Special repair to Main Office Telecom Dark room and certain room Bldge noT 04 at EME WORK SHOP under AGE BR II at GE Faizabad

Amount

Dismantling of plain or corrugated steel sheeting, any guage, thickness, in roofs covrings ,partitons etc., complete all as specified.

Supply & fixing of Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified.

Supply & fixing of 7 Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete all as specified.

Dismantling timber scantlings 40 sq. cm and over in section, in any position etc. , complete all as specified.

S & F rolled mild steel in tubular trusses/purlins etc including special shaped washers etc complte using ERW or induction butt welded tubes conforming to Fe 410Gde E-250) , complete all as specified.

Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc conforming to Fe 410Gde E-250) , complete all as specified.

Dismantling false ceiling of any description including any type of frame , complete all as specified.

M&L for E- board tiles ceiling on GI powder coated channel/ Tee/ Grid of make(Armstrong) or equivalent as approved by GE , frame work with the following specification including cutting holes in brick wall built in cement mortar & making good in cement concrete 1:2:4 type B-0/ cement mortar 1:3 complete all as secified and directed with following:-(1) M&L plugging to wall around the rooms & supplying & fixing GI powder coated angle of size 25mmx25mm. (2) S&F of 1.60mm dia GI wire suspenders with adjustable clamps including fixing to ceiling to dash free fasteners. (3) S&F GI powder coated tee as in m,ain & cross members at 595mm centre to centre supported suspenders along with adjustable camp to maintain level (4) S&F E-board (Make- Everest Industries Limited or equivalent as approved by GE) ceiling tiles of size 595mmx 595mm and 4-5mm thickness, confirming to relevant IS in square of GI powder coated tee with clips made to shape , shae and pattern of PVC board shall be as approved by GE, complete all as specified.

Taking down cement plaster on brick or stone walls, etc. including racking out joint, haccking for key, scrubbing with water, etc. , complete all as specified.

M&L for rendering 15mm in two layer on fair faces of brick work or concrete surfaces in CM (1:4) with liquied water proofing compound as per manufacture instruction and finished the surface even and smooth (without using extra lime or cement ) . , complete all as specified.Note ;-WPC Shall be paid seperately.

M&L for rendering 15mm on other than fair faces of brick work or concrete surfaces in CM (1:6) and finished the surface even and smooth (without using extra cement ) , complete all as specified.

M&L for preparing new plastered surfaces of wall and applying two coats of cement base paint , complete all as specified.

M&L for preparing old plastered surfaces of wall and applying two coats of cement base paint , complete all as specified.

M&L for preparing of new plastered surfaces of walls and applying two coat of oil bond distemper over one coat of primer , complete all as specified.

M&L for preparing of old plastered surfaces of walls and Complete removal of existing treatment applying two coat of oil bond disterper over one coat of primer , complete all as specified.

Supply only liquid water proofing compound ISI Marked , complete all as specified .

M&L for preparation of new steel surfaces of any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel including one coat of red oxide primer complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles to store and rubbish off the premises.

Material & labour for non skid ceramic coloured tiles 7mm to 8mm thick (Square/rectangular) area of each tile exc 0.11sqm but n.exc 0.18sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement , complete all as specified.

Material & labour for non skid ceramic coloured tiles 7mm to 8mm thick (Square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18sqm coloured in skirting/dado etc set and jointed in neat cement slurry and pointed in white or coloured cement , complete all as specified.

M&L for glazed ceremic coloured tiled in vertical surfaces 350x250x7mm /450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match a , complete all as specified.

M&L screed bed or bedding layer of CM (1:6) 15mm thick for laying floor finises of tiles , complete all as specified.

M&L for rendering 10mm thick in CM 1:4 on verticle surfaces of wall for fixing of wall tiles , complete all as specified.

Demolition of brick work built in cement mortar incl all quoins, arches pillars etc but excluding ashlar facings etc. , complete all as specified.

M&L for brick work with sub class brick B brick on straight on curved on plan to exc 6 m mean radious in CM (1:6) complete all as specified , complete all as specified.

