8933/GWL/E8 PROVN OF ADDITIONAL ROOM ALONGWITH BLDG NO P-199, PROVN OF PAVED PATHWAY WITH INTERLOCKING TILES NEAR BLDG NO P-97, PROVN OF WIDENING OF EXISTING GATE NEAR FRESH GROUP SHED AND ADDITION/ALTERATION TO BLDG NO P-09 IN THE AREA OF AGE B/R-II

Amount

Excavating over areas, n exc 1.5 m deep and getting out in Soft/loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations etc or for shafts, well cess pits, manholes, pier holes, etc but not exceeding 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and exceeding 1.5 m but n. exc 3.00 m in depth for foundations etc or for shafts, well cess pits, manholes, pier holes, etc but not exceeding 10 Sqm on plan and getting out in soft/ loose soil complete all as specified and directed.

M&L for Plain cement concrete (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundations/ mass concrete complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, base for coloumns and mass concrete etc complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 (using 20 mm graded stone aggregate) as in coloumns, pillars, piers, posts and struts etc complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 (using 20 mm graded stone aggregate) as in beams, cantilevers bressummers, lintel over 1.5 m span etc complete all as specified and directed.

M&L for reinforced cement concrete Design mix M-25 (using 20 mm graded stone aggregate) as in slab supported on walls, beams, columns in floor, roof, landing complete all as specified and directed.

Use and waste for formwork to sides of concrete foundation, footing, base of column, raft, raft beam sides and soffits of foundation and plinth beam for rough finished surfaces of concrete complete all as specified and directed.

Use and waste for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works, not exceeding 200 mm thick (horizontal or sloping) including slab edges for rough finished surfaces of concrete complete all as specified and directed.

Use and waste for formwork for two sides of pillar, post, struts, pier column rough finished surfaces of concrete rough finished surfaces of concrete complete all as specified and directed.

Use and waste for formwork to sides & soffits of floor or roof beam rough finished surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars, 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars, 6 mm to 8 mm dia over, cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for mild steel TMT bars 5 mm and over upto and including 10 mm dia, as in stirrups, spacers, and binders, cut to length bent to shape required including cranking bending spirally for hoping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for hard core of broken stone of gauge not exceeding 63 mm, deposited, spread & levelled in layers not exceeding 15 cm thick each layer, watered and rammed to a true surfaces complete all as specified and directed.

M&L for Moorum/red bajri filling in floor or paving laid in layers n.exc 15cm thick each layer, spread levelled and rammed including watering complete all as specified and directed.

M&L for PCC (1:2:4) Type B-0 (using 12.5 mm graded stone aggregate) as levelling course/mass concrete complete all as specified and directed.

M&L for machine cut Kota stone slab 20mm to 25mm thick, as in flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing, over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:3 ) complete all as specified and directed.

M&L for machine cut kota stone slab 20mm-25mm thick as in riser/steps, skirting, dado, cills and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coat in CM (1:3) complete all as specified and directed.

M&L for Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for Brick work with Fly Ash bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for Brick work with fly Ash bricks, straight or curved on plan to any radius, in half brick work built in cement mortar 1:4 complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:4) on brick/concrete/stone surfaces mixed with water proofing compound finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid seperatly under appropiate item of BOQ.

M&L for 15 mm thick rendering in CM (1:6) on fair faces of brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 5 mm thick rendering in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound ISI marked complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of walls & applying 3 coats of white wash on wall surfaces complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of wall & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for preparation of newly plastered sufaces of walls & applying 2 coat of cement base paint over a coat of primer complete all as specified and directed.

S&F MS Pressed steel frames for doors with one or more redates including necessary fixing lugs hinges lock strike plate etc for size of frame 125mmx60mm complete all as specified and directed. Note : Cost of filling of PCC (1:3:6) type C-0 (using 12.5mm graded stone agrregate) in hollow portion of frame deemed included in these items .

S&F for Box type steel windows with side hung shutters (double shutters for glass and guaze) jointed together with an including grills using 10mm square bars @10 cm C/C as per TD No CEBZ/TD/14/2011 including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed and welded incl filling of PCC 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) in hollow section of frame complete all as specified and directed. Note : Glass/guage shall be measured and paid separately under respective item.

S&F for 3mm thick, ordinary glass pin head type and glazing with oil putty, silicone or wooden beads, in square not exceeding 0.5 sqm in each pane complete all as specified and directed.

