PROVN OF TWO GUARD ROOMS AND CERTAIN SANCTIONED WORKS AT LEKHAPANI MILITARY STATION UNDER GE LEKHAPANI

Amount

Surface dressing not exceeding 15 cm deep in soft/loose soil complete all as specified and directed.

Excavation over area in soft/loose soil, n. exc. 1.5m deep and getting out complete all as specified & directed.

Excavation over area in soft/loose soil, exc. 1.5m deep and not excluding 3.0m deep and getting out complete all as specified & directed.

Surface excavation not exceeding 30 cm deep and averaging 7.5 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth;for foundation,etc. or for shafts,wells,cesspits, manholes, pier holes,etc.not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

M & L for PCC in foundation, filling and mass concrete in M7.5 (Nominal Mix) using 40mm nominal size graded crushed stone aggregate complete all as specified and as directed.

M & L for PCC in foundation, filling and mass concrete in M15 (Nominal Mix) using 40mm nominal size graded crushed stone aggregate complete all as specified and as directed.

M & L for brick work with subclass “B” Old size bricks, straight or curved on plan,exceeding 6 m mean radius, built in CM 1:6 complete all as specified and directed

M & L for brick work with subclass “B” Old size bricks, straight or curved on plan,to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed

M&L for providing reinforced cement concrete M-25 (Design Mix) using 20mm nominal size graded crushed stone aggregate as in foundations,including rafts,footings,foundation beams,plinth beams;bases for columns,etc;basement slabs,under-reamed piles and mass concrete comlpete all as specified and directed.

M & L for RCC M-20 (Nominal Mix) (using 20mm graded stone aggregate) as in beams, cantilever, bresummers, lintels over 1.5m span complete all as specified and directed. (Note: Reinforcement shall be measured and paid separately)

M&L for providing reinforced cement concrete M-25 (Design Mix) using 20mm nominal size graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors,roofs,landings,balconies,canopies,deck slabs and in shelves and the like comlpete all as specified and directed.

M&L for providing reinforced cement concrete M-25 (Design Mix) using 20mm nominal size graded crushed stone aggregate as in beams,cantilevers,bressumers,lintels over 1.5m span etc.complete all as specified and directed.

M&L for providing reinforced cement concrete M-25 (Design Mix) using 20mm nominal size graded crushed stone aggregate as in chajjas comlpete all as specified and directed.

M&L for providing reinforced cement concrete M-25 (Design Mix) using 20mm nominal size graded crushed stone aggregate as in fins,fascias,louvers,parapets,and railings, newels,balustrade, and the like etc. complete all as specified and directed.

M&L for providing reinforced cement concrete M-25 (Design Mix) using 20mm nominal size graded crushed stone aggregate as in columns,pillars,piers,posts and struts etc. complete all as specified and directed.

M&L for precast cement concrete louvers and jallies, 40mm thick (measured solid) in cement concrete M-15 (Nominal mix) using 12.5mm nominal size coarse aggregate including all moulding but excluding frame and fixed in position using cement mortar 1:4 complete all as specified and as directed.

M&L for providing precast cement concrete M15 (Nominal mix) using 20mm nominal size graded crushed stone aggregate in window or door cills, lintles, bressumers, steps, quoin blocks (for use with masonry), string course, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, pintle blocks, ancho-rage block, bonders (for stone walling), corbels, brackets etc (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc and setting in cement mortar 1:4 complete with joints to match complete all as specified and as directed.

Spreading & leveling well ramming, watering etc. as required in layers not.exc 25cm thick complete.

M&L for returning filling in, including, spreading & leveling, watering and well ramming in layers the soil not exc 25cm commplete all as specified and directed.

M&L for hard core of broken stone or boulders of gauge n.exc 63mm, deposited, spread, & leveled in layers n.exc 15cm thick watered & rammed to a true surface.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M & L loose filling with broken brick aggregate of gauge 80 to 150 mm in soakage pit, saok well etc complete all as specified and directed.

M & L loose filling with broken brick aggregate of gauge 40 to 80 mm in soakage pit, saok well etc complete all as specified and directed.

