SPL REPAIR OF BLDG No. P-106 BLOCK OF 20 SINGLE OFFRS ACCN (CENTRAL AMC MESS) AT AHRR UNDER GE E/M RR HOSP DELHI CANTT-10

Amount

Demolition of brick work or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified.

M&L for brick work with sub class 'B' Bricks (using old size bricks) straight or curved on plan exc 6m mean radius built in CM 1:6, complete all as specified and as directed.

M&L for brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified & directed.

M&L for 15mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6, finished even and fair without using extra cement, complete all as specified & directed.

M&L for 15mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:4, finished even and fair without using extra cement, complete all as specified & directed.

M&L for rendering 5 mm thick in cement and sand mortar 1:3 on concrete surfaces of ceiling, including finishing the surface even and fair without using extra cement complete all as specified.

M&L for preparation of newly plastered surfaces of walls and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed by Engr-in-Charge. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for preparation of newly plastered surfaces of ceilings and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed by Engr-in-Charge. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor

M&L for preparation of newly plastered surfaces of walls and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of exterior grade weather proof paint over one coat of primer, complete all as specified and directed by Engr-in-Charge. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor

M&L for complete removal of existing treatment from internal surfaces of walls by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed by Engr-in-Charge. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for complete removal of existing treatment from internal surfaces of ceiling by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of oil bound distemper over one coat of primer, complete all as specified and directed by Engr-in-Charge. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor.

M&L for complete removal of existing treatment from from external surfaces of walls by electrically operated grinder, washing and filling of holes with filler material and applying 1-2mm thick cement base wall care putty on the whole surface to achieve smooth, even & uniform surface including grinding with sand paper and levelling of surface and applying two coats of exterior grade weather proof paint over one coat of primer, complete all as specified and directed by Engr-in-Charge. Note: (a) All works shall be done mechanically through authorised applicator only. (b) Authorised applicator of paint manufacture shall have valid authrisation letter from the manufacturer (minimum regional HQs) issued not earlier than 30 days from start date of the said finishing work. (c) The contractor shall provide application for testing and certification of finishes by paint manufacturing firm/ their authorised applicator. (d) Cost of all above aspects shall be deemed to be included in quoted rate of the contractor

Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing) and rubbish off the premises, complete all as specified & directed.

M&L for vitrified glazed ceramic coloured tiles 8-9mm thick (square/ rectangular) polished of light shade, area of each tiles not exceeding 0.42 sqm but not exc 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed or bedding layer in cement mortar (1:6) for laying floor finishes, complete all as specified.

M&L for vitrified glazed coloured tiles 8-9mm thick (square/ rectangular) polished of light shade, area of each tiles not exceeding 0.42 sqm but not exc 1.00 sqm, in dado/ skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10 mm thick screed bed or bedding layer in cement mortar (1:4) to receive wall tiles, complete all as specified.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.09 sqm but not exceeding 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over & including 15mm thick screed bed or bedding layer in cement mortar (1:6) for laying floor finishes, complete all as specified & directed.

M&L for coloured glazed ceramic wall tiles as in vertical surfaces of size 600 mm x 300 mm x 7 to 8 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10 mm thick screed bed or bedding layer in cement mortar (1:4) to receive wall tiles, complete all as specified & directed.

M&L for 16-18mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over & including 10 mm thick screed bed or bedding layer in cement mortar (1:4) to receive dado/ skiritng etc, complete all as specified & directed.

M&L for 16-18mm thick granite (of any type) tiles as in flooring, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete, over & including 15mm thick screed bed or bedding layer in cement mortar (1:6) for laying floor finishes, complete all as specified & directed.

Providing edge moulding to 18-20mm thick granite stones of any description of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete

M&L for mirror polishing on marble/ granite/ kota stone work where ever required to give high gloss finish, complete all as specified & directed.

S&F for heavy duty coloured paving tiles of size 300mmx300mmx8-9mm thick, exterior grade, set and jointed with neat cement slurry and pointed in colour or white cement to match, laid over and including screed bed and bedding layer of mortar 15mm thick in CM 1:6 for laying floor finishes, complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, complete all as specified.

