PROVN OF TOILET BLOCK WITH SNACKS CORNER NEAR URC, PROVN OF TOILET FOR SHOPPING COMPLEX AND CONSTR OF SHED FOR PARKING OF AMB OPP MI ROOM AT OTA GAYA

Amount

M&L for Surface dressing n exc 15cm deep in soft/loose soil as in berm.

M&L for Removing excavated soil to a dist exc.250m & n.exc 1.00 Km

Returning, filling in,incl spreading,levelling,watering and well ramming in layers not exc 25CM soft/loose soil

Excavation in trenches n exe 1.5 mtr wide and n exe 1.5 mtr deep for foundation etc all as specified and directed

M&L Cement concretec D2 (1:4:8) 40 mm graded aggregate in foundations,filling and mass concrete all as specified and directed

Form work to sides of rough finished flat concrete surfaces of foundations,footing,bases of columns,raft and raft beams,sides of soffits (if any)of foundation and plinth beam;and similar work;vertical or to batter

Form works torough finished surface sides of squire,rectangular or polygonal pillars,posts,struts,piers,columns and stanchions

M and L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M & L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for reinforced cement concrete (nominal mix) type B-1, 1:2:4 (20mm graded aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M & L for reinforced cement concrete (nominal mix) type B-1, 1:2:4 (20mm graded aggregate) in columns,pillars,piers,post and struts complete all as specified and directed.

S&F mild steel work as in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240 with and including one shop coat of zinc chrominium primer paint complete all as specified and as directed.

M & L for preparation of new or previously untreated surfaces of steel any description over 10cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S and F of framed work such angles or tees with web and flanges cut to shape,drilled and counter-sunk for screw,incl bending and welding angles,as necessery gusset plates not les than 10mm thick,reveting etc not exc 10 kg each brackets confirming toFe-290 gde-E-165

S&F mild steel screw bolts for anchoring 16mm dia (machine made) with hexaginal or squire head at one end and screwd the other ,or screwd both end s,each screwd end to be fitted with washers and one hexagonal or squire nut,not less than 50 cm long

Supply and fixing Pre-painted galvanised aluminumum zinc coating GI based corrugated steel sheet 0.50 mm thick of and colour having tensile strehgth of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L for hardcore of broken stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

M & L for 75 mm thick Plain Cement concrete type C- 2, 1:3:6 (40mm graded stone aggregate) as in sub base.

Sand filling under floors for cushioning of including watering and consolidation

M & L for machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and no pigment complete all as specified and directed.

M & L for Providing, cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) in cills, steps; seismic and other similar bands, plinth courses copings including necessary form work all as specified and as directed

M&L for one coat of glazed lacquer resin and hardener paint (Polyurathene) incl preparation of surfaces of brick,stone,concrete,asbustose ,cement or plaster surfaces of any description over 10CM girth not otherwise described complete all as specified and directed

Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point

M & L RCC (nominal mix) type B1 1:2:4 using 20 mm graded aggregate in beams, cantilevers, lintels over 1.5 m span

Formwork to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. Rough finished surfaces of concrete flat

M & L brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed

M & L for Brickwork with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed

M&L for 15mm thick rendering in cement mortar 1:6 on fair face of brickwork or concrete surface and finished even & smooth (without using extra cement)

M&L for 15mm thick rendering in cement mortar 1:4 on fair face of brickwork or concrete surface and finished even & smooth (without using extra cement)

Supply only Integral water proofing compound

M& L for 2 mm thick of white putty/K white wall care putty in two coats on new/old plastered surfaces and making the surface and making the surface uniform &smooth on walls complete all as specified and directed

M & L for preparing new plastered surface of wall and applying two coats of white wash over one coat of primer complete all as specified and directed

M & L for preparing newly plastered walls surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation

M&L for spreading and levelling n.exc 25cm thick including well ramming incl watering all as specified and directed by Engr-in-Charge

M & L 75mm thick PCC type C-2, (1:3:6) using 40mm graded stone aggregate finished even & smooth without using extra cement as in plinth protection/Path

M & L 75mm thick PCC type D-2, (1:4:8) in sub base floor complete as specified and directed

M & L 25mm thick PCC type B-1, (1:2:4) using 20mm graded stone aggregate as in flooring including finishing cement concrete rough surface without using extra cement

M & L for non skid ceramic coloured tiles of 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exc 0.11 Sqm but n.exc 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 complete.