M&L for cement concrete M-10 (Nominal mix) using 40mm nominal size graded crushed stone aggregate 75mm thick in sub base for laying tiles, pavings etc all as specified and as directed

M&L for 75mm thick, plain cement concrete M-10 (Nominal size graded stone aggregate finished surface even and fair as in plinth protection all as specified and as directed.

M&L for filling in poition 80/75 industrial grade bitumen mix filler of proportion 80 kg of hot bitumen, 1 kg of cement and 0.25 cum of coarse sand for expansion joints complete all as specified and as directed.

M&L for plastering 10mm thick on fair faces of brick work or concrete surfaces (on vertical surface) in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for plastering 15mm thick (in two coats of 10mm and 5mm thick) on fair faces of brick work or concrete surface ( on vertical surfaces) in cement mortar 1:4 with integral water proofing compound finished even and fair complete all as specified and as directed. Note Water proofing compound will be measured and paid for separate.

M&L for plastering 5mm thick on fair faces of brick work or concrete surface on ceiling in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 40mm thick damp proof course in cement concrete M15 (Nominal mix) using 12.5mm nominal size graded crushed stone aggregate mixed with integral water proofing compound to horizontal or vertical surfaces including necessary form works complete all as specified and as directed. (Note :- Water proofing compound will be measured and paid for separately).

M&L for formwork to soffits of suspended slabs such as roof slabs, landings and similar work not exc 200mm thick (Horixontal or sloping) for rough finished flat surfaces of concrete complete all as specified and as directed.

Use & waste of formwork with rough finished flat concrete surfaces, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work exc 200mm wide complete all as specified & direct

M&L for formwork to sides of concrete foundation, footings, base of coloumns, raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished flat surfaces of concrete complete all as specified and as directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels. Cantilevers, shelves including supports, overhangs, etc also splays between floor and beam etc for rough finished flat surfaces of cocrete complete all as specified and as directed.

M&L for formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished flat surfaces of concrete complete.

Use & waste of formwork with fair finished flat concrete faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified & directed.

M&L for formwork to sides of pillars, posts, struts, piers, coloumns and stanchions for rough finished flat surfaces of concrete complete.

M & L for RCC M-20(nominal mix) (using 20mm graded stone aggregate) as in slab / shelves supported on wall, beams and columns in floors, roofs, landings, deck slabs and in shelves and the like complete all as specified and directed. (Note: Reinforcement shall be measured and paid separately)

M & L for Reinforced cement concrete M-20 (Nominal mix), 1:1 1/2:3, type B-1 (using 20 mm graded crushed stone aggregates) as in walls, retaining walls, ballast walls & the like, any thickness, above top of footings, including attached pillasters & buttresses etc complete all as specified & directed.

S&F pressed steel door frames conforming to IS 4351, manufactured from commercial mild steel sheet of 1.25 mm thickness size 105mm x 60mm profile B, single rebate including hinges, mortar guards, lock strike plate, shock absorbers complete all as specified and as directed.

S&F solid PVC door frames of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube all as per specification & drawaing complete all as specified and directed by Engr-in-Charge.

S&F 30mm thick factory made solid panel PVC door shutter as per IS 15931 : 2012 with 19 gauge thickness mild steel tube and tapering 20mm in 45 degree angle on both sides forming styles and on the inner side to form top and bottom rail and on both sides to form lock rail complete all as specified and as directed.

S&F flush door shutter 30mm thick solid core of block boards construction, MR grade, commercial type with stiles rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1) : 1999 both sides face panel of plywood as per IS 710 : 2010 internally lipped complete all as specified and as directed

S&F hot rolled medium and high tensile structural steel of grade E-165 as per IS 15911:2010 as in bands, straps, suppkrots or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay) heavy for large gates hooks and pintle hinges large hasps and staples, chains hand made sliding bolts, clamps hold fasts, wall ties, hooks for hanging fansn plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

S&F aluminium alloy sliding door bolts with hasp, staple and fixing clips of sheets, or extruded sections and fixing bolts and sliding bolts of extruded sections of aluminium alloy, 300mm long anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.