M&L for cement concrete 1:5:10, type E2 (using 40mm graded aggregate), as in sunken flooring, complete all as specified and directed.

M&L for rendering 15mm thick cement screed in CM 1:4 on brick or concrete surfaces using integral water proofing (3% by weight) for floor and sides of wall, complete all as specified and directed.

Supply only Integral water proofing compound, complete all as specified.

M&L for sealing of pipe peneration toilets core cutting & sunken slab treatment in following stages:- supply and apply solvent free, moisture intensive epoxy resin based patch repair putty Sikagrade-694F (I), yeild : 0.6 Ltr/kg suitable for submerged condition having compressive strength of 40 N/mm2 (1 day) according to IS 9162-1979 on pipe peneration surface. The putty shall be appllied to a groove thickness of minimum 20mm on pipe peneration joints to concrete etration of surface of sunken portion and M&L for glass fibre reinforced acrylic modified cementtitious coating system as Top cost : Sika Top Seal - 107 @ 1.5 kg/sqm over reinforcement : Sika Fab-1 over base coat : Sika Top Seal-107 1.5 kg/sqm etc all as specified and directed system should have compressive strength 20 N/mm2, Bond strength 2.0 N/mm2 including providing 20mm bore GI pipe spout pipe, complete all as specified and directed. Note: (a) Entire work shall be carried out through manufacturer or its authorised representive. (b) The contractor shall furnish a 10 years guarantee for effectiveness of water proofing.

M&L for 25mm thick PCC 1:2:4 (using 20mm graded stoe aggregate) as in sub base to floor tiles, complete all as specified.

Taking down chowkats or frames including shutter (without taking off shutters from the frame) area not exc 1.50 Sqm each, complete all as specified.

Taking down chowkats or frames including shutter (without taking off shutters from the frame) area exc 1.50 Sqm but n.exc 4.00 sqm each, complete all as specified.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of grade Fe-410- W (Gde- E-250) quality-B, complete all as specified.

Providing & fixinng factory made 100% Solid WPC (Wood Polymer Composite) door frame of size 125 mm x 65 mm double rebated made from Wood Polymer Composite (Single Extruded Process) material comparising of virgin PVC polymer of K value 57-60 ( Suspension Grade ), Calcium Carbonate and Natural Fibers (Wood Powder/ Rice Husk/ Wheat Husk ) and Non toxic additives fabricated with meter Joints after applying PVC solvent Cement & screwed with full body treaded star headed screws having minimum frame density of 780 kg/ cbm, having good screw holding capacity (screw withdrawal strength of (Min 990N), Minimum Compressive Strength of 58 N/mm2, Modulus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof , water / Moisture Proof & Fire retardant & Fixed in position with SS Dash Fasteners / Hold Fast of required dia and length, all as per specifications drawings as directed by the Engineer-In-Charge.

S&F factory made single extruded WPC (wood polymer composite) soild plain flush door shutter of 30mm comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fibers (wood powder/ rice husk / weat husk) and non toxic additives (max toxicity index of 12 for 100gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having min frame density of 750 kg/cum, screw withdrawl strength of 2200 N (face) 1100N (edge) min compressive strength of 58 N/MM2, modulus of elasticity 900 N/MM2 and resistance to spread of frame of class a category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed countersunk SS screw complete all as specified and directed

Providing & fixing 30mm thick factory made wire mesh solid WPC door shutter consisting of Density 600 Kg /Cum, door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the MS tube. Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings.

S&F butt hinges, medium weight, stainless steel 100mm size, complete all as specified and directed

S&F 150mm size stainless steel handles, complete all as specified and directed

S&F 150mm long stainless steel barrel tower bolts, complete as specified and directed

S&F 250mm long stainless steel sliding door bolt with staple (bolt type) and fixing clips and fixing bolts and sliding bolts, complete all as specified and directed

S&F 150mm floor door stopper of stainless steel body and tongue with hard drawn steel spring fixed in floor complete all as specified and directed

S&F aluminium powder coated chowkhat of 100x44x1.5mm section with rebate complete frame, complete all as specified and directed.

