SPECIAL REPAIRS TO OTD PUMP HOUSE BLDGS AND WELCOME MAINTENANCE INCL MISC REPAIRS TO OFFRS MD ACCN IN ARMY AREA UNDER GE AVADI

Amount

Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified. complete all as specified and as directed.

Demolition of cement conctrete (un-reinforced) of any description and in any position not otherwise specifically provided all as specified and as directed.

50mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) with water proofing compound and finished even and fair complete all as specified and as directed. Note : Supply only water proofing compound will be measured and paid separately

Supply only integral water proofing compound complete all as specified and directed.

PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in roof kerbs, benching etc rounded or chamfered angles and throating complete all as specified and as directed. Note : Supply only water proofing compound will be measured and paid separately

Dismantling of APP based polymeric membrane reinforced with polyster non-woven fabric (measured flat and not girthed) complete and cleaning the top surface of roof with wire brush and washing with hydrochloric acid to remove dust, dirt, oil, grease, loose particles etc., and provide water proofing treatment with membrane type water proofing method using APP modified prefabricated five layer water proofing membrane mat finish, 3 mm thick and weighing not less than 3.6 kg/sqm reinforced with non woven polyester matt black weighing not less than 100 gm/Sqm, having softening point not less than 140 degree Celsius, longitudinal tensile strength not less than 300 N/Sqm, laid over one coat of bitumen primer at 0.20 Kg/sqm and torch application of membrane using gas burner with 150 mm overlap on side lap and end lap as per manufacturers instructions with top most layer of surface finished with two coats of solar reflective aluminium paint @ 0.10 Litre/Sqm per coat etc., complete all as specified and as directed. Note: (i) The work shall be executed through Manufacturer's authorised applicator approved by GE. (ii) The quoted rate is deemed to include the cost of digital photograph and plaster plate as per PS.

Taking down chowkats or frames not exc 1.5 Sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Taking down chowkats or frames exc 1.5Sqm and not exc. 4Sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed.

Forming Jambs etc to openings (to forgoings items) incl cutting, toothing and properly bonding into old work also facing, jointing and pointing to match existing work in CM 1:6 complete all as specified and as directed

Anodised aluminium Powder coated door shutters (powder coating of any colour .Thickness of powder coating not less than 50 micron), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed

Anodised aluminium "Powder coated" window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 Nos.) suitable handle (1 no.) complete all as specified and directed

Anodised aluminium Powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed

Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet and edges will be painted to match with prelam sheet, reinforced with 19mm MS square tube of 19 gauge mitred out at two corners and joined by inserting two Nos of 150mm long brackets of 15mm x 15mm MS square tube inside the drilling 100mm long MS screws using PVC fastener as per specification and drawings as shown in SSR Part II of 2020 complete all as specified and as directed.

Factory made solid PVC moulded door shutter with wood free EPS 28 to 30mm thick (stiles) with 2,4,6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face and 2mm Plain colour PVC Sheet on back face, supplying and fixing in frame at site as per specification and drawing shown on SSR Part-II (2020) complete all as directed.

125 mm long aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed.

300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

Mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 all as specified and directed.

4mm thick figured glass, pin head type and glazing with oil putty in squares n.exc 0.50 Sqm in each pane, complete all as specified and as directed.

4mm thick sheet glass ordinary quality, glazing with oil putty or wooden beads in squares nexc 0.5 sqm in each pane, complete all as specified and as directed

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed

Dismantling structural steel work including doors, gates, rolling shutter but excluding framed truss etc., all as specified and as directed

1.00 mm thick rolling shutters, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type, complete all as specified and as directed

Ball bearing for rolling shutters complete all as specified and as directed

Safety lever locks of mild steel with 4 levers for rolling shutters complete all as specified and as directed

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work, complete all as specified and directed.

Brickwork with fly ash Old size bricks straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed

Fly ash brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed

Rendering 10mm thick on fair faces of brick work or concrete surface, in cement mortar 1:4 finished the surface even and smooth without using extra cement, complete, all as specified and directed

Rendering 15mm thick in CM 1:6 on other than fair faces of brick work or stone masonry surfaces, even and smooth (without using extra cement) , complete all as specified and directed. Note:- WPC will be measured and paid seperately.

Rendering 5mm thick on ceiling, in cement mortar 1:3 finished the surface even and smooth without using extra cement , complete, all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection surfaces finished even and fair without using extra cement, complete all as specified and as directed.