M & L for Glazed ceramic coloured tiles of size 350x 250x 7mm/ 450X 350X 7mm thick as on vertical surfaces such as skirting, dados and rises to steps etc. over 10mm thick rendering in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

S&F white vitreous china WHB (1st quality ) under counter oval shape size 550x400mm excluiding taps, chain and plug including waste pipe, brackets, 32 mm dia CP coupling cutting for and pinning in ends for brackets or ercting stand complete all as specified and directed by Engr-in-Charge

S& F Vitreous China wash down water closet pan (pedestal pattern), white including fixing bolts, but excuding flushing cistern and flush pipe complete all as specified and directed.

S & F 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 110mm PVC (SWR) P-trap complete.

S & F 15 mm dia bore fancy type chromium plated bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.

S & F of Pillar taps 15 mm, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S & F white soft closing seat cover for pedestal pattern water closet including fixing bolts complete.

S & F brass chromium plated health faucet 15 mm with flexible tube (1.5 m long) of stainless Each steel provided rubber hose and wall hook etc complete all as specified and directed.

S & F vitreous China Urinal, Half stall type, white incl providing and fixing plugs, bedding Each urinal against wall in CM 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing of flush pipe, grating and union for discharge pipe complete.

M&L Cast iron 100mm nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete.

S & F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight Each 60gms)

S & F PVC connections 15mm size with PTMT nuts of length 600mm complete.

S & F 15 mm dia bore fancy type chromium plated two way angle valves/bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed.

Supplying and laying of CPVC pipes 25mm outer dia SDR 11 & Plain CPVC SDR 11 including alll fittings on walls/ceilings or in floors including necessary cutting/chasing of walls and floors complete all as specified and directed.

Supplying and laying of CPVC pipes 20mm outer dia SDR 11 & Plain CPVC SDR 11 including all fittings on walls/ceilings or in floors including necessary cutting/chasing of walls and floors complete all as specified and directed.

S & F of 25mm Male Brass Threaded Adaptor (MTA/ MBTA) or Female Brass Threaded Adaptor (FTA/ FBTA) complete.

S & F of 20mm Male Brass Threaded Adaptor (MTA/ MBTA) or Female Brass Threaded Adaptor (FTA/ FBTA) complete.

M&L for 1000 ltr capacity White rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including all accessories specified and directed.

S&F in 25mm dia bore CPVC gate valves with handle or wheel head, screwed both ends for pipe and fixed

S&F in 20mm dia bore CPVC gate valves with handle or wheel head, screwed both ends for pipe and fixed

S&F 25mm dia ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall of 110 mm bore dia.

S&F PVC (SWR) vent cowl of 110 mm bore dia.

S & F 110mm pvc (SWR) bends any radius provided with access door all as specified and directed by EIC.

S & F of PVC (SWR) junction angle , (Single T) 110mm bore eqal or unequal with access door all as specified and directed by EIC.

Solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colur PVC sheet reinforced with ms squre tube, supplying &fixing in opening as complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tube for top & bottom rail. MS frame shall be covered with heat moulded PVC”C” channel having a PVC steel strip of 20mm width stuck inside with solvent cement for style and plain coloured PVC sheet for top rail lock rail &bottom rail on either side &as gap insert for top rail and bottom rail paneling of plain coloured PVC sheet to be fitted in MS frame welded / sealed to style &rails with suitable PVC sheet beading. And jointed together with solvent cement, supplying and fixing in the frames at site as per specification &drawing

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S & F Aluminium D shape handle cast type anodized 150mm size

S & F Aluminium, anodized, barrel tower bolts of extruded section 200mm long

S&F stainless steel Butt Hinge, medium weight cold rolled of size 100mm

S & F Aluminum alloy, anodized, sliding door bolt with hasp & staple (Bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy size 300mm long.

