REPAIRS TO CERTAIN DAY TO DAY MAINTENANCE WORK INCLUDING PLASTERING BRICKWORK CEILING SAFETY RAILS DOOR STOPPER COMMON AREAS INSIDE HOSPITAL BUILDING UNDER AGE I ASVINI

Amount

Taking down cement plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and rubbish off the premises. Note: The place of disposal shall be find out by the contractor.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces of any description in CM (1:4)with Ready mix plaster mixed with integral water proofing compound and finished even & smooth without using extra cement completed all as specified. (Note : WPC will be measured and paid separately)

Supply only integral water proofing compound of approved ISI make.

M&L preparing newly plastered surfaces of walls and applying two coats of Acrylic based paint exterior grade (100% Acrylic) over a coat of primer & bio wash on wall.

M&L for rendering 15mm thick in CM 1:6 on other than fair faces of bricks work or concrete finished even and smooth without using extra cement.

Material and labour for preparation of newly plastered or previously untreated surfaces of walls and applying two coats of acrylic (100 % antifungal interior grade) paint over a coat of primer etc.complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing coat) and removing rubbish off the MD premises

Material and labour for vitrified ceramic tiles 600 x 600 x 8 to 10 mm of light colour (matt finish/nano finish, double charged), polished/glazed area of each tile in floors set jointed and pointed in epoxy grout to match flooring with and including 20mm cement sand screed in cement mortar 1:6 complete. The joints shall be 2 mm thick and 2 mm thick spacer at every corner shall be used all as specified and directed.

Material and labour for glazed/ polished ceramic tiles in vertical surfaces 600 x 300 x 8 to 10 mm thick (glossy/nano finish, double charged), set and jointed using tile adhesive (3-6 mm thick) and pointed in epoxy grout to match shade of tile including 10mm thick backing coat in CM 1:4 complete all as specified and directed. Note: both the substrates should be cleaned, spread the adhesive on plastered surface and comb with a notched trowel and place the tile.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc.and removing debris out side MD land. Note: The place of disposal shall be find out by the contractor.

M&L granite (of any type) slab 18-20 mm thick machine cut in floors, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete and including 20mm thick screed bed in CM (1:6) complete all as specified and directed by Engineer In Charge

M&L granite (of any type) tiles 12 mm thick machine cut, in skirting/ dado etc. vertical surfaces laid over cement screed, and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete and including 10mm thick backing coat in CM (1:4) complete all as specified and as directed by Engineer In Charge

M&L Machine cut Kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and including 20mm thick screed bed in CM(1:6) complete all as specified and as directed by Engineer In Charge

Ditto all as per item No 13 but in riser of steps, skirting, dado and pillar etc including 10mm thick backing coat in CM 1:4 complete as directed

M&L 75mm thick PCC type D-2, (1:4:8) using 40mm graded stone aggregate as in sub base complete all as specified and directed

Material and labour for granite slabs, 18 to 20mm thick, table rubbed and polished fixed independently to walls duly supported with partition walls, as directed at site.

Taking down old aluminium framed windows/door/partion including glass/ply/particle board/floor spring/pivot at any description and in any position and refixing in the same position with repairing damaged parts complete all as specified and directed by Engr-in-charge (aluminium sections and fittings required for the reapir shall be measured and paid seperately)

S&F Extruded aluminium alloy handles, fabricated type., anodised in 150mm size

S&F in repair Extruded aluminium alloy handles, fabricated type., anodised in 150 mm size

S&F SS butt hinges medium weight cold rolled stainless steel of size 100mm

S&F in repairs SS butt hinges medium weight cold rolled stainless steel of size 100 mm

S&F alumn anodized barrel tower bolt of extruded section & fixed of size 150mm

S&F in repair alumn anodized barrel tower bolt of extruded section & fixed of size 150mm

S&F alumn anodized barrel tower bolt of extruded section & fixed of size 100mm

S&F in repair alumn anodized barrel tower bolt of extruded section & fixed of size 100mm

S&F aluminium anodised DECO grill,DG-104 fixed with necessery U/F/H channel including taking down and refixing the window etc complete all as directed by Engr-in-charge.

