COMPREHANSIVE MAINT OF EM AND BR SERVICES TO CERTAIN BLDGS IN CERTAIN OTM ACCNS OF INS ABHIMANYU AND OTHER UNITS AT NAVAL STATION KARANJA

Amount

Notes : - (i) The is at Serial No 49 of TPP 2025-26 (ii) Please refer schedule 'A' notes before quoting the tender. (iii) Amount of Schedule of Credit shall be deducted off line by the department. The Unit Rate quoted in r/o Ser item No 1.00 to 2.41 are deemed to include for the following and nothing extra will be paid for these works: 1. Supplying, erecting and use of scaffolding upto required height (max 25 to 30m) or upto 8th floor height with necessary H-frames, pipes, couplers, buckles, bracing, top platform with support railing at top etc. at all levels of building including carriage of the materials to the location, erecting, fixing the scaffolding and dismembering the same after working and taking away the scaffolding materials etc. complete as per direction of Engineer-in-charge. 2. Supplying, erecting & use of temporary bamboo scaffolding around the building as required. The scaffolding is to be secured properly in position by bracings, ties clamps, etc. complete including providing and erecting working platform at all heights as required, including removal after completion of work all as per direction of Engineer-in-Charge

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specifedand directed

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

S & F steel work as in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS 1161 1979 grade St 240 complete all specified and directed.

S&F rolled sections of Fe 410W (Gde-E-250)as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all specified and directed.

S & F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all specified and directed.

Supply & fixing of framed work such as grills, gratings, cooler stands etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165 incl necessary fixing to walls as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismanlting of old Sheet etc complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of old sheet etc complete all as specified and directed.

Excavating post hole ( or similar holes each exc 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around with earth around in layers not exc 25 cm thick in any type of soil complete all specified and directed.

M&L for cement concrete C-2 1:3:6 using 40mm graded crushed stone aggregate stone aggregate as in foundation, filling and mass concrete, in fencing pole complete all as specified and directed.

Preparation of new previously untreated steel and iron surfaces of any description not other wise described over 10 centimetre width or girth and M&L for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome complete all as specified and as directed.

S&F, PVC False ceiling consisting of 600 mm x 600 mm, 8-10mm thick prelaminated hollow self design including frame work made using aluminium T section of size (25mm x 25 mm, 19 gauge or 1mm thick) in square pattern of grid size of 600 x 600 mm. The aluminium frame work is supported from the ceiling with the help of 2 mm dia GI wire (upto 1200 mm length) adjusting and maintain for proper level to roof slabs by means of ceiling cleats made out of GE flat 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete etc. The aluminium frame work is supported on side wall with the use of aluminium 25 mm X 25 mm angles including taking down of old Ceiling frame and board complete all as specified and directed. (Note:- Item rate shall be include upto 30 meter of height of Bldgs for scafolding as all arrangement.)

S&F, in repairs 8 to 10mm thick PVC false ceiling consisting of 600mm x 600mm Hollow prelaminated self design insert existing frame work without disturbing the other false ceiling and making good existing frame complete all as specified and directed. (Note:- Item rate shall be include upto 30 meter of height of Bldgs for scafolding as all arrangement.)

S&F false ceiling with Armstrong XL 24mm grid system of grid size 600x600mm with 14mm thick ceiling board of RH-90. Grid shall be suspended from ceiling using 2mm dia pre straighten GI wire with 6mm nylon rawl plug & screws at 1200mm intervals including taking down old frame nad ceiling board complete all as specified and directed. (Note:- Item rate shall be include upto 30 meter of height of Bldgs for scafolding as all arrangement.)

S&F, in repairs 8 to 10mm thick Armstrong ceiling board of RH -90 false ceiling consisting of 600mm x 600mm insert existing frame work without disturbing the other false ceiling and making good existing frame complete all as specified and directed. Note:- Item rate shall be include upto 30 meter of height of Bldgs for scafolding as all arrangement.)

S&F in repairs to 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame complete all as specified and directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame including taking down of old wall panelling complete all as specified and directed.