S & F, 150 mm size, aluminium anodised , barrel tower bolts of extruded section & fixed complete all as specified and as directed.

S & F, 200 mm size, aluminium anodised , barrel tower bolts of extruded section & fixed complete all as specified and as directed.

S&F aluminium alloy handle, fabricated type, 150mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 :1996 complete all as specified and as directed.

S&F aluminium alloy handle, fabricated type, 125mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 :1996 complete all as specified and as directed.

S&F 100mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341:1992 complete all as specified and as directed.

S&F, mild steel 300mm size, ordinary rat tail rod pattern springs, including roller and roller plate complete fixed to wooden shutter all as specified and as directed.

S&F steel windows four shutter (two for receive glass, and two shutter for gauze) with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F, steel ventilators with top hung shutters including hinges, steel peg stay complete all as specified and as directed.

S&F sheet glass ordinary quality 4mm thick glazed with oil putty or fixed with beads in square not exc 0.5Sqm in each pane complete all as specified and directed.

S&F, galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified & as directed.

M & L for preparing new wood and wood based surfaces of any description over 10 cm width or girth,not otherwise described applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge

M & L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over one coat of alkali resistant primer complete all as specified and as directed

M & L for preparation of old plastered surfaces of wall and applying two coats of cement base paint complete all as specified and as directed.

S & F vitreous china wash down water closet (pedestal pattern), white including thermoplastic seats and covers of grade 2 type, flat with hinging device of bronze or brass with nickel chromium plating, fixing bolt, connector to flush pipe and making connections to flush pipe, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge.

S & F 10 litres capacity, low level, syphonic type, white, plastic flushing cistern as per IS 7231: 1994 with inlet, ball valve, float and handle including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed.

S & F wash basins, vitreous china, white, flat back, size 630 mm X 450 mm with and including cast iron brackets (embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws), 32 mm nominal size, copper alloy, nickel chromium plated finish waste fittings, including painting of fittings and brackets, sealing gap between wall and basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings etc. with silicone sealant complete all as specified and as directed.

S & F flexible (coil shaped) PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm connected to PVC waste fittings complete all as specified and as directed.

S & F 32 mm nominal size, waste coupling of PTMT (half or full threaded), minimum weight 45 grams with including silicone sealant complete all as specified and as directed.

S & F sheet glass shelf assembly consisting of 5.50 mm thick glass sheet shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed.

S & F towel rail 600 mm long of PTMT fixed with and including chromium plated brass screw and wooden/plastics cleats, minimum weight 190 gms complete all as specified and as directed.

M & L for PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

S & F 15 mm nominal size, nonrising spindle type fancy bib taps as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

S & F 15 mm nominal size, nonrising spindle type fancy stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

S & F 20 mm gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed to pipe complete

S & F 15 mm nominal size, nonrising spindle type fancy pillar taps as per IS 8931: 1993, cast copper alloy body with knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

S & F brass chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed.

S & F 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed.

S & F rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 500 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes all as specified and as directed.

S & F 20 mm nominal size brass float valve, high pressure, with polythene float and flynut, screwed for iron pipe and fixed complete all as specified and as directed.

Supply and lay high density polyethylene pipe (HDPE) of pressure rating PN 6(0.6 Mpa), material grade PE 63 and nominal dia 20 mm including all fittings and fixtures in trenches complete all as specified and as directed.

Supply and fix PVC SWR Nahani/ Floor trap plain with grating including jointing with solvent cement, dia of outlet 75 mm, water seal minimum 75 mm, complete all as specified and directed by Engineer in charge.

S&F, PVC (SWR) pipes 100 mm bore, single socketed, in any length with rubber ring joints, fixed in trenches complete all as specified & directed.

S&F, PVC (SWR) pipes 150 mm bore, single socketed, in any length with rubber ring joints, fixed in trenches complete all as specified & directed.

