PROVN OF 03 GD POSTS ADDN ALTN TO BLDG NO NP 01 AND PROVN OF CHAIN LINK FENCING WITH GATE UNDER GE SOUTH UDHAMPUR

Amount

Demolition of cement concrete (unreinforced) in ground floor and in paving exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Demolition of brick/stone masonry including all necessary arches, pillars,quions etc built in cement mortar complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.60mm thick crimpted/tapard at the external end slope of any colour having tensile strength 550 Mpa as in roof covering fixed with self tapping screws and caps etc complete all as specified and directed

Plain galvalume aluminium zinc coating GI based plain steel sheet 0.63mm thick in ridges, hips, valley gutters at the external end slope of any colour having tansile strength 550 Mpa as in roof(ridges) covering fixed with self tapping screws and caps etc complete all as specified and as directed.

Rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of gde Fe-410W (Gde E-250 quality), complete all as specified and as directed.

AC designer composite ceiling board 4 to 6mm thick in 600x600mm panel conforming to IS-14682 TYPE-B category-3 including GI frame, holdfast and suspenders complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved on plan exc. 6.00m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as specified and as directed.

Providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Screed bed or bedding layer of mortar 10 mm thick for laying floor tiles in CM 1:4 completed all as specified and as directed.

Digital vitrified ceramic tiles 10 mm thick ( square / rectangular ) polished dark /light shade , doubble charged/ultracharged tile areaof each tiles n. exc 0.36 sqm but n exc 0.42 Sqm in floors etc and jointed in neat cement slurry and pointed in white or coloured cement to match the work using dark shade complete all as specified and as directed.

Rendering 10 mm thick on fair faces of brick /concrete surfaces in cement mortar 1:4 as in backing coat to recieve tiles as in vertical surfaces and finished even and fair complete all as specified and as directed.

Glazed coloured ceramic tiles in dado/vertical surface (300x600mmx 7mm) thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specified and as directed.

Non skid coloured ceramic tiles (square/rectangular) 8 to 9 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed.

Marble work 20 mm thick (table rubbed and polished, moulding ) in steps, jambs,pillars, window cills, cooking platforms and like in cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade black (Black Zebra Bhainsalana) complete all as specified and as directed.

Rendering 15mm thick in two layer (10+5 mm) on brick work or concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately) complete all as specified and as directed.

Supply only (LW+) water proofing liquid solution of Dr fixit/sikka or equivalent make complete all as specified and directed.

Preparation of newl surfaces and applying two coats of Cement base paint on walls complete all as specified and as directed.

Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

Two coat of Oil bound distemper including a coat of primer over a layer of birla white putty including preparation of newly plastered surfaces of wall complete all as specified and as directed.

Preparation of steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of zink chrome primer complete all as specified and as directed.

Old steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth and getting out in Hard/dense soil complete all as specified and as directed.

Returning, filling in trenches including spreading, leveling watering and well ramming in layers not exceeding 25cm complete all as specified and as directed.

Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as directed.

Shingle filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering complete all as specified.

Hard core of broken stone of guage n.exc 63mm deposited spread and levelled in layer n.exc 15cm thick watered and well rammed to true surfaces complete all as specified and as directed.

75mm thick Cement concrete 1:2:4 type B-2, (40mm graded crushed stone aggregate) as in sub base complete all as specified and as directed.

25mm thick, Plain cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in sub base complete all as specified and as directed.

PCC 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in filling mass concrete in foundation complete all as specified and as directed.

Material and labour for providing Reinforced Cement Concrete M - 25 design Mix using 20 mm graded crushed stone aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc all as specified and as directed.

Material and labour for providing Reinforced Cement Concrete M - 25 design Mix using 20 mm graded aggregate as in columns, pillars, piers, posts and struts complete all as specified and as directed.

Material and labour for providing Reinforced Cement Concrete M - 25 design Mix using 20 mm graded crushed stone aggregate as in beams, cantilever, lintels over 1.5 m complete all as specified and as directed.

Material and labour for providing Reinforced Cement Concrete M - 25 design Mix using 20 mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like over 1.5 m complete all as specified and as directed.

