SPL REPAIR TO SINGLE OFFRS ACCN (BLDG NO. T-11, T-14 AND T-23) AT 509 ABW UNDER GE (EAST) AGRA

Amount

Dismantling asbestos cement (corrugated, semicorrugated sheet/ North light curve, Ridge etc.) sheets in roof coverings complete all as specified and directed.

S&F of Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of green colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. Make :- Jindal / TATA / JSW

S&F of Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of green colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. Make :- Jindal / TATA / JSW

S&F Pre-painted, galvanized, pre-fabricated PPGI sheeting 1.00 mm thick in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 including all fixing arrangement etc. complete all as specified and directed. Make :- Jindal / TATA / JSW

M&L for Cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 etc complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section,in frame work, in any position etc complete all as specified and directed.

M&L for 2nd class hardwood in scantling clean sawn and framed for roof truss etc complete all as specified and directed

M&L for Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coat of Creosote oil all as specified and directed.

S&F of Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, wind tie,channel,pipe or flat sections) including distance pieces, welding, cutting , cleats etc Fe 410 -W (GdeE- 250) quality complete all as specified and directed.

M&L for Preparation of new steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed

Dismantling wall and ceiling board or insulation board /slabs/blanket any thickness including cover fillets etc complete all as specified & directed.

S&F Powder coated of Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs etc complete all as specified & directed.

M&L for 4 mm thick non asbestos fibre cement building board designer as in ceiling of size 600 x 600mm fixed to GI snap grid frame work complete all as specified & directed.

M&L for refixing of 4 mm thick non asbestos fibre cement building board designer as in ceiling of size 600 x 600mm fixed to GI snap grid frame work complete all as specified & directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and directed.

All as per item No 15 before but exc 1.5 Sqm and not exc 4.00 Sqm each complete all as specified and directed.

S&F Powder coated / anodized aluminium door & frame not less than weight 0.55 Kg/m incl- 5.00 mm thick tinted glass in half portion and in other half portion 6 mm thick ACP sheet of approved colour complete and fixed with aluminium snap beading, glazing clips, joining clips, screws and 02 Nos of aluminium handle on each door shutter, aluminium anodized tower bolt 200 mm long 02 Nos on each shutter and mortice lock device complete with double keys for each lock, 01 No hydraulic door closure for each shutter complete all as specified and directed with following specifications:- (a) Aluminium door frame = 101.50x44.45mm (b) Aluminium style / top & middle rails of shutter = 83.5 x 44.45mm (c) Aluminium bottom rail of shutter = 114.50x44.45mm (d) Aluminium door frame with shutters shall be fixed in position in brick wall opening as required according to site conditions including all fastening arrangements & making good of existing surface with obd/whitewash over plaster after fixing door etc complete all as specified and directed

S & F powder coated aluminium three track sliding window including frame made of extruded profiles with reqd size of aluminium sections weighing 0.55 kg/m minimum including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings and plain glass on two shutters and aluminium wire cloth on one shutters with two nylon roller on each shutters including star lock handle and aluminium deco grill fixed to outerside of Al frame in suitable type of Al beading etc complete all as specified and directed by Engineer-in-charge

S & F powder coated aluminium window and ventilator shutters including frame, aluminium sections weighing 0.55 kg/m minimum including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws,plain glass on shutters ,anodised aluminium fittings such as peg stays 150 mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) & and aluminium deco grill fixed to outerside of Al frame in suitable type of Al beading complete all as specified and directed by Engr-in-Charge.

S&F of factory made soild PVC door frame of size 50mmx47mm made out of 5mm thick single side prelam PVC sheet reinforced with mild steel square tube , supplying & fixing in opening as per specification and drawing complete all as specified & directed. .

S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face with particle board core, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified & directed.

S&F 100 mm long stainless steel hinges type B-12 and fixed with screw/ welding complete all as specified and directed.

M&L 100 mm long aluminium anodized handle complete all as specified and directed.

