PROVISION OF COVERED SHED FOR STORAGE OF NITROGEN AND OXYGEN CYLINDER AT BSF GOA ADDN ALTN CERTAIN ROOMS IN H3 HANGER P673 INAS 303 PROVISION OF AIR CONDITIONER FOR PRECISION APPROCH RADAR ROOM IN BLDG P29 INS HANSA AGE BR I AGE EM I OF GE NW VASCO

Amount

PROVISION OF COVERED SHED FOR STORAGE OF NITROGEN AND OXYGEN CYLINDER AT BSF (GOA) AT INS HANSA UNDER AGE B/R - I AND AGE E/M - I OF GE (NW) VASCO.

Surface Excavation not exceeding 30 Cm deep and averaging 15 Cm deep and getting out in Soft/disintegrated rock

Removing Excavated soils not exc 50 M and depositing where directed at a level not exc1.5 M above the starting point.

M & L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled layers not exceeding 15 cm thick, watered and rammed to a true surface.

M & L 100 mm thick Cement concrete type B-1, 1:2:4 (using 20 mm graded stone aggregate) in flooring/ hardstanding and finishing cement concrete surface even and smooth without using extra cement

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified

Excavating post holes or similar holes, each not exceeding 0.5 Cu. M, getting out in Soft/ disintegrated soil and removing surplus soil to a distance n.exc 50m & making good surface

Plain Cement Concrete Type C2 1:3:6 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete.

S & F Mild steel roof trusses (framed), Trussesd, purlins, crane grantries, rails and framings and heavy bracket framing (Beam, tee, angle, channel or flat sections) confrming to Fe 410-W including cleats, distance pieces etc

Preparation of new steel surfaces and applying two coats of epoxy anti corrossive paint over a coat of zinc primer

Pre - cast cement concrete 1:3:6 type C-1, (20mm graded stone aggregate) block masonary with solid blocks built in cement mortar 1:6

M&L for rendering 15 mm thick on block masonry surfaces or other than fair faces of brick work in cement mortar 1:4. finished to even and smooth (without using extra cement)

M&L Rendering 15 mm thick cement plaster on concrete solid block walls in two coats first coat of 10 mm in CM 1:4 & 2nd coat of 5mm in CM 1:4 mixed with 3% integral water proofing compound finished to even & smooth w/o using extra cement. Note :- Integral water proofing liquid will be measured and paid seperately.

Supply only water proofing compound

M&L Preparing new plastered wall surfaces and applying two coat of oil bound distemper over chalk whiting, on plastered surfaces, preparatory to distempering, after applying 3mm thick wall care putty on wall

Preparation of New plastered surface and applying two coats of weather proof high glove antifungal paint on external surface with suitable primer

M&L 5 mm thick Rubber sheet with fabric backing or insert and plain coloured or marbled topping matt or glossy, laid in floors with approved adhesive in floors all as specified and directed by GE

S&F Powder coated aluminium grill of design DG-104 pattern, made out of 10mm dia rod fixed with and including stranded aluminium frame of 'F' section of size 23.4x15.3x1.4 mm thick all as per manufacturer's instructions complete all as specified and directed

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed

PROVISION OF COVERED SHED FOR STORAGE OF NITROGEN AND OXYGEN CYLINDER AT BSF (GOA) AT INS HANSA AGE E/M - I (INTERNAL ELECTRIFICATION)

M&L for point FRLS/LS wiring with 1.5 Sq mm nominal area PVC insulated and unsheathed cable single core multistranded, copper conductor in and including steel conduit on surface with all fittings and fixing materials and PVC insulated multistranded copper earth continuity conductor of size 1.5 Sq mm connecting all as specified and directed by Engineer-in-Charge.

S&F LED tube light fitting 1 x 36W flameproof type FLP-WP made of aluminium alloy LM6, with electronic ballast, bipin holders, connector block, etc. complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specifed and directed by Engineer-in-Charge.

PROVISION OF COVERED SHED FOR STORAGE OF NITROGEN AND OXYGEN CYLINDER AT BSF (GOA) AT INS HANSA AGE E/M - I (EXTERNAL ELECTRIC SUPPLY)

Supply and lay cable XLPE insulated screended PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 10 sqmm 2 core.