Material and labour for providing Reinforced Cement Concrete M - 25 design Mix using 20 mm graded aggregate as in Chajjas and like complete all as specified and as directed.

Use and waste formwork to sides of concrete foundation footings base of coloumns sides and soffits (if any) of foundation and plinth beams, and similar work vertical or to batter for rough finished flat surface of concrete complete all as specified and as directed.

Use and waste formwork to sides of columns, pillars, posts, struts, piers and stanchions, rectangular or square for rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste formwork to sides and soffits of floor or roof beams, beam hunching, girders, lintels, cantlievers, shelves including supports, etc for rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, la ndings and similar work; not exceeding 200 mm thick (Horizontal or slopping) for rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste of form work to edges of flats, slabs etc including fair finished surface all as specifed and directed.

Material and labour for 10 mm dia and over Mild Steel TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed.

All as per item No 45 above but 6 to 8 mm dia complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt ), complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and as directed.

Glazed anodised (15 micron) powder coated Aluminium door made out of extruded section as standard door frame, single groove of size 100 x 45 x 2.5 mm thick standard shutter top and bottom section of size 95 x 45 x 2.5mm thick standard shutter vertical section of size 80 mm x 45 mm x 2.5 mm thick complete with auto hydraulic floor mounted door closer handle special cylindrical lock, neoprene dry set ,rubber gasket, with 12m thick prelaminated (both side) particle board & 5mm thick plain glass complete all as specified and as directed.

Powder coated aluminium window side hung aluminium window/ ventilator frame or chowkats 1.5 mm thick aluminium anodized of size 65 mm x 40 mm and window shutter frames (sides rail, top rail, bottom rail and middle rail) 1.5 mm thick aluminium anodized of size 45 mm x 45 mm including all fitting such as rubber gasket aluminium glazing clips, locking arrangement and 75 mm aluminium handle and including 5mm thick tinted plain glass in panels fixed with rubber, gasket and aluminium beads, aluminium tower bolt 100 mm, aluminium butt hinges 75 mm 02 No in each shutter, complete all as specified and as directed. (Size of window shall be as sper site requirement.)

S&F powder coated aluminium window side hung aluminium window/ ventilator frame or chowkats 1.5 mm thick aluminium anodized of size 65 mm x 40 mm and window shutter frames (sides rail, top rail, bottom rail and middle rail) 1.5 mm thick aluminium anodized of size 45 mm x 45 mm including all fitting such as rubber gasket aluminium glazing clips, locking arrangement and 75 mm aluminium handle and including stainless wire cloth fixed with aluminium beads, aluminium tower bolt 100 mm, aluminium butt hinges 75 mm 02 No in each shutter, complete all as specified and as directed. (Size of window shall be as sper site requirement.)

Powder coated aluminium frame and grill for door, window,ventilators with one or more rebated incl jointing cleat for fixing etc complete all as specified and as directed.

Solid PVC door frame of size 50mm x 47mm made out of 5mm both side Prelam PVC sheet used instead of plain colour PVC Sheet and edge will be painted to match with prelam sheet. reinforced with M.S. Square tube, in opening complete all as specified and as directed.

Factory made solid panel PVC door shutter 28 to 30mm thick style ,with 2,4 or 6 raised flush panel design with 2mm thick Moulded prelam PVC sheet on the front face & 2mm Prelam PVC sheet on back face all as specified and as directed.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing with grade Fe 410-W (Gde- E- 250)quality- A complete all as specified and as directed.

18/19mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and as directed.

0.90 mm thick decorative choice of lamination type 1 of surface finish, colour and pattern as approved, fixed with aproved adhesive as per manufacturer's insturctions complete all as specified and directed.

Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern including all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete all as specified and as directed.

Vitreous China wash basin, white, table top, size 425 X 340 X 175mm excluding tap, chain, plug but including brackets, waste fitting 32mm dia ,brass chromimium plated for glazed ware sink, basin,with pedestal, long screwed shanks and fly nuts flange end bedded in red lead cement and other end fixed complete all as specified and as directed. Make :- Cat part No. CNS-WHT-903

10 ltr capacity PVC valveless, syphonic action type flushing cistern low level white with inlet, ball valve, float and handle including connetion to pipe but fixed in repair complete all as specified and directed.