Glazed ceramic coloured tiles (300x200mm) x 6 to 7mm thick, as in vertical surfaces such as in skirting and dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick back coat in CM (1:3),complete all as specified and directed.

Non - skid Ceramic coloured tiles 7 to 8 mm thick square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick screed bed in CM (1:4) complete all as specified and directed.

Preparation of newly plastered surface of walls and applying two coats of oil bound distemper and one coat of 3mm thick wall care putty over chalk whitening primer complete all as specified and directed.

Preparation of newly plastered surface of walls and applying two coats of exterior emulsion paint and one coat of wall care putty over chalk whitening primer complete all as specified and directed.

Preparing newly plastered of ceiling surfaces and applying three coats of white wash complete all as specified and directed.

Taking up or down steel water tubings and connections of 15mm bore pipe including cleaning or re-fixing or removal to store , complete all as specified and directed.

Taking up or down steel water tubings and connections of 20mm bore pipe including cleaning or re-fixing or removal to store, complete all as specified and directed.

Tubes 15mm, medium grade' galvanised, with all GI fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Tubes 20mm, medium grade' galvanised, with all GI fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

15mm bore stop valve/Angle valve, chromium plated fancy type cast copper alloy, screwed down high pressure, with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed of,complete all as specified and directed.

Supply and fixed in repairs 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe , all as specified and directed.

15mm bore stop valve, cast copper alloy, screwed down high pressure, with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed of,complete all as specified and directed.

15mm bore Pillar taps bore cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe, complete all as specified

15mm bore Bib taps, cast copper alloy chromium plated with crutch or butter-fly handle screwed down, screwed for iron pipe or for brass ferrules, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks, 750 ltrs capacity (Cylinderical vertical with closed top) and fixed in position, all as specified in SSR Part-I, including dismantling of old water tank of any description, complete all as specified and directed.

Supply and fixed in repairs 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 142gms) complete all as specified and directed.

PVC connection 15mm size with PTMT nuts of length 600mm,complete all as specified and directed.

Supply and fixed in repairs Vitreous China squatting pan of 'Orissa' pattern of size 580 x 440mm, white, with integral foot rests, complete including provision of lime concrete bedding all as specified and directed.

Supply and fixed in repairs 10 ltr capacity PVC valveless symphonic action type flushing cistern low level white with inlet ball valve, float and handle/push including brackets and PVC flushing pipe 32mm bore, complete all as specified and directed.

Supply and fixed in repairs Vitreous China wash Basin (flat back or angle back type) , of size 550x400mm including brackets, waste coupling PTMT, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc, complete all as specified and directed.

Supply and fixed in repairs Sinks with drainage board made of stainless steel 1mm thick kitchen of laboratory with plugs, washers and wastes: including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

Taking down PVC (SWR) pipes 110/75mm internal dia laid in trenches or fixed to walls incl all fittings complete all as specified and directed.

PVC (SWR) pipe 110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

PVC (SWR) pipe 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

75mm bore PVC (SWR) bends any radius, complete all as specified and directed.

110mm bore PVC (SWR) bends any radius, complete all as specified and directed.

Supply and fixed in repairs 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement, all as specified and directed.

PVC (SWR) vent cowl complete all as specified and as directed

Chipping, Chiselling surface mechanically with chipping machine :- (1) Providing zinc rich primer for exposed reinforcement (2) Providing 100 x 100 x 3 mm weld mesh and fixing the same with shear connectors of 8mm dia with epoxy resin (3) Guniting the area with CM 1:3 of over all thickness 50mm in with two layers in small areas/patches complete all as specified and as directed

Crack repair work in walls :- Clean surface around crack, joint should be free from loose particles and dust, cutting 'V' shaped groove of size in range of 6 to 25 mm of width and depth along the crack line by machine or manually, then clean the groove by wire brush to remove loose particles and then washed by water jet, and fixing nozzle and repairing cracks using Fosroc Rendroc CS chemical with a proportion of 1 part of water to 2.5 -3.0 part of Renderoc CS by volume or w/p ratio 0.36 by weight complete all as specified and as directed.