S & F PVC-U, type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 75 mm dia, fixed to walls complete all as specified and directed by Engineer- in- charge .

S & F PVC-U, type A as per IS 13592: 2013 single socketed rain water pipes in any length with rubber ring joints,100 mm dia, fixed to walls complete all as specified and directed by Engineer- in- charge .

S & F UPVC bends with inspection door (any angle), 100 mm dia conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge

S & F UPVC vent cowl, 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge

S & F UPVC bends with inspection door (any angle), 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed.

M & L for mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed.

S & F mild steel TMT bar 5mm dia and over upto and including for stirrups spacers binder etc, bending, spirally for hooping for slab bend etc , hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

M & L for glazed, colour ceramic wall tiles (group B III), area of each tile exceeding 0.12 sqm but not exceeding 0.22 sqm, length more than 340 mm but less than 460 mm, minimum 8 mm thick on vertical surfaces including 10 mm thick backing coat in cement mortar (1:4), set and jointed in neat cement slurry and pointed in epoxy mortar to match all as specified and directed

M & L for ceramic tiles, coloured ceramic floor tiles (group B Ia), 600 mm X 600 mm X 10 mm in floors including 15 mm thick screed bed or bedding layer in cement mortar(1:6) set and jointed in neat cement slurry and pointed in epoxy mortar to match complete all as specified and directed.

Taking down cement plaster of any description on brick walls etc including racking out joints, hacking for key, scrubbing down with water complete as directed.

M&L for glazed coloured ceramic tiles in vertical surface 450 x 350 x 7 /300x250x7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering in cement mortar (1:4) complete all as specified & directed.

M&L for non-skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified & as directed.

Preparation of newly plastered surfaces on ceilings and applying three coats of white wash complete all as specified and as directed.

Supply only approved intrgral water proofing compound complete all as specified and directed.

Preparation of newly plastered surfaces on walls and applying three coats of white wash complete all as specified and as directed.

M&L water proofing treatment on floor/roof etc comrising with the following operation as specified herein below :- (a) M&L 15mm thick plastering in cement mortar 1:4 finished even and smooth. (b) Preparing & cleaning of fully dried cement concrete. (c) Applying one coat of cold bituminious primer to the plastered surfaces @ 0.25liters per sqm conforming to IS-3384-1986. (d) A layer of APP based polymeric membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyester non woven fabric (weighing not less than 160gms/sqm) shall be applied over bituminious primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100mm on transverse direction and 75mm in longitudinal direction. (e) One coat of aluminium paint over the APP based membrane @ 0.11 kg/sqm. Make : MOPLY-FP manufactured by M/s Texa India Ltd or IWL (HYPERPLAS POLYMER) manufactured by M/s IWL approved by GE/AGE(I)).

Material & labour for rendering 15 mm thick in cement mortar 1:4 over RCC Roof mixed with water proofing compound @ 3% by weight of cement or manufacturer instruction all as specified. (Note;- water proofing compound will be measured and paid separately as supply only)

Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

Treating the soil under plinth protection and extra at the rate of 5 litres of emulsion per square metre of surface area

M&L for 100mm thick PCC as in floor 1:3:6 type C-2 using 40mm graded aggregate.

M & L for chequered cement concrete tiles, cast in rubber mould, glossy finish of approved colour, general purpose, double layer, size 25 cm X 25 cm X 22 mm thick, with mixture of white and grey cement in equal proportions and pigments, set, jointed and pointed in neat cement slurry in floor including laying over 20 mm thick bedding of cement mortar(1:4) all as specified and as directed.

