8996/GWL/E8 PROVN OF OPERATIONAL ROOM IN THE AREA OF AGE B/R-I UNDER GE GWALIOR

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations etc or for shafts, well cess pits, manholes, pier holes, etc but not exceeding 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

M&L for Plain cement concrete (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundations / mass concrete complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, base for coloumns and mass concrete etc complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 (using 20 mm graded stone aggregate) as in coloumns, pillars, piers, posts and struts etc complete all as specified and directed.

Removing excavated material exc 250m but n.exc 500 mtr and depositing where directed at alevel n.exc 1.5m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick each layer in loose/soft soil complete all as specified and directed.

M&L for formwork to sides of concrete, in foundations, footings, base of columns & plinth beams etc in flat for rough finshed surfaces of concrete complete all as specified and directed.

Formwork to Columns, square/rectangular, rough finish surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars, 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars 5 mm and over upto and including 10 mm dia, as in stirrups, spacers, and binders, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Moorum/red bajri filling in floors or pavings, laid in layers n.exc 15 cm thick each layer spread, levelled and rammed including watering as required complete all as specified and directed.

M&L for hard core of broken stone boulder of gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

M&L for 100 mm thick PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in sub base for floor, finished even and rough complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B-0, (using 12.5 mm graded stone aggregate) as in levelling coarse for floor, finished even and rough complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C1 (using 20 mm graded stone aggregate), finished even and smooth without using extra cement as in plinth protection including forming of joints 10mm wide and 75mm deep and joint filled with bitumin and sand mixture in 1:1 ratio complete all as specified and directed.

M&L for Vitrified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 as in floors complete all as specified and directed.

M&L for Brick work with fly ash bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for 15mm thick rendering on brick or stone/concrete any surfaces in cement mortar 1: 4 on mixed with WPC @ 0.4% by weight of cement, surface finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured & paid seperately.

Supply only integral liquid water proofing compound (ISI marked) complete all as specified and directed.

Preparation of new plaster surfaces of wall, and applying two coats of distemper oil emulsion over a coat of 1mm thick wall putty & over a coat of chalk whiting, on plastered surfaces, preparatory to distempering complete all as specified and directed.

M&L for Preparation of new plaster surfaces of wall, and applying two coats of cement base paint over priming coat of alkali resistant primer complete all as specified and directed.

M&L for Preparation of new plaster surfaces of ceiling, and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

BUILDING SOLUTION FOR TRUSS AND WALL SYSTEM : Design, Supply and fixing of Pre-fab Truss Roofing Structure & smart wall for barracks with factory finished, custom designed cold formed light gauge steel frame super structure manufactured out of 0.75/1.0 mm BMT (base metal thickness). Pretreated, factory finished bare zincalume or equivalent (AZ150 GSM Aluminum Zinc Alloy coated steel and 550 Mpa yield strength) conforming to AS/NZS 4600-2005 and also shall be as per IS: 8750-1987, IS: 800-1984 Part II conforming to equivalent AS/NZS. The wind loads shall be as per IS: 875 (Part III). The truss & wall framing section shall be cold form, C type having minimum depth of 75mm x 40mm in required length as per structural design requirements as per approved drawings. The C-Section to have 2 grooves on web with minimum R-2.5. The truss purlin members should be manufactured from zincalume or equivalent (min 150 gsm & 550 MPA) steel of base metal thickness 0.75/1.0 mm and shall be top hat TS41 (41 X 32) or TS61 (61 X 36.5). The wall members should be manufactured from zincalume (min. 150 gsm & 550 MPA) steel of base metal thickness 0.75/1.0 mm. LGSFS frame shall be designed as per IS: 801 using commercially available software SUPRACADD or relevant. The frame can be supplied in panelized or knock down condition, in specified dimension and fastened with designed screws.

ROOF SHEETING: Supply & fixing of Zincalume trapezoidal roof sheet with effective width of 1015 panels are roll formed from nominal 0.42 mm base metal thickness of minimum yield strength of 550 MPA, coated with an aluminum/zinc alloy (i.e.Zincalume or equivalent), AZ150 (min 150 gm/m2 total on both side), conforms to Australian standard AS1397, The steel manufacturer's test certificate for the chemical and mechanical properties of steel must be submitted for approval by the concerned authority prior to installation. The sheet shall have brand marking of the manufacturer giving product details on the back of the sheet at every 1 meter c/c for confirming genuinity of the material. Profile dimensions: Trapezoidal type profile sheet shall have 1015 mm effective cover width, 28 mm deep ribs with subtle square fluting in the five pans at 203 mm centre to centre. The end rib shall be designed for anticapillary action, to avoid any seepage of water through the lateral overlap complete all as specified and directed.

