SPECIAL REPAIR TO LOW TENSION OVERHEAD LINES AND DISTRIBUTION SYSTEM WITH CONNECTED ACCESSORIES IN ARMY AREA AT MOUNT ABU

Amount

Dismantling of old ACSR conductors from LT steel tubler pole/ RCC polecomplete all as specified and directed.

Material & Labour for LT Aerial Bunched cable of size 3x70 sqmm Phase conductor, 1x50 sqmm Neutral conductor and 1x55 sqmm Messenger Conductor complete all as specified and directed.

Material & Labour for LT Aerial Bunched cable of size 1x16 sqmm Phase conductor, 1x16 sqmm Neutral conductor and 1x25 sqmm Messenger Conductor complete all as specified and directed.

Material & Labour for Suspension hook of LT Aerial Bunched Cable complete all as specified and directed.

Material & Labour for Dead end clamp of LT Aerial Bunched Cable complete all as specified and directed.

Material & Labour for PG Connector of LT Aerial Bunched Cable complete all as specified and directed.

Material & Labour for Insulation piercing connector of LT Aerial Bunched Cable complete all as specified and directed.

Material & Labour for SMDB Box outdoor Horizontal type 3 phase and neutral to distribute LT Aerial Bunched Cable and fixed in RCC Pole complete all as specified and directed.

Material & Labour for SMDB Box outdoor type single phase and neutral (for Security Light) of LT Aerial Bunched Cable complete all as specified and directed.

Material & Labour for renewal of plate earthing for LT panel with galvanised mild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than 2.25 m below normal ground level) with the top edge of the earth plate at a depth not less than 1.5 m below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and incl GI earth strip 32 x 6 mm bolted (with GI nuts, bolts & check nuts) and riveted to earth plate electrode at one end and connected to metallic bodies of HT/LT equipments etc at the other, earth strip encased in and including 40mm bore GI medium grade pipe with all fittings from top of electrode to body of equipment fixed with and including 40 x 6mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from bottom of earth pit to top of electrode complete with earth pit in PCC 1:2:4 type B-O using 12 mm graded crushed stone aggregate, RCC cover, funnel, wire mesh including necessary excavation and earth work , etc complete all as specified and shown in electrical plate No 3 of SSR Pt-I.

-Ditto- all as per item No 25 above but using glavanised iron strip 25x4mm as earthing lead complete all as specified and directed by Engr-in-Charge

Dismantling old unserviceable LT concrete pole, any size and removing from site complete all as directed

Dismantling stay assembly complete, any type, any size complete making good disturbed surfaces and removing from site as per splecified and directed

Supply & errect in position 9.00 mtr long prestressed cement concrete poles of cross section 102x152mm at top and 102x289mm at bottem, class 10 conforming to IS-1678-1978 all as specified and directed.

Supply and fixing stay assembly comprising of stay bow glavanised 14mm dia x 400mm stay rod 16mmx1.80mtr long with nuts, bolts, washer, MS stay plate, two Nos thimble and clamps etc complete all as specified in electrical No-1 of SSR Part-I Note : Loop type insulator, excavation & earth work and concrete foundation shall be incuded in the qhoted rates.

Material & labour for cross arms, bracing, supports, back plate & clamps fabricated from structural steel section including nuts, bolts, washer cutting, welding bending cold or hot, drilling holes for bolts in any shape for bolts in any shape or size inclusive of painting with 2 coats of aluminum paint over a coat of primer complete all as specified

Taking down old Unsv bus bars chamber and Supply and install, testing and commissioning of Bus bar chamber of size 90 cm x 90cm x 40 cm outdoor type suitable for LT 415 volts 3 phase 4 wire system factory made cubical complete materialised dust and vermin proof (protection class IP 54), made out of 3.15mm thick MS sheet (CRCA) including factory made hinged type door both side opening with locking arrangement duly painted with two coats of synthetic enamel paint with powder coated finish over a coat of zinc chrome primer complete all as specified and directed by Engineer-In-Charge. the panel board shall be comprising of the following accessories

Incomming MCCB 200A - 01 No and out outgoint MCCB 160A -04 Nos with suitable aluminum bus bar arrangement system.

