GE/PNH-03/2024-25

Amount

B/R PORTION: Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out and getting out in any type of soil complete all as specified.

Excavation over area not exc 1.5 in depth and getting out in any type of soil, complete all as specified.

Excavation in trenches n.exc 1.50m wide and n.exc 1.50m in depth for foundation etc. and getting out in any type of soil, complete all as specified.

Removal of excavated materials not exc 50cm and depositing where directed at a level n.exc 1.5m above the starting point complete, all as specified and directed.

Returning and filling incl spreading leveling watering and well ramming in layers n.exc 25 cm in soft/loose soil complete, all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in foundation of poles/stays & mass concrete complete all as specified directed.

RCC M-25 (design mix) using 20mm graded crushed stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases of columns etc. complete all as specified and directed by Engineer-in-Charge.

M&L for RCC M-25(design mix) using 20mm graded crushed stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M&L for RCC M-25(design mix) using 20mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for RCC Design mix M-25using 20mm grade aggregates in beams in chajjas, complete all as specified and directed

M&L for RCC M-25(design mix) using 20mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed

M&L for brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified.

M&L for brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified.

Form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to better with rough finished surfaces of concrete complete all as specified & directed

Form work to sides and soffits of floor or roof beams, girders, bressummers,lintels etc for rough finished surface of concrete complete all as specified & directed by Engineer-in- charge.

Form work to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for rough finished surfaces of concrete, complete all as specified and directed.

Form work to sides of pillars, posts, struts piers, columns and stanchions and similar works fair finished surface of concrete complete all as specified & directed by Engineer-in- charge.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide rough finished surfaces of concrete complete all as specified

Formwork to chullah hoods, chajjas, troughs and similar items in cluding edges, complete all as specified and directed

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required incl cranking, bending, spirally for hooking for column, hooking ends and binding with MS wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to FS-410 all as specified.

S&F mild steel TMT bars 5 mm dia and over cut to length, bent to shape required incl cranking, bending, spirally, hooking for column, hooking ends and binding with MS wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to FS-410 all as specified.

M&L for rendering 15mm thick in cement mortar (1:4) on fair faces of the brick work or cement concrete surfaces, finishing the surface even and smooth without using extra cement, complete all as specified

M&L for rendering 10mm thick in cement mortar (1:6) on fair faces of the brick work or cement concrete surfaces, finishing the surface even and smooth without using extra cement, complete all as specified

M&L for rendering 5mm thick in cement mortar (1:3) on ceiling surfaces, finishing the surface even and smooth without using extra cement, complete all as specified

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

Supply and fixing factory made solid core PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC sheet, 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified & shown in relevant drawing of item No. 08080 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

Supply and fixing Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 100 mm Butt hinges, medium weight, cold rolled mild steel, and fixed, complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

S&F Aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S&F Sheet glass, ordinary quality, 3 mm thick and glazing with oil putty or wooden beads, in square n exc. 0.5 Sqm pane, complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11sqm but not exceeding 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over and including 15mm thick screed bed in CM (1:6) , complete all as specified.

M&L for glazed ceramic coloured tiles 450x350mm x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base to flooring/path etc, complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in flooring/path etc, complete all as specified.

M&L for Plain cement Concrete 1:2:4 type-B1 (using 20mm graded crushed stone aggregate) as in copings, hold fasts plinth band, bed blocks and like slightly rounded or chamfered angles as directed including necessary form work,complete all as specified.

S&F Vitreous china Wash hand basin, white, flat back of size 580x450mm including brackets, brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc, complete all as specified.

S&F 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe complete, all as specified & directed.

S&F Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete, all as specified & directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified & directed.

S&F Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified.

S&F Steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified.

S&F Bib tap 15mm bore of cast copper alloy chromium plated fancy type, screwed down, high presure with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule, fixed, complete all as specified and directed.

S&F 15mm bore Stop valve cast copper alloy chromium plated fancy type screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, complete all as specified.

S&F 15mm bore Stop valve cast copper alloy chromium plated fancy type with long shank and cup (concealed type) screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, fixed in repairs, complete all as specified.

S&F 20mm bore Stop valve cast copper alloy chromium plated fancy type screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, complete all as specified.

S&F chromium plated shower rose 125 mm size with or without swivel joints of any size, incl fixing to pipe or union, with & incl 15 mm bore, 195 mm long shower arm with bend of 45 degree with flange of PTMT (min wt 40 gms) complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts on both ends of length 600mm, complete all as specified.