Taking down cement or cement lime plaster of any discription on bricks or stone walls/ceiling etc including racking out joints, hacking for kay, scrubbing down with water.

M & L for washed stone grit plaster on exterior walls in two layers , under layer 12 mm thick cement plaster 1:4 ( 1 cemant : 4 coarse sand ) furrowing the under layer with scratching tool , applying cement slurry on the under layer @ 3 Kg of cement per sqm , top layer 15 mm th cement plaster 1 :1 / 2 :2 ( 1 cement : 1/2 coarse sand : 2 stone chipping 10 mm nominal size ) in panels with groove all arround as per approved pattern incl. scrubbing and washing the top layer with brushes and water to expose the stone shipping complete all as specified etc

Forming groove of uniform size 15 mm wide and 15 mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens nailed to the under layer incl. removal of wooden battens , repair to the edges of panels and finishing the groove complete all as specified & directed.

M&L for 10 to 12 mm thick ready mix repair plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacturer instructions) over exterior surface of wall etc complete all as specified & directed. (Note : Coverage for ready mix plaster' shalll be 24 - 28 kg / sqm)

Material & Labour for preparation of new plastered surface and applying one coat of silane siloxane primer @ 0.12 kg / sqm with two coat of premium exterior weather coat paint (silicon additive ) @ 10 sqm / litre in each coat etc complete all as specified and directed. Note : This item shall be operated by authorized applicator aond contractor have to submit the guarantee for 5 year @ 3% of the cost of this item in the favour of GE (E) Agra

M&L for 10 to 12 mm thick ready mix repair plaster with high quality polymer additives and well graded sand and fillers which can be used for plastering (as per manufacturer instructions) over interior surface of wall etc complete all as specified & directed. (Note : Coverage for ready mix plaster' shall be 24 - 28 kg / sqm)

M&L for two coats of oil bound distemper over a coat of average 2 mm thick putty on new plastered surfaces complete all as specified and directed.

M & L for applying bonding agent for bonding old to new concrete surface likes chajja/ beams/ celings/ columns/ facia etc by high performance modified Styrene- Butadiene Rubber ( SBR ) base binder . Applying of binder is as 10 sqm/ per lit etc complete all as specified & directed.

M&L for single component polymer modified repair mortar upto 30 mm thickness in double coat for repair of RCC members likes beams, columns, chajja and facia/Ceiling, mortar having good compressive strength and shrinkage resistance etc complete all as specified & directed.

Material & labour for preparation of new plastered surfaces of ceiling and applying three coats of white wash to match the existing as required, complete all as specified & directed.

Demolition of brick work or stone/boulder masonary built in cement mortar including all quoins, arches, pillars etc complete.

Brick work with sub class 'B' bricks old size straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed.

Dittto all as item no 36 above but except bricks complete all as specified and directed.

M&L for brickwork with subclass ‘B’ bricks old size straight or curved on plan to any radius in half brick thick built in CM 1:4 complete all as specified & directed.

M&L for Preparing old plastered or unplastered surfaces of walls by brooming down or by steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and applying two coats of oil bound distemper over 2 mm thick putty complete all as specified and directed.

Material & Labour for preparation of old plastered surface including removal of existing treatment and applying one coat of silane siloxane primer @ 0.12 kg / sqm with one coat of premium exterior weathe coat paint (silicon additive ) @ 10 sqm / litre etc complete all as specified and directed Note : This item shall be operated by authorized applicator aond contractor have to submit the guarantee for 5 year @ 3% of the cost of this item in the favour of GE (E) Agra

M&L for 2 mm thick wall care putty on wall surface etc all as specified & directed.

Dismantling stone slabs and tiles of any description or thickness in floors / dados, etc laid bedded and pointed in any mortar complete all as specified and directed by the Engineer-in-charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified & directed.

