PROVN OF SHELTER BUILDING FOR DG SETS AT AF STN THOISE

Amount

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in hard and dense soil concrete all as specified and directed.

Excavating in trenches in hard dense soil n.exc 1.5m wide and n.exc 1.5m in depth for foundation, laying pipes, cables etc n.exc 10Sqm on plan and n.exc 1.5m in depth and getting out in hard dense soil concrete all as specified and directed.

M&L for cement concrete type D2 1:4:8 (40mm graded aggregate) in foundation, filling and mass concrete all as specified and directed.

M & L for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection, finished even and fair without using extra cement, complete all as directed.

M&L for RCC Nominal mix type B-0 1:2:4 (12.5 mm graded crushed stone agg) as in foundation, indl raft, footing foundation beams, plinth beams bases for columns, etc basement slab, under ramed piles and mass concrete all as specified and directed.

M&L for RCC Nominal mix type B-0 1:2:4 (12.5 mm graded crushed stone agg) as in Beams, cantilevers, bressummers,lintels over 1.5m span all as specified and directed.

M&L for RCC Nominal mix type B-0 1:2:4 (12.5 mm graded crushed stone agg) as in Columns, pillars, piers, posts all as specified and directed.

Form work to sides of concrete foundations, footings, bases of columns, sides and soffits of foundation and plinth beams and similar work vertical or batter all as specified and directed.

Form work to sides of pillars, posts and columns all as specified and directed.

M&L for steel reinf TMT bars 10 mm dia and over cut to length and bent to shape required including cranking, bending spirally for hoping for columns, hooking end and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

.-ditto- but 5mm dia and over upto and including 10mm dia as in stirrups spacer and binders complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry with solid blocks, Type C1 1:3:6 (using 20 mm graded aggregate) exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for rendering 10mm thick in CM (1:6) on brick masonry/ precast cement concrete block masonry internal surfaces of walls finished even and smooth without using extra cement complete all as specified and directed by Engr in Charge.

M/L 15 mm thick rendering CM 1:4 of brick masonry/ precast cement concrete block masonry surfaces and finished even and smooth without using extra cement all as specified.

M & L three coats of white wash on new plastered surfaces on wall including preparation of new plastered surfaces all as specified and as directed .

M&L two coats of Cement Base Paint over a coat of alkali resistant primer on newly plastered surfaces of walls (camouflage pattern) including preperation of new surfaces all as specified and as directed.

S&F 0.63 mm thick Galvanised, corrugated mild steel shetting with two corrugations side lap, fixed with coach screws, washers, and L-type or J-type or cranked hook bolts in lieu of screw in roofs, walls etc. With grade of zinc coating 275 etc all as specifed.

S&F 0.63 mm thick plain Galvanised, mild steel shetting in ridges, hips, vally gutters, drip, straight flashing & fixed with coach screws, washers, and L-type or J-type or cranked hook bolts in lieu of screw in roofs, walls etc. (length and girth as fixed) with grade of zinc coating 275 etc all as specifed.

M&L for preparation of new steel surfaces applying two coat synthetic enamel paint over a coat of red oxide (camouflage pattern) etc all as specified and directed by Engr-in-Charge.

S&F of Roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conferming to Fe 410W (gde -E-250) quality A all as specified and as directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut 22.5cm and n exc 30cm long all as specified and as directed.

S&F Mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conferming to Fe 410W (gde -E-250) all as specified and as directed.

S&F Steel rolling shutters, with out ball bearing, but gear operated type with bevel gear box and crank handle as specified including top cover, an choring rod, hasp and staple and one shop coat of primer erected in position as indicated complete thickness of lathe in 1.00 mm all as specified and as directed.

M & L Synthetic enamel paint two coats on over 10cm width or girth of steel surfaces (camouflage pattern) complete all as specified and directed by Engr in charge

M & L Synthetic enamel paint two coats on new steel surface any description over 10cm width or girth over a coat of red oxide primer including preparation of surfaces complete all as specified and directed by Engr in charge

M&L for Hard core, broken stone or boulders of gauge n exc 63, deposit spread and levelled in layers n exc 15 mm thick watered and ramed to a true surface all as specified and as directed.