S&F of decorative Hollow PVC sheet 10 mm thick (fluted panel) having density not less than 4 Kg/Sqm fixed to wall panelling with self drilling screws including necessary frame of aluminium section 51x35x.55mm and 600 mm c/c 51x32x.55mm grid work and corner mouldings as required as per manufacturer's instruction including taking down old Wall panelling with frame complete all as specified & direced

S&F for PVC tiles /sheets, of 2mm thick laminated plain coloured homogenous, laid with approved rubber based adhesive in floors including taking down of Old PVC tiles complete all as specified and directed.

M&L for 40 mm thick cement concrete type B-0, 1:2:4 using (12.5mm graded aggregate) as in SUB-FLOORS, SUB-BASES, FLOORS AND PAVINGS, ETC complete all as specified and directed

M & L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 20 mm thick screed bed in cm (1:6) for laying floor fineshes including dismentling of old tiles complete all as specified and directed.

M&L non skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in floors over & including screed bed or bedding layer of morar 15 mm in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including dismentling of old tiles complete all as specified and as directed.

M&L non skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in skirting/dado over & including 10 mm thick cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including dismentling of old tiles complete all as specified and as directed.

M&L for vitrified light shade tiles 8 to 10 mm thick (square/rectangular) polished, area of each tiles not exceeding .36 Sqm, in floors etc, set and jointed in neat cment slurry and pointed in white or coloured cement to match over & including 20mm thick screed bed in Cement Mortar 1:6 including dismentling of old tiles complete all as specifed and directed

M&L for vitrified light shade tiles 8 to 10mm thick (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, as in vertical surfaces such as skirting, risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over & including 10mm thick rendering in cement mortar 1:4 including dismentling of old tiles complete all as specified and directed.

M & L for Glazed ceramic coloured tiles in vertical surface 350mmx250mm x7mm / 450X350X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering or bedding layer in cement mortar 1:4 including dismentling of old tiles complete all as specified and directed

M&L for chequered cement concrete tile 30cmX30cmX 20 to 25mm thick set jointed and pointed in neat cement slurry in floor with grey cement and pigments over & inlcuding 20mm thick screed bed or bedding layer of CM (1:6) including dismentling of old tiles complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade including taking out of old tiles complete all as specified & directed .

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade including taking out of old tiles complete all as specified & directed .

Taking down old paver blocks any shape, size and thickness from the existing surface and refixing at the same place after levelling the ground by using sand caushion for maintaing camber and slope complete all as specified and directed Note:- Sand Cushion will be paid under subsequent item.

M&L for sand cushioning for laying interlocking paver block complete all as specified and directed.

M&L for 20 mm thick Granite (of any type) tiles machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over & incldung 20 mm thick Cement motar 1:4 including dismentling of oldstone slab / tiles complete all as specified and directed.

S&F for green marble 16-18 mm thick machine cut, jointing and pointing with white cement slurry over & including 20mm thick screed bed or bedding layer of mortar in CM 1:6 including dismentling of oldstone slab / tiles complete all as specified and directed.

M&L for cement concrete type D-2 1:4:8 using 40mm graded crushed stone aggregate as in foundation, filling and mass concrete etc complete all as specified and directed.

M&L for 75 mm thick cement concrete type C-1 1:3:6 using 20mm graded stone aggregate as in plinth protection finished fair even laid in bays n.exc 2m in length and joints filled with bitumen mastic 1:3 complete all as specified and directed

M&L for 100mm thick cement concrete type B-2 1:2:4 using 40mm graded stone aggregate as in path/floor finished fair even and smooth without using extra cement, laid in alternate panels of size not exc 4 sqm each including bitumen filling in joints complete all as specified and as directed

M&L for machine cut broken stone or boulders of hard core of gauge not exc 63mm , deposited,spread and levelld in layers n.exc 15cm thick , watered and rammed to a true surface complete all as directed.

M&L for 20mm thick Wearproof topping (incorporating an approved metallic floor hardner as per manfacutre's instruction) laid on concrete floors and pavings and path, and finished even and smooth (except metallic hardner) complete all as specified and directed. (Note metallic hardender & glass strips area shall be measured and paid separately).

Supply only 22 mm wide and 3 mm thick glass dividing strips as laid in floor complete all as specified and directed.

Supply on metallic hardner mix with cement concrete as per manufacture instruction complete all as specified and directed. Make :- Dr Fixit/FOSROC or equivalent as approved by GE)

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed..