M&L for granite tiles 20mm thick machine cut , bedded and jointed with gray cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete

Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point

M & L brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4

M & L for Brickwork with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM (1:4)

M & L RCC M-25 design mix using 20 mm graded aggregate in beams, cantilevers, lintels over 1.5 m span

M & L RCC M-25 design mix using 20 mm graded aggregate in Foundations, incl rafts, footings, foundation beams; plinth beams; bases for columns and mass concrete

M & L RCC M-25 design mix using 20 mm graded aggregate in Columns, pillars, piers, posts and struts

M&L RCC M-25 design mix using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

Supply only Liquid water proofing compound

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat

-ditto- all as per Item No 16 Above but 6 to 10 mm dia as in Stirups & Spacers

M&L Rendering 15mm thick on stone masonry surfaces or surface any of brickwork in CM (1:6) finished even & smooth (without using extra cement)

M&L Rendering 10mm thick on brick or stone masonry surfaces or surface any of brickwork in CM (1:3) finished even & smooth (without using extra cement) as in ceiling complete.

M & L for Hard core of Broken bricks gauge n exc. 63mm, deposited, spread & levelled in layers n exc. 15 cm thick, watered & rammed to a true surface

M & L 75mm thick PCC type D-2, (1:4:8) using 40mm graded stone aggregate as in path and concrete surface finished even and smooth without using extra cement.

M & L for non skid ceramic coloured tiles of 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exc 0.11 Sqm but n.exc 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 complete

M & L for 1 mm thick of Birla white putty/JK white wall care putty in two coats on new/old plastered surfaces and making the surface uniform & smooth on walls/ceilings.

Applying three coats of white wash on new Ceiling surface including preparation of surface.

Applying two coats of cement base paint, white or tinted over primer on new wall surface including preparation of surface.

Applying two coats of distemper, white or tinted over 2mm thick birla white/JK white wall care on new wall surface including preparation of surface.

M & L 75mm thick PCC type C-1, (1:3:6) using 40mm graded stone aggregate finished even & smooth without using extra cement as in plinth protection/Path

S & F of 15 mm dia fancy type chromium plated Stop valve, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F Vitreous china squatting pan 'Orissa' pattern size 580 x 440 mm white with integral foot rests including connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc, complete all as specified and as directed.

S&F vitreous china wash basin, white, flat back size 630x450mm excluiding taps, chain and plug including waste pipe, brackets, 32 mm dia CP coupling cutting for and pinning in ends for brackets or ercting stand complete all as specified and directed by Engr-in-Charge

S&F vitreous china urinal, half stall type, white including CP coupling waste pipe white, flat back size 630x450mm excluiding taps, chain and plug including waste pipe, brackets, 32 mm dia CP coupling cutting for and pinning in ends for brackets or ercting stand complete all as specified and directed by Engr-in-Charge

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors of 75 mm bore dia.

S&F PVC (SWR) branch piece, single (singleY) equal or unqual of 110 mm bore dia.

S&F PVC (SWR) vent cowl of 75 mm bore dia.

S & F 75mm pvc (SWR) bends any radius provided with access door all as specified and directed by EIC.

S&F 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement

S & F Powder coated aluminium frame/shutters for windows, ventilators sliding/openable etc icluding joining cleat for fixing, locking arrangement, rubber beading, screws, etc complete all as specified. Note : (i) Glazing and wire mesh shall be measured and paid separetely only as the labour element included in the relavent item. (ii) Item shall be paid as per weight of aluminium section (iii) The rate quoted shall be inclusive of the cost of neoprene beading, glazing pin, screws and powder coated fittings such as locking arraangement etc as required, which shall not be measured for arriving the weight (iv) The rate shall also be inclusive of complete packing with silicon gel around contacting surfaces of aluminium work, and including matching the existing.

S/F PVC connections 15mm size with brass chek nuts of length 450mm complete all as specified and as directed by Engr-in-Charge

S & F Aluminium handle cast type anodized 150mm size

M&L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work incl necessary form work and set in CM 1:4 complete

M & L for providing 50 mm avg thick PCC type B-0, 1 : 2 : 4, (using 12.50 mm graded aggregate) as in coping, and the like including weathering, slightly rounded or chamfered angles and throating complete with using WPC.

