PROVN OF 01 X TOILET BLOCK WITH WASHROOMS AT E AMF OF RVC CENTRE COLLEGE AND SPL REPAIR IN OFFR MD ACCN AT ROORKEE ROAD UNDER AGE BR I, AGE BR II AND AGE EM I OF GE NORTH MEERUT CANTT

Amount

Surface excavation in soft/loose soil n exc 30 cm deep and averaging 15 cm deep and getting out complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m depth in soft/ loose soil for foundation etc or for shaft, wells, manholes,pier holes etc n exc 10 Sqm on plan and not exc 1.5 m in depth and getting out and levelling of bottom surface to required level complete all as specified and directed.

M&L for Earth filling under floor with excavated soil including earth spreading in layers n.exc 30cm thick watering and rolling and finishing to reqd size and shape etc complete all as specified and directed.

Returning, filling in including spreading ,levelling watering and well ramming of soft/loose soil in layers n exc 25 cm thick each complete all as specified and directed.

Removing excavated material ( spoil ) not exceeding 50 m distance and depositing where directed at a level n exc 1.5 metre above the starting point complete all as specified and directed.

M&L for concrete bed to drain pipe including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm dia in PCC 1:3:6 type C2 using 40 mm graded stone aggregate all as specified & directed.

M&L for SGSW drain pipe 150 mm internal dia laid in trenches , jointed and tested all as specified & directed.

M& L for providing Cement concrete 1:4:8 Type D 2 (using 40 mm graded crushed stone aggregates) ,in foundations, filling and mass concrete complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type BO, (using 12.5mm graded stone aggregate) sub base as in floor to receive tiles complete all as specified.

M&L for providing cement concrete 1:2:4 Type B 1 (using 20 mm graded crushed stone aggregates) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs hold fast water troughs, filling in pressed steel door frame and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work complete all as specified and directed.

M&L for providing reinforced cement concrete design mix M-25 (using 20 mm graded crushed stone aggregates) foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for providing reinforced cement concrete design mix M-25 (using 20 mm graded crushed stone aggregates) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for providing reinforced cement concrete design mix M-25 (using 20 mm graded crushed stone aggregates)as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for providing reinforced cement concrete design mix M-25 (using 20 mm graded crushed stone aggregates)as in beams, cantilevers, bressummers, lintels over 1.5m clear span complete all as specified and directed.

M&L for providing reinforced cement concrete design mix M-25 (using 20 mm graded crushed stone aggregates) as in chajja complete all as specified and directed.

M&L for laying 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in floor/plinth protection, cement concrete surfaces finished even & fair without using extra cement complete all as specified and directed.

M &L for Brickwork with fly ash bricks old size bricks straight or curved on plan exc 6m mean radius built in Cement mortar 1:6 complete all as specified and directed.

M &L for Brickwork with fly ash bricks old size bricks straight or curved on plan exc 6m mean radius built in Cement mortar 1:4 complete all as specified and directed.

M&L for Brickwork with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for cutting chases, pinning in, in brick wall, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring. etc. and making good, cutting not exceeding 10cm girth complete all as specified and directed.

M&L for providing formwork to sides of concrete foundations, footings, bases of columns raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces of concrete flat complete all as specified and directed.

M&L for providing formwork to soffits of suspended slabs such as roof slab , floor slabs , landing ; chajjas and similar work not exc 200mm thick; flat fair finished surfaces of concrete flat complete all as specified and directed.

M&L for providing formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, exc 1.5m clear span cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surfaces of concrete flat complete all as specified and directed.

M&L for providing formwork to sides of square ,rectangular or polygonal pillars, posts, struts, piers, and columns rough finished surfaces of concrete flat complete all as specified and directed.

M&L for providing formwork flat fair finished surfaces to edges of concrete flats, breaks in floor cills, railing etc & similar works exc 10 cm but n.exc 20cm wide complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges,. Steel peg stay, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter and builders hard ware fittings from frames) exc 1.5 sqm but not exc. 4 sqm each, complete all as specified and directed. Note :- Rate also incuding in this item for necessary cutting down / taking out hold fasts from the existing concrete / brick work and making good the disturbed surfaces with match existing surfaces.