M&L for PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint, laid in floor/walls/trenches as soil pipe, fixed, complete all as specified and directed.

M&L for PVC (SWR) pipes 110 mm dia any length single socketed with rubber ring joint, laid in floor/walls/trenches as soil pipe, fixed, complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm bore, complete all as specified.

S&F PVC (SWR) bends any radius 110mm bore, with ovel access door complete all as specified.

S&F PVC (SWR) gully trap of 125/100mm, setting & jointing with solvent cement fixed, complete all as specified.

S&F PVC (SWR) 110 mm size, branch piece, double (double Y) equal or unequal, complete all as specified.

S&F PVC bends any radius 75mm bore, diminishing pieces or tapers (larger bore measured), complete all as specified.

S&F PVC (SWR) branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, complete all as specified.

S&F PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing to waste pipe with solvent cement fixed, complete all as specified.

S&F 20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified.

S&F PVC valve less syphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets with and incl including 32mm dia PVC flush pipe for low level cistern including all joints, complete all as specified.

S&F vitreous china bowl urinal flat back, size of 465x355x265mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws and pointing around urinal back in cement etc and 32mm dia PVC waste pipe fixed, complete all as specified and directed.

S&F Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, with integral foot rests and incl 'P' or 'S' trap complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc, complete, all as specified.

S&F PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing to waste pipe with solvent cement fixed, complete all as specified.

S&F 500 ltr capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) and fixed in position, all as specified in SSR Part-I incl Ball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule, 20mm bore, valvecomplete all as specified and directed.

S&F 1000 ltr capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) and fixed in position, all as specified in SSR Part-I incl Ball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule, 20mm bore, valvecomplete all as specified and directed.

M&L for preparation of newly plastered / unplastered surfaces of wall including cornices pilaster etc, and applying two coats of cement base paint over a coat of white wash complete all as specified and directed.

M&L for preparation of new plastered / unplastered surface of wall including cornices pilaster etc, and applying two coats of oil bound distemper over and including 1 mm thick wall care putty, complete all as specified and directed.

M & L for two coats of oil bound distemper on ceiling incl preparation newly plastered surface complete all as specified.

M&L for Moorum/red bajri filling in floors or paving, laid in layers n exc. 15 cm thick, spread, leveled and rammed including watering, complete all as specified and directed.

M&L for hard core, filling under floor, breaking stone or boulder exc 63mm and n.exc 100mm gauge of sand stone complete all as specified and directed.

Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for 10mm thick rendering on roof surfaces, before laying of APP, complete, all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified and directed.

M&L for priming surfaces and applying normal treatment (for moderate conditions) using glass fibre base bitumen felt, grade 2, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 Type C-2 (using 40mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

S&F Steel windows or ventilators, fixed type with glazing bars, complete, all as specified and directed.

S&F PVC (SWR) vent cowl 110mm dia, complete all as specified and directed.

S&F 32 mm bore PVC waste pipe, complete all as specified.

S&F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete all as specified.

S&F Soap dish, any type, fixed to plugs with chromium plated brass screws, complete all as specified and directed.

S&F Tubular towel rail 60mm long 20mm dia aluminium anodised incl necessary brackets, fixed, complete all as specified and directed.

S&F 150 mm bore salt glazed stone ware drain pipes, grade ‘A’ laid in trenches and jointed in cement mortar complete all as specified and all as directed by Engr-in-Charge.

M&L for Concrete bed to drain pipes including packing under and haunching against the sides of pipes for 150mm SGSW pipe after they are laid in PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

M&L for Precast cement concrete (1:2:4) using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc), chullah hoods, chajjas, water troughs, shelves and similar articles with plain fair faces including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for chequered cement concrete tiles 300x300x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment laid over and including 20mm thick screed bed in CM 1:4, complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement complete all as specified.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide rough finished surfaces of concrete complete all as specified

M&L for rendering 15mm thick in cement mortar (1:4) on fair faces of the brick work or cement concrete surfaces, finishing the surface even and smooth without using extra cement with mixing of WPC @ 200 ml/kg of cement, complete all as specified and directed.

Supply only Integral water proofing compound, ISI marked, complete all as specified and directed.

S&F Steel water tubing of 25 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified.

S&F 25mm bore gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, complete all as specified.

Cutting existing steel tubing for alteration or addition including screwing existing steel tubing to form connection/branch pipe etc for 40mm bore pipes complete all as specified.