M&L for providing water proofing treatment over cleaned roof surfaces with super thermo APP modified water froofing membran comprssing of following for non-approachable roof:- (i) Bitumen based primer conforming to IS 3384-1965 at 0.30 kg per sqm. (ii) One layer of super thermo APP modified water proofing membran with non polyster reinforcement of Make (M/S STP texsa Ltd/hyperplus membrane of M/S IWL India Ltd. M/S STP and Tikki Tar Ltd ) 3mm thick and minimum weight @ 3.50 Kg/sqm laid with gas torch and fasted on roof surfaces with roller. The over laps shall be sealed by flame including vertical surfaces after cutting necessary grooving and making good with PCC gola 1:2:4 type B1 etc adhere to bitumen all as per manufacturer instructions. (iii) Applying two coat of aluminium paint @ 0.20 kg/sqm per coat over bitumen layers as per manufacturer instruction (application including side lap overlaps shall be provided not less than 10cm and jointed sealed with torch as per manufacturer instruction specification.

M&L for point wiring complete with PVC insulated unsheathed FRLS multi stranded copper conductor cable conforming to IS:694 of size 1.5 Sqmm two single core drawn through in and including PVC conduit pipe 20mm dia medium grade ISI marked complete with one run of PVC insulated unsheathed FRLS multistranded copper conductor cable 1.5 sqmm single core green colour earth wire and connecting to earth dolly incl colour coding of cable shall be for phase, neutral and earth wire as specified in MES SSR Part-I 1991 with provn of sunken galvanised not less than 1.12 mm thick MS sheet pressed terminal boxes concealed on wall, with 3 mm thick laminated sheet top cover ISI marked. Make: Hylem/Anchor for fixing of switches/socket/regulator with screws complete including making good of disturbed surface of wall/ceiling/floor complete area in same specification as per existing all as specified and directed.

(a) One light/fan point controlled by one, one way switch 5 Amps

(b) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(c) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board.

Description all as per item No. 1 here in before but 3/5 pin socket outlet point 15 amps independant, with cables of size 2.5 sqmm multistranded, PVC insulated unsheathed FRLS copper conductor cable and 1.5 sqmm PVC insulated unsheathed FRLS copper conductor cable as earth continuity conductor connected to common earth dolly all in separate PVC concuit medium grade not less than 20mm dia ISI marked incl provn of GI sunken box thickness not less than 1.12 mm & 3 mm thick laminated hylem sheet top cover of required size all as specified and directed.

S&F switch piano flush button single pole one way 5 Amp

S&F ceiling rose, surface bakelite 65x50mm 2 to 3 terminal

S&F socket outlet 2-in-1, 3 pin, 5 amp, 230 Volts complete all as specified and directed.

M&L Switch socket combination 2 in 1, 3 pin, 5/15 Amp Flush type universal

S&F sheet metal enclosure distribution board SPN, 8 ways 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable mounting MCBs all as specified directed.

S&F MCB Single pole and neutral, 240 Volts, 40 to 60 amps, all as specified and directed.

S&F MCB Single pole, 240 volts, up to 40 amps, all as specified and directed.

S & F LED street light fitting 35/36 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection with pre wired and necessary mounting arrangements and provision of 2.5 Sqmm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engr-in-Charge.

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

S & F for energy efficient exhaust fan of 230 mm sweep made of metal bod Ventil Air-DS type complete with louver with bolts, nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base complete all as specified and directed. (Note: Cost of suitable opening wall for fixing exhaust fan is deemed to be including in overall rate quoted).

Supply, laying and testing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured heavy duty electric power cable 1100 volts with stranded aluminium conductor of size 16 sqmm 2 core laid in trenches or under road complete all as specified and as directed. (Note: Excavation, sand and brick work will be measure & paid separately).

M & L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground vertically in pit of depth not less than 2.25m deep below normal ground level with top edge of the plate at a depth not less than 1.50 mtr below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected by galvanised wire 4mm dia as earthing lead by means of GI bolts, nuts, chek nuts and washers, earth strip protected by galvanized steel pipe 25 mm bore (light grade) connected to machinery/ equipment all as shown in electrical plate No 03 of SSR part I including necessary excavation and earthwork in any type of soil, 20mm bore light grade GI pipe for watering, funnel, wire mesh, PCC (1:3:6) type C-1 chamber Pit cover 300 x 300 mm with angle iron 20 x 20 mm, 3 mm thick complete all as specified. Note:- (i) The unit rate includes earth lead and protection pipe up to maximum 7.5 mtr from earth plate to earth point/test point. (ii) Earth pit shall be constructed minimum 0.5 mtr away from earth.