M&L for vitrified tiles of any shade 8 to 10 mm thick (square/ rectangular) polished, area of each tiles n exc 0.36 sqm in floors etc white cement and coloured pigment to match the tiles over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Ditto all as per item no. 44 but in skirting over 10 mm thick rendering in CM 1:4 etc complete all as specified and directed.

Demolition of cement concrete in any description and in any position (unreinforced) complete all as specified and directed.

M&L for plain cement concrete type B-0 1:2:4 (12.50 mm graded aggregate) 25 mm thick as in sub floor, sub base to received tiles complete all as specified and directed.

M&L for non skid ceramic coloured tiles 8 to 10 mm thick (Premium quality) (squre/ rectangular) area of each tiles exc 0.11 sqm but n. exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over 15 mm thick screed bed in CM 1:6 etc complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 450x300x7mm thick fixed on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for applying two coat of fosroc brushbond aqua protect or equivalent to the surface of wall / floor before rendering to prevent the seepage etc complete all as specified & directed.

M&L for 75 mm thick Cement concrete type D-2 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing finishing surface even and rough using broomfinish complete all as specified and directed.

M&L for Providing and laying 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50 mm thick compacted bed of coarse sand,compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified & directed.

M&L for PCC 1:2:4 Type B1 ( using 20 mm graded stone aggregate), in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in eight, copings, kneelers, apex stones bed plates, kerbs chajjas , water troughs, bed blocks and the like including weathering, slightly rounded or chamfered angles and throating, fixing of chain link fencing etc all as directed incl necessary formwork etc complete all as specified and directed.

M & L for 18-20 mm thick black granite of length and width as required including fixing, necessary cutting and support of angle at both corner and middle filled with pcc 1:2:4 or cement mortor 1;3 etc complete all as specified & directed.

M & L for machine cut Kota stone slab flooring 20-25mm thick over 20 mm thick screed bed in CM 1:6. laid and jointed with grey cement slurry mixed with match the shade of the slab including rubbing and polishing complete all as specified and directed.

M & L for kota stone slab 20-25 thick in riser of steps, skirting, dado and pillar laid over 10mm thick backing coat in CM 1:4 and jointed with grey cement slurry mixed with match the shade of the slab including rubbing and polishing complete.

Taking up or down 15 mm bore steel tubing including fittings and connections, including cleaning for Refixing or removal to store complete all as specified and directed by the Engineer-in-charge.

S&F 15 mm bore Galvanized Steel tubes, medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by the Engineer-in-charge.

Taking up or down 20 mm bore steel tubing/ PPR pipe including fitting and connections, including cleaning for Refixing or removal to store complete all as specified and directed by the Engineer-in-charge.

S&F 20 mm bore Galvanized Steel tubes, medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by the Engineer-in-charge.

S&F 1000 litres capacity Rotational moulded polyethylene water storage tanks ISI mark engraved (Cylindrical vertical with closed threaded top) hoisted and fixed in position including 20 mm dia PVC float valve complete all as specified in SSR Part I including dismantling of storage tank.

S&F in repairs 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified & directed.

S&F in repairs Vitreous China wash hand basin counter type white of size 550x440 mm including 32 mm CP waste coupling and rigid pvc waste pipe min 800 mm long fixed over black granite etc complete all as specified and directed by the Engineer-in-charge.

Supply and fix in repairs CP cast copper alloy central hole basin mixture screwed for 15 mm dia GI Pipe including PVC connection etc complete etc complete all as specified and directed

S & F in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed by the Engineer-in-charge.

S&F in repairs 15 mm bore CP stop cock/angle cock, cast copper alloy fancy type, screwed down high pressure, screwed for iron pipe or for unions and fixed complete all as specified and directed by the Engineer-in-charge.

Supply and fixed in repair two way angular valve , 15mm dia, cast copper alloy,CP fancy type with long shank and cup screwd down, high pressure ,screwed both ends for iron pipes or for unions and fixed in pipe all as specified and directed.

Supply & fixing in repair CP tubular towel rail, 60 cm long, 20mm bore, chromium plated complete all as specified & directed.

