PROVN OF PATIENTS CLOTHING STORE, STORAGE ACCN FOR GAS CYLINDER, RATION STORE OF HOSPITAL AND DRAIN FROM BLDG NO T-649 TO T-294 AND INCINERATOR AT RHENOCK UNDER GE 867 EWS

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft / loose soil, complete all as specified and as directed.

Excavation in trenches n exc 1.50m wide and not exc 1.50m deep for foundation and getting out in soft / loose soil, complete all as specified and as directed.

M&L Returning filling in, including spreading, levelling, watering and well ramming in layers not exc. 25cm in soft / loose soil fIlling under floor, complete all as specified and as directed.

Removing excavated material not exc 50m and depositing where directed at a level not exc 1.50m above the starting point, complete all as specified and as directed.

M&L PCC type D-2 (1:4:8) (using 40mm graded crushed stone agg) in foundation filling and mass concrete, complete all as specified and as directed.

M&L for PCC type C-2, (1:3:6) (using 40 mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified and as directed.

M&L 75 mm thick PCC type C-2 (1:3:6) (40 mm graded crushed stone aggregate) for plinth protiction, path/ steps etc to be finished fair and even, complete all as specified and as directed.

M&L precast cement concrete type C-1 , (1:3:6) (using 20mm graded crushed stone aggregate) block masonry with solid blocks 10cm in width and setting in CM (1:6), complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers, lintels, cantilevers, shelves including supports, overhangs,etc. also splays between floors and beams, etc. for rough finished surface of flat concrete, complete all as specified and as directed.

M & L Reinforced cement concrete (Nominal mix ) type B1 (1:2:4) (20 mm graded crushed stone aggregate) as in Beams, cantilevers, shelves, bressummers, lintels over 1.5m span, complete all as specified and as directed.

M&L mild steel deformed bars 10mm dia and over cut to length bend to shape required incld cranking bending spirally for hooping for column, hooking ends and binding with and incld mild steel wire (annealed not less than 0.90mm dia or securing with clips, complete all as specified and as directed.

Ditto as per sl item No-11 above but 5mm dia and over upto and incld 10mm dia in stirrups, spacer and binders, complete all as specified and as directed.

M & L 15mm thick rendering on fair faces of brick work or concrete surface in cement mortar (1:6) complete all as specified, complete all as specified and as directed.

M&L preparation of new plastered surfaces of walls and applying two coat of oil bond distemper over a coat of chalk whiting complete all as specified, complete all as specified and as directed.

M&L 20mm thick rendering in two layers of 10mm each on brick or block concrete masonry walls in cement mortar (1:4) with WPC incl finished even and smooth w/o using extra cement, complete all as specified and as directed.

M&L for applying two coat of cement base paint over a coat of primer including preparation of newly plastered surfaces.

S&F for rolled section as in main and cross beams hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angles cleats or other connecting plates in FE-410W (Gde E-250) quality A, complete all as specified and as directed.

S&F Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with seif tapping screws complete all as specified and as directed.

S&F pre-painted galvalume aluminum zinc coating GI plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as in ridge , complete all as specified and as directed.

M&L hardcore of gauge exc 63mm but n exc 100mm,deposited, spred and levelled in layers n exc 15 cm thick watered and rolled /rammed to a true surface, complete all as specified and as directed.

M & L for 100 mm thick cement concrete type D-1,(1:4:8) (40 mm graded crushed stone aggregate) as in sub base or sub flooring fininshing the surface even and rough to receive the topping layer, complete all as specified and as directed.

M & L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 15 mm thick screed bed or bedding layer of cement mortar (1:6), complete all as specified and as directed.

M & L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed including 15 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and as directed.

S&F GI frame work of size 605 x 605mm, for seamless celing comprising of GI perimeter chanel 0.55mm thick with two unequal flangesof 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and incl ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre, complete all as specified and as directed.

S&F hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasterners 12.5mm dia 40mm long, complete all as specified and as directed.

M&L for 4 mm thick E Board (Everest) non combustible moisture resistant plain building boards, fixed to timber/GI aluminium frame work with screws as in ceiling, complete all as specified and as directed.

M&L for preparation of newly ceiling surface and appliying of three coats of white wash, complete all as specified and as directed.

S&F Pressed steel door frame for doors, size 125 x 60mm with one rebates incl necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and as directed.

S&F 40mm thick factory made flush shutters,solid core construction ,with block board core and ply wood face panels,commercial type on both side face is cover with decorative face veneer with lipping/ frame to match, complete all as specified and as directed.

S&F Steel windows with side hung shutters incl projecting type hinges with steel handle, and steel peg stay complete with glazing bars, complete all as specified and as directed.

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; and similar work conforming to Fe.290.Gde-E-165, complete all as specified and as directed.

S&F 3mm thick sheet glass, oridinary quality and glazing with oil putty in square n etc 0.5 sqm in each pane, complete all as specified and as directed.

M&L Preparation and applying two coat of synthetic enamel paint over one coat of red oxide primer on new steel surfaces, of any description, over 10cm width or girth not other wise, complete all as specified and as directed.

M&L Preparation and applying two coat of synthetic enamel paint over one coat of pink primer on new wooden surfaces, of any description, over 10cm width or girth not other wise, complete all as specified and as directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded sections, complete all as specified and as directed.

S&F 150mm long aluminium handle cost type anodised, complete all as specified and as directed.

S&F 300 mm long aluminium alloy, anodised sliding door bolt with hasp and staple (bolt type ) and fixing clip of sheet cost or extruded section or cost aluminium alloy & fixed, complete all as specified and as directed.

Form work to sides of concrete foundations, footings, bases of columns and plinth beam and similer work etc in rough finished surfaces of concrete flat, complete all as specified and as directed.