Taking down chowkats or frames with shutters (without taking off shutter and builders hard ware fittings from frames) n. exc 1.5 sqm each, complete all as specified and directed. Note :- Rate also incuding in this item for necessary cutting down / taking out hold fasts from the existing concrete / brick work and making good the disturbed surfaces with match existing surfaces.

Supplied and fixed powder coated (thickness of powder coating not less less than 50 micron aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleats for fixing etc. omplete all as specified and directed.

S&F 75mm size, 4 levers, brass mortice lock vertical type and including two keys complete all as specified and directed.

S&F powder coated (thickness of powder coating not less than 50 micron) anodised aluminium sliding widnow and ventilator shutters, side hung type without sash bars aluminium section weighing 0.55 Kg/RM with and including necessary joining cleats, glazing, clips, rubber packing, anodised aluminium snap beading for fixing glass panes screws anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type B-21 100mm long (2 No), extruded anodised aluminium alloy fabricated type handles of size 100mm 1 Nos complete all as specified and directed Note :- Glass panes in panes in panels shall be measured and paid separately.

S&F brass barrel tower bolts,with cast or sheet berrel and rolled or cast bolt length of bolt 200mm with dia of shoot / bolt complete all as specified and directed.

S&F aluminium anodised barrel tower bolts,with cast or sheet berrel and rolled or cast bolt length of bolt 150mm with dia of shoot / bolt complete all as specified and directed.

S&F 300 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed. complete all as specified and directed.

S&F extruded brass handles, febricated type polished, size of handle in mm 125 complete all as specified and directed.

S&F extruded aluminium anodised handles, febricated type polished, size of handle in mm 150 complete all as specified and directed.

S&F butt hinges of 100 mm size, cast brass with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and directed.

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing shown on page 178 of SSR Part-II complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electro galvanised,width of flap (when open ) 40 mm. complete all as specified and directed.

S&F in repairs stainless steel fancy type curtain rod 25mm dia, complete all as specified and directed.

S&F in repair aluminiun (die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed. complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples including necessary beadings complete all as specified and directed.

S&F mild steel work as for framed work such as grills gratings, etc., with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed baluster; walk ways; railings; framed work of water tanks and similar work including necessary riveting and / or welding conforming to Fe 290 (Gde-E 165) complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia quality conforming to Fe- 415, Fe 500 or Fe-550 as in steel reinforcement for concrete complete all as specified and directed. Note :- Weight of binding wire shall not be considered for measurement and payment purpose.

All as per Srl item No 45 here-in-before but 5mm to 10mm dia in stirups, spacers and binders

M&L for cutting grooves in brick wall 75mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 after inserting water proofing membrane complete all as specified and directed.

M&L for preparing ,cleaning new concrete / plastered surface providing 15mm thick bedding layer of cement mortar 1:4 mixed with water proofing compound and applying evenly a tack coat @1.20 kg/Sqm with 85/25 industrial bitumen over a coat of bitumen primer @ 0.30 liter/Sqm and laid with 3mm thick APP modified polymeric water proofing membrance with non-woven polyester rainforced and applying a tack coat of 85/25 industrial bitumen @ 1.2 kg per Sqm and finish the surface with aluminium paint at top @ 0.2 kg/Sqm as per manufacturer's instructions. Weight of membrane shall not be less than 3.6 kg/Sqm unrolled and bonded to substrate with side and end laps 75mm & 100mm as per manufacturer's instructions. complete all as specified and directed. Note :- The WPT work shall be got done through manufacturer's authorised applicator only under strict supervision of manufacturer's technical representative.

Taking down old existing water proofing treatment from top of RCC/arch slab including taking down of concrete padding or plaster and raking out joints of arch slab and hacking the top of RCC slab, cleaning with water and dispose off rubbish upto 200 meter complete all as specified and directed

M&L cement concrete 1:2:4 type BO (12.5mm graded stone aggregate) as in padding concrete in sunken floor etc mixed with liquid water proofing compound 200ml in 50Kg cement complete (WPC shall be measured and paid separately).