M & L for construction of septic tank for 10 users as per drawing No. TD/SZ/504 sheet No. 1/1 including excavation in soft/ loose soil, removal of spoil to 50 metres, lean concrete in M7.5(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate, RCC in M25(Design Mix) using 20 mm nominal size graded crushed stone aggregate, brick work in cement mortar (1:4), internal plastering in 20 mm thick in cement mortar (1:3) in two coats of (12 mm + 8 mm) mixed with integral water proofing compound, external plastering in 15 mm thick in cement mortar (1:4) in two coats of (10 mm + 5 mm) mixed with integral water proofing compound upto 15 cm below ground level, flooring/ bedding in M15(Nominal Mix) using 20 mm nominal size graded crushed stone aggregate, precast concrete in M25(Design Mix) using 20 mm nominal size graded crushed stone aggregate, PVC vent pipe and cowl as PVC-U, type B as per IS 13592: 2013 and UPVC as per IS 14735: 1999, TMT bars as specified, cast iron soil waste pipe as per IS 1789: 2002 or IS (3989: 1984, cast iron, pattern 1 footstep as per of IS 5455: 1969 spaced 400 mm horizontally and 400 mm vertically complete all as specified and as directed.

M & L for construction of soak well for 10 users as per drawing No. TD/SZ/504 sheet No. 1/1 including excavation in soft/ loose soil, removal of spoil to 50 metres, lean concrete in M7.5(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate, RCC in M25(Design Mix) using 20 mm nominal size graded crushed stone aggregate, brick work in cement mortar (1:4), external plastering in 15 mm thick in cement mortar (1:4) in two coats of (10 mm + 5 mm) mixed with integral water proofing compound upto 15 cm below ground level, brick bat filling with 150 mm to 80 mm graded brick bats for filling the bottom layer and 80 mm to 40 mm graded brick bats for the top layer, precast concrete in M25(Design Mix) using 20 mm nominal size graded crushed stone aggregate, PVC vent pipe and cowl as PVC-U, type B as per IS 13592: 2013 and UPVC as per IS 14735: 1999, TMT bars as specified, cast iron soil waste pipe as per IS 1789: 2002 or IS (3989: 1984, complete all as specified and as directed.

M & L for precast cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) complete with joints to match complete all as specified and as directed

M & L for 150 mm internal dia salt glazed stoneware pipes, class SP1 as per IS 651: 2007 laid in trenches and jointed with cement slurry and yarn complete all as specified and as directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. complete all as specified and as directed.

M & L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:4 complete all as specified and as directed.

M & L Brick work with sub-class `B' bricks,in one brick thick honey comb walling built in Cement Mortar 1:3 Complete all as specified and directed.

M & L for cement concrete in surface channels and drains in M15(Nominal Mix) using 20 mm nominal size graded crushed stone aggregate complete all as specified and as directed.

Material and labour for plastering 15 mm thick (in two coats of 10 mm and 5 mm thick) on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:4 finished even and fair complete all as specified and as directed.

M&L for forming contraction (Dummy) joint 65 mm deep 10 mm wide, filled with sealing compound grade 'A' complete.

Forming construction joint 30mm deep X 10mm wide filled with sealing compound Grade 'A', complete all as specified and directed.

M&L for 100 mm thick PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in sub base including form work.

M&L for 150 mm thick PCC 1:2:4, Type B2, using 40 mm graded crushed stone aggregate as in paving/path finished fair and even including 150mm wide form work and compacted to concrete by using niddle/plate vibrator and brooming at top surface of concrete complete all as specified and directed.

Demolition and breaking up 100 mm bore, drain pipes Salt glazed ware, AC or reinforced concrete set in Cement Mortar complete all as specified & directed.

Demolition & breaking up 150 mm bore, drain pipes salt glazed ware, AC or reinforced concrete set Cement Mortar complete all as specified & directed.

M&L for cement conrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregates) as in bed to drain pipes of 110mm bore, including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L for cement conrete 1:3:6, type C-2 (using 40mm graded crushed stone aggregates) as in bed to drain pipes of 150mm bore, including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M & L providing pre-cast cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab of manholes, septic tank, soak well etc set in cement mortar 1:4 with plain fair faces including chamfered weathering, throating etc including necessary use and waste of form work complete all as specified and as directed.

Demolition of unreinforced cement concrete in ground floors and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for glazed coloured ceramic tiles in vertical surface 450 x 350 x 7 /300x250x7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering in cement mortar (1:4) complete all as specified & directed.