Crack repair work in RCC areas :- Chipping the loose particles upto 300mm distance on both side of crack and depth 25mm behind the reinforcement bar and corrosion treatment done to existing rod and then bonding agent nitobond SBR applied to the surface, bottom shutttering to be provided before concrete pouring, and apply MICRO CONCRETE using Rendroc RG complete all as specified and as directed

Formwork to suspended slabs such as roof slabs, floor slabs landings and similar work nexc 200mm thick; make rough finished surfaces complete all as specified and as directed

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floors and roofs nexc 20 cm wide sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but nexc 20cm wide complete all as specified and as directed

Formwork to chullah hoods, chajjas, troughs and similar items including edge complete all as specified and as directed

RCC design mix M-30 using 20mm graded aggregates in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed

RCC design mix M-30 using 20mm graded stone aggregates in Chajjas complete all as specified and as directed

TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M depth for foundation etc in hard/ dense soil all as specified and directed.

Reinforced concrete pipes, 100mm bore class NP2, laid and jointed complete with collars laid in trenches and set and jointed in CM 1:1, including demolition and breaking of existing salt glazed ware/ AC/ Reinforced concrete pipe complete all as specified and as directed.

Reinforced concrete pipes, 150mm bore class NP2, laid and jointed complete with collars laid in trenches and set and jointed in CM 1:1 including demolition and breaking of existing salt glazed ware/ AC/ Reinforced concrete pipe complete all as specified and as directed.

Reinforced concrete pipes, 200mm bore class NP2, laid and jointed complete with collars laid in trenches and set and jointed in CM 1:1 including demolition and breaking of existing salt glazed ware/ AC/ Reinforced concrete pipe complete all as specified and as directed.

Cement concrete bed to SWG/Reinforced concrete pipe line of 100mm bore with PCC (1:3:6) type C2 (using 40mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed.

All as per Item No 77.00 described herein before but for 150mm bore pipe.

All as per Item No 77.00 described herein before but for 200mm bore pipe.

Precast cement concrete in (1:2:4) type B1 (using 20mm graded stone aggregate) set in cement mortar 1:6 as in landings, cover slabs chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain face including necessary form work complete all as specified and directed.

Material and labour for rendering 15mm thick in cement mortar (1:4) with WPC on other than fair faces of brick work or concrete surface as in manholes, Septic tank etc., finished fair and even complete all as specified and as directed. Note : WPC shall be measured and paid separately

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm using excavated soil complete all as specified and as directed.

Removal of excavated surplus soil to a distance exc 50 m and not exc 250m and depositing where directed at a level n. exc 1.50m above the starting point and all as specified and as directed.

Plain Cement concrete , 100mm thick, 1:5:10 type E2 using 40 mm graded stone aggregate thick as in sub base in path / hardstanding all as specified and as directed.

Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with Grey cement and no pigment over 15mm thick screed bed of CM 1:4 all as specified and as directed.

100mm thick Plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate) as in sub base under floor/path all as specified and directed.

40 mm thick Plain cement concrete 1:2:4 Type B1 (20mm graded aggregate) as in flooring, surfaces finished even and fair complete all as specified and directed.

MS Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete with Fe 410 -W(Gde-E- 250)-qualityA all as specified and as directed.

Formwork to side of columns, fair finished surfaces of concrete square, rectangular and similar work vertical or to batter for flat surfaces complete all as specified and as directed .

Reinforced cement concrete type A1 1:1.5:3 using 20mm graded aggregate(Nominal mix design) for columns, pillars, piers, posts and struts complete all specified and directed.

Excavating in post holes each not exc 0.5 Cum getting out hard and dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exc 50m and making good surface all specified and directed.

PCC 1:3:6 type C2 using 40mm graded stone aggregate as in foundation filling mass concrete etc . all specified and directed.

Joist, channel, angle, or tee sections Fe-410-W(Gde E-250 quality A), fixed independently, without connection plate, etc. all specified and directed.

Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thickof an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall,fixed with self tapping screws all specified and directed.

Pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thickof an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall,fixed with self tapping screws all specified and directed.

Taking down shutters of any description exc 1 Sqm & nexc 2 Sqm each complete all as specified and as directed by Engr-in-Charge.

Second class hard wood plain, solid, straight, chowkats and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue pinned complete all as specified and as directed.

Small articles of steel such as hold fast, etc of Gde Fe 410-0 or Fe-290 Gde E-165 complete all as specified and directed.

PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in hold fast etc completed all as specified and directed.