M&L for pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width in type B1 (1:2:4) (using 20mm graged stone aggregate )and setting in mortar (1:6) including demolition of old PCC Block complete all as specified and as directed

M&L brickwork with sub class 'B' bricks , straight or curved on plan exc 6m mean raidus built in cement mortar 1:6 including demolition of old brick work complete all as specified and directed

M&L for brickwork reused bricks obtained from demolition vide BoQ Serial item No 1.43 above in Cm 1:6, straight or curved on olan ecl 6m mean radius including demolition of old brick work complete all as specified and directed Note:- Serviceable bricks obatined from demolition of brick work shall be re-used after cleaning etc

M&L for walling of random rubble, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar 1:6 including demolition of Old Stone masonary complete all as specified and directed.

M&L for wall is of built in cement mortar 1:6 using stone obtained from demolition vide BoQ Serial item No 1.45 above, brought upto course, ell bonded, be added and solidly hearted Complete all as specified and directed Note:- Serviceable stone masonary obatined from demolition of Stone mansonary shall be re-used after cleaning etc

M&L for raised pointing to random or polygonal rubble masonry uncoursed or brought upto course in CM (1:4) complete all as specified and directed.

M&L for raised pointing to precast concrete block masonary wall in CM (1:4) complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick/concrete surfaces with two coats i.e (10 mm thick backing coat and 5mm thick finishing coat) , finished even and smooth complete all as specified and directed. (Note:- Item rate shall be include any height of Bldgs for scafolding as all arrangement.)

M & L for rendering 10 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth complete all as specified. (Note:- Item rate shall be include any height of Bldgs for scafolding as all arrangement.)

S&F in repairs 12 mm thick Toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and directed.

S&F in repairs 30 mm dia stainless steel handle of 60 cm long and fixed to toughned glass as per manufacturer's instructions (Make- Enox or equivalent make as approved by GE complete all as specified and directed.)

S&F in repair stainless steel glass lock fixed to toughened glass as per manufacturer's instructions of (Make-Enox or equivalent make as approved by GE complete all as specified and directed)

Taking down aluminium doors shutters only and dismantling all members and reassembling the same with and including new screws, new rubber gasket, new aluminium beads & cleats of existing make and also refixng the handles & mortice lock in existing postiion with and including new screws including refixing the door shutters in same opening complete all as specified and directed.Note : If broken or unserviceable glass/aluminium wire mesh/floor spring/concealed lock is replaced same will be paid separately under relevant items.

Taking down aluminium windows shutters only and dismantling all members and reassembling the same with and including new screws, new rubber gasket, new aluminium cleats of existing make and also refixng the locks & roller in existing postiion with and including new screws including refixing the window shutters in same opening complete all as specified and directed.Note : If broken or unserviceable glass/aluminium wire mesh/floor spring/concealed lock is replaced same will be paid separately under relevant items.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site including cutting holes required for taking out existing hold fast etc. complete all as specified and as directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) exceeding 1.5 sqm not exceeding 4.0 Square Metre each , removing from the site including cutting holes required for taking out existing hold fast etc.complete all as specified and as directed.

Taking down shutter from frame exc 1 sqm but n.exc 2 sqm each including iron mongrey & removing from site complete all as specified and directed.

Taking down shutter from frame exc 1 sqm but n.exc 2 sqm each and refixing in same opening after resecuring or easing , and adjusting complete all as specified and directed by Engr-in-charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed

S& F of Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&F in repairs stainless steel tubing of 25 mm dia for curtain rod fancy type including fancy type rings and brackets (wall to wall or flush to wall) for securing to curtain rod, complete all as specified and directed

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube and edgeswill be painted to match will printed sheet fixed in opening as per specification & drawings complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tube top & bottom rail mild steel frame shall be covered with heat moulded plain colour PVC “c” channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap inserted for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the mild steel frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supplying & fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F for aluminium door/window/ventilator/partition, made out of extruded powder coated aluminium sections, with sliding or openable shutters including frame & necessary jointing cleats, glazing clips, powder coated aluminium snap beading,screws etc, complete and also including powder coated aluminium fittings such as cobra hinges, butt hinges, tower bolts, hooks & eyes, peg stays and handles including connected items,with and including making good to the disturbed portion with its original specifications complete all as specified and directed.