Supplying, fabricating & fixing aluminium door shutters with powder coating (minimum thickness of powder coating 50 micron), vertical stile of door shutter of size 85mm x 44.45mm x 1.5mm thick, top, middle and bottom rail of size 85mm x 44.45mm x 1.5mm thick and fixing plain/ tinted sheet glass or ACP sheet with aluminium beading and rubber gasket/ beading as directed. One mortice lock for alumium door (each) and three nos aluminium hinges of size 100mm and two alumium tower bolts of 150mm size for each door fixed with rawl plug includimg rectification of floor/ wall to match the existing surface, complete all as specified. (Cost of sheet glass/ ACP sheet shall be measured and paid seperately).

Suuply only 4.8mm thick glass (plain or tinted) fixed with beading in aluminium frame in square exc 0.5 sqm in each pane, complete all as specified & directed.

Supply only 4mm thick aluminium composite panel (ACP) sheet including necessary clips, rubber packing and aluminium beading, complete all as specified & directed.

Supplying, fabricating & fixing aluminium powder coated (minimum thickness of powder coating 50 micron) glazed three track sliding window of frame 100x44x1.5mm and sliding shutter of section 40mmx19mm including 3mm thick sheet glass, ordinary quality exceeding 0.36 sqm in each pane, in two track shutter and in one track stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, all fittings and locking arrangement with each moving leaf, complete all as specified.

S&F aluminium Deco grill with powder coating (minimum thickness of powder coating 50 micron), 7.5 mm size DG-102, fixed to E/H frames, 1.5mm thick, bar size 6.2mm and 7.5mm thick in required sizes, complete all as specified and directed.

S&F 12mm thick toughned glass as in hinged doors, automatic sliding doors, partitions and similar work including cutting to shape, drilling holes required, clips, sliding roller, automatic sensor, hinges, pivots, joining cleats, glazing clips, silicone packing in each door including all necessary patch fittings, required for automatuic sensor doors, complete all as specifed and directed.

S&F stainless steel handle 450mm long fixed to 12mm thick toughned glass door with and including all fixing accessories i.e. bolt, washer, adhesive etc, complete all as specifed and directed.

S&F stainless steel door lock, glass to glass type, suitable for 12mm frameless toughned glass door with and including all fixing accessories i.e. bolt, washer, screws, adhesive etc, complete all as specifed and directed.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specifed and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm plain colour PVC sheet on back face with particle board core, supplying & fixing in frame at site as per specification & drawing, complete all as specified and directed.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5mm wood grain printed & edges will be painted to match with printed colour PVC sheet reinforced with MS square tube S&F in opening as per specification and drgs, complete all as specified.

S&F 100 mm long butt hinges, medium weight, cold rolled mild steel and fixed, complete all as specified.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

S&F 150 mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets, fillets etc, and removal of debries from site, complete all as specified and directed.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, all as specified & directed.

M&L for gypsum board 12mm thick in ceiling fixed with screw as per manufacturers instructions in any position and design/ pattern, levels including two coats of oil bound distemper over two coats of cement base wall care putty including necessary taping of joints etc, complete all as specified & directed.

M&L for exposed GI frame/ grid system duly powder coated for module size of 600 x 600 mm suitable for lay-in aluminium/ metal/ mineral fiber ceiling ties having main T runner of 24mm size, suspended at 1200 mm C/C and cross T runner of 24 mm size, suspended at 600 mm C/C with interlocking arrangement to form grid of 600 x 600 mm , perimeter runner/ channel of 15 mm size, main and cross T runner supported by 4mm dia GI rod from slab/ roof, wall angle etc with and including all fixing accessories and making good of disturbed wall surrfaces with POP and one coat of oil emulsion distemper, as required to match the existing surfaces, complete all as directed .

M&L for metal false ceiling, lay-in type, 0.5mm thick having tegular edge profile , duly powder coated, perforated type with glass fiber acoustic fleece, suitable for false ceiling grid/ frame module of 595 x 595mm size, complete all as specified and directed. (Note : The grid/ frame shall be measured and paid for separetly).

