REPAIR/ MAINTENACE OF FLOORING,JOINERY, SANITARY FITTINGS AND CONNECTED ITEMS AT OFFICE COMPLEX AND OTM ACCOMMODATION AT SQAE (SA) KANPUR UNDER GE(I) (P) FY KANPUR

Amount

Dismantling, floor, hearth or wall tiling including CM(bedding (but not backing), removing serviceable tiles to store & rubbish off the premises

Dismantling framed timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, in any position

Demolition of Brickwork or stone/boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles

Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sq. m each, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 & n exc 4 sq. m each, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

Demolition of cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) all as specified and directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over 20 mm thick CM 1.:4 screed laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete

M&L scaraping old surface removig loose meterials and apply 50mm thick PCC 1:3:6 type C-2 (using 20mm graded stone aggregate) as in path finish even & smooth without using extra cement all as specified and directed.

M&L Scraping old surface removing loose material and apply 75mm thick PCC type B-2, (1:2:4) using 40mm graded stone aggregate

M&L 100mm thick PCC type C-2, (1:3:6) using 20mm graded stone aggregate

Excavating over areas, n exc 1.5m deep & getting out in soft / loose soil

Removing excavated soil exc.1.5km & depositing where directed at a level n exc. 5 km above the starting point

Sand filling under floors or in range area including watering & consolidation

M&L for 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for vtrified jointfree printed coloured tiles 10 mm thick (square/ rectangular) double charge area of each tiles exceeding 0.42 Sqm but not exceeding 1.00 Sqm as in floors etc; set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tile complete all as specified and directed.

M&L for vtrified jointfree printed coloured tiles 10 mm thick (square/ rectangular) double charge area of each tiles exceeding 0.42 Sqm but not exceeding 1.00 Sqm as in Verticle surface etc; set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade over and including 10mm thick cement sand screed in CM 1:3 complete all as specified and directed.

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:4)

S&F Coloured Glazed ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.14 sqm, in verticle etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick screed in CM(1:3)

S&F in repair Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC Sheet & edges will be painted to match with prelam sheet reinforced with M.S Square tube, in opening as per specification & drawing

M&L for factory made solid pvc profiled panel door shutter 28mm thick with integral skin as frame & 3mm thick high pressure compact laminated on bothsides of approved colour as in fill with C type GI or 40x20x19 of ms pipe as in stiffner & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F in repair Rotational moulded polyethylene water storage tanks white colour (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white including flush pipe sistern PVCConnection etc Complet all as per specified and directed.

S&F in repairs Vitreous China Urinal, Half stall type, white including flushing sprader flush pipe & waste pipe etc Complete as per specification and directed.

S&F in repairs PVC valveless, syphonic action type, flushing cistern 10 litr capacity, low level, white, with intel, ball valve, float & handle including brackets

S&F Stainless steel Butt hinges 100mm size, extruded brass,with mild steel hinge pin, bright polished, type B-11

S&F Brass barrel tower bolts with cast or sheet barrel and rolled or cast bolts 150mm long of extruded section.

S&F Brass handles 125mm size, cast type, polished bright

S&F Brass, sliding door bolt 200mmlong with sand or die-cast brass hasp, staple (bolt type) & fixing bolt with rolled or drawn brass bolts.

S&F 140mm long Floor door stopper of brass body & tongue with hard drawn steel spring.

M&L in repairs vitreous china WHB white flat back size 550x400mm incl with angle iron brackets, cp pillar trap fency type 01 no 15 mm bore cp waste coupling 32 mm dia and pvc waste pipe 32 mm dia pvc connection 450 mm long all as specified

Hacking out old broken glass (any thickness, size, quality or description) from wooden or steel frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F of 3 mm thick sheet glass, ordinary quality and glazing with putty or fixed with beads in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F in repair Aluminium anodised Tubular towel rail 20mm dia

S&F in repair Aluminium chromium plated brackets

M &L Brickwork with subclass 'B' old size bricks, straright or corved on plan exc 6m mean radius built in Cement mortar 1:6 complete all as specified and directed.

M&L for Cleaning with epoxy cloth and exposed corroded re-bars by chiseling out enough cavity to access entire dia of correded bars and applying anti corrosive chemical to the reinforcement. ( Chemical any of the manufacturer :- Tuffshield combine Pvt. Ltd / Fosroc / Sika / Pedilite / or Mc Bauchemie )

M&L epoxy based bonding material for bounding old concret surface to new morter ( Chemical any of the manufacturer :- Tuffshield combine Pvt. Ltd / Fosroc / Sika / Pedilite / or Mc Bauchemie )

M&L 20mm thick morter using high flexural and high tensile strength polymer chemecal as dubbing coat rough finished all as specified and directed.( Chemical any of the manufacturer :- Tuffshield combine Pvt. Ltd / Fosroc / Sika / Pedilite / or Mc Bauchemie )

M&L Rendering 5mm thick on fair faces of concrete surfaces in CM (1:3) in ceiling

Applying three coats of white wash on new ceiling surface including preparation of surface.

M&L for plain cement concrete (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in roof kerb, copings water troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing complete GDE Fe410-0 or Fe 310-O

Dismenteling wrought iron or mild steel works of any description not other wise provided for.

Supply & fixing Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing complete GDE Fe410-0 or Fe 310-O

S&F Mild steel, plain black sheet 1.25mm thick in , steel gates & similar work, cut to size, holes punched; including round headed screws, clout nails or rivets & fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 including mixing of water proofing compound as directed.(Note : water proofing compound will paid and measured separately) completed all as specified and directed by Engr-in-charge.