S&F 4 mm thick sheet glass, ordinary quality ,fixed in aluminium Door /window shutter area n. exceeding 0.50 Square Metre each pane complete all as specified and as directed.

S&F 4 mm thick sheet glass, ordinary quality ,fixed in aluminium Door /window shutter area . exceeding 0.50 Square Metre each pane complete all as specified and as directed.

S&F for concealed star lock powder coated for aluminium window fixed as per manufacturers instructions complete all as specified & as directed.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repairs to aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 4 mm thick sheet glass, ordinary quality , glazing with oil putty or with wooden beads, area n. exceeding 0.50 Square Metre each pane including hacking out old glass complete all as specified and as directed.

S&F 4 mm thick sheet glass, ordinary quality , glazing with oil putty or with wooden beads, area exceeding 0.50 Square Metre each pane incluidng hacking out old glass complete all as specified and as directed.

S&F for rubber beading suitable for fixing 4mm / 5mm thick glass in aluminium window / doors etc complete all as specified and as directed.

S&F in repairs to aluminium anodised grill of design DG 104 pattern made out of 10mm dia rod fixed with and including standard aluminium frame of F section of size 23.40mmx15.30mm & 1.4mm thick all as per manufactures instructions complete all as specified & directed.

S&F in repairs for Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other plart made of mild steel heavy duty and fixed complete all as specified and directed..

S&F in repairs floor door stopper of Aluminium alloy body and tongue, over all length of cover plate 150mm anodised with hard drawn steel spring, fixed to shutters complete all as specified and as directed.

S&F in repairs mild steel body 4 lever Mortice lock vertical type size 100mm complete all as specified and as directed.

S&F in repairs to 18/19mm thick Block boards, grade 2 quality, interior grade, commercial type, and both faces is covered with approved pattern decorative coloured laminate type 1 of 0.9mm thick, and all around side faces is covered with decorative lipping complete prepared as cup board shutter and fixed with wooden frame-work complete alll as specified and directed

S&F in repairs to Cabinet Hinges Soft Close SS 8 Crank complete all as specified and directed

S&F in repairs to 9mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screws to timber frame work complete all as specified and directed

S&F of stainless steel butt hinges size 100 complete all as specified and as directed.

S&F in repairs to stainless steel butt hinges size 100 complete all as specified and as directed.

S&F Aluminium handle, cast type anodized size of handle 150 mm complete all as specified and as directed.

S&F in repairs to Aluminium handle, cast type anodized size of handle 150 mm complete all as specified and as directed.

S&F Aluminium anodized, barrel tower bolt of extruded section, length of bolt 150 mm complete all as specified and as directed.

S&F in repairs to Aluminium anodized, barrel tower bolt of extruded section, length of bolt 150 mm complete all as specified and as directed.

S&F in repairs 15 mm bib taps cast copper alloy, screwed down high pressure chromium plated screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15 mm Angle valve stop cock cast copper alloy, screwed down high pressure chromium plated screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs 15 mm fancy type pillar taps cast copper alloy, with capstain head .chromium plated screw down high pressure, with or without lettered HOT or Cold with long shanks and fly-nuts screwed for iron pipes and fixed complete as in repair incl necessary small GI fittings.

S&F in repairs PVC flushing cistern of 10 ltrs capacity including flush pipe PVC connection etc complete all as specified and directed.

S&F in repairs white vitreous china wash down water closet pan (Pedestal pattern) with and including P or S trap, including plastic seat cover closed pattern, fixing bolt etc complete all as specified and directed.

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, of size 580 mm x 440 mm white with integral foot rest complete including provn of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe,CI trap 100 mm Bore of pipe etc complete all as specified and directed.

S & F in repairs Vitreous China Half stall urinal White complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and directed

S&F in repairs to casket type wash down water closet with seat cover , waste pipe, cistern with lid & fittings (complete set) and fixing all as per manufacturere instructions complete all as specified and directed (Make : Cat No: 92045 Hindware or equivalent as approved by GE)

S & F in repairs vitreous China wash hand basin white, flat back of size 550x400mm fixed on and with & including cast iron cantilever bracket, Waste fittings, 32 mm dia waste couping of brass,chromium plated including fixing of tap, waste fitting etc complete all as specified and directed

S&F 32mm dia PVC waste pipe for WHB and urinals complete all as specified and directed.

