Sanitary Fitting and other allied works for the Construction of 15 Nos Class Room School Building at Govt. Boys Hr. Sec. School Akhnoor

Amount

Providing and fixing water closet squatting pan ( Indian type W.C. pan) with 100 mm sand cast Iron P or Strap, 10 litre low level P.V. C. flushing cistern including flush pipe (of approved make) "manually contro(led device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. Orissa pattern white vitreous china W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C . .pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied: W.C. pan with lSI marked white solid plastic seat and lid.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x41 Ox265 mm sizes respectively with automatic flushing cistern with C. I./M.S. brackets standard size of G. I. flush pipe and C.P. brass spreaders with brass unions and G. I. clamps complete, including painting of fittings Range of two urinal basins with 5 litre P.V.C white automatic flushing cistern of approved quality. and brackets, cutting and making good the wafls and floors wherever required:

Providing and fixing wash basin with C. I./M.S. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China wash basin size 550x400 mm with single 15 mm C.P. brass pillar taps

Providing and fixing P.V.C Waste pipe for sink or wash basin including P.V.C waste fittings complete. Semi rigid pipe 32mm dia

Providing and fixing 100 mm sand cast iron grating for gully, floor or Nahani trap

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing and fixing mirror of superior glass( of approved quality) and of required shape and size with plastic . moulded frame of approved make and shade with 6 mm thick hard board backing

Oval shape 450x350mm (outer dimensions)

Rectangular shape 1500x450 mm

Providing and fixing toilet paper holder C.P. brass

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour Waste coupling 38mm of 83 mm length and 77 mm breadth weighing not less than 60gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour: 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.

Providing and fixing G.l. pipes complete with G.l. fittings and clamps, including cutting and making good the walls etc.:

15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

Providing and fixing gun metal gate valve with C.l. wheel of approved quality (screwed end) 25 mm nominal bore

Providing and fixing ball valve (brass) of approved quality complete High or low pressure with plastic floats

15 mm nominal bore

20 mm nominal bore

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) R.C.C. top slab with 1 :2:4 mix ( 1 cemE?nt : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finsihed with a floating coat of neat cement complete as per standard design. Inside size 90x80 em and 45 em deep including C.l. cover with frame (light duty) 455x610mm. internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) With F.P.S. bricks with class designation 75 & with Crushed stone aggregate including all leads lifts and carriage complete Job.

Providing and fixing G.l. Union in G.l. pipe including cutting and threading the pipe and making long screws etc. complete (new work)

15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license].

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and gyser points _of approved make conforming to IS : 8931 15 mm nominal bore

Cutting holes up to 15x15 em in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 gradedstone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Providing and fixing uPVC single socketed pipes, including collars etc. working pressuer of 4 Kg/Sqm) of approved make like supreme, fenolex Prince or equivalent in proper line/alignment/gradient including jointing etc. complete with recommended Adhesive colour seal ring

75mm dia

110mm dia

150mm dia

Making soak pit 5.00 Mtr. dia and 5.00 Mtr. deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W drain pipe 100mm diameter, 1.8 Mtr. long complete as per standard design including all leads lifts and carriage complete Job.

Providing and fixing uPVC fittings and acessories etc. complete with Adhesives Coupler

75mm dia

110mm dia

150mm dia

Providing and fixing uPVC fittings and acessories etc. complete with Adhesives Single equal tee without door

Providing and fixing uPVC fittings and acessories etc. complete with Adhesives Single equal tee with door

Providing and fixing uPVC fittings and acessories etc. complete with Adhesives Bend 87.5 degree

75mm dia

110mm dia

150mm dia

Providing and fixing uPVC fittings and acessories etc. complete with Adhesives Plain Shoe

75mm dia

110mm dia

150mm dia

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc.including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete,i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .. gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- Charge (glazing, panelling and dash fasteners to be paid for separately.) For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber I neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.) With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg I sqm)

Providing and fixing 12mm thick prelaminated particle boardflat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-l type-11) in panelling fixed in aluminium doors, windows shutters and partition frames with C. P. brass I stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Providing and fixing aluminium tower bolts lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete

Providing and fixing aluminium handles lSI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 100 mm

Providing and fixing 100mm brass locks (best make of approved quality)for aluminium doors including necessary cutting and making good etc complete

Providing and fixing of one HP Motor (boosting pump) of Kirloskar, sharp or equivalent make with necessary fittings etc. complete

Radha Krishan

Rakesh Kumar

Romesh Chander