S&F in repairs solar control film 50 mic reflective type sticked to glass panes icluding cleaning the glass as per instructions of manufacturers

S&F in repair 8mm thick 600x600mm size gypsum prelaminated tiles false ceiling on aluminium anodized snap grid of size 605 mm x 605 mm with aluminium anodized angle 20 mm x 20 mm x 1.2 mm fixed to wall along the perimeter of ceiling with the help of nylon sleeves & screws, at 610mm centres and main and cross tees of size 31.75 mm x 31.75 mm x 1.6mm & 25.4 mm x 25.4 mm x 1.22 mm respectively with ceiling cleats / angle brackets of size 15 mm x 15 mm x 1.5 mmincluding 4 mm dia.G.I.wire suspended from the soffit at 1220 mm centres (upto 1200 mm length maximum) fixed to roof slabs by means of 12 mm dia fancy type steel anchor fastner hook 80 mm long complete all as specified and directed.

S & F in repairs 18/ 19mm thick plywood grade BWR fixed with screws including fixing and polishing teakwood beading 4mm thick to exposed sides, as in cupboards, shutters etc wherever required including necessary fixing arrangements as directed by Engineer in Charge.

S & F in repairs 12mm thick plywood grade BWR fixed with screws including fixed with screws/teakwood beading/aluminium beading to wooden or Aluminium frame work etc.complete all as specified and directed.

M & L 0.9 mm decorative acrylic laminate type 1 of surface finish , colour and pattern as approved, fixed with approved adhesive as per manufacturer's instruction

Taking down old aluminium framed windows/door/partion including glass/ply/particle board/floor spring/pivot at any description and in any position complete all as specified and directed by Engr-in-charge

Supply and fix powder coated aluminium sections of various sizes required for frame and shutters of doors, windows, ventilators and partition with one or more rebates etc.including necessary joining cleats, glazing clips, beading, rubber packing, screws and all other fittings like locking arrangement for shutters etc. complete all as specified and directed. Notes:- (i) Glazing/wire mesh shall be measured and paid separately. (ii) Item shall be paid as per the weight of aluminium section however the rate quoted shall be inclusive of the cost of neoprene beading, glazing pins, screws, handle,hinges,locking arrangement ,towerbolts etc which shall not be measured for arriving the weight

S & F sheet glasses,plain 4.80mm to 5MM thick glazing all with aluminum beading, glazing pin etc, or with oil putty in square n exc .5 sqm in each pane

.-do-- all as above item No 34.00 above but exc 0.5 sqm in each pane

S&F in repairs Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg with Aluminium (Die cast) body

S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed.make: hyper, hardwyn of model as per site requirement

S&F in repair aluminum anodoised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts etc complete of size 300mm

S&F in repair SS hasp and staple including bolt to hinge plate and fixed with screw complete all as specified and as directed

S&F in repair 140 mm overall length floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor all complete as specified and as directed by Engr-in-Charge.

S & F in repairs aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperature 1.40mm and fixed with almn wire staples and rubber beading /U section if requires including taking down old windows and refixing in same position complete all as specified and directed

S&F in repairs anodized aluminium framework for doors, windows, ventilators with one or more rebates including jointing cleat for fixing and all fittings, etc. complete all as per existing pattern and directed

Supply and fix plain aluminium sheeting 0.71mm thick alloy 31000 H4 in shutters ,crumple joint including fixing to aluminium frame work with rivets etc. complete all as specified and directed.

Material and labour for preparation of old plastered surfaces of wall by washing and rubbing down and stopping of old surfaces and complete removal of existing treatment and applying two coats of acrylic (antifungal) paint interior grade over a coat of primer etc. complete all as specified and directed.