M&L for point wiring complete with PVC insulated unsheathed FRLS multistranded copper conductor cable conforming to IS : 694 of size 1.5 Sqmm two single core drawn through in and including PVC conduit pipe 20mm dia medium grade ISI Marked complete with one run of PVC insulated copper conductor cable 1.5 Sq mm single core green colour earth wire and connecting to earth dolly incl colour coding of cable shall be for phase, neutral and earth wire as specified in MES SSR Part I 1991 with provn of sunken galvanised not less than 1.12 mm thick MS sheet pressed terminal boxes concealed on wall, with 3 mm thick laminated sheet top cover ISI marked. Make: Hylum/Anchor for fixing of switches/socket/regulator with screws complete including making good of disturbed surfaces of wall/ceiling/floor in same specification as per existing all as specified and directed.

(a) One light/Extfan point controlled by one No piano type switch 5 AMPS single pole one way

(b) One socket outlet 5/3 pin 5 Amps controlled by one switch on the same board.

S&F for 3 pin socket outlet point 15 Amps independent, with cables of size 2.5 sq mm multistranded, PVC insulated unseathed FRLS copper conductor cable, and 1.5 sq mm PVC insulated unseathed copper conductor cable as earth continuity conductor connected to common earth dolly all are in separate PVC conduit med grade not less than 20mm dia ISI marked ivory colour, incl. provn of sunken galvanised not less than 1.12 mm thick MS sheet pressed terminal boxes of suitable size & 3 mm thick laminated hylem sheet top cover of required size all as specified and directed by Engr-in-charge.

S &F Switch Piano Flush button single pole one way 5 Amp complete all as specified and directed.

M&L for socket outlet 3/5 pin 5Amp flush type complete all as specified and directed.

M&L Switch socket comination multipurpose 2 in 1,5 and 15 Amp Flush type ISI Marked complete all as specified and directed.

S&F of sheet metal enclousure for MCB DB single pole and neutral 8 way with 200 Amps rated bus bar 240 volts double door type complete all as specified and directed.

S&F of MCB SPN capacity 40 to 60 Amps DP 240 complete all as specified and directed.

S&F of MCB SP 30 to 40 Amps 240 volts complete all as specified and directed.

M&L for Earthing complete with galvanized iron earth plate electrode 600 x600x6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.6 meter below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts check nuts galvanized iron or steel all as shown in Electrical plate No. 3 of MES sch pt I testing on completion with & incl. 15 mm bore light grade GI protection pipe 7.5 mtr long for earth lead, PCC (1:3:6) pit with pre cast RCC (1:2:4) cover watering arrangement with funnel, wire mesh 20 mm bore light grade GI pipe, common salt & char coal fixing necessary excavation earth work complete. (GI pipe & GI wire beyond 7.5 mtr will be measured and paid respectively)

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr deep for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 sqm on plan and not exc 1.5m in depth and getting in hard/dense soil complete all as specified and directed by Engr-in-charge

Returning filling in with approved excavated soil including spreading levelling watering and well ramming in layers not exceeding 25cm thick, complete, all as specified and directed.

Removing of surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

Burnt bricks sub class 'B' laid flat dry across the cable for cable protection all as specified and directed.

Sand cushioning to UG cable 8cm thick before laying the cable and 15cm above the cable, stretching and testing of cable complete all as specified and directed. Note:(i) Consolidated / Punned sand shall be considered for purpose of payment (ii) Sand shall be same as specified for plastering work.

S & F exhaust fan, steel body AC single Phase 230V of size 300mm sweep with, blades, and frame and louvers with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection complete all as specified and directed.

M&L ceiling rose , 3 terminal polycarbonate complete all as specified and directed.

M/S NARAYAN & SHARMA (BID ID -3405790)

M/S VIKAS CONSTRUCTION CO. (BID ID -3405199)