REPAIR TO FALSE CEILING, ALUMINIUM PARTITION, DOOR, WINDOW AND OTHER B/R CONNECTED WORKS AT 24ED AF STATION MANAURI

Amount

Dismantling asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings including ridges etc complete as specified & directed by Engineer-in-Charge.

M & L for AC Serrated ridge two pieces adjustable 6mm thick for corrugated or semi corrugated AC sheets fixed with L/J type hook or cranked hook bolt all as specified and directed.

Dismantling poly carbonate sheet (corrugated,semicorrugated, etc.) sheets in roof coverings including ridges etc complete as specified & directed by Engineer-in-Charge.

S&F poly carbonate double layered sheet of any shape and size etc all as specified and directed.

Dismantling plain or corrugated steel sheeting of any gauge, thickness, including Nainital or similar patternroof covering etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick having minimum tensile strength of 550mpa as in ridge, bend to shape for fixing as required, fixed with self-tapping screws. Note:-(i) Colour of prepainted sheet will be as approved by AGE(I). (ii) The bottom colour of sheet must be white.

Dismantling framed truss n exc 10m in span etc. compete all as specefied and directed by E-in-Charge.

M & L for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. compete all as specefied and directed by E-in-Charge. (Fe- 410W Grade-E-250 quality A).

M & L for applying two coats of synthetic enamel paint on new steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

Dismantling wall and ceiling board ( fibre, pulp or insulation etc) or insulation boards/blankets/slabs,any thickness incl cover fillets complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position in unframed work.

S & F for Non asbestos fibre cement building boards fixed / inserted to GI framework with screws of grid 605 x 605mm, for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners withn and including ceiling section(not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. complete all as specified and directed.

Supply, fixing in position premium sand texured finished mineral fibre acoustical ceiling tiles of size 600x600x16mm thick and placed on GI grid powder coated snap grid ceiling, 600x600 module consisting of wall angle section 19x19mm and tee section with web height of 38mm and flange 15mm (colour white) (having rotary stiching on all T-section) with suspension system as per manufaturers instrutions and as approved by the AGE(I). Note :- (i) Ceiling tiles shall be of make Armstrong brand "DUNE RH99 (Bevelled/Tegular)" or equivalent brand of make as specified in particular specifications. (ii) Thickness of GI section shall not be less than 3mm and shall be procured from the tile manufacturer. (iii) Section and hanging system shall have galvanizing of minimum 90 grams per square metre and of same make of tile. (iv) Work shall be executed by the manufacturer's authorised Vendor.

M&L for POP border Designer not exc 20 cm in width.

M&L 2nd class hard wood plain fillets square, rectangular or trangular in section , clean sawn se-cured with nails or beads area exc 6 and n.exc 13 sqcm.complete all as specified and as ditected.

M&L for Second class hard wood (SAL) timber framed and fixed in scantling, wrought.

M&L for preparation of surfaces of any description n exc 10cm width or girth when unconnected with other painting or when painted in different tint on new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for applying two coats of oil bound distemper over a coat of 3mm thick birla putty on ceiling surfaces including rubbing down by sand paper to get even and smooth finish and brooming down for preparation of old surfaces complete all as specified and directed by the Engineer-in-Charge.

M&L for applying two coats of oil bound distemper over a coat of 3mm thick birla putty on walls surfaces including rubbing down by sand paper to get even and smooth finish and brooming down for preparation of old surfaces complete all as specified and directed by the Engineer-in-Charge.

M&L for applying one coats of synthetic enamel paints on old wooden painted surfaces over 10 cm width or girth including preparatinon of surfaces complete all as specified and directed by the Engineer-in-Charge.

S&F glass shelf with moulded edge of size 300X200X12 mm including 'F' clamps complete all as specified and directed by the Engineer-in-Charge.

S&F glass shelf with moulded edge of size 900X100X12 mm including 'F' clamps complete all as specified and directed by the Engineer-in-Charge.

Taking down cement plaster on brick or stone surface of wall built in cement sand mortar including racking out joints, hacking for key, scrubbing down with water etc and M & L for rendering 15 mm thick on fair face of brick walls or concrete surface in CM 1:4 finished even and smooth without using extra cement complete as specified & directed by Engineer-in-Charge.

M & L preparation of old plastered surfaces on walls and applying two coats of weather coat paint (exterior emulsion) complete all as specified and directed by Engineer-in-Charge

M & L preparation of new plastered surfaces on walls and applying two coats of weather coat paint (exterior emulsion) (apex ultima) over a coat of 3 mm thick wall care putty on wall including rubbing down by sand paper to get even and smooth finish and brooming down complete all as specified and directed.

Demolition of un-reinforced Cement Concrete in ground floors and pavings n. exc. 15 cm thickness ( below or above GL) complete all as specified and directed.