M&L for cleaning the roof surface / the treatment shall be throughly free of laitance, scales, oil or any other loose material. It should be made free of any sharp objects. Cleaning of PCC Shall be done with wire brushing to attain smooth levelled surface. Cracks shall be rectified, filled using dual shrinkiage compensatedRepair Mortar and dried for 72 hours before laying the liquid applied membrane. (a) Application of paint two component Epoxy Primer (Resin & Hardener) on the cleaned surface for bonding of Polyurethane with the existing concrete surface 33% water dilution is recommended with the pure mixed primer. The primer mixing ratio will be 1:3 (Resin : Hardner) Supplying, providing and applying waterproofing treatment to area with single component highly elastomeric seamless cold applied modified PU coating complete as per manufacturer's specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have a dual combination of 280% elongation. Material coverage 1.2kg / sq.mt. Make : Asian Paints/ Thermax.

(b) Treatment of pipe entry points : Preparing the inside surface of core and PVC / MS Pipe by roughening using suitable sand paper to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Packing the gap using free flowable non shrink cement polymer based grout up to the surface of the bore while the bonding agent is in tacky state. the periophery of PVC pipe should be sealed with Hybrid PU Sealant or dual shrinkage compensated Micro concrete Note : Will be done when and where ever required. Note : (i) The work under this item shall be carried out by the authorized applicator of Manufacturer by using modern techniques. The contractor shall also furnish warranty of quality, finish work and effectiveness of waterproofing treatment under this item for a period of 10 years from the date of completion along with manufacturer warranty of material for the same period . (ii) Contractor is required to deposit 100% CA quantity to the Engr-in-Charge, within 15 days of acceptance of contract.

M&L for rounding to edges of stone slabs two edge full round, such as in steps, cooking platform and other similar situation complete all as specified and directed

M & L Non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors etc. set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed".

M & L for light shade vitrified tiles 10mm thick (minimum), (square / rectangular) polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in flooring set and jointed in neat cement slurry and pointed in white or coloured cement to match the clour of tiles and over and including 15mm thick screed bedding in CM (1:6) complete all as specified and directed".

M & L for light shade vitrified tiles 10mm thick (minimum), (square / rectangular) polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, in skirting / dado set and jointed in neat cement slurry and pointed in white or coloured cement to match the clour of tiles and over and including 10mm thick rendering in CM (1:4) complete all as specified and directed".

M&L for Glazed ceramic coloured tiles of size 350mmx 250mmx7 mm / 450mm x 350mm x 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including rendering 10mm thick in cement mortar (1:4) complete all as specified and and directed

S&F factory made glazed and skeleton shutters 35 mm thick 1st class hardwood open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); for doors and fitted to chowkats complete all as specified and directed.

Supply and fixed gun metal globe valves, 20mm dia, with iron wheel head ,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S&F angular valve, 15mm bore dia, cast copper alloy, CP with long shank and cup(concealed type) screwed down,high pressure with crutch or butter fly handle,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S & F for 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S & F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

M&L 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane in metal frame complete all as specified and directed

M&L 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n. exc 0.5 sq. m in each pane in metal frame complete all as specified and directed

M&L for exterior grade, coloured, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick (ULTRA or as indicated in Appendix 'C' to P.S.) set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc. complete all as specifed and directed.

M&L for 20 mm thick machine cut Granite stone slab GREEN / BLACK table rubbed polished and round edges as in cooking plateform, steps and window cills and like in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigmen to match with shade of granite laid over and including 10mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base complete all as specified and directed.

Dismantling of floor, hearth or wall tiles / terrazzo including cement mortar bedding (but not backing),removal servicable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete vertical surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M & L for applying 15mm thick rendering unsing ready mix plaster bags in CM 1:4 on brick / concrete surfaces of external walls finished even and fiar, using water proofing compound @3% by weight of cement of as per manufacturer instructions, complete all as specified an directed. Note:-Water proofing compound shall be measured and paid sepratly Note Contractor is required to deposit ready mix bags for 100% CA quantity to the Engr-in-Charge within 15 days of acceptance of contract.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified and directed.

M&L for 10 mm thick screed bed in cement mortar 1:4 as in roof mixing with WPC mixing with water proofing compound by 3% by weight of cement or as per manufacturers instructions complete all as specified and directed. Note :- Water proofing compound will be measured and paid seperately.

M&L for preparing the new plastered surfaces and applying two coats of Oil emulsion distemper over a coat of primer including 2mm thick JK / Birla wall care putty and using roller for painting complete all as specified and direcrted.