S&F in repairs stainless steel curtain rod 20-22mm dia of including brackets, side knobs etc, fixed to walls, complete all as specified and directed.

Dismantling boarding any description, fixed in any position with screws, complete all as specified & directed.

S&F 18/19mm thick PVC moulded solid board, one side pre-laminated & other side plain for cabinets boxes, shutters etc with shelf and shutters, full size fitted under/ above kitchen cooking platform and other platform, complete all as per manufacturer's instruction and as specified & directed.

S&F soft closing clip on hinges, full/ half overlay type, of stainless steel of size as per site requirement or all as directed.

S&F 100mm size stainless steel handles fancy type with matt finish fixed with screws, complete all as specified & directed.

S&F stainless steel telescopic type ball bearing slide and runner, suitable for drawers of size as per site requirement, complete all as specified & directed.

Taking up or down 15mm bore steel tubing and connections, complete all as specified & directed.

All as per ser item No. 67 here-n-before but 20mm bore of pipe.

All as per ser item No. 67 here-n-before but 25mm bore of pipe.

All as per ser item No. 67 here-n-before but 40mm bore of pipe.

S&F 15mm bore tubes, 'medium grade', galvanised, with all fitting; (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors, complete all as specified.

All as per ser item No. 71 here-n-before but 20mm bore of pipe.

All as per ser item No. 71 here-n-before but 25mm bore of pipe.

All as per ser item No. 71 here-n-before but 40mm bore of pipe.

S&F in repair white colour, 1st quality vitreous china washdown water closet pan wall mounted fancy type including concealed cistern with flush plate and including white seat cover, complete all as specified and directed. (Make: Jaquar or equivelnt of other makes.).

S&F in repair white vitreous china wash hand basin table top of size 470mm x 470mm x 110mm of white colour complete including necessary brass chromium plated waste coupling and bottle trap, complete all as specified. (Make: Jaquar or equivelnt of other makes.).

S&F in repair wash basin mixer, with out pop up waste system, long body, made of cast copper alloy, chromium plated fancy type, suitable for 15 mm bore pipe, complete all as specified and directed.

S&F in repairs bib taps, cast copper alloy, fancy type, with crutch or butterfly handle, chromium plated, screwed down, screwed for iron pipe or for brass ferrule of 15mm bore, complete all as specified & directed.

S&F in repairs single lever wall mixer with provision for overhead shower with hand pipe on shower side, connecting legs and wall flanges, complete of Cat part No. ORM-10143N of Jaquar or quivalent of other makes).

S&F in repairs stop valves, cast copper alloy, fancy type, chromium plated with long shank & cup with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15mm bore, complete all as specified & directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 600mm, all as specified & directed.

S&F in repair tubular towel rail stainless steel chromium plated 20 mm dia D type 60 cm long between flanges, including brackets and fixed to walls, all as specified and as directed by Engineer-in-Charge.

S&F in repairs chromium plated shower rose 125mm size with or without swivel joints with arm, complete all as specified.

S&F in repairs soap dish, brass CP any type, fixed to plugs with chromium plated brass screws, complete all as specified and directed.

S&F in repairs SS glossy finish grating of square shape of size 150mmx150mm with hinge type openable jali of 100mm dia size with and including fixing with cement mortar to floor/ nahani trap etc, complete all as specified & directed.

S&F toilet roll holder with flap made of cast copper alloy chromium plated fancy type, complete all as specified.

S&F towel ring round/ square shape of suitable size made of cast copper alloy chromium plated fancy type, complete all as specified.

S&F in repairs health faucet (ABS body) mild dteel chromium plated for 15mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connections and fixed in position, complete in all respect as specified.

S&F in repairs 200mm x 200mm corner glass shelf with bracket and fixing accessories, complete in all respect as specified

S&F in repairs 300mm x 300mm corner glass shelf with bracket and fixing accessories, complete in all respect as specified

Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks etc, complete all as specified & directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls, complete all as specified & directed.

S&F 320mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or floors, complete all as specified & directed.