M & L for PCC 1 : 2 : 4 Type B-0 ( 12.5 mm graded crushed stone aggregate) steps,seismic and other similiar bands, plinth courses,string courses, laacing courses parapets and railings upto 60 cm in height, bed plates, copings, kerbs, etc. water troughs and the like includind weathering, slightly rounded or chamfered angles and throating , complete all as specified.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C-2 using 40 mm graded crushed stone aggregate as in sub-base of floors, plinth protection finished the surface of concrete fair and even , complete all as specified.

S& F in repairs fancy type curtain rods metal polished 25 mm dia with end fittings and fixing brackets of required size ( two nos end brackets and two Nos wall brackets fixed with wooden gutties and screws. , complete all as specified.

S&F anodised aluminium sections in any of door, windows and ventilator etc including fabricator of frame shutter and fixing with necessary glazing clips, joining cleats etc., complete all as specified .

S & F anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified .

S & F for Anodised aluminium window and ventilator shutters, side hung typewithout sash bars, aluminium section sweighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). Hinges type B-21100mm long (2 no.) suitable handle (2 no.) complete all as specified.

M&L for Mild steel framed work such as Iron door , grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladders; framed balusters, railing;frame work for water tanks and similar work conforming to Fe 290.Gde-E-165, , complete all as specified .

Supply Heat absorbing glass, 5mm thick and glazing complete with beads fixed with brass screws , complete all as specified.

Supply only Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aoerture of 1.40 mm fixed with stainless steel staples , complete all as specified.

S&F double action floor door spring hydraulically regulated made of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover,govering pivot made of mild steel heavy duty suitable for Aluminium door , complete all as specified.

M & L for black granite(of any type)stone slab 18 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with rounding to edges of stone slabs one edg complete Including 10mm thick backing coat CM 1:4 , complete all as specified.

Taking down chowkhats or frame (with shuuter w/o taking of shutter from frame exc 1.5 sqmtr but n.exc 4 sq m each.) complete all as specified.

S & F pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete of size 125 X 60 mm complete all as specified.

M&L preparing of surface of wood and based material steel and iron work new ,of any description and girth , not otherwise described and treated with tar or coil tar black paint treated ends of posts, backs of chowkats etc area exc 0.10 sqm but n. exc 0.5 sqm each.

M & L for PCC 1 : 2 : 4 Type B-0 ( 12.5 mm graded crushed stone aggregate) in filling under pressed steel door frame,lintel upto 1.5m clear span,cill, steps,seismic and other similiar bands, plinth courses,string courses, laacing courses parapets and railings upto 60 cm in height, bed plates, copings, kerbs, etc. water troughs and the like includind weathering, slightly rounded or chamfered angles and throating , complete all as specified.

S & F 35 mm thick 2nd class HW rail and styl Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated , complete all as specified.

S&F Aluminium anodised barrel tower bolts 200 mm of extruded section and fixed , complete all as specified.

S&F 150 mm long extruded aluminium alloy handles, fabricated type,anodised , complete all as specified .

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed , complete all as specified.

S& F 140 mm floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring, fixed in floor ,complete all as specified .

Demolition of cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified .

M & L for 100 mm thick, plain cement concrete type C-2, 1:4:8 using 40 mm graded crushed stone aggregate, finished even & rough, as in sub base, , complete all as specified.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand , complete all as specified.

Taking down carefully aluminium point wiring 1.5 Sq mm of complete,switch socket 5amps & power point etc including switches and making good distured surfaces of walls / ceiling etc all as specified.