PVC Waste pipe 32 mm bore with cup and washers "as in repair" complete all as specified and directed.

Aluminium tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodized, fixed with rawl plugs. complete all as specified in repairs. (ISI Marked)

Brass hat peg solid body 125mm to 175mm long as per sample in repairs complete all as specified.

Glass shelf with chromium plated guard rails as in repair complete all as specified and directed. Make : Cat Part No AQN -7771.

Corner glass shelf with chromium plated rails including brackets as in repair complete all as specified and directed. Make : Cat Part No : ACN 1173.

100mm Cast iron soil, waste and vent in any length withor without ears, with cement joints,laid in trenches or in floors complete all as specified and as directed.(ISI Marked).

75mm Cast iron soil, waste and vent in any length withor without ears, with cement joints,laid in trenches or in floors complete all as specified and as directed (ISI Marked).

50mm Cast iron soil, waste and vent in any length withor without ears, with cement joints,fixed to wall complete all as specified and as directed.

Salt glazed stone ware gully traps square or round mouthed, type P of size 150x150mm set and jointed to drain pipe with cement mortar (1:1) including demolition of old unserviceable gully traps complete all as specified and as directed. (ISI Marked).

Cast iron bends (any radius diminishing pieces or tapes (larger bore measured), 75mm bore fitted with oval access door fixed with rubber ring joints as in repairs complete all as specified and as directed.

Cast iron bends (any radius diminishing pieces or tapes (larger bore measured), 100mm bore fitted with oval access door fixed with rubber rings joints as in repairs complete all as specified and as directed.

75mm Cast iron floor traps with grating including jointing to waste pipe fixed concrete type B1 (1:2:4). complete all as specified and as directed.(ISI Marked)

Cast iron branch pieces, single/double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 100 bore, fitted with oval access door as in repairs complete all as specified and as directed.

Cast iron Reducer 100mm for connecting and fixing gas pipe on walls as in repairs complete all as specified and as directed.

Stack clamps out of 50mm x 5mm flat iron and 6mm dia round iron stays,including bolts and nuts and securing ends of stays to wall or roof 50mm bore of pipe complete all as specified and as directed.

50mm Cast iron cowls complete all as specified and as directed.

Stainless Steel drapery rod powdered coated including brackets and necessary fitting "as in repair" complete all as specified and directed by Engr-in-Charge.

125mm butt hinges, medium weight ,cold rolled mild steel complete all as specified and as directed.

100mm brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts of extruded section complete all as specified and directed. (ISI Marked)

75mm brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts of extruded section complete all as specified and directed. (ISI Marked)

100 mm brass handles, cast type polished bright complete all as specified and directed. (ISI Marked)

Aluminium body heavy duty double action floor spring suitable for glass shutter at both side rotable complete all as specified and directed.

Hasp and staple size 100 mm powder coated with hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Plain, aluminium sheeting 0.56 mm thick, Alloy 31000 H4 in ridges, hips, valley gutter, drip, construction joints and straight flashing (length and girth as fixed) in repair complete all as specified and directed.

Taking up or down 15mm bore steel tubing with connections for cleaning for refixing or removing to store yard complete all as specified .

Taking up or down 20mm bore steel tubing with connections for cleaning for refixing or removing to store yard complete all as specified .

15mm galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified.

20mm galvanised steel water tubing medium grade (ISI Marked) with all fittings and fixed complete to walls and or laid under floors etc complete all as specified.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 15mm complete all as specified.

Gun metal globe of gate valve with iron wheel head, screwed both ends of size 20mm complete all as specified.

Hand shower 105mm dia round shape single flow with air effect (ABS body & face plate chrome plated) with rubit cleaning system connected with 1m long flex tube complete all as specified and as directed. Make Cat Part No. HSH-1717.

15 mm bore bib cock, fancy type, chromium plated, cast copper alloy with wall flange, screwed for iron pipe or for brass ferrule complete all as specified. Make:- Cat Part No KUP-35037PM.