M&L for preparation of old plastered surfaces of walls includig complete removal and applying two coats of acrylic exterior emulsion point (viz weather proof paint) over a coat of primer including 2mm thick JK / Birla wall care putty and using roller for painting complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls includig complete removal and applying two coats of oil emulsion distemper over a coat of primer including 2mm thick JK / Birla wall care putty and using roller for painting complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls includig complete removal and applying two coats of cement base paint over a coat of primer including 2mm thick JK / Birla wall care putty and using roller for painting complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer including 2mm thick JK / Birla wall care putty complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of acrylic exterior emulsion point (viz weather proof paint) over a coat of primer including 2mm thick JK / Birla wall care putty and using roller for painting complete all as specified and directed.

M&L for preparing the new plastered surfaces and applying two coats of white wash on ceiling complete all as specified and direcrted

M&L for preparing the new plastered surfaces and applying three coats of white wash on wall complete all as specified and direcrted

M&L for preparing the new plastered surfaces and applying three coats of white wash on ceiling complete all as specified and direcrted

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying two coat of white / tinted synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of old painted steel surface of any description over 10 cm in width or girth and applying one coat of white / tinted synthetic enamel paint complete all as specified and directed

Taking up or down GI water tubing 15mm bore and connection including cleaning serviceable pipes for refixing and unserviceable removal from the site complete all as secified and directed

Taking up or down GI water tubing 20mm bore and connection including cleaning serviceable pipes for refixing and unserviceable removal from the site complete all as secified and directed

Supplied and fixed GI water tubing 15 mm bore medium grade with all fittings fixed to walls and ceiling or laid in floors including cutting screwing and waste etc complete all as specified and directed.

Supplied and fixed GI water tubing 20 mm bore medium grade with all fittings fixed to walls and ceiling or laid in floors including cutting screwing and waste etc complete all as specified and directed.

Supplying and laying of 16mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fitting in trenches and wall complete all as specified and directed

Supplying and laying of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fitting in trenches and wall complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined to gether with solvent cement, suppling & fixing in the frame at site as per specification & drawing on srl page No 174 of SSR Part-II complete all as specified and directed.

S&F in repair vitreous china ware EWC combined pattern complete with internal fittings as specified and directed by Engineer-in-Charge. Make : Cera of Cat Part No S101314L or equivalent in Parryware / Hindware

S&F vitreous china ware EWC padestal type complete with internal fittings as specified and directed by Engineer-in-Charge.

Supply and fixing vitreous china urinal bowl, flat back of size 465x355x265mm (minimum) white with grating and unionfor discharge pipe (excluding flushing cistern,flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm lng brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusiveof fixing supply pipe to flushing cistern, trap and waste pipe complete all as specified and directed.

Dismantling of old water tank exc 250 Ltr & n.exc 500 Ltr capacity and Supplied, hoisted and fixed inposition rotational moulded polyethylence water storage tanks IS : 12701 - 1996 marked (cylindrical vertical with closed top) of 500 Ltrs capacity with and including 20mm dia Ball valve high pressure of PTMT with apoxy aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed.

Supplied, hoisted and fixed inposition rotational moulded polyethylence water storage tanks IS : 12701 - 1996 marked (cylindrical vertical with closed top) of 500 Ltrs capacity with and including 20mm dia Ball valve high pressure of PTMT with apoxy aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed.

S&F butt hinges of 100 mm size, Medium weight, cold rolled mild steel. complete all as specified and directed.

Supply and fixed stop valves, 15mm bore dia, cast copper alloy, CP fancy type with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle,screwed down both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S&F in repairs bib tap, C P cast copper alloy fancy type with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule of 15 mm bore and fixed complete all as specified and directed.

Supply and fixed stop valves, 15mm bore dia, cast copper alloy with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle,screwed down both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

Supplied and fixed in repairs brass chromium plated wall mixer with over head shower for mixing Hot & Cold water high pressure, screwed down for 15mm bore iron pipe complete all as specified and directed. Make:- Cera Cat part No :- F-1017401, Pearl Cat Part No ARI-015, Hindware Cat Part No F740022

Supplied and fixed in repairs CP towel rack 24" size complete all as specified and directed make Jaquar cat part No 1181 or equivelent in Parko / Gem complete all as specified and directed

Supplied and fixed in repairs 15mm dia bib cock long thread fancy type,brass CP with wall flange fixed as in repair make-Jaquar Cat part No -5041 complete all as specified and directed.

