TN_10_2

Amount

(A) Construction of Ground Floor Excise Office Building: Earth work in excavation for foundation trenches of walls, retaining walls, footing of column, steps and septic tank etc. including refiling (return filling) the quantity as necessary after completing of work, breaking clods in return filling dressing, watering and ramming etc. and removal of surplus earth with all lead & lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and spedified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil

Providing brick soiling in foundation and under floor with stone/best quality picked jhama brick, sand packed and laid to level and in panel after preparting the subgrade as directed including all labour and materials and if necessary dewatering complete. (a) Brick on flat soiling.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing, steps, walls, brick works etc. as directed and specified including dewatering if necessary and curing complete (Shuttering where necessary shall be measured and paid separately.) (a) In prop 1:3:6. (1 cement :3 coarse sand : 6 coarse aggregate by volume. (using mixture machine).

Supplying, fitting and fixing in position reinforcement bars conforming to relevent I.S. Code for R.C.C. work/R.B. walling including straightening, cleaning, cutting and bending to proper sharpes and length as per details supplying and binding with 20G annealed black wire and placing in position with proper blocks, supprots, chairs, spacers etc. complete. (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/Jindal Steel/Shyam Steel/RINL (i) TMT Corrosion resistant steel (CRS) reinforcement bar.

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and proping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4.0 m and removal of the same for in-situ reinforced concrete and plain concrete work in: 3.1.1.1. Foundation, footings, base of columns, pile cap, raft and mass concrete works etc. (b) Using 25mm thick plank

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and proping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4.0 m and removal of the same for in-situ reinforced concrete and plain concrete work in: 3.2.1.1. Colums, pillars, posts & strut of square/rectangular/polygonal in plan or any shape like Tee/L etc.having plane vertical face.

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and proping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4.0 m and removal of the same for in-situ reinforced concrete and plain concrete work in: 3.2.1.2. Sides and soffits of beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and proping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4.0 m and removal of the same for in-situ reinforced concrete and plain concrete work in: 3.2.1.3. Flat surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and proping etc. hight of propping and centering below supporting floor to ceiling not exceeding 4.0 m and removal of the same for in-situ reinforced concrete and plain concrete work in: 3.2.1.5. Sloping or Battering surface such as sloped slabs etc. including folded plates. (a) Where inclination to horizontal plane does not exceed 30 requiring shuttering only on the underside.

Providing and laying plain/reinforced cement concrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary and curing complete but excluding coast of from work and reinforcement for reinforced cement concrete work. (from work and reinforcement will be measured and paid separately) (i) Using mixture machine (a) In Sub-Structure up to plinth level Foundation, footing, colums with base, tie & plinth beam, pile cap, base slab, retaining walls, walls of the septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. (N) With out admixture, plasticiser (b) M-20 grade concrete ro prop.1:1.5:3

Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary and curing complete as directed. (I) In Sub-Structure upto plinth level including dewatering if necessary (b) In proportion 1:4

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming, etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (C) With silt (predominantly non plastic) by truck carriage including loading and unloading.

Providing and laying plain/reinforced cement concrete works cement with coarse sand & 20mm down graded stone aggregate including dewatering if necessary and curing complete but excluding coast of from work and reinforcement for reinforced cement concrete work. (from work and reinforcement will be measured and paid separately) (i) Using mixture machine (b) In Super Structure from plinth level up to 1st floor level. (ii) Colums, pillars, posts, struts, suspended floor, roof landing , shelf & support balcony, lintel, sill band, beam, girder, bressumer, cantilever, stair case (except spiral stair case and landing) including preparing the top surface & finishing of nosing. (N) With out admixture, plasticiser (b) M-20 grade concrete ro prop.1:1.5:3

Providing and laying 25mm thick damp proof coarse with cement concrete in prop 1:1.5:3 with graded store agg. Stone of 10mm down nominal size including providing approved damp proof admixture in proparation of recommended by the manufacturer including curing etc.complete as directed.

112mm thick 1st class brick nogged wall in cement morter including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (b) In cement mortar in proporation 1:4 (1 cement: 4 sand)

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 corse sand) finished with a floating coat of neat cement including rounding of junctions with floor. (a) 15mm thick.