S & F in repair CI floor trap, plain including jointing with solvent cement (Diameter of outlet 75mm), jointing to waste pipe and fixed in cement concrete 1:2: 4 (type B1) mixed with water proofing liquid @ 200ml in 50 kg cement, inlcuding taking out of old unserviceable connections etc, connecting up new and making good disturbe portion complete all as specified and directed by the Engineer-in-charge.

S&F in repair single piece EWC with UF seat cover, hinges,fixing accessories set ,cistern fittings, rim less tornado flushing size 360x680x750 including P or S trap complete all as specified and directed.

S & F in repairs toilet paper holder with flat recessed type stainless steel, chromium plated or stainless steel with necessary brass nuts & rubber washers, covered with chromium plated spring complete all as spd and directed.

S & F in repairs Flushing Health Faucet for pedestal pattern WC incl flexible pipe and brass chromium plated nuts and bolts and water pipe of size min 1150 mm long & fixed completed all as specified and directed.

S & F Flushing jet for pedestal pattern WC incl. flexible pipe and Brass Chromium Plated nuts and blots and water pipe of size 1150 mm long between dia & fixed complete all as specified and directed.

S&F in repair bib taps long body cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket or PPR pipe etc making good disturbed portion complete all as specified and directed.

Supply & fixing in repairs C.P. grating 100/125 mm dia with or without centre hole etc all as reqd at site complete all as directed.

Supplied and fixed in repair set of 10 mm thick glass corner shelf set of 3 Nos ( size 200 mm,250 mm & 300 mm) complete all as specified and directed

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories.

S & F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall / floor complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified & directed.

S&F 110 mm PVC (SWR) junction single (T single) equal or unequal with acess door. complete all as specified and directed .

S& F 110 mm PVC (SWR) vent cowl complete all as specified and directed. complete all as specified and directed .

S&F PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors, wall including fittings dismantling etc confirming to IS 13592 complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed by the Engineer-in-charge.

S&F 75 mm PVC (SWR) junction single (T single) equal or unequal.with access door.complete all as specified and directed .

S & F in repairs Brass CP wall mixer for mixing hot & cold water srewed down fixed for 15 mm dia GI pipes complete all as specified and directed.

S&F in repair 15mm bore, brass chromium plated single lever sink mixer for making hot & cold water screwed down for pipe and fixed complete all as specified and directed.

S&F in repair kitchen sink with draining board made of stainless steel 1 mm thick with sink coupling & waste pipe including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm, bowl size 410mm x 330mm x160 mm & heavy duty waste pipe 800 mm long complete all as specified and directed by the Engineer-in-charge.

Dismantling of wooden wall panelling incl. frame and make good the surface etc all as specified and directed.

S&F lnsulated 5 mm thick Printed PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site. including necessary beading / framework etc complete all as specified & directed.

M&L for ATT points of contact of wood work by chemical emulsion (Imidacloprid 30.5% SC odorless chemical) in oil or kerosene based solution @ 0.5 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same and making good as existing surfaces complete all as specified and directed.

M&L for treatment of voids in masonry using chemical (Imidacloprid 30.5% SC odorless chemical) emulsion one litre per hole, at 300 mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors and etc complete all as specified and directed. (No extra payment shall be claimed on this account)

Dismantling fencing wire mesh, chain link any type and any size etc complete all as specified and directed.

Supply only GI chain link fencing of size 50 mm * 50 mm & dia of wire not less than 2 mm etc complete all as specified and directed.

Fixing only G I chain link fencing of any mesh, size and to any type fixing with flat iron and nut bolts etc complete all as specified and directed. Note :- flat iron will be measured and paid separately.

S &F of Mild steel round bars Fe 290 (Gde - E-165)10mm dia and over, cut to length, bent to shape required, including cranking, bending hooking ends and binding and fixed with flat iron alongwith fixing with chain linkfencing etc complete all as specified and directed.