Excavation in trenches 1.5 Mtr wide and not exc 1.5 Mtr deep in hard / dense soil, getting out and levelling of bottom surface to required level for laying UG cable / errection of poles / pipes all as specified.

Excavation in trenches 1.5 Mtr wide and not exc 1.5 Mtr deep in soft / disintegrated rock getting out and levelling of bottom surface to required level for laying UG cable / errection of poles / pipes all as specified.

Returning filling in excavated earth work including spreading, levelling, watering and well ramming in layers n.exc 25cm thick in any strata

Supply/ filling dry river sand/m-sand in trenches for cable protection All as SSR Part I. NOTE : Punned thickness only will be measured & Paid

Supply and laying un-reinforced precast concrete cable cover LV type 1 flate size 250 x 150 x 40 mm

S&F Flame Proof SPN MCB DB 4 ways in LM6 termination box with following capacity of MCBs :- ( a) MCB SPN 16A-01 No (b) MCB SP 6 A - 02 Nos

M & L Earthing complete with galvanized steel earth plate electrode of size 60cm x 60cm x 6mm thick, buried directly in ground vertically earth pit not less than 2.25 mtr deep below the ground level with top to edge of the plate n. less than 1.5 mtr below ground level connected to galvanized iron wire 4 mm as earthing lead by means of blots, nuts, check nut and washer of galvanized steel, including necessary earth work and excavation in any strata and PCC 1:3:6 type C2 chamber and RCC cover and light grade GI pipe 40 mm dia pipe of required length for protection of GI wire and water funnel and wire mesh with GI pipe medium grade 20mm dia etc complete all as per electrical plate No 3 of SSR Part - I and all directed including connections and testing on completion.

ADDITION / ALTERATION OF CERTAIN ROOMS IN H3 HANGER (P-673) AT INAS 303 AT INS HANSA UNDER AGE B/R - I OF GE (NW) VASCO.

M&L Demolition of stone /boulder masonry, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L complete removal of existing treatment and Preparing old plastered wall surfaces and applying two coat of oil bound distemper over chalk whiting, on plastered surfaces, preparatory to distempering, after applying 3mm thick wall care putty on wall.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing), removing serviceable tiles to store and rubbish off the premises

M&L screed bed or bedding layer of mortar 15 mm thick cement plaster 1:4 for laying floor finished to receive floor tiles.

M&L Rendering 10mm thick in 1:6 CM on fair faces of block work or concrete surfaces to receive glazed tiles all as specified and directed.

Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

Glazed coloured ceramic tiles in vertical surface 350 x 250 x 7 mm/ 450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match

S&F powder coated aluminium door and window shutter and frame any type (sliding or openable) and other similar work etc 60 micron powder coated section, fabricated by using the JINDAL / INDAL / HINDAL CO / CENTURIAN sections including all necessary roller wheels for window, cleats, handle, door stoper locking arrangement and arrangements to received glass/ prelaminated particle board with aluminium beading and stainless steel screw incl cost of rubber gasket beadings etc complete sealing between frame & wall with epoxy sealing compound. (The weight of rubber gasket beading will not be measured with the weight of aluminium shutters, glass and prelaminated particle board will be measured and paid seperately) All sections as approved by GE.

S&F PVC ply Factory made 12 mm thick both side prelaminated of RAJSHRI PLASTIWOOD Prelam PVC sheets, laminated under pressure and temperature with hot stamping foil of various aesthetic veneer like appearance. The thickness of hot stamping foil shall be 30 micron with tolerance limit 10% when laminations done on both side complete all as specified and directed by Engineer-in-Charge.

S&F 4mm thick sheetglass ordinary quality exceeding 0.5 sqm each pane

Taking down chowkat or frames n exc 1.5 sqm each (w/o taking of shutters from the frame and removing to store)

Taking down chowkat or frames exc 1.5 sqm but n. exc 4 sqm each (w/o taking of shutters from the frame) and Refixing them into other openings

Factory made solid panel prelam PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of prelam PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F butt hinges medium weight stainless steel 100mm size

Extruded aluminium alloy handles, fabricated type, anodised 150mm size.