Providing, fitting and fixing coloured anodised aluminium windows and ventilators of standard sections of approved brand without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels.(Cement concrete to be measured and paid separately). a) Side hung and Top hung windows and ventilators (iv) 5 mm clear glass

Providing, fitting and fixing coloured anodised aluminium windows and ventilators of standard sections of approved brand without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels.(Cement concrete to be measured and paid separately). b) Fixed windows and ventilators (iv) 5 mm clear glass

Providing, fitting and fixing anodised aluminuim framed glazed doors with anodised aluminium frame made of 100mm x 45mm x 2.5mm section of approved brand with door style of size 88mm x 45mm x 2.5mm, top rails 50mm x 45mm x 2mm lock rails 100mm x 45mm x 2mm and bottom rails 100mm x 45mm x 2.5mm fitted with glazing clip, special type rubber gasket complete including hydraulic floor spring, pivot, tower bolt in each leaf, aluminium door handle, lock, angles, cleat etc complete as specified and directed by the department at all levels. (iv) Prelaminated Board

Providing, fitting and fixing 40mm/ 48mm wood reinforced PVC chowkaths fixed to the columns/stiffeners/walls with necessary holdfast/sleeves etc. as specified and directed at all levels.

Providing, fitting and fixing 24mm/ 29mm thick polymer reinforced moulded PVC door shutters fixed to the chowkath with necessary hinges, screws, bolts etc. as specified and directed at all levels (Door fixtures and fittings to be measured and paid seperately) b) 29mm thick

Providing and fixing 12mm thick and 150mm wide pelmet with 25mm dia wooden curtain rod and bracket including fixing with 15mm x 3mm M.S flat 100mm long plugs complete. E) Extra for providign and fixing bars curtain rail with rollers, stoppers and brakets in pelmet instead of wooden curtain rods 25mm dia with brakets (actiatl length of the rods to be measured)

Providing fitting and fixing M.S grill of requiredpattern for windows/clerestory windows/opening with M.S flats at required spacing in frame all round squre or round M.S bars with round headed bolts and nuts or screws. I. Plain grill (c) Fixed to Brickwork/PCC/RCC

Providing and fitting stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding, grinding, buffing polishing and making curvature (wheraver required) and fitting the same with necessary stainless steel nuts and bolts complete, i.e. fixing the railing with neccessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge. (for payment, only weight of stainless steel member is to be considered. no extra payment for fixing accessories such as nuts, bolts, fasteners etc. will be considered.)

Plain cement concrete floor base in prop 1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. c) 100mm thick

VITRIFIED TILES A) ON FLOOR Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) b) Executive range Somany/Orient/Nitco/Varmora/VITA/ Marbito/ Make i) Of size 800mm x 800mm and above

B) ON WALLS Providing polished vitrified wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/white cement slurry mixed with approved pigment to match shade of tilesc complete at all levels as specified and directed. (coloured pigment should be in conformity with colour of tiles and as approved and directed by the department). i) Of size 300mm x 450mm and above

Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1cement :3 coarse sand) approved make Fix-A-Tile (Choksey/Sika/Pedlite/Rouf) white cement complete at all level as specifoed and directed. VITRIFIED (ii) Executive range-1 (Size 600mm x 300mm and above) a) Nitco made (Oak Wood)

18mm thick marble stone slab flooring of size 1200 x 1200 including treads and risers of steps, skirting laid over 20mm thick base of cement plaster 1:6 (1cement: 6 coarse sand) laid and joined with grey cement slurry including rubbing and polishing complete with marble slab of specified quality and shade at all levels. (i) Dungri slab

15mm thick cement plaster in single coat on rough side of single or half brick wall for interior plastering upto 1st floor level including arrises, internal rounded angles not exceeding 80 mm in girth and finished even and smooth including curing complete as directed. A) On rough side (b) In cement mortar 1:4 (1 cement : 4 sand)

Providing surface preparation for walls, ceilling etc, using average 1.50mm thick plaster of paries of pares including rubbing with sand paper filling gaps, depression etc. where necessary with chalk powder and plaster of pairs paste making the surface even and smooth complete at all levesl as specified and directed.

Providing two coats of acrylic water based wall putty/ wall filter of Asian Paints/Berger/ Dulux over concrete/cement plaster/brick walls and ceilling both internal and external after removing all the loosely adhering material from the wall/ceilling surface with the help of emery stone, putty blade or wire brush, moisterning the wall with the help of sufficient quantity of clear water as specified and directed by the department.