Bball valves high pressure 20mm bore of pipe of PTMT with epoxy coated 20mm- 210 gms complete all as specified and as directed.

Over head shower 100mm dia round shape multi flow (ABS Body chrome plated with grey face plate) with rubit cleaning system fixed to pipe or union of 15mm bore complete all as specified. Make:- Cat part No. OHS-1999.

Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 litres including all accessories, complete all as specified and as directed.

15mm bore angular stop cock with wall flange chromium plated complete all as specified and directed. Make:- Cat Part No KUP-35053PM.

Central hole Basin Mixer without Popup waste and 450 mm Long Braided Hoses, Make : Cat Part No. CON-167 KNB including necessary fittings complete all as specified and as directed.

Exposed wall mixture with provision only for overhead shower & hand shower with connecting legs & wall flages, Make : Cat Part No FLR-5215N including necessary fittings complete all as specified and as directed.

Health faucet (ABS Body) with 8mm dia, 1.2 meter long flexible tube & wall hook with all accessories all as approved and fixed as in repairs complete all as specified and as directed. Make : ALD-587.

Soap dish cromium plated fixed with brass screws and wooden/ plastic cleats complete all as specified and as directed.

PVC connection 15mm bore with PTMT nuts of length 450mm complete all as specified and as directed.

Towel ring round with round flange as in repair complete all as specified and as directed. Make : Cat Part No : ACN-1121N.

Toilet paper holder as in repair complete all as specified and directed. Make : Cat Part No : ACN-1153S.

100mm thick plain cement concrete 1:4:8 type D2 (Using 40mm graded crushed stone aggregate) complete all as specified and as directed.

20 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified and as directed.

Cement concrete rich colored chequered tiles machine pressed with imported pigment smooth finish of size (300 mm x 300 mm or any size as approved and 20 to 25 mm) thick set and jointed with neat cement slurry complete all as specified and directed.

Providing cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneelers apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles 1:2:4 mix type B-0 complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n.exc 1.5 m in depth; for foundation, & n exc 10 Sqm on plan and n exc 1.5 m in depth and getting out in hard /dense soil, complete all as specified and as directed.

Brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4 complete all as specified and as directed.

Returning, filling including spreading leveling watering and well ramming in layers not exceeding 25mm in any type of soil complete all as specified and as directed.

Removing excavated material (soils) exceeding 250 m but n.exc. 500m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement motor 1:4 and finished even and smooth without using extra cement complete all as specified

Cement concrete 1:3:6 type C1 (Using 20mm graded crushed stone aggregate) as in surface channels and drains including necessary formwork etc all as specified.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms moulds, mitered/stopped ends etc complete all as specified and as directed.

150 mm bore Salt-glazed stoneware drain pipes laid in trenches and jointed complete all as specified and as directed.

Cement concrete 1:4:8 type D2 (using 40mm graded crushed stone aggregate) in bed to 150 mm dia pipes including packing under, and haunching against the sides of pipes after they are laid and tested for complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel of 150mm internal dia of pipe (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete all as specified and as directed.

Providing Precast cement concrete 1:2:4 type B-1 (Using 20mm graded crushed stone aggregate) as in manholes cover slab etc complete all as specified and as directed.

Providing cement concrete 1:2:4 type B-0 in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneelers apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles complete all as specified and directed.

Mild Steel TMT bars 6mm to 8mm dia cut to length bent to shape required including cranking bending spirally for hooping ends and binding with and including mild steel wire ( annealed ) not less than 0.90 mm dia or securing with clips .

Brick work with sub class B bricks straight or curved on plan to any radius built in CM 1:4 but except bricks all complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified.

Providing cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneelers apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 Mix type B-0 complete all as specified and as directed.

PCC 1: 2 : 4 type B-2 using 20 mm graded aggregate in surafce channel and drains complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard /dense soil complete all as specified and as directed.

Reinforced cement concrete M-25 (Using 20mm graded crushed stone aggregates) design mix as in foundations, including rafts, footings, foundation, beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

Reinforced cement concrete M-25 (Using 20mm graded crushed stone aggregates) design mix columns, pillars, piers,posts and struts complete all as specified and as directed.