M & L point wiring for one light point/fan point controlled by one, one way switch using 1.5 Sqmm nominal cross sectional area multistranded copper conductor,FR PVC insulated unsheathed cable in and including 20 mm dia or higer size PVC concealed conduit and fittings with 1.5 Sqmm nominal cross sectional area used as continuous earth wire and connected to earth dolly including metal flush boxes with white cover plate and making neccessory electrical connection of modular type Switches, sockets,regulators etc , complete all as specified for One light point or fan point controlled by one switch

All as per item no. 50 but One 3 pin socket outlet 5 amps on same board with other switches

All as per item no. 50 but One 3 pin socket outlet 5 amps on ind board with other switches

M & L for point wiring with 2.5 Sqmm (nominal cross-sectional area) FR PVC insulated & unsheathed 1100 volts grade multi stranded copper conductor single core cable drawn through and including non-metallic rigid PVC conduit/PVC casing caping of adequate size with all fittings and accessories including PVC sunk box with 3mm thick plastic laminated sheet top cover complete including FR PVC insulated & unsheathed single core multistranded copper conductor cable of size 1.5 Sqmm green in colour as earth continuity conductor connected to common earth dolly for one 16 Amp socket outlet on independent board, complete all as specified.

All as per item no. 53 but on same board

S & F switch piano flush type one way 6 Amps , complete all as specified.

S&F switch piano, flush type, one way, 16 Amps , complete all as specified.

S & F socket outlet 5 pin, 6 Amp flush type, complete all as specified.

S&F socket 2 in 1, 3 pin, 5 and 16 Amps flush type , complete all as specified.

S & F ceiling rose surface bakelite three terminals , complete all as specified.

S & F stepped type electronic fan regulator flush type , complete all as specified.

M & L for Sub main wiring complete with two run of 4 sqmm ( nomoal area) single core ( Using colour code for phase & Neutral and one run of 2.5 sqmm ( nominal area) single core Green in colour as earth continuity conductor to common earth dollyPVC insulated multistranded copper conductor 1100 volts FR grade drawn through PVC casing & caping including taking down the existing submain wiring complete all as specified and directed. Note :Two runs of 4 sqmm ,one run of 2.5 sqmm size& one run of casing caping cable shall be measured as one length .

M & L for Sub main wiring complete with two run of 6 sqmm ( nomoal area) single core ( Using colour code for phase & Neutral and one run of 4 sqmm ( nominal area) single core Green in colour as earth continuity conductor to common earth dollyPVC insulated multistranded copper conductor 1100 volts FR grade drawn through PVC casing & caping including taking down the existing submain wiring complete all as specified and directed.Note:Two runs of 6 sqmm ,one run of 4 sqmm size& one run of casing caping cable shall be measured as one length .

M & L for Sub main wiring complete with four run of 10 sqmm ( nominal area) single core ( Using colour code for phase & Neutral and two run of 6 sqmm ( nominal area) single core Green in colour as earth continuity conductor to common earth dolly PVC insulated multistranded copper conductor 1100 volts FR grade drawn through PVC casing & caping including taking down the existing submain wiring complete all as specified and directed. Note . :- Four runs of 10 sqmm ,Two run of 6 sqmm size & one run of casing caping cable shall be measured as one length

M & L for Sub main wiring complete with four run of 6 sqmm ( nominal area) single core ( Using colour code for phase & Neutral and two run of 4 sqmm ( nominal area) single core Green in colour as earth continuity conductor to common earth dolly PVC insulated multistranded copper conductor 1100 volts FR grade drawn through PVC casing & caping including taking down the existing submain wiring complete all as specified and directed. Note :- Four runs of 6 sqmm ,Two run of 4 sqmm size & one run of casing caping cable shall be measured as one length

Taking down unserviceable main switch, DB’s insulators, DB for MCB and board etc. of any type and any capacity and further disposal including making good the disturbed surface and matching the colour of wall with the existing colour wash/ paint/ distemper wherever required complete all as specified and as directed.

Supply and fix epoxy powder coated MCB distribution box double door TPN 4 way vertical type for MCBs alonwith provn of MCCB as incomer with common bus-bar at incoming end of outgoing MCBs grouted/ flush to wall complete all as specified. [Note: - MCCB and MCBs will be measured and paid under separate item]

S&F (Thermal Magnetic) Release MCCB 100 A , TPN Adjustable Overload 80-100% Adjustable Short Circuit 5-10 In and breaking capacity 25 kA.