Wall Painting (two coats) with plastic emulsion paint of approved brand and manufacture (Asian/paint/Berger paint/ICI paint/J & N /Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a) Plastic Emulsion Paint of approved brand and manufacture (Asian paint/Berger paint/ICI paint/J & N paint/Nerolac)

Applying one self- priming coat of acrylic emulsion paint of approved brand, thinning by adding water as per the specification of manufacturer over freshly plastered wall surface after throughly brooming the surfaces free mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth as specified and directed by the department. c) Asian paint

Finishing wall with two coats of acrylic emulsion exterior paint of approved brand of required shade, thinning by adding water as per specification of manufacturer after throughly brooming the surfaces to removed all dirt and remains of loose powdered materials as specified and directed by the department. c) Asian paint

Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes, fine stees, wood scrapers and sand paper. a) With ready mixed red-lead/red oxide primer.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian paint/Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (i) Surfaces over 100mm in width or girth b) High gloss (Asian paint/Berger paint/ICI paint/J & N paint/Nerolac)

Applying priming coat over new wood and wood based surface over 100mm in girth/width after and including preparing the surface by throughly cleaning oil grease, dirt and other foreign matter sand papering and knotting. (b) With ready mixed paint wood primer (pink)

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/Berger paint/ICI paint/J & N paint/Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter sand papering and stopping. (i) Surfaces over 100mm in width or girth. b) High gloss (Asian paint/Berger paint/ICI paint/J & N paint/Nerolac)

Providing drain with brick work in cement mortar in prop 1:5 with half brick thick side walls and 100mm thick CC (1:3:6) base over one brick flat soiling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shettering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. (ii) 300 wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Providing plinth protection with bricks flat laid in cement mortar 1:4 and finished with 15mm thick cement plaster in prop 1:2 with a floating coat of neat cement finish.

Providing, Fixing, testing & Commissioning of Single Headed Gun Metal ISI Marked oblique pattern Hydrant Landing Valve with 80 mm dia, flanged inlet & 63 mm dia instantaneous type female outlet complete with cap and chain, twist release lug and all accessories as per IS:5290-19833 (Type-'A') and specifications complete as reequired . (MAKE:ESSEL/WINCO/NEWAGE)

Providing and fixing clear sheet glass beded in putty and fixing with/wiithout wooden beadings including necessary cutting of glass to required sizes (payment for wooden beads shall be made separately). (2) Area of glass panes not exceeding 0.15sqm. but not exceeding 0.52m2. (b) 4.00mm thick

Sanitary Installation and Water Supply Works: Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high) with seat and lead, CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) A) Parryware make a) White (i) Universal Closet S Trap (Cat No.C0271) (Anglo Indian) (inclusive of seat cover)

Supplying fiting and fixing PVC flushing cistern with all internal fitting with CI brackets including fitting and fixing standard size CP flush pipe union clamps etc. complete as directed and specified ( pipes will be measured separately) I) parryware make a) White (i)Economy Single Flush (Cat No.C8090/C8055)

Providing fitting and fixing vitreous china flat back type lipped front urinal basin with standard flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (A) Parryware Make (a) White (ii) Aquaseal (Cat. No.C0508)

Basin (without pedestal) (A) Parryware Make (a) White (i) Star Basin 550 x 400 (Cat. No.C0450)

Providing fitting and fixing Mirror with plastic frame of size 500x400mm complete as directed and specified.

Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified. (A) Parryware Make (i) Recess SP & SG dish (Cat.No. C9935)

Providing, fitting and fixing CP towel rail complete as directed and specified. (c) Parryware make (Cat.No.C9948)

Supplying fitting and fixing overhead adjustable Chrome Plated (C.P.) spray shower 15mm dia. of Sona make with wall flange as directed and specified.(pipes will be measured and paid separately) (b)Apex/Kiran/Priya/Star/RimZim/Bugle shower with arm

Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (A) Exposed or in trenches SUPREME/ PRINCE/ SFMC BRAND or other equvalent approved brand (High presure pipe Sch-40) Exposed or in trenches d) 25 mm dia

Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (A) Exposed or in trenches SUPREME/ PRINCE/ SFMC BRAND or other equvalent approved brand (High presure pipe Sch-40) Exposed or in trenches e) 20 mm dia ii) Using other ISI marked approved brand

Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (A) Exposed or in trenches SUPREME/ PRINCE/ SFMC BRAND or other equvalent approved brand (High presure pipe Sch-40) Exposed or in trenches f) 15 mm dia ii) Using other ISI marked approved brand

Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) (I) Essco make (Delux/Sumthing spl./Tropical) (a) Bib cock short body

Supplying fitting and fixing stop-cock of approved brand of size as mentioned below and directed and specified (G.I. & C.P. pipes will be measured and paid separately) I) Brass stop cock (heavy) of Sant make (i)15mm dia

