (Qs-11) 180 degree wall mount PIR motion sensor switch with light sensor suitable for 230 volts, 50 Hz including one nos door magnetic switch complete all specified and directed

Supply and fixing modular bell push 1 way 6 A module 230/250 volt , AC supply, complete all as specified and directed.

Supply and fixing of modular socket outlet 2/3 pin 6 Amps 230/250 volts 2 module complete all as specified/ directed.

Supply and fixing of modular socket 6/16 Amps, 230/250 volts, 2/3 pin combined, 2 module complete all as specified and directed.

Supply and fixing of modular white cover plate with frame 1 module

Supply and fixing of modular white cover plate with frame 2 module

Supply and fixing of modular white cover plate with frame 3 module

Supply and fixing of modular white cover plate with frame 4 module

Supply and fixing of modular white cover plate with frame 5 module

Supply and fixing of modular white cover plate with frame 6 module

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified.

Supply and fixing call bell ding dong, AC, 230 V, Single pole all as specified and directed. Make- Havells/Legrand.

Supply and fixing LED batten fittings 1x18 Watt complete pre wired fixed to wall with 2 nos PVC block of suitable size Make- Philips Linea Plus HSN code 94051090 (WW) or equivelent model of Havells/bajaj

S & F wall mounted LED batten fittings with all accessories 1X 10 Watt LED 6000K , extruded polycarbonate, integrated electronic driver and fixed to wall with 2 Nos PVC block suitable size complete all as specified and as directed Make- Philips Astra Line Scene Switch HSN Code- 94021090 or equivelent model of Havells/bajaj

S & F Slim design LED recessed square type down lighter 12 watt flat panel PDC aluminium housing and PMMA diffuser all as directed and specified Make- CG Cat No- LSCSM-18W-WW or equivalent model of Havells/bajaj

S & F Wall decorative LED light fitting with lamp 7.5 Watt complete with necessary connection Make:- Philips cat Part No Dew Wall lamp LED chrome 7.5W chrome or equivalent in bajaj/ Havells

S & F Wall bracket decorative LED Foot light 12 Watt complete with necessary connection complete all as specified and directed. Make:- Philips cat Part No 309742 watt LED spot light, wharm or equivalent in bajaj/ Havells

S & F Wall Spot Light LED Light / fitting with lamp E14 Base LED 10 Watt complete with necessary connection complete all as specified and directected. Make:- Philips cat Part No 32029/11/66 Aqualit wall light chrome and metal or equivalent in bajaj/ Havells

Supply and fixing of hot water Geysers of 25 ltrs capacity 5 star rated vertical type including fixing of bolts , nuts grouted into the wall, and necessary cement work, making good of disturbed surface of wall, giving electric and water connection and testing after installation. Make : Havells cat part no - GHWCARTWH025 or equivalent in LG/Racold.

S&F heat resistant PVC connection pipe for hot and cold water 450mm long 15mm dia. Make: Prayag or equivalent in Polytuf/ Havells.

Supply & laying galvanized steel tubing, medium grade laid in trenches/floor/wall and joined including necessary fittings such as bends, elbow, tees, sockets, etc for 15mm dia pipe.

S&F bib taps, 15 mm, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed.

S&F angle stop valve cast copper alloy, chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixing of size 15mm.

Supply and fixing in repair single three phase digital electronic meters with LCD Display 5-30 Amps Cat Part No WR300BC7300 Make :- L&T including taking down old unserviceable meters to store and including connection and complete all as specified and directed as specified.

S & F Exhaust fan 230 volts , 250mm,plastic body including making all electric connection complete all as specified and as directed including cutting of hole on wall and making good disturbed surface of wall and outer wooden box for fixing fan on wall Make Bajaj/Havell's/CG.

Supply and fixing LED security Building light LED 25 Watt , pressure die cast aluminium housing, heat resistant glass, IP65 protection, better optics for uniform distribution complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light complete. Make:- Bajaj Cat part No- 169821 LED/CG as per cat No LSTO 25 CDL equivalent model as in Surya / havells .

Supply and fix in repairs MCB DB 4 way vertical sheet metal enclosure TPN 415 volts, 50 Hz, with IP-43 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting complete all as specified. (Note : 1. MCB SP/TPN shall be measured and paid separately under appropriate items of this schedule . 2. Copper thimble shall be used for connection of cable. )

Supply and fix MCCB TPN, 63 Amps, 16 kA rupturing capacity 415 Volts complete all as specified and directed.

Supply and fix MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series complete all as specified and directed.

Supply and fix in repairs MCB, single pole 240 volts 6 to 32 Amps capacity 'C' series fixed in DB's.

Excavation in trenches not exceeding 1.5mtr. in depth and not exceeding 1.5mtr in width and getting out in soft/ loose soil for laying of cable etc

Returning, filling in trenches, spreading ,levelling, watering and well ramming in layers not exceeding 25cm thick.

Removing excavated material/ surplus soil and depositing where directed at a distance not exceeding 50mtr.at a level not exceeding 1.5 mtr from starting point.

Supply lay and spread in trenches , river sand ,clean ,including spreading ,levelling ,punning for laying /cushioning of cables all as specified and as directed.

Supply and lay in trenches fly ash bricks, old size sub class “B” for cable protection.

Supply and lay in trenches, floors ,fix on wall/pole, passing through pipes etc.,LT UG cable ,1100 volts grade, PVC/ XLPE insulated , with multistranded aluminium conductors, armoured with galvanised steel wire or tape ,gland, lugs etc, of 16 Sq.mm 4 core , confirming to IS specifications including taking down old one.

Supply and fix on pole / wall or lay in trenches under road / drain crossings etc., for drawing cables, GI pipe light grade 40 bore dia , ISI marked including necessary fittings ,clamps, bolts , nuts etc.

M & L for Sub main wiring with two run single core 6 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia concealed on wall/ceiling in PVC conduit, medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 6 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion including taking down old wiring etc complete all as directed. Note: (i) Two runs of 6 sqmm and one run of 6 sqmm cable and one run of PVC conduit shall be measured as one RM. (ii) Cutting of chases in the wall of appropriate size shall be carried out with electric cutter machine . (iii) Necessary plastering in the disturbed surface of wall and distempering /white washing to match the existing colour shall be included in the unit rate quoted.

S&F Factory made (Dust and power Jet Proof according to IEC 60529) opaque junction box of size 600 x 300mmx 170 mm made of high quality polycarbonate (shock proof, rust free, corrosion free acid and chemical resistant, fire retardant having high impact (IK 08) totally insulated made of halogen and silica free recyclable material, UV resistant having high grade gasket made of polyurethane with copper terminal , with locking arrangement suitable for fixing TPN DB 4 way and energy meter single phase with glass for showing meter reading and 2 Nos M40 size cable gland and one M32 size gland suitable up to 16 Sqmm cable etc complete all as specified and directed including taking down old unserviceable junction box.Make : HENSEL/Sintex.

Material and labour for earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers ,galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown in Electrical Plate No 3 of SSR part -I.

R K CONSTRUCTION

M/S UTTAM SAHA

KB Singha and Associates

Lyngdohs Construction Company And Associates

M/s Kharsyntiew Industries

M/s Nishi Kumar Das

H K Enterprise

M/S GOSWAMI COSTRUCTION