S&F in repairs to 15 mm dia PVC connection 450mm longwith brass fly nut complete all as specified and directed.

S&F in repairs to 15 mm dia PVC connection 600mm longwith brass fly nut complete all as specified and directed.

S&F in repairs 15 mm wash basin mixutre, single lever extended basin mixer (height 95mm ) with popup waste system with 450mm long braided hoses, chromium plated, screwed down high pressure, screwed for iron pipe etc and fixed complete all as specfied and directed.

S&F in repairs to Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repairs Tubular towel rail made of brass chromium plated , 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repairs to CP Towel rack 600mm long with lower hangers complete all as specifed and directed

S&F in repairs CP toilet paper holder with stainless steel flap complete all as specified and directed.

S&F in repairs to 15 mm bib cock two way with flange, cast copper alloy, fancy type, chromium plated screwed down for iron pipe and fixed in repairs complete all as specified and directed.

S&F in repairs to soap dish holder of bootom CP and glass holer for soap complete all as specified and directed.

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs corner glass shelf (with bracket) complete all as specified and directed.

S &F 160 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall with stock clamps including taking down of Old PVC /CI Pipe line complete all as specified and directed.

S&F for PVC (SWR) bends any radius 160mm bore complete all as specified and as directed

S&F in repairs 75mm bore PVC(SWR) bends any radius with access door complete all as directed.

S&F in repairs 110mm bore PVC(SWR) bends any radius with access door complete all as directed.

S&Fin repairs 75mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down of Old PVC /CI Pipe line complete.

S&F in repairs 110mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls including taking down of Old PVC /CI Pipe line complete.

S&F in repairs PVC (SWR) floor trap plain with grating incl jointing with solvent cement 75mm bore complete all as specified and direcetd.

S&F 15 mm bore GI tubing medium grade, galvanised with all fitting and fixed complete to walls and ceilings or laid in floors including taking down of old Pipe line complete all as specified and directed.

Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches including taking down of old Pipe line complete all as specified and directed.

Supplying and laying of 25 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches including taking down of old Pipe line complete all as specified and directed.

M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coat of oil distemper over and including 1 mm thick wall care putty, after completely removal of existing treatment complete all as specified and as directed.

Preparation of new or previously untreated plastered surfaces of walls and M&L for applying two coats of acrylic antifungal paint exterior grade paint over & including one coat of primer complete all as specified and as directed.

Preparation of new or previously untreated plastered surfaces of walls and M&L for applying two coats of acrylic antifungal paint exterior grade paint CAMOUFLAGE PATTERN over & including one coat of primer complete all as specified and as directed.

M&L for PCC (1:2:4) type B0 (using 12.5mm graded stone aggregate) in coping bed black etc including nessesary form work complete all as specified and directed.

M&L for greasing and easing in position of mild steel rolling shutters of area n.exc 10sqm each for full movement and for easy operation for shutters including taking down of old Shutter complete all as secified and as directed.

M&L for greasing and easing in position of mild steel rolling shutters of area exc 10sqm and n.exc 20sqm each for full movement and for easy operation for shutters including taking down of old Shutter complete all as specified and as directed.

M&L for greasing and easing in position of mild steel rolling shutters of area .exc 20sqm and n.exc 50sqm each for full movement and for easy operation for shutters including taking down of old Shutter complete all as secified and as directed.

M&L for Opening of rolling shutter hood cover, greasing to gears, helical spring and guide channels and refixing all accessories back in position of area n.exc 10sqm each in repairs complete all as secified and as directed.

M&L for Opening of rolling shutter hood cover, greasing to gears, helical spring and guide channels and refixing all accessories back in position of area exc 10sqm and n.exc 20sqm each in repairs complete all as specified and as directed.

M&L for Opening of rolling shutter hood cover, greasing to gears, helical spring and guide channels and refixing all accessories back in position of area .exc 20sqm and n.exc 50sqm eachin repairs complete all as specified and as directed.