External Walls Cladding : COLORBOND LYSAGHT Panelrib profile sheet of 1110 mm Supply width. The feed material is manufactured out of nominal 550 MPA yield strength, metallic hot dip coated with Aluminum-Zinc alloy (55% Aluminum, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 200 gms/sq.mt total on both sides) with Colorbond quality paint coat as per AS/NZS 2728 Class 3 of Tata BlueScope Steel make. The paint will have a total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior coat on top surface and nominal 5 μm reverse coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade by concern authority. The sheet shall have brand marking of the manufacturer giving product details on the back of the sheet at every regular interval for confirming genuinity of the material complete all as specified and directed. Total thickness : 0.50 mm : Ceiling sheet : Spandek/Cutom ORb/Panelrib. Colour : As per clients approval

Providing and fixing internal wall panels on Light Gauge Steel Frame work with 12.5mm thick gypsum plaster board conforming IS 2095:2011 fixed on 8mm thick fiber cement board conforming to IS 14862:2000 of category Ill type B (High pressure steam cured) as per standard sizes fixed with self-drilling/taping screws/fasteners@60cm c/c of approved make, Screws shall be counter sunk rib head of 1.60mm to 4mm thick of 8 to 10 gauge of length varying from 25 to 45mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish complete all as specified and directed. (cost of frame work to be paid for separately).

Fill the groove (i.e. 2-3 mm gap between boards), taping and jointing 8mm thick fiber cement board and 12.5 mm thick gypsum plaster boards with epoxy based sealing compound, acrylic based sealing compound, non woven reinforcement tape as per direction of Engineer in Charge. (Use a flexible knife so that no air bubble is entrapped. Allow 1-2 hours gap. Once hard tacky or set, apply a coat of acrylic based sealing compound paste to flash fill the beveled area. After 2-4 hours go on to repeat a skin coat with acrylic based sealing compound to securely embed the 40mm width non woven reinforcement tape. Use only flexible steel knife, such as provided with packs, to avoid air entrapment within compound. After overnight drying shrinkage apply a coat of acrylic based sealing compound to compensate shrinkage. Finally cover the bevel portion with any suitable overall skin coat with a desired full surface-leveler material complete all as specified and directed.

False Ceiling : Fixing 12.5mm thick gypsum plaster board conforming IS 2095:2011 which is screwed on the base of AZ150 Roof Truss conforming to IS 14862:2000 of category type B (High pressure steam cured) as per standard sizes fixed with self-drilling / taping screws / fasteners @ 60cm c/c of approved make, Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick of 8 to 10 gauge of length varying from 25 to 45 mm. Proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish. No cove false citing basic gypsum flat false ceiling complete all as specified and directed.

False ceiling : Extenral - COLORBOND LYSAGHT Panelrib profile sheet of 1110 mm Supply width. The feed material is manufactured out of nominal 550 MPa yield strength, metallic hot dip coated with Aluminum-Zinc alloy (55% Aluminum, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 200 gms/sq.mt total on both sides) with Colorbond quality paint coat as per AS/NZS 2728 Class 3 of Tata BlueScope Steel make. The paint will have a total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior coat on top surface and nominal 5 μm reverse coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade by concern authority. The sheet shall have brand marking of the manufacturer giving product details on the back of the sheet at every regular interval for confirming genuinity of the material complete all as specified and directed. Total thickness : 0.50 mm : Ceiling sheet : Panelrib 1110 Colour : As per clients approval

S&F for 12 mm Toughned Glass work including Door & accessories complete all as specified and as directed.

M&L for wall paneling upto height of 1.20 mtr for internal walls finished - final finish as wood planks complete all as specified and directed.

S&F for 19 mm thick PVC Celuka board of one side plain white colour fixed with screws, solvent cement/adehesive including sliding with heavy roller and channel etc complete accessories complete all as specified and directed.

Roof Insulation: Providing & Fixing 8 mm Bubble insulation with aluminum foil on either side as protection laid over the top of purlins, complete all as specified and directed.

Wall Insulation: Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having held and in position by criss crossing GI wire etc complete all as specified and directed (density 48 kg/m3,50 mm thick, wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers) complete all as specified and directed.

Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc as specified erected in position and securing runners with hold fasts and brackets complete all as specified and directed.

M&L for concealed point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed non metallic rigid PVC conduit medium grade confirming to IS 14930 (Part-I) 2001 (ISI marked with valid CML No) not less than 20 mm dia with all fitting and fixing accessories and 1.5 Sqmm FRLSH, PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel modular sunken terminal boxes factory made duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches sockets etc complete all as pecified and directed.

One light point controlled by one switch.

One Ceiling fan point controlled by one switch.

One Exhaust fan point controlled by one switch.

One 5 pin multipurpose socket out let 5/6 Amps on the same board with other switch.

One 3 pin/5 pin switch socket outlet, 5 Amps on independent board.

Description all as per item No 36 here in before but point wiring with 2.5 sqmm FRLSH confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire ONLY for power point complete all as specified and directed.

S&F Modular switch 1 way 6A,1 module complete all as specified and directed.

S&F Socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.

S&F Modular switch 1 way 16A, 1 module 15 Amp complete all as specified and directed.

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

S&F Fan step regulator, 120W - 2 module 240 volts, AC 50Hz complete all as specified and directed.

S&F Track mounted LED COB light with high efficiency, housing made of extruded aluminum, 20 Watt 4000K along with 2 meter suspension hanging 5 track light on it complete all as specified and directed.