Aluminium anodised, barrel tower bolts of extruded section and fixed 150mm size

Aluminium alloy, anodised, sliding door bolt 250mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

Taking up or down steel water tubing and connections including cleaning for refixing or removing to store 20 mm dia .

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified of dia 20 mm.

Taking up or down steel water tubing and connections including cleaning for refixing or removing to store 32 mm dia .

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified of 32 mm dia

S&F Stop valves fancy type, chromium plated 20 mm dia, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F Wash basins 550 x 400mm vitreous china (flat back type) any size incl cutting for and pinning in end of brackets for erecting stand but exclusive of fixing of supply and waste pipe but including waste fittings

S&F in repairs chromium plated fancy type Bib taps 20 mm dia, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.

S&F Pillar taps fancy type of 20 mm dia, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S&F Push tap any colour high pressure of PTMT screwed for iron pipe and fixed. (minimum weight 15mm-47gms/20mm-75gms) of 20 mm dia

S&F Push tap in repairs any colour high pressure of PTMT screwed for iron pipe and fixed. (minimum weight 15mm-47gms/20mm-75gms) of 20 mm dia

M&L Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) 75 mm dia

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white including seat cover (excluding fixing bolts, flushing cistern and flush pipe)

S&F in repair PVC valveless, syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including brackets 10 litres capacity .

S&F in repairs Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern

S&F for hand shower (Health faucet) dia 8mm 1 mtr long flexible tube and wall hook Cat No ALD 573 of Jaquar or equivalent in Parko/Kohler

S&F in repairs Aluminium anodised Tubular towel rail, 20mm dia, D type, 60cm long between flanges .

S&F Soap dish, vitreous China white, approximate size 160x 160x90mm, fixed to plugs with chromium plated brass screws.

S&F in repair PVC Connections 15mm size with PTMT nuts of length 600mm

Dismantling of cast iron/AC drain pipes jointed in cement mortar

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in trenches or in floors.

S & F 75 mm bore PVC (SWR) bends of any radius

M&L complete removal of existing treatment and Preparing old plastered ceiling surface and applying two coat of oil bound distemper over chalk whiting, on plastered surfaces, preparatory to distempering, after applying 3mm thick wall care putty on ceiling.

PROVISION OF AIR CONDITIONER FOR PRECISION APPROCH RADAR ROOM IN BLDG P-29 OF BLDG AT INS HANSA UNDER AGE E/M – I.

Supply,install, testing and commisioning of split type air conditioner 2 TR capacity of 3 star rating with cordless remote control, single phase, 240 volts complete with all accessories such as indoor and outdoor units and refrigerant tubing of adequate length as required at site, indoor mounting plate, outdoor mounting bracket made of mild steel duly powder coated fixing with anchor bolts at any height, drain pipe of suitable size brought to ground level from any height including initial filling of refrigerant gas including making round hole on existing wall for taking up refrigerant tubing, drain pipe and cables etc and making good the disturbed surface by matching with existing adjoining surfaces and fix factory fabricated mild steel stand suitable for installation of out door unit of split type air conditioner fixing arrangement with anchoring bolts on wall surface at suitable height as per site condition complete all as specified and directed .

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4.0 KVA

S&F single pole and neutral enclosure with a 2 pin and earth plug and socket complete with one MCB SP 20 Amps, 10 KA 'C 'series, 240 Volts complete all as specified and directed.

M & L for FRLS sub main wiring with two runs of single core PVC insulated unsheathed 1100V grade multistranded copper conductor cable 04 Sqmm size PVC casing capping fixed in wall incl one run 04 Sqmm PVC insulated unsheathed copper conductor cable as earth wire complete all as specified.

NOTE :- SIMILAR ITEMS OF ALL WORKS HAS BEEN CLUBBED)

SHREE THATWAMASSY CONSTRUCTIONS PRIVATE LIMITED

M/S jvsr constructions

Super Construction

JINTECH

M/s J.D. DESAI

Tara Construction

SACHIN CONSTRUCTIONS

M/S Kartik Enterprises

M/S G.N.POWAR