Supply only integral water proofing compound completed all as specified and directed by Engr-in-charge

M&L Rendering 15mm thick on stone masonry surfaces or surface other than fair face of brickwork in CM (1:6)

M&L for two coats of exterior emulsion (weather coat/ appex) on prepared surface complete all as specified and directed.

M&L for prepration of surfaces by applying jk/birla wall care putty and rubbing &making the surface smooth by using embray paper complete all as specifird and directed

Applying two coats of Distemper oil emulsion, white or tinted on new wall surface including preparation of surface.

Applying two coats of Distemper oil emulsion, white or tinted on old wall surface including preparation of surface.

Applying Two coat of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of old painted surface.

M&L for preparation of any steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide all as specified and directed.

Dismantling/Demolition textile covering including frame (if any) and cover fillets complete all as specified.

GI frame work for seamless ceiling comprising of gi perimeter channel 0.55 mm thick with two unequal flenges of 20 and 30 mm and web 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit 900 mm centre to centre with gi cleats and steel expansion fasteners with and incl ceiling section section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre

Providing and fixing 10mm thick plaster of paris of ceiling board(gypsum anhydrous) to flate surface over metal frame work as directed by EIC.

S & F Hanger 6mm dia GI (upto 1200mm lenth) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flats 40 X 3mm size 60mm long complete all as specified.

M&L for plain cement concrete 1:2: 4 type B1 (20 mm graded stone aggregates) on roof kerbs or mud stops, rounded or chemfered completed all as specified and directed by Engr-in-charge

M&L Hardcore of Broken stone/boulders gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface

S&F in repair vitreous china wash down cascade closet with P trap of make Parryware (Kalhari closet set P/S) MAKE: PARRYWARE (Cat part No.Closet(S/P)-C0232/286, Cistern- C0711, Cistern lid- C2054, Ultra solid cover-C8140, Floor mounted fittings-C8016)

S & F in repair 15mm bore bib cock, with wall flange, chromium plated as fixed in repairs, complete all as specified and directed.MAKE: JAQUAR (Cat part No.FUSION 29037)

S&F in repair CP concealed stop cock entire heavy body with adjustable wall flange size 15mm MAKE: JAQUAR (Cat part No.FUSION 29037)

S&F central hole basin mixture type MAKE: JAQUAR (Cat part No.QQT-7167B)

S&F CP angle valve 3 in one 15 mm dia Make : Jaquar

S & F CP hand shower (Health Faucet) with 8mm dia, 1 metre long flexible tube with wall hook, complete all as specified and as directed.MAKE: JAQUAR (Cat part No.ALD-573)

Cutting chases in brick wall for concealed pipes n.exc100mm girth and making good with PCC or cement mortar after fixing of pipes complete

Supply and fixed half stall urinal parryware with automatic flush (censored) and connection to pipes and fixing of lever if any including flushing pipe PVC.Make: PARRYWARE ( Urinal Cat part No. C0503, Electronic flushing system Cat part No.C8132)

Supply and fix looking mirror ornamental type of size 900mm x 600 mm with iron decorative frame(Parryware).

S&F cascade shelf soap dish fixed to wall with and including chromium plated brass screw . Make : JAQUAR Cat No - 1131N

S&Fliquid soap container fixed to wall with and including chromium plated brass screw . Make : JAQUAR

S&F Brass chromium plated towel rail 24" fancy type Make : JAQUAR (CAT NO : 1181)

S&F of glass shelf assembly consisting of 5.5 mm thick glass shelf 12 cm wide with chromium plated guard and railing 60 cm long (Make : JAQUAR). Cat No 1171N

Supply and fix stainless steel toilet paper holder box type fixed to wall with and including chromium plated brass screws Make : JAQUAR Cat No : 7753

M&L in repairs for vitreous china white wash basin table topedge 65 R Make Jaquar cat no 91101 size65x45x11.5 cm with all necessary fitting anf fixtures including cp brass wash basin mixture cat no F-20001 Make hindware/Equivalent

S&F 110mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls.

S&F 110 mm PVC (SWR) branch piece, single (Single 'Y' equal or unequal).

S&F PVC(SWR) bends 110mm dia any radius.

S&F GI Tubes, `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 20mm bore including taking up or down steel tubing & connections

S&F GI Tubes, `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 15mm bore

Taking up or down 15mm bore dia, steel tubing & connections incl cleaning for refining as dircted.

Taking up or down for 20mm bore steel water tubing galvanised with connection complete all as specicfied.

Taking down and Refixing shutters exc 1.50 Sqm but n.exc 4 Sqm each as directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F in repair mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F IInd class hard wood plain, solid, straight chowkhats and frames wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints as directed.

M&L for preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified.

S&F in repair framed work such as grills, gratings, etc; with ends of bars shouldered and or riveted, or forged into spikes; framed guard bars; barred iron doors, ladders, framed balusters; walk ways; railings; framework of watertanks and similar work conforming to Fe-290 Gde-E-165 including welding complete all as specified and directed.

Demolition of reinforced cement conc any position.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to complete all as specified and directed.

M&L for formwork to sides and soffits of lintels including supports, overhangs, etc also splays between floors and beams, etc rough finished surfaces of concrete flat complete all as specified and directed.

S&F in repair 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides.

S&F in repair steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded.

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment over over 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

S.D.TRADERS