M&L for 35mm thick factory made 2nd class Hard Wood, plain framed factory made panelled shutters (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board medium density, wood particle board with commercial veneering on both face IS 1003 ( Part-I) kiln seasoned and chemically pressured treated complete all as specified and directed.

M&L for 35 mm thick glazed and skeleton factory made shutters of 2nd class Hard Wood, open rebated and prepare to reveive glass, guage etc (without sash bars) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified complete all as specified and directed.

M&L for preperation of new wooden surface and applying two coats of synthetic enamel paint over a coat of pink primer on new wooden surface any description not otherwise described over 10 cm width or girth and complete all as specified and directed.

S&F for MS Sliding door bolts Rod pattern stove enamelled black with bolts not less than 12mm dia with and including a minimum of 6 bolt and nuts four on bolt plate and two on staple plate of 250mm size complete all as specified and directed.

S&F for Aluminium butt hinges of 100mm size type C-22 complete all as specified and directed.

S&F for MS 150 mm ordinary rat tail springs plate type including rollar plate etc complete all as specified and directed.

S&F for galvanised wire cloth, 0.48 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed

S&F for aluminum handles cast type, anodized of 150 mm size complete all as specified and directed.

S&F for aluminium anodised barrel tower bolt of 150mm size of extruded section complete all as specified and directed.

S&F for factory made steel vetilator with top hung glazed shutters, including projecting type hinges, with steel handles and steel peg stays, complete with glazing bars, complete all as specified and directed.

S&F for factory made steel ventilator with top hung glazed ventilator including projecting type hinges with steel handle and steel peg stay complete witout glazing bar, dovetailed or welded complete all as specified and directed.

S&F for framed work such as grills gratings, etc, with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe 290 E-165 complete all as specified and directed.

M&L for painting to steel surface exc 10 cm width or girth with two coats of synthetic enamelled paint over a coat of red oxide including prepration of newly or previously untreated surface complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C2, (using 40mm graded stone aggregate) as in plinth protection, finishing the surface even and smooth w/o using extra cement including forming & filling expension joints 65 mm deep x 10 mm wide filled with sealing compound grade A complete all as specified and directed.

M&L for 10 mm thick rendering in CM (1:4) over roof, surface finished even and Smooth mixed with water proofing compond complete all as speceified and directed. Note : Water proofing compound shall be measured and paid separately under appropriate item of BOQ as "supply only "

M&L for applying water proofing treatment with the following coats :- (a) First coat of bitumen primer conforming to IS-3384 @ 0.3 Kg/sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3kg /sqm and minimum 3 mm thick reinforced with polyster non woven fabric land on primed surface by torch application (c) third two coats of aluminium bituminous paint (200ml/sqm i.e 100 ml/sqm in each coat) over polymetric membrane complete all as specified and directed.

Supply only Liquid water proofing compound complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in Hard / dense soil soil complete all as specified and directed.

Removing surplus soil obtained from excavation to a distance exceeding 500 metre but n. exc 1.50 Km and depositing where directed at a level not exceeding 1.5 metre above the starting paint complete all as specified and directed.

Surface excavation n.exc. 30 cm deep and avg 15 cm deep and getting out in any type of soil complete all as specified and directed.

Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with aproved colour, design & pattern as in foothpath, parks, lawns, drive ways or light traffic arking etc. of required strenght, thickness & size /shape, made by table vibrating method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra cement complete all as specified and directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints excet at sharp curve shall not more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Excavation in trenches not exc 1.5 mtr depth for foundation etc n.exe 10sqm on plan in and getting out in hard dense soil complete all as secified and directed

Removing excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as secified and directed.

M&L for providing PCC 1:3:6 type C2 (using 40mm graded stone aggregate) in foundation filling and mass concrete complete all as specified and directed.

S&F for Framed work ornamental and intricate design such as grills, gratings, etc with ends of barss shouldered and/or riveted or forged into spikes framed guard bars barred iron doors ladders, framed balusters walkways railings, framework of water tanks and similar work conforming to Fe.290 Gde-E-165 complete all as specified and directed.

M&L for Granite slab 18 mm to 20 mm thick machine cut, bedded and joined with cement and pointed with white cement with admixture of pigment to match over and including 20 mm thick screed bed in CM (1:3) the shade of granite stone including cutting and polishing type as in cill and jamb/skirting, steps cooking plateforms includigng rounding off the exposed edges and polishing complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint including preparation of new steel surface over 10 cm width or girth comlete all as specified and directed.