Supplied and fixed in repairs CP toilet paper holder brass CP conforming to the sample kept in the office of Engr-in-Charge complete all as specified and directed.

S&F in repairs towel ring 200mm dia chromum plated fancy type conforming to the sample kept in the office of Engineer-in-Charge.

Supplied and fixed in repairs CP soap dish make-Jaquar cat part No- ACN 1131 complete all as specified and directed.

Supplied and fixed CP soap dish conforming to the sample kept in the office of Engr-in-Charge complete all as specified and directed.

Supply and fixing PVC low level flushing cistern of 10 Ltr capacity syphonic action type with inlet ball valve, float and handle including PVC brackets for mounting of cistern complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supplied and fixed 110mm bore UPVC(SWR) pipes single socketed in any length with rubber ring joint, fixed to wall including stack clamps complete all as specified and directed.

Supplied and fixed 75mm bore UPVC(SWR) pipes single socketed in any length with rubber ring joint, fixed to wall including stack clamps complete all as specified and directed.

Supplied and fixed 110mm bore dia UPVC(SWR) pipes single socketed in any length with rubber ring jointed laid in tranches / under floor complete all as specified and directed.

Supplied and fixed UPVC (SWR) bends 110 mm bore complete all as specified and directed

Supplied and fixed PVC (SWR) 110 mm bore junction, single(single 'T') equal or unequal complete all as specified and directed

Supplied and fixed PVC (SWR) 75 mm bore vent cowl complete all as specified and directed

Supplied and fixed in repairs UPVC (SWR) floor trap 110 mm bore including jointing to waste pipe with cement solvent fixed in cement concrete complete all as specified and directed

Supplied and fixed UPVC (SWR) floor trap 75mm bore including jointing to waste pipe with cement solvent fixed in cement concrete complete all as specified and directed

Supplied and fixed UPVC (SWR) gully trap 125mm bore including jointing to waste pipe with cement solvent fixed in cement concrete complete all as specified and directed

Supplied and fixed in repairs super special colours vitreous china WHB, white, flat back size 580x430mm including pedestal & bracket etc. CP brass waste coupling 32mm dia, PVC waste pipe 32mm dia and PVC connection 450mm long high pressure with PTMT nut complete all as specified & directed. Make : CERA Cat No S2040113 & S2090106

Supplied and fixed vitreous china WHB, white, flat back size 550x400mm including cutting for and pinning in ends of bracket or erecting stand with and including angle iron brackets, duly painted with two coats of synthetic enamel paint over one coat red oxide zinc chrome primer and providing cast copper alloy capastan head C.P brass pillar tap fency type 01 No 15mm bore, CP brass waste coupling 32mm dia, PVC waste pipe 32mm dia and PVC connection 450mm long high pressure with PTMT nut complete all as specified & directed.

S&Fin repairs sinks with drainage board made of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

M&L in repair 18/19mm thick solid WPC board, exterior grade, prelaminatedone side with decorative choice laminations and other side balanceing white lamination, fixed with screws to WPC frame work in cup boards, rebated or flat edges fancy handle, magnite lock complete all as specified and directed

S&F in repairs plate rack of stainless steel, sheet 1mm thick for kitchen overall size 1200x900x180 mm ,fixed with plugs and washers on wall complete all as specified and directed.

S&F glass shelf assembly 60 cm long , 5.5 mm thick glass, 12cm wide, CP guard and fixed to wooden plug with CP screws and cup washer as specified complete all as specified and directed.

M&L for construction of Soakage well, excavated in ordinary soil, foundation PCC 1:3:6, walls of honey combed and solid brick in CM, RCC cover slab in M-25 design mix, filling work with brick bats including intercepting chamber, screen chamber complete of size 3.00m dia x 6m (4.5m effective depth) deep as directed by directed by Engr-in-Charge. Drg No Ref TD HQ CEBZ Drg No TD/309 sheet 1/4, 2/4, 3/4 & 4/4.

M&L Construction of septic tank for 25 users with sludge chamber including necessary earth work, brick work in CM 1:4 and precast RCC cover slab in M-25 Design mix having 6mm thick MS plate embedded all around reinforced cover complete all as specified and shown on drg No TD-217 sheet 1/7 to 7/7 and directed.