Material and labour for preparation of old plastered surfaces of ceiling by washing and rubbing down and stopping old surfaces/painted surfaces and complete removal of existing treatment and applying two coats of acrylic (antifungal) paint over a coat of primer etc.complete all as specified and directed.

Material and labour for preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of antifungal synthetic enamel paint etc.complete all as specified and directed.

M & L for mirror polishing to the existing stone flooring of any type to give high gloss finish with machine evenly with fine granding ( Fine Grade No. 120) and finally oxalic acid shall be dusted over the surface at the rate of thirty three (33) gms. per square metre sprinkled with water and rubbed hard with pad of wooden rags and floor shall be wiped with a moist rag and dried with a soft cloth and finished clean including pointing of joints with cement slurry mixed with pigment to match the colour of slab complete all as specified.

Supply and fix in repair plain ceiling system consisting of 600 mm x 600mm tiles (As per IS: 2095-1996: Part I) of pre coated galvanised aluminium in 0.7 mm thickness in required colour to be laid “on Armstrong/Hunter Duoglas grid systems/equivalent make with 15 mm wide T - section flanges in required colour having rotary stitching on the 1200 mm & 600 mm cross tees. The grid should be GI of make “Armstrong/Gyproc /equivalent make ”with 15mm wide T - section flanges in required colour shade having rotary stitching on all T sections i.e. the main runner, 1200 mm & 600 mm. Tees with a web height of 32 mm. Perimeter trim to be Armstrong/Gyproc /equivalent make as specified in List of makes of PS hereinafter, wall angles of size 19x19mm, secured to walls at 450 mm maximum centres including necessary fitting and 4 mm b GI suspenders fixed to slab using 12 mm dia fancy type steel anchor fastner hook 80 mm long in ceiling all as specified and directed.

M&L for 10 mm thick interlocking laminated wooden flooring on 2 mm thick foam sheets/adhesive as per manufacturer instruction of branded manufactures including proper levelling of base shall be done before laying including filling holes with cement plaster in CM (1:3) to made for true level. including skirting complete all as specified and directed by Engr-in-charge. Note : The colour and pattern of tile should be approved by Engr-in-charge.

Supply and fix in repair health faucet with flexible pipe(ABS Body) with 01 meter long PVC tube and wall hook complete all as specified and directed.

Supply and fix in repairs table top ceramic wash hand basin coloured vitreous china oval shape and of size 610x460x150mm.

Supply and fix in repair white vitreous china urinal (full stall type) flat back, (same as existing) with cast iron hangers, 15 mm dia CP spreader, 32 mm dia CP brass domical white for connector to 32mm dia cast bottle trap including cutting and making good the wall and floors whereever required complete all as specified and directed.

Supply and fix in repair PVC waste pipe 32mm bore, 90cm long fixed with waste coupling complete all as specified and directed.

S&F in repairs 15 mm bore Florentine Pillar Cock with Extended Lever Handle cast copper alloy chromium plated complete all as specified.

S&F in repairs 15 mm bore Florentine Bib Cock with Extended Lever Handle and Wall Flange cast copper alloy chromium plated complete all as specified.

S&F in repairs toilet paper holder complete all as specified.

Demolition of brick work or stone/boulder masonry, built in cement mortar, including all quoins, arches, pillars, shaft walls, crumple edges and supports for water pipeline carefully including copings etc.and removing debris outside MD land complete all as specified.Note: the work to be carried out in roof of G+6 storey bldg

M&L for brick work with sub class 'B' bricks(Old size), straight or curved on plan exc 6m mean radius built in cement mortar (1:4) complete all as specified.

M&L brick work with sub class 'B' old size bricks(half brick thick wall), straight or curved on plan exc 6m mean radius built in CM 1:6 including duly reinforced with 10 mm dia MS round bars 2 nos horizontally after each 4 layer of bricks complete all as spd and directed

Supply and fix wall mountained stainless steel hand rail of 30 to 40 mm dia with hinge including all necessary fittings complete all as specified and directed.

jkconstruction (BID ID -3464065)