M&L for PCC type C-2, (1:3:6) (using 40 mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, complete all as specified and as directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm ditto item no-40 above, complete all as specified and as directed.

M & L preparig plastered or unplastered new surfaces of wall and applying three coat of white wash, complete all as specified and as directed.

M & L for mild steel framed work work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering. doors, etc with Fe 290 Gde E 165, complete all as specified and as directed.

M&L for 75 mm thick cement concrete type C-2 (1:3:6) (40 mm graded crused stone aggregate) as in floors finished even and smooth using extra cement, complete all as specified and as directed.

M & L for 75 mm thick cement concrete type D-1, (1:4:8) (40 mm graded crused stone aggregate) as in sub base or sub flooring fininshing the surface even and rough to receive the topping layer, complete all as specified and as directed.

M&L machine pressed chequered cement concrete tiles size 30cm x 30cm x 25mm thick and above, set,jointed and pointed in neat slurry with grey cement and pigments in floors cut and polished. over and incl 15mm thick screed bed or bedding layer of motar for laying floor finishes in cement plaster (1:6), complete all as specified and as directed.

M/L for Point wiring complete with 1.5 sqmm single core PVC insulated and PVC unsheathed FRLS multistranded copper conductor cable 1100 volt grade enclosed in and including PVC casing and capping with accessories fixed on surface on walls/ceiling by means of PVC sleeves, Dash fastners and cadmium plated screws including sunken junction box not less than 3.0 mm thick concealed in wall, mounting accessories like switches, sockets fan regulators with 3.0 mm thick Laminated sheet top covers etc including 1.5 Sqmm single core multi stranded copper conductor PVC insulated and unsheathed cable as earth continuity conductor to common earth dolly. for the following, complete all as specified and as directed. Make : Polycab/KEI/Plaza/Havells

All as per item No 47 here – in – before but for one 3 / 5 -pin switch socket outlet 5 amps on independent board.

All as per item No 47 here – in – before but for one switch socket outlet 15 Amps on independent board with 2.5 Sqmm multi stranded and 2.5 Sq mm stranded (for earth) PVC insulated un-sheathed copper cable, complete all as specified and as directed.

Supply and fix switch piano flush button, single pole, 5 amps, one way, complete all as specified and as directed. Make : Anchor/Havells/Plaza

Supply & Fixing ceiling rose surface bakelite 65 X 50 mm three terminal , complete all as specified and as directed. Make : Anchor/Havells/Plaza

Supply and fix switch socket combination 2 – in – one, 3 Pin / 5 Pin, 5 amps flush type, complete all as specified and as directed. Make : Anchor/Havells/Plaza

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and as directed. Make : Crompton/Havells/Philips

S & F 9W LED Bulb suitable for B22 holder . System Efficacy should be > 85 lm/ W. PF > 0.9, The Lamp Should have Cool Daylight Color temp of 6500K, lumen output >800 lm, complete all as specified and as directed. Make: Philips/Wipro/Crompton

S & F lamp holder,PVC/Polycarbonate type and back plate suitable for batten fitting, complete all as specified and as directed.

S&F Sheet metal enclouser Double door for MCB DB,s Phosphatised Powder Painted with bus bar 200 Amps rated Single pole and neutral linkof 4 way 240 Volts AC, complete all as specified and as directed. Cat Part No 5076 11 of Make- Legrand or equivalent in Siemens/Schindler.

Supply and fixing MCB Single pole and neutral 40 Amps capacity 10 KA 240 Volts 50 HZ, 'C' curve, complete all as specified and as directed. Cat part No 4086 18 of Make : Legrand or equivalent in Siemens/Schneider.

Supply and fix MCB single pole (SP), 10 kA of 5 -32 Amps capacity 240 Volts, 'C' curve, complete all as specified and as directed. Cat part no 4085 95 of Make : Legrand or equivalent in Siemens/Schneider

M&L for Sub main wiring with FRLS two single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 4.0 Sqmm size drawn through and including not less than 25/16 mm PVC cashing & capping medium grade ISI marked and conduit junction boxes, terminal boxes and incl all accessories fixed to the surface of wall/ceiling including one run of 4.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor, complete all as specified and as directed. NOTE : Two runs of single core 4.0 sqmm and one run of 4.0 sqmm copper FRLS cable as earth continuity conductor and suitable size cashing & capping with accessories shall be measured as one length.

M&L for Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm buried directly in ground ( earth pit not less than 2.25 m deep bellow ground level ) with top edge of the plate not less than 1.5 m bellow normal ground level, connected to galvanized earth lead wire 4 mm dia. by means of galvanized iron or steel bolts , nuts , check nuts and washers, and connected to equipments as directed , including funnel with GI med grade watering pipe 20 mm bore , wire mesh , charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode , with concrete pit in PCC (1:3:6) type C-1 , 50 mm thick pre cast RCC (1:2:4) type B-1 cover slab reinforced with 8 mm dia deformed bar 15 cm C/C and suitable handle of 10 mm dia round bar ,GI medium grade pipe for earth lead protection including necessary excavation earth work in soft/loose soil and disposal of spoil to a distance n.exc. 50 m and necessary testing complete all as shown on electrical plate No. 3 of MES SSR Part-I, complete all as specified and as directed.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amps, 240V, complete all as specified and as directed.

Note: In case doubling/duplicancy of BOQ items , the lowest quoted rate shall be applicable for payment.

SANJAY SAW MILL

DEEP CHANDRA JOSHI

RAMESH GURUNG

MANOJ JINDAL

HEM RAJ GURUNG

M/S JAYSHREE CONCERN

SANJAY MITTAL