Reinforced cement concrete M-25 (Using 20mm graded crushed stone aggregates) design mix as in beams, cantilevers,bressummers, lintels over 1.5m span complete all as specified and as directed.

Reinforced cement concrete M-25 (Using 20mm graded crushed stone aggregates) design mix as in slabs supported on walls, beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Reinforced cement concrete M-25 (Using 20mm graded crushed stone aggregates) design mix as in chajjas complete all as specified and as directed.

Reinforced cement concrete M-25 (Using 20mm graded crushed stone aggregates) design mix as in chullah hoods; stairways (except spiral staircases) including steps (square or spandril), string pieces, carriages, etc., complete, any section straight or winding, but excluding landings; RCC water tanks upto 1500 litres complete all as specified and as directed.

Reinforced cement concrete M-25 (Using 20mm graded crushed stone aggregates) design mix as in Fins, fascias, louvers, parapets, and railings exc. 60cm in height, newels, baluster, and the like complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter for rough flat finished surfaces of concrete, complete all as specified and as directed.

Formwork to sides of pillars,posts, struts, piers, columns and stanchions for rough flat finished surface of concrete, complete all as specified and as directed.

Formwork to flat sides and soffits of or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, complete all as specified and as directed.

Formwork to soffits of suspended flat slabs such as roof slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Formwork to edges of concrete flats, treads breaks in floors, window cills, concrete railings,openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in wall, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and as directed.

Formwork to chullah hoods, chajjas,troughs and similar items including edges for rough flat finished surface of concrete, complete all as specified and as directed.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and as directed.

Mild Steel TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

All as per srl item No 141 above but 5mm dia and over including 10mm dia in stirrups, spaces and binders etc complete all as specified and as directed.

Rendering 10 mm thick on fair faces of brick /concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed.

Supply only Liquid water proofing compound complete all as specified and as directed.

Rendering 05 mm thick in CM 1:4 on fair surfaces of ceiling work and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 10 mm thick as backing coat to receive the tiles on fair faces of brick /concrete surfaces in cement mortar 1:3 and finished even and rough complete all as specified and as directed.

Preparation of new plastered surfaces of walls and applying three coats of white wash.complete all as specified and directed.

Two coat of Oil bound distemper including a coat of primer including preparation of newly plastered surfaces of wall complete all as specified and as directed.

Preparation of new plastered surfaces on ceiling and applying three coats of white wash.complete all as specified and directed.

Preparation of new plastered surfaces on walls and applying two coats of cement based paint over a coat of alkali resistant priming paint complete all as specified and directed.

Preparation of new plastered surfaces and applying two coats of apex ultima paint over a coat of primer including preparation of surfaces complete all as specified and as directed. (colour of apex ultima approved by GE).

Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

75 mm thick cement concrete (1:4:8) type D2 as sub base to floor complete all as specified and as directed.

25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete all as specified and as directed.

10mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and as directed.

Non-skid coloured ceramic tiles (square/rectangular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface, complete all as specified and as directed.

Glazed ceramic tiles in vertical surface 300 x 450 x 7, 600 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed.

Screed bed or bedding layer of mortar 20mm thick in cement mortar 1:6 laying floor finishes complete all as specified and as directed.

Machine cut kota stone slab flooring 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Machine cut kota stone slab flooring 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

150mm wide strip of makrana white marble 20 mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types complete all as specified and as directed.

M&L for 50 mm thick cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (n exc 2 sqm each) area with 6mm wide joints and 10mm wide joints between the walls and plinth protection, finished even and smooth without using extra cement, outward slope of not less than 1:12, the joints shall be filled with mastic filling comprising one coat of bitumen 85/25 grade and three parts of sand by weight, complete all as specified and as directed.

S&F steel window (box type) with gauzed shutter factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and as directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge,Glass shall be measured and paid separately.