S&F in repairs Corner glass shelf (with brackets) set of three Make : Jaquar Cat Part No ACN 1173

Supply and fixing vitreous china squatting pan, Orissa' pattern, size 580 x 440mm white, with integral foot rests with and including cast iron 'P' or 'S' trap and setting the trap and pan in and including PCC 1:4:8, type D-2 minimum 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, making all connections complete all as specified and directed.

Dismantling of cast iron, PVC or reinfrced concrete drain pipes jointed in CM and taking out of trenches if required for 110mm and 75mm bore of pipe complete all as specified and directed

Demolition of brick work or rubbled stone masonry including all quoins arches , pillars etc built in cement mortar and including removal from the site complete all as specified and directed.

Demolition of cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) and including removal of debris & rubbish from the site complete all as specified and directed. Note : Stone slabs / tiles and hard core of any description shall not be measured & paid under this item.

Dismantling of framed steel work of any description as in purlins, rafters, grills etc. complete all as specified and directed.

------------------BLANK----------------

S&F in repairs brass chromium plated health faucet with 1 meter long SS braided rubber hose pipe and wall hook complete all as specified and directed Make - Cera Cat Part No F-8030301

S&F fancy type brass CP hot and cold wash hand basin mixer 15mm bore screwed down high pressure with long screwed shanks and fly nuts, screwed to iron piep complete all as specified and directed.

S&F PVC Bath cabinet with mirror 18" x 22" x 4.25". Make : commander, Prayag or equivalent complete all as specified and directed

Taking down carefully any type of battens or conduit point wiring with conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, pendent light fittings, MCBs / isolators, fan regulators, tube light fittings etc removing material from site and making good disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as directed by Engineer - in - Charge.

Material and labour for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, stranded, FRLS PVC insulated, unsheathed, copper conductor cable in and including PVC concealed conduit of any size/dia complete with all accessories/fittings, brass screws, washer etc, sunk zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and earth duly complete all as specified and directed for the followings :- (a) One tube light/Bulb/ street light point controlled by one, one way switch 05 / 06 Amps.

All as per Srl item No 139 here-in-before but One fan / Exhaust fan point controlled by one, one way switch 05 / 06 Amps.

All as per Srl item No 139 here-in-before but One 3 pin, 05 / 06 Amps socket outlet point on independent board controlled by one, one way 05 / 06 Amps switch.

All as per Srl item No 139 here-in-before but One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch.

All as per Srl item No 139 here-in-before but One Bell point controlled by one, one way switch 05 / 06 Amps.

All as per Srl item No 139 here-in-before but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15 / 16 Amps socket outlet point on independent board.

All as per Srl item No 139 here-in-before but with 4sqmm multi stranded PVC insulated, unsheathed copper conductor,FR, cable in and including in rigid PVC conduit 20 mm dia or higher medium grade

Supply and fix switch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified & directed by Engr-in-Charge

Supply and fix in socket outlet 5 pin, 05 / 06 Amps flush type 240 volts complete all as specified & directed of maby Engr-in-Charge .

Supply & fixing of socket outlet 3 pin, 05 / 06 Amps and 3 pin 15 / 16 Amps (2 in 1 Multipurpose) 240 volts complete all as specified & directed of make Cona/Legrand/SSK.

Supply and fix in switch piano flush type, 15 / 16 Amps single pole, one way 240 volts complete all as specified & directed by Engr-in-Charge

S&F stepped type type electronic fan regulator flush type complete all as specified and directed

Supply and fixing bell push flush type , 5 amps , 240 volts complete all as specified and directed

Supply and fixing Bell,AC , 230 volts ,Single poler Cona/Anchor complete all as specified and directed

Supply & fixing of ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified & directed by Engineer -in- Charge.

Supply & fixing lamp holder (Angular / Straight), insulated body, with back plate complete all as specified and directed

Supply and fixing LED lamp 2 pin 9/10 watt complete all as specified and directed

Supply and fixing LED light fitting 1x22/25 watt,220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high output diffuser 2 feet,10 watt 220V, AC decorative type with driver holder and LED lamp including connecting up with three core flexible copeer conductor cable of suitable size complete all as specified and directed.