Preparing and treating ends of posts, back of chowkats with coal tar black paint, area tarred exc. 0.10 sqm but not exc. 0.50 sqm all as specified or as directed.

35mm thick, 2nd class hard wood, plain, framed, panelled shutters (any number of panels), with panels of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats complete all as specified and directed.

35mm thick, 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc.(without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc; size of members of shutters as specified in SSR part I, section 8, clause 8.24(a); supplied and fitted to chowkats complete all as specified and directed.

30 mm thick Flush door shutter, solid core construction with particle board core and plywood face panels commercial type on both side complete all as specified and as directed.

Preparation of new wood surfaces of any description over 10cm width or girth and priming with pink primer and painting with synthetic enamel painting two coats all as specified and directed.

Taking down shutters of any description exc 1 Sqm & nexc 2 Sqm and easing, adjusting and also refixing builders hardware as required and renewal of unserviceable screws and refixing in the same opening incl painting touch up to match with the existing colour complete all as specified and as directed.

Solid PVC door frame of size 50mmx47mm made out of 5mm thick plain colour PVC sheet reinforced with 19mm MS square tube of 19 gauge mitre cut at two corners and joined by inserting two Nos of 150mm long brackets of 15mmx15mm MS square tube inside the 19mm MS square tube and suitably screwed complete all as specified and as directed.

100mm size, butt hinge medium weight cold rolled mild steel & fixed complete all as specified and directed.

75mm size, butt hinge medium weight cold rolled mild steel & fixed complete all as specified and directed.

150mm length aluminum, anodised, barrel tower bolts of extruded section and fixed all as specified and directed.

100 mm length aluminium, anodised, barrel tower bolts of extruded section and fixed all as specified and directed.

150mm size aluminium handles, cast type anodised complete all as specified and directed.

100mm size aluminium handles, cast type anodised complete all as specified and directed.

Floor door stopper 150mm size of aluminium alloy body and tongue, anodised, with hard drawn steel spring fixed in floor all as specified and directed.

300mm ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and fix in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width aperture 1.40mm and fixed with stainless steel wire staples all as specified and as directed

Supply and fixed in repairs anodised aluminium frame (Powder coated) for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed

Supply and fixed in repairs anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws, etc. complete all as specified and as directed

Aluminium rebated mortice lock vertical type size 100mm four lever complete all as specified & directed.

5.5mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.50 Sqm in each pane complete all as specified and as directed

12mm thick prelaminated particle board exterior garade prelaminated one side with decorative choice lamination & otherr side balancing white lamination fixed with screws to aluminimum frame work shutter etc.,all as specified and as directed.

Supply and fixed in repairs anodised aluminimum window shutters, fixed type without sash bar, aluminimum section 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminimum snap beading screws etc., complete all as specified and directed.(Note: Provn of AC duct to be provided for windows)

Supply and fixed in repairs 300mm ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and fixed in repair 100mm size, butt hinge medium weight cold rolled mild steel & fixed complete all as specified and directed.

Supply and fixed in repair 300 mm long Aluminium sliding door bolts with hasp and staple(bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium and fixed all as specified and directed.

Supply and fixed in repair for 200mm length aluminum, anodised, barrel tower bolts of extruded section and fixed all as specified and directed.

Supply and fixed in repair for 150mm length aluminum, anodised, barrel tower bolts of extruded section and fixed all as specified and directed.

Supply and fixed in repairs 150mm size aluminum handles, cast type anodised complete all as specified and directed.

Supply and fixed in repair floor door stopper 150mm size of aluminium alloy body and tongue, anodised, with hard drawn rod fixed in floor all as specified and directed.

Supply and fixed in repair for Harrison Curtain rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.in repair all as specified and as directed

Preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer.

Complete removal of existing treatment and preparing wall surfaces and applying two coats of oil emulsion distemper over a coat of alkali resistant primer.

Complete removal of existing treatment and preparing wall surfaces and applying two coats of oil emulsion distemper over a coat of alkali resistant primer over 2mm thick wall care putty all as specified and as directed.

Preparation of old surfaces including washing, rubbing down and stopping of distempered and painted surfaces and applying one coat of oil emulsion distemper on wall all as specified and as directed.

Preparation of old painted surfaces of steel and iron of any description over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and as directed.

Preparation of old surfaces including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots on wall/ceiling and applying one coat of white wash all as directed.

