Rehabilitaion of Kulasekaraperi Big Tank in Thirumalaupram Village of Sivagiri Taluk in Tenkasi District.

Amount

Dismantling, clearing away and carefully stacking material useful for reuse for any thickness of brick or stone masonry in Cement Mortar walls under 3 (Three) metres high complying with standard specification and as directed by the Engineer.

Earth work excavating and depositing on bank with a initial lead of 10 m & initial lift of 2m in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size of boulders hard gravelly soil complying with standard specification and as directed by the departmental officers. SS 20B

Refilling the excavated earth in layers not exceeding 23cm thickness and watering to OMC (Optimum Moisture content) and compaction of each layer to 95% of proctor Density through deployment of appropriate compaction equipment (8-10T power roller) vibratory power roller of short width ( 0.90m width drum) power roller or vibratory power roller/fuel operated or electrically operated, vibratory plate compactors, ensuring compaction of designed bund section including side slopes etc., complete complying with standard specification and as directed by the Departmental Officers.

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size of boulders and hard red gravelly soil depositing on bank including shoring, strutting and baling out water wherever necessary and refilling the sides of foundation with excavated soil other than sand in layers of not more than 15cm thick, well rammed, consolidated and depositing the surplus earth in places as shown by the departmental offixers with an initial lead of 10metres and initial lift of 2metres and clearing, levelling the site etc., complte complying with standard specification and as directed by the departmental officers.

Supplying and filling with CS sand of each layer not more than 15 cm thick including consolidation etc complete and as per the technical specifications directed by the Engineer in charge of the works For sluices, weirs and retainig wall etc., complete complying with standard specification and as directed by the Departmental Officers.

Providing and placing in position of plain Cement concrete of grade M15 using hard well graded aggregates with the nominal maximum size of coarse aggregate of 40mm; weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 15 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers.

Providing and placing in Position of Plain cement concrete of grade M15 using hard broken stone aggregate of maximum nominal size of 20mm 40% and 40mm 60% to IS specified grading mixing by mixer machine including dewatering the placement site,laying the concrete in layers and in bays vibrating,compacting and finishing the surface with all leads and lifts watering curing to attain the profile and strength as specified in the drawing for various depth and height below and above ground level etc complete as directed by the Engineer in charge of work complying with the standard specification (with vibration).

Providing and placing in position of plain Cement concrete of grade M15 using hard broken granite coarse aggregates with the nominal maximum size of 20mm; weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 15 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers.

Providing Steel centring for RCC Slabs, beams or plain surfaces including strutting upto 3.29 m high using MS sheets, 10 guage thick of size 90cm x 60cm, Stiffened with Ms angles of size 25mm x 25mm x 3mm laid over silver oak joists of size 10 cm x 6.5 cm spaced at 90 cm c/c and supported by casurina props of 10 cm to 13cm dia spaced at 75 cm c/c and removing the centring and shuttering after specified period without damaging the concrete laid, etc., complete complying with standard specification and as directed by the Departmental Officers. (The retrieved material should be taken back by the contractor)

Centering without strutting

Centering with strutting

Providing and laying in position of Standardised Concrete Mix M25 in accordance with IS 456-2000 using 20 mm down graded hard broken granite stone jelly for all RCC items of works with minimum cement concrete of 350 kg/m3 and maximum water cement ratio of 0.55 with about (5 cum) 7730 kg of 20 mm machine crushed stone jelly and with about (3.30 cum) 5156 kg of 10 - 12 mm machine crushed stone jelly and with about (4.79 cum) 7670 kg of sand weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 25N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specification and excluding the cost component of providing rigid and smooth centering and shuttering wherever necessary for various depths below ground level and various heights above ground level as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position complying with standard specification

Providing and laying in position of Standardised Concrete Mix M20 in accordance with IS 456-2000 using 20 mm down graded hard broken granite stone jelly for all RCC items of works with minimum cement concrete of 325 kg/m3 and maximum water cement ratio of 0.55 with about (5 cum) 7730 kg of 20 mm machine crushed stone jelly and with about (3.30 cum) 5156 kg of 10 - 12 mm machine crushed stone jelly and with about (4.79 cum) 7670 kg of sand weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 20N/mm2 at 28days) including dewatering of placement site by bailing/pumping and by diverting wherever necessary laying the concrete in layers and in bays, Vibrating, compacting and finishing the surface water curing so as to attain the profile and strength specified in the approved drawing and specification and excluding the cost component of providing rigid and smooth centering and shuttering wherever necessary for various depths below ground level and various heights above ground level as per the direction of the Engineer complete in all respect but excluding the cost and placing of reinforced grill in position complying with standard specification