S&F epoxy powder coated MCB, DB, double door TPN horizontal 4 way for MCBs with common bus-bar at incoming end of outgoing MCBs grouted/ flush to wall all as directed.

S&F MCB, 4 pole, 63 A, 16 kA, 'C' curve

S&F MCB, 4 pole, 32 A, 16 kA, 'C' curve

S&F epoxy powder coated MCB, DB, double door SPN 8 way for MCBs with common bus-bar at incoming end of outgoing MCBs grouted/ flush to wall all as directed.

S&F epoxy powder coated MCB, DB, double door SPN 4 way for MCBs with common bus-bar at incoming end of outgoing MCBs grouted/ flush to wall all as directed.

M & L MCB SPN 32 Amps ' C' series , 240 volts.

M & L MCB SP- Amps " C" Series ,240 volts.

Supply and fixing Distribution Box 32A, 5P, 415V including Socket & Plug complete all as specified and directed.

S&F LED tube light fitting,1X18 Watt surface and wall mounted decorative ultra slim square profile with extruded polycarbonate, environmental friendly, energy efficient ready to use paclk fitting including provn of twin core multi stranded copper cable of size 1.5 Sqmm from ceiling rose to tube light fitting complete all as specified and directed.

S & F in repair lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as speicfied.

S&F 1 x 36 W LED fitting 2'X2' suitable for ceiling mounting, Environmental friendly, new generation,aesthetically designed, ultra modern luminaire with high brightness SMD LEDs as light source including all fixing accessories complete all as specified and directed.

Supply and fixing bldg security light LED 15 Watt , IP 66, including provisioning of Siutable size of GI bracket , clamp and nut and bolt etc including PVC insulated twested wire 3 core 23/0076 cooper conductor flexible PVC insulated wire complete all as specified and directed.

Supply and fixing heavy duty exhaust fans 450 mm sweep , 230 volts complete with all connected accessories ie fixing nut , bolt , washers , louvers shutter etc. including making of suitable size hole on the wall and PVC insulated twested wire 3 core 23/0076 cooper conductor flexible PVC insulated wire complete all as specified and directed.

Supply and fixing Wall mounted fan 400 mm including PVC insulated twested wire 3 core 23/0076 cooper conductor flexible PVC insulated wire complete all as specified and directed.

M&L earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in to ground (earth pit) not less than 2.25 meters deep below GL with top edge of earth plate not less than 1.50 m below ground level, connected to GI lead wire of 4 mm dia. (7.50 m long) by means of nuts, bolts and washers, check nuts of GI and protected by the GI pipe light grade 1.5 mm nominal bore (7.50 m Long) for earth plead wire, watering pipe light grade of 20 mm nominal bore, 0.63 mm thick CI funnel, wire mesh etc complete including necessary earth work and excavation in any type of soil, PCC 1:2:4 type B1 earth pit and Precast RCC cover 50 mm thick dully reinforced with 6 mm dia, MS round bars @ 100 mm C/C both ways, earth testing point, making good to floor complete all as specified.

Taking down old unserviceable service connection/UG cable of size.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core.

Excavation in trenches, not exceeding 1.5 meter wide and not exceeding 1.5 meter in depth for foundation of poles, stays or for taking out/laying of cables and getting out in soft/loose soil complete all as specified and directed by Engr-in-Charge.

Removing excavated materials (soil) n. exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed by Engr-in-Charge.

M & L for sand cushioning to underground cable with clean dry river sand complete all as specified and directed by Engr-in-Charge. Note:- Punned thickness only shall be measured & Paid.

Supply & Laying of sub class 'B'bricks locally available best quality laid flat (length of bricks laid across the length of cable) in tranches for protection of U/G cable complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in soft/loose soil complete all as specified and directed by Engr-in-Charge.

K R KAUSHAL AND SONS

R.S Enterprises

His And Her Enterprises

ABC CONSTRUCTION CO

MISRA TRADING CORPORATION

Saket Traders

Khan Brothers