M&L for Cement concrete 1:4:8 type D2(using 40 mm graded stone aggregate) 100 mm thick as in sub base all as specified and as directed.

M&L for Cement concrete 1:2:4 type B1(using 20 mm graded stone aggregate) 100 mm thick as in flooring all as specified and as directed.

S&F Gl frame work for snapgrid false ceiling comprising of Gl perimeter channnel 0.55 mm thick with Main T- flange of 25 mm and web of 30 mm fixed to surrounding wall angle with flange and web 25 mm each , Cross T with flange 25 mm and web 25 mm fixed to main T, Main T is suspended from soffit @ 1200 mmm c/c using GI wire of 2mm thickness GI frame will be 60 x 60 cm to recieve E-board ceiling complete all as specified and as directed all as specified and as directed.

M&L 4mm thick E Board 600x600 mm prepainted fibre boards ceiling designer/decorative type with different designs as approved by the Engr-in-charge fixed or laid in ceiling timber /GI/ aluminium frame work in ceiling flat or sloping complete all as per manufacturer instructionall as specified and as directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as specified and as directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty/ wooden beading in square n. exc. 0.5 Sqm in each pane, Complete all as specified and as directed by Engr in Charge.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness M-40 grade with grey cment and pigment complete all as specified and directed

M&L for sand cushning/ sand filling under floor in 25 mm thick (bleow paver blocks) in including watering and consolidation complete all as specified and directed

M & L for screed bed or bedding layer of 20 mm thick for laying floors finishes in CM 1:6 etc all as specified.

M/L Non skid ceramic coloured tiles 7 to 8 mm thick , area of each tile exc. 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr in Charge.

M & L for rendering 10 mm thick in CM 1:4 on concrete surfaces as in backing coat for dado complete all as specified and directed by Engr in Charge.

M & L for glazed coloured ceramic tiles in vertical surface 300x 450x 7 mm thick set and jointed in neat cement slurry and pointed in colour cement to match complete all as specified and directed by Engr in Charge.

M/L 5 mm thick rendering in cement mortar (1:3) on ceiling and finished even and smooth without using extra cement all as specified.

M & L two coats of white wash on new plastered surfaces on ceiling including preparation of new plastered surfaces all as specified and as directed .

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engr in Charge.

Formwork to edges of concrete fair finish surface exc. 10 cm but n. exc. 20 cm wide (Horizontal or sloping) complete all as specified and directed by Engr in Charge.

M&L for cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams etc complete all as specified and directed

S&F Anodised aluminium ventilator louvers with frames, without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. and including all necessary fittings complete all as specified and directed

S&F 4.8 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

supplied and fixed Pressed steel frames for doors (105x60mm) with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified.

M&L for 35mm 2nd class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed

S&F 150mm long aluminium handles, cast type, anodised complete all as specified and directed complete all as specified and directed by Engr in Charge.

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed

M&L for preparation of new untreated surface and applying two coats of synthetic enamel paint over a coat of pink primer on wood surface complete all as specified and directed.

S & F vitreous china wash basin white ,flat,flate back size 550 x 400 mm excluding taps,waste pipe,chain and plug and procelain stopper but including brackets.

S&F 15 mm bore dia Pillar taps, cast copper alloy, fancy type, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F bib taps cast copper alloy ISI marked with crutch or butter fly handles fancy type chromium plated screwed down screwed for iron pipe of 15mm bore all as spd and directed.

S&F Stop valve/ Angle valve cast copper alloy (ISI Marked) chromium plated screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia, complete all as specified and directed.

S&F Vitreous China squatting pan of orissa pattern, size 580x440mm white with CI ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern ( including fixing of flush pipe) including provision of cement concrete bedding, in repair complete all as specified and as directed.

S&F PVC flushing cistern 10 ltr capacity incl PVC connection inlet and and outlet connections,brackets, PVC flush pipe with bend 32 mm dia of suitable length including making necessary connections to water supply pipe line and jointing to WC all as specified and directed.