S&F rolling shutter without ball bearing, thickness of laths 1.00mm including top cover, anchoring rod, hasp and staple, gear operated type with chain wheel and hand chain and primer erected in position including taking down of old Shutter complete all as specified and as directed.

S&F Steel rolling shutters, with out ball bearing, thickness of laths 1.00mm including top cover, anchoring rod, hasp and staple and erected in position as indicated,complete: push pull or manual type including taking down of old Shutter complete all as specified and as directed.

Preparing new or previously untreated steel surface of any decription over 10cm in width or girth and M&L for applying 2 coats of aluminium paint over & including one coat of red oxide primer complete all as specified and directed.

Preparing of old painted steel surface of any decription over 10cm in width or girth and M&L for applying one coat of aluminium paint complete all as specified and directed

S&F stainless steel 304 grade framed work fancy/ornamental type in Gates/ stair hosing work and other similar works including all or any type of welding, holdfast, locking arrangement, followed by buffering and polishing for smooth finish including taking down of old SS Railing/pillars complete all as specified and as directed.

S&F in repairs to 25 mm PVC float valve high pressure of PTMT with epoxy coated aluminium rod & hight density plastic ball complete screwed for iron pipe or brass furred and fixed with fittings such as (socket, nipple, union) etc complete all as specified and directed

S&F in repairs 20 mm PVC float valve high pressure of PTMT with epoxy coated aluminium rod & hight density plastic ball complete screwed for iron pipe or brass furred and fixed with fittings such as (socket, nipple, union) etc complete all as specified and directedg

S&F in repairs Gunmental, globe or gate valves 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S&F in repairs Gunmental, globe or gate valves 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S&F in repairs Gunmental, globe or gate valves 15 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning etc and hosting if required, reconneting and refixing in position capacity exc 250 and n exc 500 ltr. including Cleaning and removing all scale and dirt etc from tanks and from mouth of circulating pipes etc complete all as specified and directed

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning etc and hosting if required, reconneting and refixing in position capacity exc 500 and n exc 1000 ltr. including Cleaning and removing all scale and dirt etc from tanks and from mouth of circulating pipes etc complete all as specified and directed

E/M PORTION

Taking down carefully copper /aluminium point wiring (light, fan socket or power) through stove enamelled steel conduit/pvc conduits including complete fittings such as switches, ceiling roses, pendants, regulators, sockets,, switch sockets, electrical fittings etc removing and making good disturbed surfaces of walls/ceiling etc, all as specified and directed.

M & L concealed point wiring with 1.5 Sqmm single core, multi stranded copper conductor 1100 V grade, ISI marked , PVC insulated unsheathed cable (with approved colour code) FRLSH cable in CONCEALED PVC , ISI marked including all accessories as approved by EIC, with PVC 1.5 mm multi stranded insulated unsheathed FRLSH copper wire, ISI marked of green colour for continous earth, including sunken box made out of suitable thick and not less than 60 mm in depth GI/MS/ pressed steel terminal box to be concealed in wall, duly painted including laminated hylum/maonite sheet cover thickness 3mm for mounting of fittings like switches, sockets, fan regulators etc. fixed with galvanised screw and cup washer complete all as specified and directed. Note : Wiring to be done as per approved colour code.

One light /fan/ call bell point controlled by one switch

One 5 pin socket outlet 5 Amps on independent board

One 5 pin socket outlet 5 Amps on same board

All as per BOQ serial item no 3.02 above but One light point controlled by 2 way switch SP, 5 Amp, 240 Volts

All as per BOQ Serial item No 3.02 above but with 2.5 sqmm multi stranded copper conductor 1100 volts grade FRLSH PVC insulated sheathed cable with FRLSH PVC 2.5 Sqmm multi standard insulated unsheathed copper wire for continues earth on independent board.

M & L point wiring with 1.5 Sqmm single core, multi stranded copper conductor 1100 V grade, ISI marked , PVC insulated unsheathed cable (with approved colour code) FRLSH cable drawn in casing caping of 25 mm wide, with double locking type, ISI marked including all accessories casing caping as approved by EIC, with PVC 1.5 mm multi stranded insulated unsheathed FRLSH copper wire, ISI marked of green colour for continous earth, including sunken box made out of suitable thickness and not less than 60 mm in depth GI/MS/ prssed steel terminal box to be conclead in wall, duly painted including 3mm hylum /masonite sheet cover, for mounting of fittings like switches, sockets, fan regulators etc. fixed with galvanised screw and cup washer complete all as specified and directed. Note : Wiring to be done as per arroved colour code.