S&F glazed ceramic light coloured tiles 300x300mmx7mm thick, in floor, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 15mm thick screed bed in CM 1:4 on concrete surface including roughening the surfaces and brushing with neat cement slurry of existing concrete floor, scrubbing down with water and disposing off the wastage to low laying areas to a distance exceeding 50 Mtr but not exceeding 100 Mtr away complete all as specified and directed.

Dismantling plain or corrugated steel sheeting ,any gauge, thickness, including Nainital or Similar pattern roof coverings complete and keeping serviceable sheets in safe custody for reuse in the work complete all as specified & directed.

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

S&F 4 mm thick, Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework as in ceiling complete as specified and directed.

M & L preparing newly surfaces of ceiling and applying three coats of white wash complete as specified and directed.

Dismantling timber scantlings 40 Sq.cm and over in section as in unframed work, in any position complete all as specified & directed.

Dismantling timber fillets, rails, posts, rafters, purlins, etc in unframed work under 40 Sqcm in section in any posotion complete all as specified & directed.

M&L for second class hardwood, scantlings, clean sawn, timber fixed in framed work as in trusses etc. complete as specified and directed.

S & F second class hard wood, plain solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints and as specified and directed.

S&F, Second class hard wood, Plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads, cross sectional area exc 3 and n.exc 6 Sqcm complete as required and as specified and directed

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work & precast concrete articles complete all as specified & directed.

S&F, Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheets, 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof overing/cladding to wall, fixed with self tapping screws as specified and directed.

S&F, Pre-painted galvalume aluminum zinc coating GI based Plain steel sheets, 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge, etc. fixed with self tapping screws complete all as specified & directed.

Dismantling wall and celling board (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified & directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M & L for preparation of new plastered surfaces of wall and applying two coats of distemper oil emulsion complete all as specified & directed.

M&L for completely removal of the existing treatment from wall and applying two coats of cement paint over a coat of 1mm thick wall putty over a coat of cement primer on wall including prepration of surfaces.

M&L for completely removal of the existing treatment from wall and applying two coats of oil bound distemper over acoat of 1mm thick wall putty over a coat of cement primer on old surfaces of wall including prepration of surfaces.

M&L two coats of synthetic enamel painting on steel surfaces of any description over 10 cm in width or girth not otherwise described including prepration of surfaces

M&L two coats of synthetic enamel painting on wooden surfaces of any description over 10 cm in width or girth not otherwise described including prepration of surfaces.

All as per ser item No 146 above but one coat of synthetic enamel paint on old painted surfaces

M & L for writing letters ( using writing paint of Ist quality)or figures (Block, Roman, Italic or Indian) n.exc 30cm height complete all as specified & directed.

M&L for preparation of old treated wood and wood based materials, of any description and girth, not otherwise described, and treated with one coat of creosote oil complete all as specified & directed.

Taking down chowkat or frame with shutters (without taking off shutters from the frame) not exceeding 1.5sqm each and making good to disturbed surfaces and removing from site of work complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkat or frame with shutters (without taking off shutters from the frame) exceeding 1.5sqm but not exceeding 4.0sqm each and making good to disturbed surfaces and removing unserviceable materials from site of work complete all as specified and directed by the Engineer-in-Charge.

S & F, 35mm thick, second class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24(a); complete fixed to frame all as specified & as directed.

S & F, second class hard wood for small fittings such as brackets of any type latch and hinge blocks, shaped door and window stops and like, including all necessary labours, articles n exc 200 cu cm each complete all as specified and directed.

S&F, 3mm thick sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5sq. m in each pane complete all as specified and as directed

S&F, Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with tinned tacks, or stainless steel wire staples complete all as specified & directed

Material & Labour for plain cement concrete (1:3:6), type C-1, (using 20mm graded crushed stone aggregates) as in bed block, blocks for holdfasts, benching slightly rounded or chamfered angles & throating etc including necessary use & waste of form work complete all as specified and directed.

S & F mild steel hold fast for chowkats and other similar articles conforming Fe-290 Gde-E-165 complete all as specified and as directed

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old of any description and girth not otherwise described and treating small articles such as holdfasts with tar or coal tar black paint area not exceeding 0.1Sqm each complete all as specified and as directed.