Description all as per Srl Item No 163 but without glazing bar complete all as specified and as directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Mild Steel ventilators (Box type) factory made with top hung shutters and bottom fixed type shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dove tailed or welded including one shop coat of red oxide primer complete all as specified. Note : (i) The window shall be fabricated as per Drg CEUZ/TD/1269/2008 Sh 1/3 (ii) Glazing, wire gauge shall be measured and paid separately.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 quality A including one shop coat of zinc chromate primer paint including preparation of surfaces at contractor's workshop before fabrication complete all as specified and as directed.

Welded steel wire fabric mesh weight n.exc 4 Kgs per sqm fixed to steel members complete all as specified and as directed.

4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

4 mm thick glass sheet of frosted ordinary quality n exc 0.5 Sqm in each pane complete all as specified and as directed.

Preparation of newly steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick(stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, complete all as specified and as directed.

Pressed steel frames for doors made out of 1.25mm thick MS sheet with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate 12mm bar thresh hold etc. complete , of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and as directed.

Pressed steel frames size 105x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. fixed as in repair complete all as specified and as directed.

Factory made, 2nd class hard wood 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

Factory made, 2nd class hard wood 35 mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauze etc complete all as specified and as directed.

Aluminum handles cast type, anodised, 150 mm size complete all as specified and as directed.

Aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified and as directed.

Mild Steel cold rolled butt hinges medium weight 100 mm long complete all as specified and as directed.

Rendering 10 mm thick in CM 1:3 on roof sufaces, finished even and smooth without using extra cement complete all as specified and as directed. Note :- Supply only water proofing compound shall be measured and paid seperately under the respective item.

Applying bituminous primer on roof surfaces @ 0.40 liters/Sqm and applying one coat of semi hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and thereafter supply and laying 3mm thick polymeric water proofing membrane, five layered, of weight not less than 3 Kg per Sqm with centre layer core of 90 micron high molecular density polyethylene film and bonded completely to the surface with overlap of 10 cms (overlaps to be thermo fused by flame) followed by another coat of semi hot blown bitumen 85/25 grade bitumen @ 0.70 Kg/Sqm and provide aluminium paint as per Manufacturer's instructions complete all as specified and as directed. Note:- Water proofing treatment will be done or through a approved specialized agancy.

Cement concrete tiles 30cm x 30cm x 20mm thick with grey cement and pigment, machine pressed; set jointed and pointed in neat cement slurry in floors, cut and polished over roof treatment complete all as specified and as directed.

Steel water tubing of nominal bore dia 15 mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and as directed.

Steel water tubing of nominal bore dia 20 mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and as directed.

20mm dia, Ball brass, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and as directed.

20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

1000 ltrs capacity Rotational moulded polythylene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in relevant SSR.

Vireous china urinals half stall white including CP urinal Spray Nozzal complete including providing and fixing of plug bedding urinal against wall in cement motar 1:2 securing urinal to plug with and including 60mm long brass screws pointing including 60mm long brass complete all as specified and as directed.

Water closet (Orissa pattern) with P or S trap including lime concrete bedding, vitreous china long pan orissa pattern 580x440mm, white with integral foot rests (excluding flushing cistern & flush pipe) fixed in repairs complete all as specified and as directed.

PVC waste pipe 32 mm bore with cup and washers complete all as specified and as directed.

Waste coupling chromium plated 32 mm bore size full threaded with 80 mm height including all necessry washers "as in repair" complete all as specified and as directed.

10 litres Vitreous China valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

Supply Only Flush pipe of polyethylene of low or high density or PVC, 32 mm dia, for low level cistern complete all as specified and as directed.

PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and as directed.

Angle valve, cast copper alloy fancy type screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified and as directed.

Stop valve (concealed type), cast copper alloy fancy type, chromium plated with long shank and cup screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified and as directed.

15 mm dia bib tap fancy type chomium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and as directed.

Vitreous China wash basin (Pedestal), white, flat back, size 550 mm x 400 mm excluding tap, chain, plug and porcelain stopper but including brackets and cutting for and pinning in ends of brackets complete all as specified and as directed.

Pillar taps 15mm bore fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' and cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

Aluminium anodised plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and as directed.

Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

Glass shelf with chromium plated guard rails as in repair complete all as specified and directed. Make : Cat Part No AQN -7771.