Supplying fabricating and placing in position of Ribbed tor steel bars of various diameter for all Reinforced Cement Concrete works including cost of rods, binding wir, Labour Charge for cutting the rods to the required length, bending, tying and fixing in position complete for various height below and above ground level etc., Complete complying with standard specification and as directed by the by the Engineer in charge of work.

Providing and placing in position of plain Cement concrete of grade M20 using hard well graded aggregates with the nominal maximum size of coarse aggregate of 20mm; weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 20 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers. without vibration Wearing coat Sluice & Weir) (with out vibration)

Supplying and fixing new cut stone fully dressed to size all faces and set in cement mortar 1:3 (One cement and three sand by volume) mixed mechanically in approved mixer) including all incidental charges such as finishing, curing etc., complete complying with standard specification and as directed by the Departmental Officers

Fabricating, supplying and erection of Screw Gearing steel shutters of size 0.85 m x 1.05 m with consists of skin plate made out of 8 mm thick mild steel plate and horizontally stiffened with 100 mm x 50 mm x 6 mm steel channel (ISMC) at an interval of not more than 0.5 m and vertical stiffeners made out of same section at an interval not more than 0.6 m and provided with 8 mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Groove Channels of ISMC 100mmx100mmx10mm mild steel angle for required height up to 2.50 m including welding hold fast of size 40 mm x 40 mmx 6 mm mild steel angle 3 numbers on both sides. Providing Sill Beam of 150mm x 80mm x 6mm, 0.85 m length and providing of 63 mm screw rod made of mild steel duly machined and fully threaded to suite the Head set assembly with required height up to 5.10m and required holes. Fixing the screw rod to the shutter gusset plate with required bolts and nuts in proper alignment to the Head Set. Providing of Top Beam made up of 200 mm x 100 mm x 6 mm (ISMB 200) for the length of 1.80 m duly drilled to suite the Head Set assembly with required bed bolts made out of 25 mm mild steel round rod duly threaded with suitable anchorage arrangements to the height of 0.6 m with necessary fish plate made out of 16 mm mild steel plate of size 0.2 m x 0.3 m 2 numbers with require bolts. Providing Head set assembly medium duty with Hexagonal nut (approximate 50 kg) made up of cast iron including moulding, machining and Hexagonal nut threaded to suit screw rod provided with thrust bearings for smooth operation. The whole shutter assembly should be painted with two coats of anti-corrosive black paint over one coat of red oxide primer paint.Erecting Shutter assembly by Durky post and Chain block. The rate is inclusive of all materials, labour charges including Lathing, Drilling, Welding, Gas cutting, Hydraulic bend removing of M.S. rod, hire charges of Crane and also inclusive of cost of covering plate, Foundation bolts, all bolt and nuts, conveyance to this site, Loading and unloading charges, Grease packing, Lubricating oil, Operating key, Locking arrangement and checking the Shutter operation etc., complete as directed by the Departmental Officers. The rate is Excluding GST.

For sluice size of shutter 0.85m x 1.05m

Providing and fixing weep holes of 110mm dia pvc pipes of working pressure 4kg/m2 to a required length for protection wall, abutment and wing wall including cost of conveyance of all materials to work site including cost of labour charges for 90cm spherical back fill arrangements with 110mm dia and 20mm size hard granite broken stone charges at the peripery, the labour charges for fixing and to drain the back fill etc., complete complying with the standard specifications and as directed by the departmental officers.

Random rubble masonry in Cement mortar 1:4 (One cement and four sand) using hard granite stones and bond stones including simultaneous pointing of the exposed surface with same mortar and all incidental charges such as bailng out water curing, finishing complying with standard specification.

using Old stone 60%

using New stone 40%

Gravel packing 15cm thick for cement concrete block revetment or apron including stacking watering and consolidation etc., complete complying with standard specification and as directed by the Departmental Officers

Rough stone dry packing for revetment and apron using hard granite stones obtained from approved sources including the cost of new wedges for filling the gaps etc., complete complying with standard specification and as directed by the Departmental Officers.

using Old stone 60%

using New stone 40%

Clearing light jungle and disposing of the same as directed by the Engineer complying with standard specification.