M&L for providing 40 mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floor, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

Dismantling floor, hearth or wall tilling including cement mortar bedding(but not backing), and rubbish off premises etc complete all as specified and directed by the Engineer-in-Charge.

M & L non-skid ceramic coloured tiles joint free 7 to 8 mm thick( square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floor set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement and sand mortar (1:4) complete. Note :- Quoted rate shall deem to be included cost of screed bed.

M&L 450mmX300mm X 7-8 mm thick glazed ceramic coloured tiles in vertical surfaces such as skirting, dado, etc set & jointed in neat cement slurry and pointed in white or colured cement to match over & including 10mm thick backing coat in cement and sand mortar (1:3) complete. Note :- Quoted rate shall deem to be included cost of backing coat.

M&L for fabricating aluminium anodised window fixed/sliding type with outer frame of size 62.5x32.5x1.5mm and inner frame for sliding window of size 62.5x23x1.3(top and sides) and bottom channels of size 63x23x1.2mm and for sliding shutter thickness of every sections (top, bottom & middle) should not be less than than1.2mm including cleat, rubber packing glazing clips, snap beading etc as required including 4mm thick glass of approved quility and including aluminium anodised decorative Grill of size D-102 (7.5 mm x 6mm section taking down of old existing window all as specified and directed by Engr-in-charge

S & F in replacement in positions railing using Stainless steel plain pipes of 38mm dia as hand rail, 25mm dia as middle horizontal member (height of Railing approximate 1 metre) vertical member fixed with hammer type fastenes in granite/slab etc complete all as specified and as directed. Note :- (i) Grade of stainless steel pipe shall be S-304. (ii) For payment purpose standard weight of pipe only shall be considered. (iii) For fixing of pipe in concrete/Granite hammer type fasteners of appropriate size shall be provided and as fastener portion shall be covered with stainless steel cap of appropriate size.

S & F Mild steel framed work such as grills, grating etc with ends of bars shoulded, framed guard bars and similar work conforming to Fe-290 Gde E-165 fixed to aluminium windows/ventilators.

Repair to aluminium door/window including necessary welding, reveting, easying, drilling including taking down and repair of hanging devices and locks and making in serviceable condition and re fixing in the same opening and making good from existing surfaces all as specefied and directed. (Note:- Floor spring/hydraulic door closer will be paid seprately) complete all as specified and directed.

Supply only double action floor spring hydranlically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass other part made of mild steel heavy duty and fixed.

Suppluy only door closer, aluminum (Diecast) body, hydraulically regulated, designation 3, universal type suitable for door shutters of 851 to 1000mm in width.

Taking down chowkhat with shutter without taking off shutter from chowkhat area exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed

Taking down Shutters of any description area exc 1 sqm but n. exc. 2.00 sqm each complete all as specified and directed

S & F 35 mm thick 2nd class hard wood glazed and skelton door shutter, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for scuring glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, section 8, clause 8.24 (a), supplied and fitted to chowkats complete all as specified. Note :- (i) Quoted rates deem to be included cost of wooden beading to fix glass panes/ wire cloth. (ii) Glass panes/ wire cloth shall be measured and paid for separately and supply only under respective item of this schedule.

Supply & Fixed 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides etc including teak wood beading on all edges complete all as specified & directed by Engineer-in-Charge. Note :- Thickness of beading for hinge sides shall be 25 mm and on other three edges 6mm thick.

Supply only galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or glavanized wire stables, beads or in steel windows complete all as specified and directed.

M & L for preparation of new wooden surface of any description over 10 cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and directed .

S&F in repair mild steel chromium plated curtain rod 25 mm dia with fixing with brackets etc complete all as specified and directed

M & L PCC 1:2:4 type B1 using 20mm graded stone aggregate for fixing of hold fast etc complete all as specified and directed.

S&F butt hinges medium weight cold rolled mild steel 100mm size, ISI marked complete all as specified and directed.

S&F extruded aluminium alloy handles, anodized 150 mm size ISI marked complete all as specified and directed.

S&F Aluminum Barrel tower bolt 150mm size ISI marked complete all as specified and directed

S&F 300mm length of bolt aluminium alloy, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

Supply & Fixed in repair 300mm mild steel, ordinary rat tail rod double action pattern springs including roller and roller plate complete fixed to steel or wooden door frame including necessary welding cutting opening of wall for fixing brackets complete as specified & directed by Engineer-in-Charge.

Supply only sheet glass, 3 mm thick ordinary quality and glazing with oil putty in squares nexc 0.50 sqm in each pane complete all as specified and directed.

Note :- Credit shown in credit schedule of tender document shall be considered by the tenderer while quoting the rates of various items. The same shall be recovered from various payment to contractor before handing over old material. The contract amount shall be arrived at after deduction of Schedule of Credit from the total quoted amount in BOQ.

RK Enterprises

M/S Garg Sons

HIMANSHU TRADERS

Z N Enterprises