S&F 110mm bore PVC (SWR) bends any radius, complete all as specified & directed.

Taking up cast iron water mains (including all fittings) 100mm bore, with spigot and socket ends and lead joints including burning out joints and recovering lead, all as specified.

Taking up cast iron water mains (including all fittings) 80mm bore, with spigot and socket ends and lead joints including burning out joints and recovering lead, all as specified.

S&F 110 mm bore cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors, all as specified.

S&F 110 mm bore cast iron soil, waste and vent pipes in any length with or without ears, with lead joints, fixed to walls, all as specified.

S&F 75 mm bore cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors, all as specified.

S&F 75 mm bore cast iron soil, waste and vent pipes in any length with or without ears, with lead joints, fixed to walls, all as specified.

S&F 100mm bore of pipe bends (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified.

S&F 100mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, all as specified.

S&F 75mm bore of pipe bends (any radius), diminishing pieces or tapers (larger bore measured), all as specified.

S&F 75mm dia outlet cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), all as specified.

S&F cast iron 'P' or 'S' trap of 100mm size as per IS 1729-2002 ISI marked, fied with lead joint in floor, all as specified.

S&F 75mm bore cast iron cowl, all as specified.

S&F 100mm bore cast iron cowl, all as specified.

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified.

S&F in repair 1000 litres capacity double layer, rotational molded, polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe, complete all as specified and directed.

S&F in repairs 40mm bore pipe gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

Dismantling brick tiles or terracing tiles single layer on roofs, complete all as specified & directed.

Demolition of mud/ mud phuska in roofs any thickness, including plastering and leaping if any and cleaning the roof surfaces with wire brushes and removal of mud /mud phuska to a distance exc 250 M and n exc 500 M, complete all as specified directed.

M&L for cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in roof padding including finished even & smooth without using extra cement, complete all as specified and directed.

M&L for priming roof surfaces and applying water proofing treatment over roof including preparation & cleaning of roof surface comprising of the following complete all as specified & as directed:- (a) Applying oil bound bituminous primer at the rate of 0.4 Ltrs/sqm as per IS 3384-1986 on prepared surfaces. Surfaces shall be kept free till the moment, the primer is impregnated and the solvent oil in primer is evaporated. (b) Applying one coat of hot straight run bitumen @ 1.2 Kg/sqm of grade 85/25 confirming to IS-73. (c) Laying 3 mm thick APP polymeric water proofing membrane of weight not less than 3.6 kg/sqm, black finish reinforced with non woven polyester matt, with a thermo fusible finish, torching overlaps with a propane or a butane gas torch, with a overlap of 75 mm at sides and 100 mm at the ends and sealing including applying a coat of cold emulsion bituminous primer, all as per manufacturer's instruction including preparation of surface. Note: Water proofing treatment shall be got carried out by the manufacturer or their authorised applicators. Contractor shall give 10 years guarantee for effectiveness of water prrofing treatment. 2.5% of workdone amount of this items shall be retained from the contractor payment for a period of 10 years reckoned from date of physical completion of the work or in lieu contractor may deposit bank FDR for the said tory for 10 years which shall be released by GE ont he expiry of satisfactory completion fo 10 years period, complete all as specified and directed.

M&L for pre-cast PCC tiles machine pressed of size 25cm x 25cm x 20-22 mm thick, over and including 20 mm thick screed bed in cement mortar 1:6 and joints grouted flush in cement mortar 1:3 mixed with integral water proofing compound as per manufacturer instruction, complete all as specified & directed.

M&L for chipping of spalled and loose concrete and cleaning rust from reinforcement by sand blasting scrubing down concrete surfaces with wire brushes cleaning with water allow to dry and applying a layer of Zinc rich epoxy primer as an anti rust on all exposed reinforcement followed by a layer of binding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited and applying two layers of guniting over steel welded mesh 2mm dia of wire and aperture 75mm. Total thickness of guniting not exc 40mm (Avg thickness) in cement mortar 1:2 using OPC 53 grade cement mixed with polycreate mixture @ 2% by weight of cement or as per manufacturer's instruction and finally applying cement plaster over guniting surface of required thickness to give even, uniform and smooth finishes confirming to proper geometrics in cement mortar 1:3 to match the existing surfaces as in sides, soffits of the slabs, chajjas, fins, facias, parapets, linetls, columns and beams etc complete including necessary scafolding, shuttering, chasing to brick work or RCC members at any height upto 6 storied buildings including removal of all small trees/ shrubs etc , complete all as specified and directed.