M&L for on site conventional type LLDPE septic tank with upflow filter for 10 user incl media designed to carry sewage and sullage water, incl excation in amy type of soil, PCC 1:4:8 below foundation, vent shadt, connection etc complete all as specified and directed by Engr-in-Charge.

M&L for on site conventional type LLDPE septic tank with upflow filter for 25 user incl media designed to carry sewage and sullage water, incl excation in amy type of soil, PCC 1:4:8 below foundation, vent shadt, connection etc complete all as specified and directed by Engr-in-Charge.

M&L for construction of brick masonry valve pit of size 60x60x90 cm (internal dimension of chamber incl internal plastering and flash pointing externally) complete with MS sheet cover, handle, packing arrangement, earth work in any type of soil incl removal to a distance not exc 50 mtr and painting with two coats of synthetic enamel paint over a coat of red oxide primer to steel surfaces complete all as specified and directed by Enge-in-charge.

M&L for Soakage Well 1.2m dia X 3.1 m effective depth with foundation in PCC 1:3:6 walls of honeycombed masonary with top ring of M25 concrete bedding including intercepting chamber and screen chamber made of brick masonary in CM 1:4, RCC cover slab M25/ SFRC cover interconneting pipes of RCC/ DWC complete all as shown in drawing No. CE/TD-1585/2021 sheet 1/4 to 4/4 and as specified and directed.

E&M PORTION:- M&L for point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light/fan point controlled by one way switch 6 Amp complete all as specified and directed.

One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed.

One 3/5 pin socket outlet 6 amp on independent board complete all as specified and directed.

All as per srl item No 99 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 2.5 Sqmm as in continuous earth wire complete all as specified and directed.

S&F ceiling rose, 3 terminal, surface bakelite 65 mm x 50mm, PVC/poly carbonate, insulated body, complete all as specified and directed.

S&F switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin, 6 amps, flush type, complete all as specified and directed.

S&F switch socket combination 2 in 1, 3 pin, 6 and 16 Amp flush type universal, complete all as specified and directed.

Supply and fix Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

Supply and fixing inverter LED batten 1x 20W, with square profile and polycarbonate channel, lithium iron battery with charging time of 8 to 10 hours and backup tile upto 04 hours with driver, holder incl LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make : Havells cat part No. LHEXACP7FN1W020 or equivalent make as specified in PS

S&F in repair LED inverter lamp CDL 10 watt with holder base (B22) type, complete all as specified and directed. Make of LED lamp:- Havells cat part No LHLDDDBAIA2R010 or Equivalent cat part of make as specified in Appx 'A' to P.S.

Supply and fixing LED street light fitting with individuual high power LEDs with capacity 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing with toughned glass and heat resistant complete with driver, lamp bracket with impact resistance of IK 07 and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete with and incl 40 mm dia bracket, angle with fixing material , complete all as specified and directed.

S&F sheet metal enclosure for DBs, SPN double door (IP43), 8 ways with 200 amps rated bus bar suitable for 240 volts, AC, 50 Hz, connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed.

S&F MCB SPN 40 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCSNF040 - DHMGCSNF063 or Equivalent cat part of make as specified in P.S.

S&F MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series complete all as specified and directed. Make:-Havells cat part No-DHMGCSPF006-032 or Equivalent cat part of make as specified in P.S.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 380mm sweep with, blades, and frame and louvers, complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250m, complete all as specified and directed.

Supply and fixing electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc., complete all as specified and directed.

Supply and fixing plug & socket DB, CRCA steel sheet, powder coated with metal plug & socket 3 pin and earth plug and socket complete with and incl one single pole MCB, complete all as specified and directed.

Supply and laying in trenches or passing through pipe/walls 1100 volts grade armoured, heavy duty XLPE electric cable with aluminium conductor of size 10 Sqmm 2 core including taking down old/ unsv cable any type complete all as specified and directed.

Supply and laying sand river for cushioning with layers of 8 cm before laying of cable and 15 cm after laying of cable (23 cm after punning down), complete all as specified and directed. Note: Punned down thickness shall be measured

M&L for Sub class 'B' bricks laid dry flat transversely along the length of cable with width equal to the length of brick over sand cushioning as protection cover of cable laid in trenches, complete all as specified

S&F Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing, complete all as specified and directed.

M/S FAIZ AHMED KHAN

JAMWAL CONSTRUCTION CO

M/S KHAN ENTERPRISES