S&F Vitreous china bowl urinal flat back, size of 465 x 355 x265 mm white (minimum ),with grating and union for discharge pipe (excluding flushing cistern and flush pipe and waste pipe )complete including provding and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F 15 mm bore Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engr in Charge.

S&F 20 mm bore Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engr in Charge.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; andcutting chases for concealed watertubing or concealed conduit wiring,etc., and making good, cutting notexc 10 cm girth complete all as specified and directed by Engr in Charge.

S & F stop valves suitable for 20 mm bore iron pipe, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed by Engr in Charge.

S&F PVC (SWR) floor trap 75 mm with grating including jointing to waste pipe with solvent cement fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr in Charge.

S&F PVC (SWR) gully trap 125/110 mm with grating including jointing to waste pipe with solvent cement and fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr in Charge.

M&L 110 mm dia PVC (SWR) type "B' pipes single socketed in any length with rubber ring joints, laid in trenches or floors as waste pipes jointed with solvent cement complete all as specified and directed by Engr in Charge.

M&L 75 mm dia PVC (SWR) type "B' pipes single socketed in any length with rubber ring joints, laid in trenches or floors as waste pipes jointed with solvent cement complete all as specified and directed by Engr in Charge.

M&L 110 mm dia PVC (SWR) Bends for connecting or diversion of pipes fixed with solvent cemnt complete all as specified and directed by Engr in Charge.

M&L 75 mm dia PVC (SWR) Bends for connecting or diversion of pipes fixed with solvent cemnt complete all as specified and directed by Engr in Charge.

M&L 150 mm dia PVC (SWR) type "B' pipes single socketed in any length with rubber ring joints, laid in trenches or floors as waste pipes jointed with solvent cement incl demolition of existing complete all as specified and directed by Engr in Charge.

M&L for cement Concrete bed (1:4:8 type D2) to 150 mm dia pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

S&F 500 ltrs Puff insulated PVC water storage tanks (Cylindrical verical with closed top) for continous temperature control, Hight quality LLDPE material bonded with RP,insulated models polyurethane foam in middle layer, 100% leak proof etc fixed in position, omplete all as specified and directed

M&L for PCC 1:2:4, type B1 using 20 mm graded stone aggregate in coping & in bedding & haunching against the side of wall of manholes complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregates) as in landings, cover slab (for manholes), shelves & similar articles with plan faces & set in CM 1:4 complete all as specified and directed.

Returning, filling including spreading, watering and well ramming in layers n.exc 25 CM in foft/loose and hard/dense soil all as specified and as directed.

Removing excavated material to a distance exc 250 mtr but not exc 500 mtr depositing where directed all as specified and as directed.

M & L for Point wiring for one light point/ fan point/ Bell point controlled by one switch with 1.5 sqmm PVC insulated and unsheathed FR-LSH copper conductor single core multi stranded flexible copper cable 1100 Volts grade conforming to IS-1990 using approved colour code as per IS code drawn through non metallic rigid PVC casing Caping heavy duty double locked with size as per site requirement in accordance with clause No 19.25 of SSR Part I) ISI marked including casing caping accessories like bends, tees, junction boxes etc fixed with all accessories complete with MS boox of sheet made of 1.600mm thick as indicated and shall conform to IS-14772-2000 with 3 mm thick hylam sheet for fixing of switch, socket regualtor etc along with PVC insulated and unsheathed FR-LSH 1.5 sqmm multi stranded copper conductor cable 1100V (green color) as continuous earth lead wire connected to common earth and earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per Ser item No 78 here-in-before but for 06 Amp socket outlets point controlled by one switch on Independent board with the cable 1.50 sqmm size complete all as specified and directed.

All as per Ser item No 78 here-in-before but for 06 Amp socket outlets point controlled by one switch on same board with the cable 1.50 sqmm size complete all as specified and directed.