All as per BoQ Serial item no 3.08 above but One light point controlled by 2 way switch SP, 5 Amp, 240 Volts

All as per BoQ Serial item no 3.08 above but one 5 amp socket point on same board

All as per BoQ Serial item no 3.08 above but one 5 amp multi socket indepenedent

Ditto, all as per sl item No 4 hereinbefore, but using 2.5 sqmm ( nominal area) multistranded FRLSH copper conductor cable/wire & 2.5 sqmm size PVC insulated unsheathed copper conductor cable for earth continuity ( green colour) for one 5 pin socket outlet 5 / 15 Amp multi purpose independent point controlled by 15 Amp switch, SP one way, 240 Volts & Socket, complete all as specified and directed.

All as per BoQ Serial item no 3.08 above, but using 4 sqmm (nominal area) FRLSH multistranded copper conductor cable/wire for one 5/15 Amp socket point controlled by 15 Amp switch, SP one way 240 Volts & Socket, complete all as specified and directed.

M & L Point wiring with PVC insulated unsheathed electric cable 1100 volts grade, single core,FRLSH cable having multistranded copper conductor of 1.5 Sqmm nominal cross sectional area, ISI marked, drawn in existing concealed conduit with 1.5 Sqmm green PVC insulated unsheathed multistranded copper conductor FRLSH cable, ISI marked as continuous earth conductor connected to earth dolly by providing suitable lugs including 3.0 mm new laminated hylum sheet /masonite sheet cover cover of min thick , ISI marked of Make" Hylem" of suitable sizes to be fixed/ mounting on existing MS/ GI sunkun boxes for mounting of fittings like switches, sockets, fan regulators etc fixed with galvanised screw and cup washer. complete all as specified and directed for the following. Note : Wiring to be done as per arroved colour code.

One fan/exhaust fan point controlled by one switch

One 5 pin socket outlet 5 Amps on same board

One 5 pin socket outlet 5 Amps on independent board

One light point controlled by 2 way switch SP, 5 Amp, 240 Volts

All as per BoQ Serial item no 3.02 above but with 2.5 sqmm multi stranded copper conductor 1100 volts grade FRLSH PVC insulated sheathed cable with FRLSH PVC 2.5 Sqmm multi standard insulated unsheathed copper wire for continues earth on independent board.

S&F switch piano type flush button type single pole one way 5 Amps 240V front operated complete all as specified and directed.

S&F Switch socket combination 2 in 1 3 pin, 5 A and 15Amp flush type universal complete all as specified and directed.

S&F socket 3 pin 5 A flush type.complete all as specified and directed.

S&F Bell buzzer 240v 50hz complete all as specified and directed.

S&F Bell push 240v 50 hz complete all as specified and directed.

S&Fceiling rose PVC/polycarbonate, isolated body surface Bakelite 65mm dia three terminals complete all as specified and directed.

S&F REPAIR/REPLACEMENT switch piano flush button single pole one way, 6 Amp (ISI marked) complete all as specified and directed.

S&F in repair/replacement Switch socket outlet 2 in 1, 3 pin, 6 Amp flush type (ISI marked) complete all as specified and directed.

S&F in repair/replacement Socket outlet 2 in 1, 3 pin, 6 Amp flush type (ISI marked) complete all as specified and directed

S&F in repair/replacement Switch bell push flush type 5 Amp (ISI marked) all as per complete all as specified and directed.

S&F in repair/replacement Switch socket combination outlet 15 Amp, 5-in-1, controlled by one switch (ISI marked) complete all as specified and directed.

S&F in repair/replacement Switch flush button, single pole two way, 6 Amp (ISI marked) complete all as specified and directed.

S&F in repair/replacement Socket type EME fan 5 step regulator switch/socket type for ceiling fan of suitable size, complete all as specified and directed.

S&F in repair/replacement Lamp holder/angle holder insulated body with black/white plate for batten fittings.

S&F in repair/replacement modular step type fan regulator 120 watt ,AC, 220V, 50hz ,ISI marked all specified and directed.