S & F screw bolts (machine made) with hexagonal or sqare heads at one end and screwed the other each screw to be fitted with one washers and one hexagonal or square nut length of bolts n exc 50mm and dia of shank 8 to 10 mm dia etc complete all as specified & directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu.m in soft/loose soil, getting out, returning, filling with PCC ( PCC will be paid under separate items ) complete all as specified and directed.

M&L for cement concrete type C-2 1:3:6 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

Dismantling of wooden / PCC fencing post of any description etc complete all as specified & directed.

S & F angle iron as in post and struts in fencing including embeding in concrete, cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., simillar work confirming to Fe-290 Gde E-165 complete all as specified & directed.

Dismantling of structural steel work incl. doors , gates,water tank staging etc complete all as specified & directed.

S&F ornamental Framed and hung as in doors or gates of angle or other section with gusset plates, rails, braces incl. pintle hinges , stops hand made sliding bolts etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing confirming to Fe 290 Gde E-165 complete all as specified and directed. Note:-Weight of gate decided by BOO which will be conveyed by GE before fixing and necessary arrangements for weighing of steel gate by the contractor on his own expense.

S&F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Demolition of Reinforcement Concrete of any description and in any position etc all as specified & directed.

M&L providing precast cement concrete Type B1 1:2:4 (20mm graded aggregate) (nominal mix) for cover slab for manhole, drain and similar articals with plane faces complete all as specified and directed by engineer-in-charge.

S&F TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified & directed.

M&L for 1.00 mm thick mild steel black sheet as in steel gate and similar works cut to size, holes punched including round headed screw welded etc including Two coats of synthetic enamel paint (Ordinary tint) over a coat of red oxide primer including preparation of new or previously untreated surfaces of steel complete as specified and as directed.

M&L RCC M-25 (20 mm graded stone aggregate) as in roof beams, chajja lintle etc complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, in fair finished etc. all as specified and directed

S&F mild steel bars 5 mm dia and over up to 10 mm dia in stirrups space and binders. (TMT) cut to length bent to shape required including cracking,bending spirally for hooping ends and binding with and including mild steel wire not less than 0.90 mm dia quality of steel etc complete all as specified and directed.

S & F in repair Factory Made 18 mm thick 100% Solid WPC ( Wood polymer Composite ) decorative Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850 N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and required frame as per site requirement.Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet /Kitchen/Balcony Doors and Cabinets,complete all as specified and directed.

S&F SS soft close cabinet hinges set of two (any degree as per requirement) for kitchen cabinets/cupboards complete all as specified and directed.

S&F SS cupboard drawer channel set (size 14 to 18 inch) complete all as specified and directed

S&F SS wardrobe hanger rod oval shape including brackets (n.exc. 1.5 m length) including all fittings complete all as specified and directed

S&F SS tie hanger set for wardrobe including All fittings complete all as specified and directed.

S&F Continuous (piano) Stainless steel hinges width of flaps (when open) in 40mm, complete all as specified and directed.

S & F stainless steel 40 mm dia(brass polished) decorative knob for kitchen cup board complete all as specified and directed.

S & F Brass magnet catcher suitable for CB/cabinet shutter complete all as specified and directed.

S & F in repairs Brass chromium plated shower rose 125 mm dia size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair stainless steel plate rack of size 31"x30"x10" mm fixed to wall complete all as specified and as directed.

Taking down carefully existing unserviceable copper / aluminum point wiring of any description & in any position with and ncluding taking out existing unserviceable conduits or battens of any description with sunken boxes/junction boxes and all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, socket, light fittings, lamp holders etc but excluding tube light fittings and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as specified and directed.