Dismantling asbestos cement (corrugated, semicorrugated etc.) sheets in roof coverings etc complete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Dismantling mild steel or wrought iron work of any description not otherwise provided for, complete all as specified and directed.

S&F steel work in tubular trusses/ square pipes including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS1161-1979 grade St.-240, all as specified and directed.

M&L for preparation of new steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) of 200mm internal dia of pipe complete all as specified and directed.

S&F 200mm bore of pipe reinforced concrete pipe, class NP-2, laid in trenches and jointed complete with collars all as specified and directed.

M&L for concrete bed to drain pipes 1:3:6 type C2 including packing under and haunching against the side of pipes after they are laid and tested, complete all as specified and directed.

M&L for returning, filling in including spreading levelling watering and well ramming in layers n exc 25cm hard/dense soil all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete, complete all specified & specified.

M&L for PCC type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) as in coping, band, plinth coarse, plinth band etc incl use and waste of form work and finishing the surface smooth with slightly rounded or chamfered angles and throating as ordered complete all as specifed and directed.

Demolition of reinforced cement concrete as in drains or manhole covers of any description and in any position not otherwise specifically provided for complete all as specified and as directed

S&F 75mm thick factory made RCC precast heavy duty manhole covers with MS frame including reinforcement as per manufacture/ IS 12592, hot dip galvanized lifting hook for lifting overall cover of size exc 0.50 but not exc 1.00 sqm each , complete all as specified and directed.

Taking down old unserviceable point wiring with and including existing conduit / batten type (light, fan, socket or power point) complete such as tube light any type switches, ceiling rose, pendent holder, regulator and socket etc and removing the material from site with chasing and cutting surface of wall / floor/ ceiling etc complete all as directed.

Taking down existing sub main wiring aluminium/copper 4/6 sqmm.

M&L for point wiring concealed type with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable connected to common earth and earth dolly with suitable copper lugs drawing into and including rigid non-metallic PVC surface conduit of 20mm dia or higher, medium grade complete with all PVC conduit accessories, GI metal flush box of 1.60 mm thick suitable for modular/conventional switches/sockets/fan regulators with cover plates, blanking plates, brass screws, cup washers etc including all cutting / chases etc in walls and making good to the disturbed surfaces to match the existing complete all as specified and directed for the followings :- Note - All accessories likes modular top cover plate/ hylum sheet cover plate, Metal flush box, screws etc as applicable will be included in quoted rates.

One light point/ceiling fan/exhaust fan point controlled by one switch

One socket outlet 5 Amps controlled by one switch on same board

One socket outlet 5 amps controlled by one switch on independent board

One bell point controlled by one bell push switch

All as per srl item No. 133 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for 15 Amp power point.

All as per srl item No. 133 here in before but point wiring for one light point controlled by two Nos of two way switches

Material and labour for Sub main wiring with 2 run of 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in and including PVC conduit with wall thickness 1.6mm thick and including 4 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB/Panel to sub DB complete all as directed. Note : 1. The two run of 4 Sqmm wire, one run of 4 Sqmm wire and 1 mtr PVC conduit pipe will be measured as one unit.

Material and labour for Sub main wiring with 2 run of 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked, drawn in and including PVC conduit with wall thickness 1.6mm thick and including 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB/Panel to sub DB complete all as directed. Note : 1. The two run of 6 Sqmm wire, one run of 6 Sqmm wire and 1 mtr PVC conduit pipe will be measured as one unit.

S&F modular switch 6 Amps, one way, one module 240 volts complete all as specified and directed.

S&F modular switch 16 A, 1 module,240 volts complete all as specified and directed.