M&L for surface dressing n exc 15 cm deep in soft/loose soil complete all as specified and directed.

M&L for Plain cement concrete (1:4:8) type D2 (using 40 mm graded stone aggregate) as in foundations/ mass concrete complete all as specified and directed.

M&L for rubble random rubble uncoursed, well bounded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces, rendering in cement mortar (1:6) mixed with water proofing compound as per manufacturer's instruction & finished even and smooth without using extra cement complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid seperately under appropriate item of Sch 'A' as "supply only")

M&L for 10 mm thick rendering in CM (1:6) on fair faces of brick work or conrete surfaces/stone masonary and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of wall & applying 2 coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of newly plastered sufaces of walls & applying 2 coats of oil bond distemper over a coat of primer complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 Type B1 (using 20 mm graded stone aggregate) as in beams, cantilevers bressummers, lintel over 1.5 m span etc complete all as specified and directed.

M&L for hard core of broken bricks of gauge not exceeding 63 mm, deposited, spread & levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

M&L for cement concrete 1:2:4 type D-2, (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for Non-skid Ceramic, joint free, coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and directed.

M&L for ceramic tiles, joint free, coloured tiles 7mm to 8mm thick as in skirting fixed over and including 10 mm thick cement plaster in CM (1:3) set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

S&F for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc (cut to ordinary lengths i.e. within 20mm of the length indicated) confirming to Fe 410-W (Gde-E- 250) quality-A complete all as specified and directed.

S&F for pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F in renewal of E- grid False ceiling 4 mm thick HPSC pre-prime non asbestos fibre cement building board (E-classic of size 600mm x 600 mm/ 595 mm x595 mm) decorative finish fixed with clips and screw including powder coated galvanised MS grid frame work false ceiling of (Main Tee of size 32mmx24mmx0.55mm cross tee of size 24mmx24mmx0.35mm) and with slot for fixing including suspended with 1.2 mm dia GI wire hangers fixed with steel dash through fasteners from purline of the roof complete all as specified and directed.

M&L for concealed point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed 20mm dia non metallic rigid PVC conduit medium grade confirming to IS 14930 (Part-I) 2001( ISI marked with valid CML No) not less than 20 mm dia with all fitting and fixing accessories and 1.5 Sqmm FRLSH, PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes factory made for mounting switch, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches sockets etc complete all as specified and directed for the following;

One light point controlled by one switch.

One Ceiling fan point controlled by one switch.

One 5 pin multipurpose socket out let 5/6 Amps on the same board with other switch.

One 3 pin/5 pin switch socket outlet, 5 Amps on independent board.

Description all as per item No 78 here in before but point wiring with 2.5 sqmm FRLSH H confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire complete all as specified and directed.

S&F for switch piano, flush button single pole one way 5 Amp complete all as specified and directed.

S&F for socket out let, multipurpose, 2 in 1 5 pin, 5 Amp complete all as specified and directed.

S&F for switch piano, flush button single pole one way 15 Amp complete all as specified and directed.

S&F for socket out let multipurpose flush type, 2 in 1, 6 Pin 5/15 amps complete all as specified and directed.

S&F for ceiling rose surface bakelite of 63.5 mm dia three terminal complete all as specified and directed.

S&F for electronic step rotary type fan regulator of two module capacity 80 to 100 Watt, 240 volts, AC 50Hz complete all as specified and directed.

S&F for LED Lamp 09/10 watt 130 lm/watt with 5 star rating complete all as specified and directed.

M&L for sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade confirming to IS 14930 (Part-I) 2001,(ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 6 Sqmm FRLSH copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. (NOTE: (i) Two runs of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

S&F for Decorative ultra slim LED Tubelight fitting of LED with extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt, 130 lumen/watt 6500K fitting, incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor wire for electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed.

S&F for MCB DB, sheet metal enclosures double door SPN 8 way wiith suitable size rated bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F for MCB SPN 63 Amps, 240 volts 'C' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed.

S&F for MCB SP 240 volts, 6 to 32 Amps, 'C' series 10 KA including connection with suitable size copper lugs complete all as specified and directed.

M/s Subhash Construction Co.

Jai Mahakaal Construction

ASW ENTERPRISES