S & F, anodised aluminium alloy curtain harrison rails with fixing brackets , stops, rollers etc complete all as specified and directed.

S&F Galvanised steel wire netting 0.91 mm dia and 12 mm size of mesh for lathing , fixed with tinned tacks of wire staples to wooden frame in wall including all laps, cutting and waste complete all as specified and directed.

Supply & Fixing mild Steel work in tubular trusses/steel columns including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St.-240 complete all as specified and directed.

Supply & Fixing for rolled mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with out any attachment conforming to Fe:410-W(Gde-E-250 ) quality-A complete all as specified and directed.

Taking down carefully copper/ aluminium point wiring (light, fan, call bell, socket or power) complete, including fittings and fixtures such as switches, ceiling rose, pendants, holders, regulators, sockets, light fitting etc. & removing from site and making good the disturbed surfaces of wall, ceiling etc. complete all as specified and directed

M & L for point wiring with FR PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and including PVC casing & caping terminated in PVC block 50 mm deep (sunken) for fixing of switches, sockets, fan regulators etc (PVC box and casing/capping of required size will be measured and paid under relavent item) for the following: - (a) One light point controled by one one way 5 Amp switch

M & L for point wiring with FR PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and including PVC casing & caping terminated in PVC block 50 mm deep (sunken) for fixing of switches, sockets, fan regulators etc (PVC box and casing/capping of required size will be measured and paid under relavent item) for the following: -(a) One fan point controlled by one , one way 5 Amp switch

M & L for point wiring with FR PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and including PVC casing & caping terminated in PVC block 50 mm deep (sunken) for fixing of switches, sockets, fan regulators etc (PVC box and casing/capping of required size will be measured and paid under relavent item) for the following: - (a ) One 5 pin socket outlet 05 Amp on independent board .

M & L for point wiring with FR PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and including PVC casing & caping terminated in PVC block 50 mm deep (sunken) for fixing of switches, sockets, fan regulators etc (PVC box and casing/capping of required size will be measured and paid under relavent item) for the following: -(a ) One 5 pin socket outlet 05 Amp on same board .

All as per item No167 here-in-before,for one 15 Amps socket outlet but using 2.5 sq mm,copper conductor with 1.5 sq mm,PVC insulated single core cable for earth continuity conductor.

S & F Switch piano, flush type single pole, one way 5 Amp

S & F Socket outlet 2 in 1, 3 pin, 5 Amp

S & F Switch socket combination 2 in 1, 5 Amp flush type

S & F Switch socket combination 5A/ 16A, 5 in 1flush type

S & F stepped type electronic fan regulator flush type

Supply & fix ceiling rose, 3 terminals, surface bakelite, /PVC/Polycarbonate.

S&F PVC/polycarbonate Angular lamp Holder insulated body with back plate angle type suitable for batten complete all as specified and directed by Engr-in-charge .

S&F LED bulb 10 watt self ballastted retrofit type lamp with PBT body shell and DC Diffuser CCT 6500K with fitting complete all as specified and as directed.

Supplying & fixingLED tube light fitting, 1 x 18 watt bipin holders, connector block etc. complete with all accessories internally pre-wired with and including 18 watt retrofit tube rod with batten and connecting the same to ceiling rose with using copper conductor 23/0.0076 flexible twisted twin core cable ,and fixing the light fitting to walls / roof complete all as specified & directed Make: Havells or equivalent

S & F Ceiling fan 1200 mm sweep with all accessories Make: Havells or equivalent

Supply & Fixing MS clamp made of flat iron size 25 x 6 mm including nuts, bolts and 'S' hook complete all as directed by Engineer-in-Charge.

S & F metallic exhaust fan 300 mm sweep,240 Volts, with louvre including necessary connection with three core round flexible copper wire of 1sqmm connector to fan, minimum 1m lenghth complete all as directed of Make:Havells/crompton/orient/bajaj.

