5.00 Lakhs Litres Sump

Amount

2.6.1A Earth work in excavation over areas (exceeding 30cm in depth, 1.5m in width as well as 10sqm on plan) including disposal of excavated earth lead upto 50m and lift upto 1.5m ; disposed earth to be levelled and neatly dresses - all kinds of soil.

2.16.2 Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered)-Depth exceeding 1.5m but not exceeding 3m.

2.25 Filling available excavated earth (excluding rock) in trenches, plinth sides of foundations etc.in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift up the 1.5m.

2.26.1 Extra for every additional lift of 1.5m or part thereof in - All kinds of soil.

2.27 Supplying and filling in plinth with sand under floors including, watering, ramming consolidating and dressing complete.

4.1.9 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:4:8 (1 cement:4 fine sand : 8 graded stone aggregate 40mm nominal size).

5.1.2 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering,shuttering,finishing and reinforcement -All work upto plinth level : 1:1.5:3 (1 cement : 1 .5 coarse sand : 3 graded stone aggregate 20mm nominal size).

5.9.1 Centring and shuttering including strutting, propping etc.and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete.- Using steel sheet with M.S.frames.

5.9.2 Centring and shuttering including strutting, propping etc. and removal of form for: Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.- Using steel sheet with M.S.frames.

5.9.3 Centring and shuttering including strutting, propping etc. and removal of form for: suspended floors, roofs, landings, balconies and access platform- Using steel sheet with M.S.frames.

5.9.5 Centring and shuttering including strutting, propping etc. and removal of form for: lintels, beams, plinth beams, girders, bressumers and cantilevers.- Using steel sheet with M.S.frames

5.9.6 Centring and shuttering including strutting, propping etc. and removal of form for: columns, pillars, piers, abutments, posts and struts.- Using steel sheet with M.S.frames.

5.22.6 Reinforcement for R.C.C work including straightening , cutting , bending , placing in position and binding all complete - Thermo - Mechanically treated bars (TISCON / VIZAG / IISCO /SAIL / JSW) including placing the M30 grade Athees make cover block @ 60cm centre to centre.

13.16.1 6mm cement plaster of mix 1:3 (1 cement: 3 fine sand).

13.1.1 12mm cement plaster of mix Cement Mortor 1:4 (1 cement: 4 fine sand).

13.6.1 20mm cement plaster of mix 1:4 (1 cement: 4 coarse sand).

31.160.1M Providing, laying and jointing UPVC pipes(Finolex/Jain) (1 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,excluding UPVC specials such as bends,tees, threaded pieces, couplers, reducer, endcaps etc.,complete all as per IS and CPWD specification. - 200mm dia.

31.48.1D Providing and fixing C.I sluice valve (PN1) (with cap) conforming to IS 14846 and ISI marked, with bolts, nuts, rubberinsertion etc., complete (the tail pieces if required will be paid separately) - 150 mm dia.

31.130.1A Providing and laying in position flanged C.I. specials such as tees, bends, collors, tapers, caps etc.conforming to IS specification 1538 and ISI marked - 80 to200mm dia.

20.2.2 Boring, providing and installing bored cast-in-situ reinforced cement concrete pile of specified diameter and length below the pile cap M35 in cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with, bentonite solutions and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc., all complete, including removal of excavated earth with all lifts and leads (length of pile for payment shall be measured upto bottom of pile cap). 400mm dia piles.

Basic Code No.1.1.1(a)(ii) Conveyance of surplus excavated earth to Government site within a lead of 3.00 km radius and lift upto 1.50 m including loading, transporting, unloading, levelling etc. complete as directed by the Engineer-In-charge.

31.250.1H Supplying of electrically operated wet type submersible motor and pumpset (Texmo/ KSB/Taro/ Kirloskar make), AC 3 phase, 415 volts, 50 Hz, 2900-3000 RPM. The pump shall have brass impeller, high grade steel shaft with sufficient stages having outlet size of 2"/2.5"/3" dia. to suit the borewell (150 / 200mm dia.), complete. The rate includes all taxes, freight, etc., at site. The pumpset shall be guaranteed for a period of one year from the date of commissioning.(15 HP Submersible motor and pumpset.

2.4.7 Providing and fixing of sheet steel, TP&N switch Rewirable porcelain fuse unit, 415volts including drilling holes on the board, connections, earthing the body etc. as required. 100 Amps Triple pole main switch. Make: Standard/ Havells:-

11.2.1 Laying of one number PVC insualted and PVC sheathed/XLPE power cable of 1.1KV grade of exceeding 25sq.mm but not exceeding 120sq.mm direct in ground including excavation sand, cushioning, protective covering and refilling the trench etc as required in Mud Road.

Basic Code No.3300 Supplying and fixing Providing and fixing 15HP with relay range 14 to23 Fully automatic star delta starters with SPP feature. Make: Siemens/BCH/L&T as directed by the Engineer-in-charge.

Basic Code No.3275A Supply and fixing 6.0 Sqmm , submersible motor 3 core copper flat cable. Make: Havells/ Finolex as directed by the Engineer-in-charge.

Basic Code No.3332 Supplying and fixing Digital voltmeter (0 - 500V). Make: Siemens/Legrand- Lexic as directed by the Engineer-in-charge.

Basic Code No.3334 Supplying and fixing 100/5A current transformer (0.5 % precision. Make: L&T Hager/ Legrand - Lexic as directed by the Engineer-in-charge.

vankayala Narendra

Mattaparthi Ganeswara rao

mvs murthy