Taking up or down steel water tubings and connections of 25mm bore pipe including cleaning or re-fixing or removal to store , complete all as specified and directed.

Unplasticised PVC pipes 15mm bore of pressure rating 10kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and as directed.

Unplasticised PVC pipes 20mm bore of pressure rating 10kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and as directed.

Unplasticised PVC pipes 25mm bore of pressure rating 10kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and as directed.

Supply and fixed in repairs 15mm bore Pillar taps bore cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe, complete all as specified

Supply and fixed in repairs 15mm bore stop valve/Angle cock, chromium plated fancy type cast copper alloy, screwed down high pressure, with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed of,complete all as specified and directed.

Supply and fixed in repairs 15mm bore Bib taps, cast copper alloy chromium plated with crutch or butter-fly handle screwed down, screwed for iron pipe or for brass ferrules, complete all as specified and directed.

Supply and fixed in repair 15mm bore brass CP mixer for mixing hot & cold water, screwed down for iron pipe and fixed, complete all as specified and directed.

Supply and fixed in repairs 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 142gms) complete all as specified and directed.

Removing plants, weeds etc., on chajjas, roofs, walls at any position and at any situation of height upto and including 03 storeys/10m, RCC roof parapets and sparying weed controlling chemical using glyphosate or equivalent in dosages as per manufacturers & all as specified and directed.

1000 ltr capacity rotational moulded polyethylene water storage tanks (Cylinderical vertical with closed top) and fixed in position, all as specified in SSR Part-I, including dismantling of old water tank of any description, complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks capacity exc 500 and n.exc 1000ltr and from mouths of circulating pipes, etc.,all as specified and directed.

Supply and fixed in repairs PVC connection 15mm size with PTMT nuts of length 600mm,complete all as specified and directed.

Supply and fixed in repairs 125mm Chromium plated shower roses with or without swivel joints, including fixing to steel pipe or union

Supply and fixed in repairs 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe , all as specified and directed.

Supply and fixed in repair Lid for rotational moulded polyethylene water storage tanks (any capcity) complete all as specified and directed

Supply and fixed in repairs Tubular towel rail, brass chromium plated 20mm dia D type, 60cm long between flanges, complete all as specified and directed.

Supply and fixed in repairs only brass chromium plated Health Faucet with 1mtr Flexible tube & Hook (Make Prayag or equivalent) complete all as specified and directed

Supply and fixed in repairs Sheet glass shelf assembly consisting of 5.5mm thick, 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and as directed.

Supply and fixed in repairs Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

Supply and fixed in repair Vitreous China wash down water closet pan (pedestal pattern) white(excluding flushing cistern and flush pipe) including connection to drain or out going pipe and flush pipe anti symphonize pipe etc complete all as specified and as directed.

Supply and fixed in repairs Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern including all joints all as specified and as directed.

Supply and fixed in repairs 32mm Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm- 45gms) all as specified and as directed.

Supply and fixed in repairs PVC waste pipe 32mm bore all as specified and as directed.

Supply and fixed in repairs Grating doom 100mm dia of PTMT (Minimum weight 25gms) all as specified and directed.

PVC (SWR) pipe 110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed.

PVC (SWR) pipe 75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints,fixed to walls, complete all as specified and directed.

Virified ceramic tiles 10mm thick light shade (Square/rectangular) polished, area of each tiles n.exc 0.36 Sqm, in floors over 15mm thick screed bed in CM 1:6 on floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed.

Vitrified ceramic tiles 10mm thick light shade (Square/rectangular) polished, area of each tiles n.exc 0.36 Sqm, but in vertical surface (dado/skirting) to match the shade of floor tiles laid over and including 10mm thick back coat in CM (1:3),complete all as specified and directed.

Non - skid Coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

Non - skid Coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,on vertical surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and incl backing coat of in CM 1:3 10mm thick complete all as specified and directed.

Granite of any (type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement and admixture of pigment to match the shade of granite stone including grinding and polishing and 20mm thick rendering in CM 1:6 on brick work or concrete surface incl demoliting complete all as directed

M/s Omm Muruga Enterprises (BID ID -3132697)

pmv.enterprises (BID ID -3140417)

SAMYDOSS CONSTRUCTIONS (BID ID -3127692)

S K ENTERPRISES (BID ID -3133117)