Supplying fitting and fixing stop-cock of approved brand of size as mentioned below and directed and specified (G.I. & C.P. pipes will be measured and paid separately) I) Brass stop cock (heavy) of Sant make (ii) 20mm dia

Supplying fitting and fixing stop-cock of approved brand of size as mentioned below and directed and specified (G.I. & C.P. pipes will be measured and paid separately) I) Brass stop cock (heavy) of Sant make (iii)25mm dia

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. (ii) Jaguar make (a) Continental

Supplying fitting and fixing Chrome Plated (C.P.) flush cock of approved brand as directed and specified.(G.I. & C.P pipes will be measured and paid separately) (I) Agmeco brand a) Flush cock Economy Cat No.00506

Supplying, fitting and fixing Chrome Plated (C.P.) wall mixer complete as directed. (ii) Agmeco brand a)Wall mixer non telephonic Cat No.00211

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed B) UPVC pipe with uPVC fittings ( Using uPVC high pressure pipe) vii) 65mm diameter

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed B) UPVC pipe with uPVC fittings ( Using uPVC high pressure pipe) x) 110mm diameter

Supplying fitting and fixing Hand pump for 40 mm dia tube well with all accessories complete as directed. i) Maya popular - 6

Labour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department. iv) Bore hole of 150mm diameter

Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department. II PVC PIPE SUPREME /PRINCE / FUSION /SFMC Brand vi) 140mm diameter

Supplying, fitting and fixing suction pipes plain/bevel ended, conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casing pipes complete as directed. B) PVC PIPE SUPREME /PRINCE / FUSION /SFMC Brand vi) 75mm diameter

Supplying fitting and fixing ISI approved PVC filter 3.00 metre long. v) 150mm diameter

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes (I) 2000 Lt capacity (a) Sintex make

Single phase Submersible motor pump set (Texmo / Crompton Greaves/ Aquatic/ CRI/ V-Guar suitable for 100 mm bore well and above. 1.5 HP STAGE 5 to 26 with control panel.

Septic Tank 4 Nos.: Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Upto a depth of 2.00 m below the existing G.L.

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a).Brick on flat soling.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (a). In prop. 1:3: 6 (1 cement:3 coarse sand : 6 coarse agg. by volume (using mixture machine)

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete (upto 1st floor level). c) ISI approved Mild steel reinforcement bar (M.S.Bar)

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness. (ii) Using 25mm thick plank

Brick work in cement morter with 1st class brick including racking out joints and dewatering if necessary, and curing complete as directed . (I) In sub-structure up to plinth level including dewatering if necessary (b) In proportion 1:4

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine (A) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. N) Without using admixture, plasticiser a) M15 grade concrete or Prop. 1:2:4

15 mm thick Cement plaster in single coat on rough side of single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. (A) On rough side (b) In Cement mortar 1:4 (1 cement : 4 sand )

Internal Electrification : Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19mm ISI marked casing 'n' capping (AKG/Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in recessed system, including 6 Amp flush type switch/ bell push (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover, ceiling rose (Anchor /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the deptt. Short point up to 3.00 metre. length.

Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19mm ISI marked casing 'n' capping (AKG/Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in recessed system, including 6 Amp flush type switch/ bell push (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover, ceiling rose (Anchor /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the deptt. Medium point up to 6.00 metre. length.

Wiring for light/fan/call bell point with 2x1.5 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19mm ISI marked casing 'n' capping (AKG/Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in recessed system, including 6 Amp flush type switch/ bell push (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover, ceiling rose (Anchor /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the deptt. Long point up to 10.00 metre. length.

Wiring to 5 pin 6 Amps plug point with 1.5 sq.mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR Conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kable/Nicco/Anchor or Equivalent Make as approved by the Deptt.) with flat 19mm ISI marked casing 'n' capping (AKG/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the deptt.) in surface/recessed system, including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta/Gold medal/Kolor kany.kom/Havells or equivalent make as approved by the Deptt.) GI/MS switch board (ISI marked) with phenolic laminated sheet cover including earth continuity with 1.5 sq.mm. cable to third pin of the plug socket etc. as required complete, when placed on the same board of light and fan point.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19mm ISI marked casing 'n' capping (AKG/Precision/presto plast/Polycab/MW or equivalent make as approved by the Deptt.) in surface system, including providing and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt./ Havells make), GI/ MS switch board (I.S.I. marked) with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete. Long point up to 10.00 metre. length.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco/Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco/Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. With 2 x 4 sq. mm. + earth continuity with 1x 2.5 sq. mm. cable in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco/Anchor or Equivalent Make as approved by the Deptt.) in surface with flat ISI marked casing 'n' capping (AKG/Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) system including earth continuity. With 3 x 4 sq. mm. + earth continuity with 1x 2.5 sq. mm. cable in 25 mm. ISI marked casing 'n' capping system.