Supply and fixing in repairs 1x36/40W LED Building security light energy saving & environmental friendly long life luminaire with high power LEDs as light source and electronic driver including security light brackets of 32 mm dia GI pipe medium grade upto 1.2 mtr long bend to shape at 100-120 degree including flat iron clamps and Suitable nuts and bolts grouted in wall including all material required for fitting all as specified and directed.

S&F in repairs Fancy light cast Aluminum polyurethane paint(with prior Treatments)bracket with round base with LED Lamp 05 to 11 watts compete all as specified and directed.

------------------BLANK----------------

Material and labour for sub main wiring with 06 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor cable with and including continuous earth wire of size 06 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dolly including taking down old u/s wiring & incl all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 12 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer - in -charge.

Supply and fixing MCB, SP, AC, 240 volts 'C' curve capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed.

Supply & fixing Double pole Isolator 240V, 40A, and making connections complete all as specified & directed.

S&F TPN DB, 4 way, 415 V, double door type suitable for mounting incoming and outgoing MCB’s double pole/single pole,complete all as specified and directed.

S&F in repairs, TPN MCB 100 Amp, 50 Hz, 415 V with rupturing capacity 10KA 'C' curve ISI Marked, and making connections complete all as specified & directed.

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with TMT Bars 8mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed.

Supply and fixing Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, RPM 1200, copper winding of sweep 250mm complete all as specified and directed

supply and fixing Exhaust fan steel body AC single phase 230V of size 300mm sweep with blades and frame and louvers complete all as specified and directed

Supply and fixing fan ceiling complete with blades, down rods, electronic regualtor and accessories ,230V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE.Five Star rated with Brushless direct current motor (BLDC) complete all as specified and directed

Supply, Install, Test & Commissioniong, Water Resistant / Splash Proof (IPX-4), Whirlflow technology, Electric Water Storage Heater (Geyser) 25 Ltrs capacity, AC, 230V, Vertical Type, 5 Star Rated, ISI Marked, Energy Efficient, having Feroglass coated / Anode Rod protected inner container / Tank, Incoloy Glass Coated Heating Element, High Density PUF insulated, Multi Function Safety Valve, Fire Retardant ISI Marked Heavy duty 3 core cable with shock Resistant Plug Top, Temperature Sensitive LED indicators, Adjustable Temperature Setting, 0.8MPa high working Pressure, Complete including suitable size Anchoring / Grouting Bolts with Nuts & Washers, necessary grouting in PCC incl earthing testing for the Geyser, Colour : White, Make : Venus / Havells / Racold incl taking down old unserviceable one and depositing to MES all as directed.

Supply & fix PVC connections 15 mm size with PTMT nuts of length 450 mm suitable for hot & cold water connection complete all as specified and directed

S & F and grouting in wall sheet metal enclosure factory fabricated with single pole & neutral with a two pin and earth plug top and socket complete with one single pole MCB 20 Amps 240 volts complete all as specified and directed

Supply & fixing LED tube light fitting T/5 surface mounting poly carbonate 240 volts 20 watts, 6500K complete all as specified & directed.

Supplying & fix LED tube light fitting T/5 surface mounting poly carbonate batten 240 volts 10 watts, 6500K complete all as specified & directed. (Make - Havelles)

------------------BLANK----------------

S&L XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volt grade cross sectional area of 16 sqmm 2 core complete all as specified and directed.

------------------BLANK----------------

------------------BLANK----------------

Supply and spreading clean fine dry river sand in trenches for cushioning of under ground cable/ cable duct complete all as specified and as directed. Note: Only punned thickness shall be measured for payment purpose

M & L for fly ash brick protection length of brick shall be laid across the length of cable) complete all as specified and directed.

------------------BLANK----------------

GI light grade tubing 40mm dia laid in trenches, road crossing , pasing through pipe or laid in wall/pole complete all as specified and directed.

------------------BLANK----------------

Supply and fix sheet metal enclosure single pole & neutral for 240 volts 8 way with 200 Amp rated bus bar flush /surface mounting double door. complete all as specified and directed.

------------------BLANK----------------

Supply and fix MCB SPN 40 Amps, 240 volts, 50 Hz suitable for fixing in MCB DB 'C' series complete all as specified and as directed.

Arun Construction Co.