M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts grade FRLSH PVC insulated unsheathed cable with proper colour coding drawn in including PVC concealed conduit not less than 20 mm dia with all accessories and FRLSH PVC insulated 1.5 Sqmm multi standard unsheathed copper wire for continues earth, including cutting and chasing of wall surface for laying PVC conduit and modular sunken box of suitable module as per site requirement not less than 1.6mm thick and connecting earth and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles. Note:- Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible at no extra cost for the following :- (a) One light /fan point controlled by one switch

(b) One 5 pin socket outlet 5 Amps on same board

(c) One 5 pin socket outlet 5 Amps on independent board

(d) One bell/buzzer point controlled by one push button on the same board with other switches or independent

(e) One telephone point wiring with cables 0.4 sq mm 2 core

(f) One TV socket point wiring with cables RG-6 Coaxial cable

All as per item No.123 here in before but with cable size 4 Sq mm for one 5 pin 15/16 Amps socket out let on independent board and multistrand insulated copper earth continuity conductor of size 4 sqmm all as specified and directed by Engr-in-Charge.

Supply and fixing modular telephone jack RJ-11 white colour fixed in 1 M box comprising of flush metal box, inner plate and outer cover, all conforming to IS 3854:1997 with finger proof terminals with captive screws having front fixing & removing features without removing plates complete all as specified.

Supply and fixing modular TV coaxial socket outlet fixed in 1 M box comprising of flush metal box, inner plate and outer cover complete all as specified.

Supply and fixing modular switch piano single pole, one way 6 Amps 1 module, complete all as specified and directed.

Supply and fixing modular switch piano flush type 16 Amps single pole one way, one module, complete all as specified and directed.

Supply and fixing modular socket outlet 2/3 pin 6 Amps combined 2 module, complete all as specified and directed.

Supply and fixing modular socket multipurpose 3 pin 6/16 Amps combined 2 module, complete all as specified and directed.

Supply and fixing modular step type, 1/2 module electronic fan regulator heavy duty 120watts 240 volts. , complete all as specified and directed.

Supply and fixing Modular Bell push 6A 1 module pole, one way, complete all as specified and directed.

Supply and fixing call bell, Ding Dong type, 230 volts AC single pole complete all as directed.

Supplying & fixing for ceiling rose PVC Polycarbonate isolated body 62.5 x 25 mm, three terminals, complete all as specified & directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 1 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 2 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 3 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 4 module for mounting switch and sockets all as specified and as directed.

Supply and fixing modular cover plate with metal frame (inner and outer) 8 module for mounting switch and sockets all as specified and as directed.

Supply and fixing blank spacer plate for single module.

S&F in repair Inverter LED batten with square profile and polycarbonate channel. Lithium Ion battery with charging time 8hours-10 hours and back up time upto 4 hours, high optically efficient polycarbonate diffuser, in built electronic driver duly wired upto terminal block, power consumption <20W (Approx 4 feet 20W) luminaire complete all as specified and directed.

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

Supply and fixing in repair LED luminaire 36 watt, 220 V AC, surface/ recessed type with smart colour temp, CCT controllable 595 x 595mm size of LED lighting with remote control with dimming and CCT change options from 2700K to 6500K, housing made from powder coated, CRCA sheet, opaque diffuser for glare free and optimum light suitable for roof ceiling including connecting up with driver and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting complete all as specified and directed.

Supply and fixing in repair LED down light 15 watts, 220 V AC, surface/ recessed type with smart colour temp, CCT controllable with remote control with dimming and CCT change options from 2700K to 6500K, housing made from powder coated, cast alluminium housing, opaque diffuser for glare free and optimum light suitable for roof ceiling including connecting up with driver and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting complete all as specified and directed.

Supply and fixing in repair LED luminaire 595 mm x 595 mm, 36 watt, 220 V AC, 6500 K surface/ recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting complete all as specified and directed.