S&F modular socket, 3 pin 6 Amps,240 volts, 2 module complete all as specified and directed.

S&F modular socket 6/16 A, 5 pin, 2 module, 240 volts complete all as specified and directed.

Supply and fixing in replacement electronic fan regulator, Modular type, socket size and making all necessary connections complete all as directed.

Supply and fixing in replacement Modular type Bell push switch, single pole, one way, 5/6 Amps complete all as directed.

S&F in replacement Modular switch, 6 amps two way,SP,230 volts AC all as specified.

Supply and fix in replacement of Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps with and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed.

Supply and fix in replacement of MCB protected modular AC/Geyser box complete with and including 6 pin socket, plug top, modular cover plate, mini MCB SP 20 Amp capacity and PVC gang box etc, complete all as specified and directed by by Engineer-in charge.

S&F in replacement LED tube light fitting 20 watt (CW) , 4 feet long in extruded aluminium batten with high efficient LEDs available in milky diffuser and Color Rendering Index (CRI>70), IP20, correlated Color Temparature (CCT- 5700K to 6500K) , PF>0.9 and Voltage rated 220V to 240V complete all as directed.

Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing in repair LED luminaire (2'x2' LED fittings), 36 watt, 220 V AC recessed/surface mounted type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

Supply and fix in replacement Building security light with high efficient high power LED street light 40 watt with lens with pressure die cast aluminium housing and enclosed with toughened glass IP-66 including service bracket 1.2 mtr long by using 32 mm bore GI pipe and fixing accessories ( Clips, Fasteners, Nut, Bolts etc) Temparature (CCT- 5700K to 6500K) , PF>0.9 and Voltage rated 220V to 240V etc complete all as directed.

S&F in replacement Bathroom Vanity lights 15W, lighting fixtures Black Modern/ Bedroom Wall Lighting for Mirror (Warm White), High transmission with acrylic cover, should give perfect spotlight for makeup, shave, read or display products, back painted iron body with acrylic plating surface is durable, safe and easy to clean, PF>0.95 and voltage rated 220V to 240V etc complete all as specified and directed.

S&F in replacement decorative surface mounted wall light with contemporary sleek design suitable for 9W LED lamp B22 base including LED Bulb of 9W (Warm White) and including all other fixing accessories complete all as specified and directed.

Taking down carefully ceiling fan of any size, sealing cable end, dismantling blades & removing fan and blades to store complete all as directed.

M&L for painting of ceiling fan complete with synthetic enamel paint by spraying including filling cavaties with filter one coat after cleaning all as directed

Hanging only with fixing accessories ceiling fan and connecting with and including 3 core flexible copper cable from ceiling rose to fan all as directed

Supply and fix in replacement Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc and making all necessary connections complete all as directed.

All as srl item no 26 here in before but SPN 04 way type.

All as per srl item No. 26 here in before but of 415 V, 8 Way VTPN suitable for incorporation of MCCB, MCBs and isolators etc all as directed by Eng- in Charge

M&L in replacement MCB 6 to 32 Amp, B Curve type, 10kA, single pole with over load and short circuit protection complete all as directed.

Supply and fixing in replacement MCB, SPN type of 40 to 63 amps capacity, 240V, 10 KA with all connections complete all as directed.

Supply and fixing in replacement MCCB 415 Volt, 16kA,4 pole of 125 Amp capacity with all connections complete all as directed.

Taking down carefully exhaust fan any size, seling cable and depositing to store complete all as directed.

Fixing only exhaust fan and connecting up including provision of cable from ceiling rose to fan all as directed.

Supply & fix in replacement Bell Buzzer, Ding Dong single phase AC Supply 230 volts,

Taking down water heater storage type of any capacity carefully and refixing complete with new fasteners and all accessories complete all as directed.

M/s VINOD KUMAR SHARMA (BID ID -3156797)

M/S Rohit Enterprises (BID ID -3163329)

SHYAM ENTERPRISES (BID ID -3158031)

BEHAL TRADERS (BID ID -3158006)

M/S Chhavi Constructions Co (BID ID -3158144)

Vipul Construction (BID ID -3163523)