Rep and Ren. of Doctors Staff Qtrs of Runikhata 30 Bedded Hospital at Runikhata in Chirang District. (TN_30_2)

Amount

(A) Repair/Renovation of Hospital Building: Half brick masonary with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.2 Cement mortar 1:4 (1 cement: 4 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) 9.1.2 Sal wood.

Dismantling roofing including ridges, hips, valleys and gutters etc. and stacking the material within 50 metres lead of 15.28.1 G.S. Sheet

Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia meter with bitumen and G.I. limpet washers or with G.I. limpet washers filed with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal / vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 12.1.3.0. 63 mm thick with zinc coating not less than 275gm/m2

Providing ridges or hips of width 60 cm overall width plain G.S. Sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. Limpet and bitumen washers complete. 12.4.2 0.63mm thick with zinc coating not less than 275gm/m2

Providing and fixing flat pressed 3 layer medium density partice board or graded particle board (Grade I) IS: 3087 marked, in ceiling with necessary nails etc. complete (frame work to be paid separately): 12.25.1 12mm thick

15mm cement plaster on the rough side of single or half brick wall of mix: 13.2.1 1:4 (1 cement: 4 fine sand)

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 ce3ment: 3 coarse sand), finished with a floating coat of neat cement. 11.6.1 18mm thick

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of requored size with necessary screws, excluding panelling which will be paid separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) 9.5.1 Second class teak wood 9.5.1.2 30mm thick shutters

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting mix 1:2 (1 cement hardener mix: 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufactures's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer.

Finishing walls with Acrylic Smooth exterior paint of required shade 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

(B) Sanitary Installation for Hospital Building: Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required. 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm and 340 x 410 x 265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. Brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets cutting and making good the walls and floors wherever required: 17.4.3 Range of three urinal basins with 10 litre white PVC automatic flushing cistern

Providing and fixing wash basin with C.I. Brackets, 15mm C.P. Brass pillar taps, 32 mm C.P. Brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 17.7.1 White Vitreous China Wash basin size 630 x 450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing 600 x 450 m beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. Brass screws and washers complete.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 17.73.1. 450mm long towel rail with total length of 495 mm, 78mm wide and effective height of 88mm, weighing not less than 170 gms

Providing and fixing Chlorinated Polyviny Chloride (CPVC) pipes, having thermal stability fro hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge. Concealed work, including cutting chases and making good the walls etc. 18.8.3. 25 mm nomonal outer dia pipes

Providing and fixing Chlorinated Polyviny Chloride (CPVC) pipes, having thermal stability fro hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge. Concealed work, including cutting chases and making good the walls etc. 18.8.2. 20 mm nomonal outer dia pipes

Providing and fixing Chlorinated Polyviny Chloride (CPVC) pipes, having thermal stability fro hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-charge. Concealed work, including cutting chases and making good the walls etc. 18.8.1. 15 mm nomonal outer dia pipes

Providing and fixing brass bib cock of approved quality 18.15.2. 20 mm nominal bore

Providing and fixing Chlorinated Polyviny Chloride (CPVC) pipes, having thermal stability fro hot & cold water supply, including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer-in-charge. 18.9.8. 80mm nomonal inner dia pipes

Providing and fixing Chlorinated Polyviny Chloride (CPVC) pipes, having thermal stability fro hot & cold water supply, including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer-in-charge. 18.9.9. 100mm nomonal inner dia pipes

Providing and placing in position hand pump of approved quality for 40mm diameter G.I. Pipe complete with all accessories.

Providing and fixing G.I. Unior in G.I. Pipe including cutting and threading the pipe and making long screws etc. complete (New work) 18.46.8 80 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

PREMJIT BORO

PHUNGKHA BORGOYARY