S&F in repair/replacement modular switch 1 module 6 amp one way ISI marked all specified and directed.

S&F in repair/replacement modular switch 1 module 16 amp one way all specified and directed.

S&F in repair/replacement modular socket 2 module universal type 5/6 amp one way all specified and directed.

S&F in repair/replacement modular socket 2 module universal type 6/16 amp one way all specified and directed.

S&F in repair/replacement modular bell push 6A 1 module complete all as specified and directed all specified and directed.

S&F in repair/replacement Bell buzzer, ding dong AC,230V, 50hz single pole complete all as specified and directed all specified and directed.

S&F in repair/replacement modular cover plates with frame up from1 /2 to 4 module as per site requirements all as specified and directed.

S&F in repair/replacement modular cover plates with frame up from 6 to 12 module as per site requirements all as specified and directed.

S&F in repair/replacement modular metal flush box as per site requirements from 1/2 to 4 modules complete all as specified and directed.

S&F in repair/replacement modular metal flush box as per site requirements from 6 to 12 modules complete all as specified and directed.

M&L for Sub main wiring with two runs of single core PVC insulated unsheathed cable 1100 volts grade, multistranded copper conductor FRLSH cable of 4.0 Sqmm (with colour code), drawn in but including non metallic rigid PVC conduit of 25mm dia/casing capping/suitable size , ISI marked including one run of PVC insulated unsheathed, multistranded copper conductor FRLSH cable of 4.0 Sqmm (Green colour) as contineous earth conductor cable connected to earth dolly in surfaces/ recess complete including taking down complete all as specified and directed.

M&L cutting of wall/ceiling/column for laying submain of any size including plastering ,white wash all specified and directed

S&F LED building security light fitting with suitable size bracket/angle with three core flexible wire to fit security light of 45 w IP 66 protection LED complete all as specified and directed. .

S&F LED batten with 20/22W LED tube light in wall/surface connecting with all required accessories like PVC box base,flexible cable from ceiling rose etc Surface and wall mounted LED batten, Engineering plastic batten with accessories complete all as specified and directed.

S&F in repair/replacement 6 to 32 AMP MCB single pole 240 V 10 KA (C-Series) complete complete all as specified and directed.

S&F in repair/replacement SPN 32 AMP MCB DP 240 V 10 KA (C-Series) complete all as specified and directed.

S&F LED recess/surface mounted 2x2 luminarie 36/40w fitting, 220 V, AC,50HZ suitable surge protection, high power factror,driver etc complete including flexible wire and connected accessories all as specified and directed

S&F LED Bulk head fittings 9/10W luminaire including LED light driver holder 220 V, AC,50HZ connecting up with three core flexible copper conductor calbe of suitable size complete with all acccessories complete all as specified and directed

S&F in repair/replacement LED tube rod 20 watt, 220V,AC,50HZ change with existing any tube rod including flexible wire and connected accessories complete all as specified and directed.

S&F in repair/replacement LED batten 10w, 2 feet with LED tube light 220V,AC,50HZ in wall/surface connecting with all required accessories like flexible cable from ceiling rose etc as directed and specified by engr-in-charge.

S&F in repair/replacement MCCB 4 pole, thermal magnetic release range 100 Amps of breaking capacity 16 kA, 415 Volts, 50 Hz, complete all as specified.

M& L for daily complaint checking & repairing of DBs/meter panel board/circuits/submain wiring/switches/sockets etc and other connected work including rectification of faults complete all as specified and directed

S&F in repair/replacement RCCBs 63 Amps double pole 100mA breaking capacity complete all as specified and directed.

S&F in repair/replacement RCCBs 40 Amps double pole 100mA breaking capacity complete all as specified and directed.

S&F decorative light suitable for holder B-22/E-27 all specified and directed engineer in charge

M&l taking out and refixing of tube light,mirror light etc after cleaning and any type rectifiying defect all specified and directed

M/s PIONEER CONTRACTORS (BID ID -3334309)

BALAJI TRADERS (BID ID -3335852)

ELECTRO ASSOCIATES (BID ID -3335893)

EVEREST CONSTRUCTION (BID ID -3336335)

venus enterprises (BID ID -3335913)