S&F single pole and neutral DB wall mounting type,240 Volts,8Way with 200 Amps rated bus bar,double door suitable for fixing MCB's including connecting etc and taking down U/S DB ,main switch complete.

S & F MCB SPN 6 Amps to 32 Amps 240 volts Make: Havells or equivalent

S & F MCB SP 6 to 32 Amps 240 volts Make: Havells or equivalent

Supply & fix single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 10 KA 20 Amp MCB complete all as directed by Engineer-in-Charge.

Supply and fixing Water heater storage type, electric,capacity 25 litres.complete all as specified and directed by Engr-in-charge.

M & L for providing sub main wiring with two single core 4.0 sq.mm (nominal area) PVC insulated flame retardant unsheathed multi-stranded copper conductor cable 1100 volts grade drawing through PVC casing-capping complete including 2.5 sq. mm PVC insulated unsheathed multi-stranded flame retardant single core copper conductor cable for earth wire including taking down/ removing old one and making good disturbed surfaces of walls, floors, etc, complete all as specified and directed. [Note : (i) PVC casing capping shall be measured & paid separately here-in-after as supply only (ii) Two runs of single core 4.0sq.mm multi-standard copper cable and one run of 2.5sq.mm earth wire shall be measured as one run length. (iii) Extra length of cable required for connection to DBs/MCBs shall deem to be included in unit rate quoted by contractor against the item. (iv) Earth wire run inside the casing capping].

S & F LED building security light fitting 25W new generation energy saving and environmental friendly long life LED street light made up of pressure diecast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOPOPENINg seperate driver compartment with IP65 protection and impact resistance of IK07. Make: Havells or equivalent

Material and labour for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to galvanized iron earth lead wire 4mm dia, (main earthing lead ) by means of galvanized bolts, nuts and washers all as shown in electrical plate no 5 of MES Schedule Part-I (1991) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 15 mm dia GI pipe light grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia light grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1 for earth pit and 40 mm thick pre-cast RCC cover in 1 : 2 : 4 type B1 with 3 Nos 8 mm dia TMT bars both ways complete all as specified & directed by Engineer-in-Charge.

Material and labour for brick protection using old size sub class ‘B’ new bricks, laid flat dry but jointed, laid length wise perpendicular to the axis of cable all as specified and directed.

Taking down old unserviceable any size of LT cable and Supply and laying, jointing, testing and commisioning LT XLPE/PVC cables, PVC insulated, PVC Sheathed armoured LT 1100 volt grades 16 Sqmm 2 core heavy duty with aluminium stranded conductor through pipes, induct, on poles, in trenches etc.

Supply and laying 25 mm bore GI tubing light grade laid in trenches for cable protection.

Supply and fixing of 20 mm bore GI tubing, medium grade with all new fittings as required complete fixed to walls and ceilings or laid in floors/trenches including testing complete all as specified and directed.

Supply and fixing of25 mm bore GI tubing, medium grade with all new fittings as required complete fixed to walls and ceilings or laid in floors/trenches including testing complete all as specified and directed.

Supply & Fixing in repair 20mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms) complete all as specified and directed.(MAKE: Prayag)

Supply & Fixing Gun metal, gate valves, with iron wheel head, suitable for 20mm bore dia of pipes, Screwed both ends for iron pipe or for union including taking out old one complete all as specified and as directed.

Supply & Fixing Gun metal, gate valves, with iron wheel head, suitable for 25mm bore dia of pipes, Screwed both ends for iron pipe or for union including taking out old one complete all as specified and as directed.

Use and waste of formwork with fair finished flat, concrete surfaces such as soffits of suspended slab, such as roof slabs, floor slabs, landings and similar work, n.exc 200mm thick curved/circular surfaces of concrete complete all as specified and directed.

Removal of surplus excavted soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above starting point complete all as specified and directed.

M/S BHARAT AND CO

M/S CHANDAN ENTERPRISE

M/S BORAH BROTHERS

M/S CHAKRA GOHAIN

M/S JANATACONSTRUCTION

Construction House

M/s. Chanda Construction