Earthwork in all soils except hard rock requiring blasting and conveying for formation of bund with lead of 0 to 100 metre deploying earth moving machineries and tippers including benching, formation of bunds, breaking clods, sectioning etc. complete including extra watering and compaction of earth fill layers to specified density of 95% of proctor density through deployment of appropriate compaction equipment (standard 8-10 ton power roller; short width drum vibratory power roller; vibratory power roller; fuel-operated vibratory plate compactor of adequate capacity, as per space available for compaction etc., complete complying with standard specification and as directed by the Departmental Officers.

Supplying demarcation R.C.C. pre cast post in Cement concrete M20 grade with well graded aggregates and the nominal maximum size of coarse aggregate of size 20 mm of size 0.15 x 0.15 x 1.20 M and fixing the post 40 Cm depth below ground level, the post includes using 4 numbers of 8 mm RTS main rod to a length of 1.325 M, using 6 mm MS 9 numbers as strrups with steel centering and painting the post with enamel paint to a height of 0.80 M alround the post etc. complete and conveying the post to the site of demarcation boundary such as tank bund and foreshore including earth work excavation for foundation in HSC, and the post embedded by using Cement concrete M10 grade with well graded aggregates and the nominal maximum size of coarse aggregate of 20 mm, as per the direction of the Engineers and complying with standard specification.

Pointing with CM 1:3 over the old revetment and retaining wall portion including curing and removing weeds in the old revetment and retaining wall portion and clean removal plaster from wall and revetment in hanging condition etc., complete as per the technical specifications and as directed by the Engineer in charge.

Fabricating, supplying and erection of Screw Gearing steel shutters of size 0.85 m x 1.05 m with consists of skin plate made out of 8 mm thick mild steel plate and horizontally stiffened with 100 mm x 50 mm x 6 mm steel channel (ISMC) at an interval of not more than 0.5 m and vertical stiffeners made out of same section at an interval not more than 0.6 m and provided with 8 mm thick mild steel gusset plate of required size on both sides fastened with rust free bolts and nuts etc. Groove Channels of ISMC 100mmx100mmx10mm mild steel angle for required height up to 2.50 m including welding hold fast of size 40 mm x 40 mmx 6 mm mild steel angle 3 numbers on both sides. Providing Sill Beam of 150mm x 80mm x 6mm, 0.85 m length and providing of 63 mm screw rod made of mild steel duly machined and fully threaded to suite the Head set assembly with required height up to 4.90m and required holes. Fixing the screw rod to the shutter gusset plate with required bolts and nuts in proper alignment to the Head Set. Providing of Top Beam made up of 200 mm x 100 mm x 6 mm (ISMB 200) for the length of 1.80 m duly drilled to suite the Head Set assembly with required bed bolts made out of 25 mm mild steel round rod duly threaded with suitable anchorage arrangements to the height of 0.6 m with necessary fish plate made out of 16 mm mild steel plate of size 0.2 m x 0.3 m 2 numbers with require bolts. Providing Head set assembly medium duty with Hexagonal nut (approximate 50 kg) made up of cast iron including moulding, machining and Hexagonal nut threaded to suit screw rod provided with thrust bearings for smooth operation. The whole shutter assembly should be painted with two coats of anti-corrosive black paint over one coat of red oxide primer paint.Erecting Shutter assembly by Durky post and Chain block. The rate is inclusive of all materials, labour charges including Lathing, Drilling, Welding, Gas cutting, Hydraulic bend removing of M.S. rod, hire charges of Crane and also inclusive of cost of covering plate, Foundation bolts, all bolt and nuts, conveyance to this site, Loading and unloading charges, Grease packing, Lubricating oil, Operating key, Locking arrangement and checking the Shutter operation etc., complete as directed by the Departmental Officers. The rate is Excluding GST.

ANTONY CONSTRUCTION (BID ID -1435445)

CHELLADURAI G (BID ID -1435497)