Installation of 02 Nos. High Mast Lights in Honble CM Residence in VIP 1 at Wazarat Road Jammu.

Supply of Medium Light mast 11 M long, Steel Tubular (SP-410, SP-56), duly painted with two coats of red oxide and two coats of silver paint, made up of mild steel pipe conforming to IS 2713 part I & II of 1980, with length of sections."

Supply/fabrication/installation of mild steel ring having Diameter of the adjustable ring = 1800mm, dia of the steel pipe of the ring = 50mm. 4 No's of supports of 50mm dia pipe duly welded between inner periphery of the ring and the cap. The length and diameter of the cap of the adjustable ring is such that it should be well fixed on top of the Mast and give an overall aesthetic look to the Mast. The cap of the ring shall have 4 No's holes welded suitably with 4 No's nuts to facilitate tightening of the ring on the top of the Mast. On the periphery of the ring, the holes of suitable size shall be provided to fix four to six No 1 * 200 watt LED Luminaries. The main and supporting pipe of the adjustable ring should be hollow throughout, facilitating the routing of Cu. Cables requires for connections.

Erection of steel tubular or rail pole strut in cement concretę 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 40mm nominal size) foundation including excavation and refilling and secured with holding clamps bolts nuts etc as required.

Supply, installation, testing and commissioning of feeder piller. The feeder pillar shall comprise of controlling switch gears and a 1-Ph. LT Servo controlled automatic voltage regulator. A single unit, outdoor type made out of 16 SWG cold Rolled Sheet Steel, Powder Coated from Inside & Outside, slopping head forward at a suitable angle and overhang to provide complete protection from water and moisture provided with lockable hinged doors, dust and vermin proof, having Digital Time device for automatic switching off the lights at pre fixed time, and all duly wired up with following accessories. a) Incoming 63 Amps, DP MCB 01 No. b) Outgoing 16/10 Amps, SP MCB 06 Nos. c) Neutral Link, 5 Way 01 No. d) MCB 6/12 amp C-type single pole.-1No e) ML 2 AC Contactor reputed make 01 No. f) Digital Time Device (reputed make)/ any ISO unit -1 No. g) 2 KVA, 1-phase, LT servo controlled automatic voltage regulator suitable for unbalanced input voltage range 120-250V& output 230V +-2% with overload & short circuit protection, duly provided with voltmeter, auto/manual control, indicating lamps, etc. h) Panel should be of galvanized iron IPP 66 protected, powder coated size 2ft x 2.5 ft. x 1 ft., made up of sheet of 16 SWG. i) ON/OFF & START/STOP push buttons with indicators cost of cement concrete 1:4:6 (1 cement: 4 coarse sand: 6 stone aggregate) to be included in the rate offered for each item and comprising of following as per specification and SLD (Complete Job).

LED Flood Light, powder coated pressure die cast aluminium (System lumen efficacy >135 lm/Watt) Supplying, Installation, Testing & Commissioning of Flood Light, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%,Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection,EMI-EMC as per CISPR-15, lenses for beam angle 30 deg-120deg as per the application and the project requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junctiontemperature shall not rise above 90°C). 200 watt.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 Meter long etc.with charcoal/ coke and salt as required.(For feeder pillar)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.40mm

16 mm² Cable (2C) from LT Line to meter ,1.1k V Grade, AL.,Armoured, PVC Insulated Stranded Conductor FRLS type reputed make.