RYB neon indicating lamp set of three- 01

Taking down old Unsv bus bars chamber and Supply and install, testing and commissioning of Bus bar chamber of size 120 cm x 160cm x 60 cm outdoor type suitable for LT 415 volts 3 phase 4 wire system factory made cubical complete materialised dust and vermin proof (protection class IP 54), made out of 3.15mm thick MS sheet (CRCA) including factory made hinged type door both side opening with locking arrangement duly painted with two coats of synthetic enamel paint with powder coated finish over a coat of zinc chrome primer complete all as specified and directed by Engineer-In-Charge. the panel board shall be comprising of the following accessories

Incomming MCCB 600A - 01 No and out outgoint MCCB 250A -04 Nos with suitable 600 amp aluminum bus bar arrangement system.

RYB neon indicating lamp set of three- 01

Taking down old Unsv bus bars chamber and Supply and install, testing and commissioning of Bus bar chamber of size 120 cm x 160cm x 60 cm outdoor type suitable for LT 415 volts 3 phase 4 wire system factory made cubical complete materialised dust and vermin proof (protection class IP 54), made out of 3.15mm thick MS sheet (CRCA) including factory made hinged type door both side opening with locking arrangement duly painted with two coats of synthetic enamel paint with powder coated finish over a coat of zinc chrome primer complete all as specified and directed by Engineer-In-Charge. the panel board shall be comprising of the following accessories

Incomming MCCB 400A - 01 No and out outgoint MCCB 200A -04 Nos with suitable 600 amp aluminum bus bar arrangement system.

RYB neon indicating lamp set of three- 01

Taking down old Unsv bus bars chamber and Supply and install, testing and commissioning of Bus bar chamber of size 90 cm x 90cm x 40 cm outdoor type suitable for LT 415 volts 3 phase 4 wire system factory made cubical complete materialised dust and vermin proof (protection class IP 54), made out of 3.15mm thick MS sheet (CRCA) including factory made hinged type door both side opening with locking arrangement duly painted with two coats of synthetic enamel paint with powder coated finish over a coat of zinc chrome primer complete all as specified and directed by Engineer-In-Charge. the panel board shall be comprising of the following accessories

Incomming MCCB 160A - 01 No with suitable aluminum bus bar arrangement system.

RYB neon indicating lamp set of three- 01

Notes item No 17 to 20 : (i) Rates are deemed to be inclusive of PCC platform of suitable size and 45cm height and 4 Nos legs of 50mmx50mmx6mm and 60 cm in height for fixing the panel (iii) Danger notice plate (02 Nos) LT size 20cmx 15cm shall be fixed on the panel (iv) Contractor should provided power coated finish paint on panel.

Supply & Fixing in repairs 40mm bore mild steel tubing, "light grade" galvanized protection of under ground cable, on poles/walls/under road crossing etc with clamps/all fittings for holding the pipes including cutting and making good distrubed surgace complete all as specidired and directed.

Material and labour painting or old surface and applying two coats of aluminium paint over a coat zinc chrome primer to existing MS channel , clamps, etc on exixting RCC poles of 9/11 mtr all as specified and directed.

Excavating in trenches n. exc 1.5m wide and n. exc 1.5m in depth for foundation/ pipes/ cable etc, n. exc 10sqm on plan and n.exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick, in soil complete all as specified and directed.

Removing of excavated surplus soils, n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

Material & Labour for PCC 1 : 3 : 6 type C-2 using 40mm grade stone aggregate for foundation of stay/ pole/ strut as per specified and directed.

Material & Labour for PCC 1 : 3 : 6 type C-1 using 20mm graded stone aggregate for Coping of above gound level including necessary from work, finishing to exposed surface even and smooth without using extra cement complete all as specified and directed.

Material & labour for sand cushioning for PVC/XLPE cable with screened and washed sand and punning to provided a required covers all as specified and directed.

Material & labour for Double wall corrugated HDPE Pipe, heavey duty for laying of electric cables cross-sectional area 80mm dia complete all as specified & directed.

Material & labour for XLPE insulated, armoured heavey duty electric cables with aliminium concductor, 1100 volts grade cross-sectional area 50 sqmm 3½ core complete with lugs and clamps all as specified & directed.

M/s K R and Sons

KAVYA ENTERPRISES

shri balaji trading corporation