Supplying and fiixing of batten holder (Anchor Penta PC CHERRY/Gold medal/Kolor kany.kom/Havells or equivalent make as approved by the Deptt.) including connection as approved by the Deptt.) as required With out Lamp.

Supplying and fiixing of bulk head fitting suitable for CFL lamp complete with all accessories including 20 watts CFL lamp and connecting as approved by the Deptt.) as required.

Supplying and fiixing of 250/305 mm dia (Nominal Size flush type circular celling fittings complete with holder, Aluminium anodized back plate and brass holder 20 Watt CFL lamp including connection as approved by the Deptt.) as required.

Supplying and fitting of 18/20 Watt CFL lamp in the existing batten holder/angle holder/decorative bracket/bulk head fitting/pendent holder etc. as specified and directed by the deptt.

Supplying with fitting and fixing sheet steel, phosphatised powder painted single door surface mounting MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necesssary connecting as approved specified and directed by the deptt. 12 way SPN Single door.

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved specified and directed by the deptt. B-Series (Schneider MG, legrand, Hager make) 6 to 32A

Supplying with fitting and fixing TPN 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved specified and directed by the deptt. C-Series 40A

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved specified and directed by the deptt. C-Series (Scheneider neo break, C&S, Havells, Indo Asian, HPL, V-Guard or equivalent make as approved by the deptt.) 63A

Supplying with fitting and fixing panel mounting open execution 25KA 415V 50Hz 4P MCCB (Ics=Icu, adjustable Ir setting 0.7) without enclosure) of the following capacity complete with making necessary connection as approved by the deptt) as specified and directed by the deptt. 25 KA 415V 50 Hz 3P MCCB (Havells, HPL, Indo Asain Make) 125A

Supply installation & testing of G.I earth station with perforated 40 mm dia and 4.50 Metre long heady duty G.I pipe with necessary 40 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mm x 40mm G.I reducing socket for funnel including locking arramgement 300mm x 300mm x 6mm hinged cover C.I. earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt.

Extra for using salt (5 K and Charcoal (64 K in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the Deptt.

Supplying & laying of 8 SWG Copper. Earth from Earth Electrode (below G.L) to electrical switch gears or electrical machineries including making necessary connection as approved specified and directed by the deptt.

Supplying including fitting fixing of following A.C. ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.) as required complete and as directed by the Department ( Without requlator). Premium model 1400 mm Sweep. (ORIENT PSPO make)/ Premium model 1400mm Sweep SS-390 Deco. Havells make).

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.) as required complete and as directed by the Department. Power Flow 225mm sweep (ORIENT make)

Supplying fitting and fixing of ceilling fan regulator including connections etc. complete as required. Electronic type.

Supply and laying of following size PVC/XLPE insulated and PVC sheathed 1.1 KV G Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour (Aluminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2x10 sq mm.3x10 sq mm,4x6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable U.G. cable laid in ground/partially in air (as required for termination over ground including excavation of cable trench up to depth of 75cm, refilling, protective brick covering, Sand cushioning etc complete handling of surplus spoil, debris etc. to proper place as specified and directed by the deptt. (Nicco/Havells/RPG/CCi/Oolycab/Gloster/Finolex make or equivalent) 3&1/2 Core A2XWaY A2XFaY 35.00 Sq mm 3&1/2 Core armoured U.G cable (For service line)

External Electrification: Supplying, installation testing and commissioning of the following rating copper wound in door / out door type transformer complete including the payment to be made to power supply authority for supervision charge, labour charge, cost of L.T/H.T metering etc. (excluding the cost of load security) and making necessary arrangement for charging approval of the sub-station from the competent authority as directed and specified by the department. Transformer should be as per CEA guidelines as ammended up to date upto 200 KVA star rating up to 5 star, above 200KVA as per CEA guidelines for losses along with LV enclosure. 63 KVA, 50Hz.11/0.433 KV. Oil filled transformer with Off Circuit tap change.

Supplying and erection PSC pole 9.75mt long the pole is to be erection in 1:3:6 plain cement concrete foundation of size 1.50 x 0.45 m x 0.45m having PCC base foundation 15cm x 60cm x 60cm including edge brick soiling and plastering above G.L. portion (0.30 metre complete with excavation of earth, handling of Surplus Soil, debris etc. to the proper place and refilling etc.