SITC of 33W Tunable 2700K TO 6500K CCT 2ft by 2ft Recessed LED Light with System Lumens of 3300 Lumens 100 Lumens per watt. Made up of CRCA Powder Coated PMMA Diffuser. Product is of IP20, Input Voltage Range 198-264V, LED Efficacy greater than 150Lumens/watt, LED Life 50000 Burning Hours, CRI >80, Surge Protections 2KV, DALI Type 8 Driver. Wipro CRCO10R036HP2765 or similar in LT & Trilux. Complete all as specified and directed.

DALI Controller Suitable to Control 4 Nos of Fixtures and can be controlled via Mobile Apps bluetooth based iSense Controller AFD1/4 is a DALI controller and operates on 90-277VAC input voltage range. It can be connected to 4 DALI LED drivers. This device also has a 12VDC auxiliary output to power the sensors complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F Projector Ceiling Mount with Tray for Projector Camera, Carbon Steel Projector Mount for Business Conferences-Angle Height Adjustable Wall Ceiling Mounting (2 Feet) complete all as specified and directed.

S&F Adjustable, foladable LED stand of stainless steel grade for 65/55 inch (as direction by engr-in-charge) fixed on wall and foldable re-adjustable construction as per direction of Engr-in-Charge complete all as specified and directed.

S&F LED round luminaire 15 watt, 220 Volts, 6500k > 110 lm/watt luminous efficiency AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling incluing connecting upto drive with reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor for electrical connection to connector of LED fitting including testing on completion complete all as specified and directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade confirming to IS 14930 (Part-I) 2001 (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLSH copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. NOTE: (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

M&L for sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 4 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade confirming to IS 14930 (Part-I) 2001 (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLSH, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. NOTE: (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

S&F sheet metal enclosure double door for distribution board factory made for MCB DB load link VTPN 4 way suitable for MCCB as incomer, 100 Amp, 4 pole & Including MCCB 100 amps 4 pole 16 KA complete. (when MCB's are to be used) with suitable size of busbar complete fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down complete all as specified and directed.

S&F MCB DB, sheet metal enclosures double door SPN 12 way with bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F MCB DB, sheet metal enclosures double door SPN 8 way with bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F, MCB SPN 63 Amps, 240 volts 'C' series 16 KA, including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SP 240 volts, 6 to 32 Amps, 'C' series 10 KA including connection with suitable size copper lugs complete all as specified and directed.

Supply and installation and testing of earthing electrode 3.0 mtr length, galvanised outer dia 88mm and inner dia 48mm and the cavity between the rod pipes filled with ground resistance improvement powder, sealed with both end the outer pipe of electrode should be Zinc coated, the electrode should buried directly in ground by making boring of diameter 10" with boaring machine highly connected with GI strip of size 25x3mm of 2 to 3 mtr length to facilitate further connection to earth dolly and provision of earthing chamber in bricks wall size 45x45x15 cm and having PCC cover of required size complete all as directed and all as per IS 3034(1981).

S&F for modular plate and provising of new modular plate of different size including fixing, the existing modular switchs, modular socket, modular regulator and refixing them in new board. Note : Renewal of any switches, sockets, fan regulator will be measured under separated items.

White cover plate with frame but 2/3/4 module

White cover plate with frame but 8 /12 module

Supply and fixing of GI trunking along with 3 m mat aluminium finish popbox with floor back box including flowing item under :-

Trunking 75mm X 38 mm (GI)

Fixing bracket 75 x 38 mm

ADJ JB 150 x150 x 65-90 mm

Popup aluminium 3 mod

Backbox concrete popup 3 mod

6 Amp switch SP 1w1m AR

6 A 3 Pin socket white

20 amp switch indipendent SP 1W1M AR

6/16 3 pin shutter skt 2m ar

Supply and install Tower type units indoor complete with cordless remote control unit and with inbuilt Heating and Cooling arrangement and Digital Inverter twin rotary compressor, single phase units 220V - 240V, 50 Hz of capacity of 4.0 tonnage complete all as specified and directed.

Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 3 star rating and EER 3.2 of capacity 1 TON complete all as specified and directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of but of capacity 5.0 KVA complete all as specified and directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5%and of capacity 2 KVA complete all as specified and directed.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and directed.

Supply, laying and testing of cable XLPE insulated, armoured, heavy duty, electric LT UG cable of size 35 Sqmm x 3.5 Core with multi stranded aluminium conductor, 1100 Volts grade complete all as specified and directed.

Removing excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as directed.

M&L for sand filling/cushioning in trenches for cable protection including consolidation complete all as directed.

Supplying and laying unreinforced precast concrete cable cover, class but Class LV, Type I, flat, size 250 mm x 150mm x 40mm complete all as specified and directed.

M&L for Cable joining kit for LT cable for outdoor termination heat shrink type joint complete with joining material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 25 sqmm to 95 sqmm complete all as specified and directed.

S&F tube 'Light' grade galvanised with all fitting laid in trenches, fixed to wall and floor of 40 mm dia for cable protection complete all as specified and directed.

Utopia Constro (BID ID -3130948)