Corner glass shelf with chromium plated rails incl brackets as in repair complete all as specified and directed. Make : Cat Part No : ACN 1173.

100mm dia cast iron sanitary connection pipe upto 300mm length complete all as specified and as directed.

Cast iron soil, waste and vent pipes (sand cast) 100mm bore in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and as directed.

Cast iron soil, waste and vent pipes (sand cast) 75mm bore in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and as directed.

100mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed.

Cast iron soil, waste and vent pipes (sand cast) 50mm bore in any length with or without ears with cement joints fixed to wall complete all as specified and as directed.

Cast iron bend (any radius) diminishing pieces or tapers 100mm bore fitted with oval access door complete all as specified and as directed.

Cast iron bend (any radius) diminishing pieces or tapers 75mm bore fitted with oval access door complete all as specified and as directed.

50mm bore Cast iron cowls complete all as specified and as directed.

Cast iron floor trap 75 mm, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

Stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 50 mm bore complete all as specified and as directed.

Shower rose 15 mm chromium plated with or without swivel joints, any size, including 125 mm long arm and fixing to steel pipe or union, complete all as specified and as directed.

M&L for along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. In apron compelte all as specified and as directed.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse Sand) to match the existing floor, complete all as specified and as directed.

Surface dressing n exc15 cm deep in hard/ dense soil complete all as specified and as directed.

Excavation in post holes (or similar holes) in any type of soil, each not exc 0.50 cum, getting out, removing surplus spoil to distance not exceeding 50 mtr and making good surface complete all as specified and as directed.

Mild steel work conforming to Fe 410-O or Fe 310-O as in posts and struts etc in fencing including cutting tops to shape as directed drilling holes , notching for wire etc including necessary riveting and/or necessary welding where required and fixing with screws, bolts etc complete all as specified and as directed.

Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt not exceeding 5 cm and dia of shank 5 to 10 mm complete all as specified and as directed.

Supply only mild steel galvanised chain link fencing of size 10 cm mesh made of 4.6 mm dia galvanised plain wire complete all as specified and as directed.

Fixing only chain link fencing including line wire, any mesh, size and type to any type of standard rails, straining bots etc including provision of binding wire complete all as specified and as directed.

Supply only mild steel round bars 10 mm dia conforming to Fe-290 (Gde E-165) for securing chain link fencing

Supply only mild steel flat 50 x 6 mm conforming to Fe 410-O or Fe 310-O for securing chain link fencing

Galvanised 2 strand, steel barbed wire 2.24 mm dia, barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to mild steel fencing posts, any type of standard rails, straining bolts including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel nibs, pins etc all as specified and as directed (each line wire shall be measured independently)

Plain mild steel wire 3.15 mm dia, galvanized class 3 in fencing including straining and fixing to steel posts including securing with and provision of galvanized iron typing wire, galvanized iron staples or steel pins etc complete all as specified and as directed.

Preparation of new steel surfaces of any description, over 10 cm in width or girth and applying two coats of black bituminous paint complete all as specified and as directed.

M&L for two coats of white wash on wall including preparation of surface complete all as specified and directed.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as directed.

Point wiring for one light/ fan/bell/ Exh/fan point controlled by one switch using 1.5 Sq mm FRLS copper conductor cables (multistranded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5mm and 20mm dia), medium grade with Modular metal flush boxes thickness (1.25mm) & PVC back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts copper conductor cable 1.5Sq mm as earth wire stranded and conected to earth dolly all as specified.

All as per srl item No 231 but for 3 pin 10 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per srl item No 231 but for 3 pin 10 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per Srl item No 231 but for 3 Pin 20 Amps socket outlet independent with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

All as per Srl item No 231 but for 3 Pin 20 Amps socket outlet independent with cable 4.0 Sq mm including copper PVC insulated PVC unsheathed 2.5 sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

Switch Piano flush type 10 Amps single pole one way (Modular Type) with outer strip complete all as specified and as directed.

Switch Piano flush type 20 Amps single pole one way (Modular Type) with outer strip complete all as specified and as directed.

Socket combined 2-in-1, 3 Pin 10 Amps (Modular Type) with outer strip complete all as specified and as directed.