Supply and fixing in replacement LED building security light fitting 35 Watt 230 V AC out-door type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, fixed to pole or wall of building with and including suitable Bracket made out of 25 mm dia GI light grade pipe, 1.00 m long bent to shape by cutting & welding as required & directed and fixed with two Nos of FI clamps 35x6 mm to be tightened with suitable size of bolts, nut and washers and including painted with two coat of aluminium paint over a coat of red oxide primer, and including connecting the fitting to electric source with & including twin twisted copper flexible wire of size 0.75 sqmm three core with suitable size flexible PVC conduit including all accessories and fixing arrangements for fixing the light fitting and writing the date of fixing on security light with permt marker complete all as specified and directed.

M&L for replacement of sub main wiring using two 2x6 sqmm single core PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) as required dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 1x 6 sqmm as earth continuity conductor connected to earth dolly including taking down old unsv submain wiring complete all as specified and directed. (NOTE : Two run of single core PVC cable with one run of earth conductor and conduit /batten shall be measured as one unit.)

M&L for replacement of sub main wiring using two 2x4 sqmm single core PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) as required dia with standard accessories along-with one run of PVC(green colour) insulated , unsheathed, stranded copper conductor of size 1x 4 sqmm as earth continuity conductor connected to earth dolly including taking down old unsv submain wiring complete all as specified and directed. (NOTE : Two run of single core PVC cable with one run of earth conductor and conduit /batten shall be measured as one unit.)

Supply & fix in repair of sheet metal enclosure Vertical TPN DB 4 Way double door, Suitable for Flush Mounting and Surface Mounting, With 250 A Copper Busbar for each phase with 2 Neutral bar, 2 Earthbar and Cable ties for Cable management, fully insulated busbar & shrouded Neutral bars, Improved Pan assembly for ease of installation, Prefitted masking sheet, Reversible Door for IP 43 DB's, With provision for 160 Amp MCCB as incomer and SP/TP MCB's as outgoing incl cutting/chasing of wall and make in good to the disturbed surface complete all as specified and as directed.

Supply & fix in repair sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 8 way with IP-43 protection double door complete with appropriate size bus bar and neutral link all as specified and directed.

Supply and fixing in repair Single pole and neutral modular type enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp, complete all as specified and directed.

Supply and fixing in repair MCCB 4 pole, 160 Amps, 50 Hz, Icu=36 KA at 415 volts with thermal magnetic alongwith adjustable magnetic protection for current setting Icu=Ics = 100% with adjustable over load setting (minimum 70% to 100%) value from 10 to 15 times of related capacity standard complete all as specified and directed.

Supply and fixing in repair MCB SP 6 to 32 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed.

Supply and fixing in repair MCB SPN 40 to 63 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed.

Supply and fix in replacement of Intelligent BLDC (Brush Less Direct Current) Energy Saving Ceiling fan (copper winding) of size 1400mm sweep with smart remote for easy operation with 5 speed setting and smart features like boost mode and timer functionality for 2, 4,6 and 8 hours, 230 Volts, 50Hz, power consumtion is less than 35 watt, 5 Star rated, noiseless motor operation, inverter stabilization technology, 370 RPM, 245 CFM alongwith necessary accessorie like anti suicide down road 12", canopy, blades, BLDC motor, hanging clip etc and 03 year On Site warranty including writting the MES Number with synthetic enamel paint, including electrically connecting from fan to ceiling rose inlcluding suitable size flexible PVC conduit, complete all as specified and as directed.

Supply and fixing Geyser of 25 Ltrs capacity, 5 star rating AC single phase, 230 volts, Stainless Steel inner tank including connection with three core multistranded copper conductor of size 2.5 sqmm including necessary fixing arrangement i.e anchor nut, bolt, washer,CP pipe connection, grouting and making good to disturbed surface and cleaning of the area, complete all as specified and as directed.

M&L in replacement for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers, of galvanized iron or steel with connected to test point and testing on completion including 15mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire mesh with and including all necessary excavation & earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed. NOTES:-(i) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4 mm dia galvanised iron or steel wire complete all as specified and directed.

Taking down, refixing and connecting electric meters 10-60 amps alongwith CIU & STTD complete as specified and direced.

ASHISH SHARMA (BID ID -3467846)