Supplying and string up AAAC Racoon conductor in the existing PSC/MS/Galvanized pole with binding etc. as required and as directed by the department, directed by the department.

Supplying and erection of H.T stay set complete (Galvanished) with 19mm dia. X 1.8m long stay rod anchor plate of size 30 cm x 30cm x6.4mm thimble stay clamps tube buckle (19mm x 60mm) 7/3.15mm dia. G.i stay and strain insulator etc. In cement concrete 1:3:6 (1 cement 3 course sand 6 course graded stone aggregate 40mm nominal size) foundation including excavation and refilling etc.

Suppyling and fitting fixing of galvanished channel of 75mm x 40mm x 65mm x 2200mm long complete with clamps, bolts, nuts, etc, as required and as directed by the deptt.

Supplying and erection of 11KV pin insulator (poly) with G.I. Pin bolts and nuts coach screws etc. as required and as directed by the deptt.

Supplying and erection of 11KV Disc insulator (Poly) 45KN with Hardware fitting etc. as required and as directed by the deptt.

Supplying and fixing of 11 KV 400A Gang Operated Switch will all accessories complete as required and as directed by the deptt.

Supplying and fixing of 11 KV 150A D.O fuse set complete as required and as directed by the deptt.

Supplying and fixing of 11 KV 5 KA Lighting Arrestor (POLY) set complete as required and as directed by the deptt.

Metering Cabinet (Rate as per APDCL)

DTR fencing as per specification (Rate as per APDCL)

Payment to be made to APDCL authority for load security and Meter security and 3 phase service connection.

(B) Construction of Boundary Wall: Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil

Providing brick soiling in foundation and under floor with stone/best quality picked jhama brick, sand packed and laid to level and in panel after preparting the subgrade as directed. (a) Brick on flat soiling.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing, steps,walls,brick works etc. as directed and specified. (a) In prop 1:3:6 (1 cement: 3 coarse sand: 6 coarse agg. By volume (using mixture machine)

Supplying, fitting and fixing in position reinforcement bars conforming to relevent I.S. Code for R.C.C. Work/R.B. Walling including... b) Other ISI approved TMT reinforcement bar (SAI/BISCON/THERMAX)

Providing form work of 12mm thick plywood board so as the give a rough finish including centering, shattering, strutting and propping. 3.2.1.1. Colums, pillars, posts & strut of square/rectangular/polygonal in plan or any shape like Tee/L etc. having plane vertical face.

Providing & laying plain/reinforced cement concrete works cement with coarse sand & 20mm down graded stone aggregate including...... (I) Using mixture machine (a) In Sub-Structure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. N) Without using admixture, plasticiser. b) M20 grade concrete ro prop.1:1.5:3

Providing & laying plain/reinforced cement concrete works cement with coarse sand & 20mm down graded stone aggregate including...... (I) Using mixture machine (a) In Super-Structure from plinth level up to 1st floor level. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing) including preparing the top surface and finishing of nosing. N) Without using admixture, plasticiser b) M20 grade concrete ro prop.1:1.5:3

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. I) In sub-rstructure up to plinth level including dewatering if necessary. B) In prop 1:4

112 mm thick 1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth upto 1st floor level A) 112mm thick brick wall. a) In cement mortar in proporation 1:4 (1 cement: 4 sand)

15 mm thick cement plastering in single coat on rough side of single or half brick wall for interior plastering up to 1st floor level including A) On rough side (b) In cement mortar 1:4 (1 cement: 4 sand)

(a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after thoroughly brooming the surfaces......

(b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new wall surface (two.............

Supplying fitting and fixing double leaf heavy duty iron gate frame made from 50mm x 6mm M.S flat iron with another horizontal flat at the middle, 20mm dia M.S bars at 200mm apart from bottom flat to top and 20mm dia M.S bars 200mm apart from bottom flat to middle flat including drilling welding etc. complete.

(C) Earth Filling: Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royalty, sales tax, land compensation, Municipal gate fees if any monopoly duty etc. (profile meassurement to be taken and 12.5% deduction for shrinkage to be made from total quantuty) etc. complete as per directed and specified, including forest royalty within a distance of 8.00km (Forest royalty shall be reimbrushed on production of necessary certificate from the forest authority duly countersigned by DFO concerned).

BABITA BASUMATARY

LAJIK BRAHMA