Socket combined 2-in-1, 3 Pin 10 & 20 Amps (Modular Type) with outer strip complete all as specified and as directed.

Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Block complete all as specified and as directed.

Call bell ding-dong 230 volts including taking down old one complete all as specified and as directed.

Bell push, flush type, 10 Amp, complete all as specified and as directed.

Single pole and neutral enclosure surface mounted 240 voltswith 2 pin and earth plug and socket with one single pole MCB 20 Amps with indicator complete all as specified and as directed.

Regulator electronic, stepped type hum free suitable control speed of fan from 0 to 100 % and connecting electrically complete all as specified and as directed.

S&F in replacement MCB Single Pole, 230 Volt, rating 6 to 40 Amps complete all as specified and as directed.

S&F in replacement MCB Single Pole and Neutral , 230 Volt, rating 40 to 63 Amps complete all as specified and as directed.

S & F in replacement sheet metal enclosures for DBs when MCBs to be used double door DB VTPN MCCB 125A 4 way IP43 Protection complete all as specified and as directed. Make: Cat Pt No - 811888 with 125A MCCB 16kA or Cat Pt No - 830153.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed. (Note-MCBs will be measured separately)

Venza decorative wall mounting light fitting, SS finish fixture with opal glass diffuser including 12W retrofit LED bulb and making all connection using flexible cable of suitable size from ceiling rose to fitting including taking down existing light complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Supply and fixing electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Supply and fixing exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers Note: Unserviceable Items deposited in MES store in BER procedure complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 06 Sq mm as earth lead including taking down old sub main wiring complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 06 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 4 Sq mm as earth lead including taking down old sub main wiring complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electode 600mm x 600mm x 6.00mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including galvanised steel earth lead wire 4 mm dia by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-1 angle iron frame with RCC cover and handle, excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mash and light grade GI protection pipe 15mm bore upto main board complete all as shown in electrical plate No 3 of relevant MES SSR connected to main control board as specified and testing completion.

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 25 Sqmm x 4 core size including taking down old cable complete all as specified and as directed. Note : Earth work and other connected work shall be measured & paid sperately.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and as directed. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels all as specified.

Supply and fixing GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and as directed.

Point wiring for one light point controlled by one way switch using 1.5 Sq mm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5mm and 20mm dia), medium grade with sunk Cl / Pressed steel terminal boxes with 3mm thick laminated sheet cover including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire stranded and conected to earth dolly complete all as specified and as directed.

All as per srl item No 263 but for ceiling fan/ Exhaust fan point

All as per srl item No 263 but for 3 pin 5 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly.

All as per srl item No 263 but for 3 pin 5 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly.

All as per Srl item No 263 but for 3 Pin 15 Amps socket outlet independent with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 2.5 sq mm earth wire standard and connected to earth dolly.

All as per Srl item No 263 but for 3 Pin 15 Amps socket outlet independent with cable 4.0 Sq mm including copper PVC insulated PVC unsheathed 4.0 sq mm earth wire standard and connected to earth dolly.

Switch piano flush type 5 Amps single pole one way complete all as specified and as directed.

Socket 3 Pin 6 Amps flush type complete all as specified and as directed.

Switch socket combination 2-in-3 pin 5 Amps flush type complete all as specified and as directed.

Switch socket combination 2-in-1, 3 pin 5 & 15 Amps flush type complete all as specified and as directed.

Sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20A 240 complete with one single pole MCB of any cap from 10 to 20 A complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 1 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc complete all as specified and as directed.

Supply and fixing LED flood light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant including bracket with driver and lamp complete all as specified and as directed.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 8 way with double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing surface complete all as specified and directed.(Note-MCBs will be measured separately)

MCB Single Pole 5 to to 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

MCB Single Pole & Neutral 40 to 63 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 16 Sqmm x 2 core size including taking down old cable MCB Single Pole & Neutral. Note : Earth work and other connected work shall be measured & paid sperately.

s l sharma and sons

HIMALAYA ENTERPRISES

VIRINDER SINGH

R K BUILDERS

RAMAN CONSTRUCTION CO

SINGH CONST CO