All as per ser item No 78 here-in-before but for 16 Amp socket outlets point controlled by one switch on Independent socket outlet using 2.5sqmm PVC insulated and unsheathed FR-LSH copper conductor single core multi stranded flexible copper cable 1100V of approved colour code as per IS code for phase and neutral along with PVC insulated and unsheathed FR-LSH 2.5 sqmm multi stranded copper unsheathed cable 1100V (green color) as continuous earth lead wire connected to common earth and earth dolly complete all as specified and directed.

M&L Switch piano, flush type, single pole, one way, 5 Amps, complete all as specified and as directed by Engineer-In-Charge.

M&LSwitch socket combination, 2-in-1, 3-pin, 5-Amps, flush type, complete all as specified and as directed by Engineer-In-Charge.

M&L Switch socket combination 2-in-1, 3-pin, 5 and 15 Amp flush type universal type, complete all as specified and as directed by Engineer-In-Charge.

Supply and fixing Lamp holder, white Polycarbonate body, with back plate suitable for batten fittings fixed in position & connecting complete all as specified and as directed.

S&F LED light fitting mirror type with high ouput diffuser 2 feet ,10 watt 220 volts AC decorative type energy efficient LED integrated batten type luminaires suitable for wall or ceiling mounting with built in LED Chip & integral LED driver 10 watt,Aluminium channel housing & Polycarbonate diffuser ,Color temperature 6500 K or as directed,Luminaire efficacy not less 100 lm/W with all accessories, fixing arrangement internally pre-wired, making all connection using 1.5 sqmm copper conductor multistarnd PVC insulated 3 core flexible cable from ceiling rose to fitting drawn through PVC flexible conduit complete fixed in position & connecting complete all as specified and directed by Engr–in-charge.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450m sweep heavy duty with, blades, and frame and louvers, shutter,RPM 1200,copper wiring of motor and all as specified and directed by Engr–in-charge.

S&F LED Street Light fitting 35 watt, for opearting voltage between 110V to 320V system efficiency not less than 120 lumen / watt, PF-0.95 minimum, IP66 protection, 5700CCT(K), CRI between 80-85, confirming to LM79 and LM 80 standards or as per IS-16104:2012 and IS-16106:2012, for estimated life span of minimum 50,000 hrs consisting of high / low voltage cut off, maintenance free isolated Electronic driver circuits, Low THD, PMMA grade high quality Transmittance lens, Epoxy powder coated Die Cast Aluminium housing with LED street optics LENS for uniform light distribution, weather proof gasket for lamp & driver compartment, Heat resistance toughened UV stabilized glass fitted in cast aluminium housing with SS screws, complete all as specified and as directed by Engr-in-charge.

Supply & Fixing Bracket made out of GI light grade pipe of size 40 mm dia 1.5 mtr long bend to an angle of 120 degree with 02 Nos MS clamp 50mm x 50mm and 04 sets of nuts,bolts and washers painting with two coats of synthetic enamel paint over a red oxide primer complete all as specified and as directed by Engr-in-charge.

Sheet metal enclosure MCB distribution board made of special grade CRCA sheet not less than 1.12 mm thick powder coated single pole & neutral 240 volts 8 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases cutting in wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Note - MCBs will be measured separately and shall be of same make as MCBs/Isoleters.

Supply and fixing MCB Single Pole 6 to 32 Amps rating 240V, 10KA 'B' curve miniature circuit breaker complete with connection testing and commissioning complete all as specified.

Supply and fixing 240V, 10 KA curve miniature circuit breaker (MCB) of single poles and neutral and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissionincomplete all as specified and directed.

Excavation in trenches n.exc. 1.5 mtr wide and n.exc 1.5 mtr deep for foundations of poles/stays/cable etc not exc 10 Sqm area on plan and getting out in Hard/Dense soil complete all as specifed and as directed by Engineer-in-Charge.

Returning filling in including spreading levelling, watering and well ramming in layer each not exc. 25 cm thick in a Hard/Dense soil complete all as specified and directed by Enginer-in-Charge.

Removing surplus soil to a distance not exc. 50 mtr and depositing where directed at a level n.exc. 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

M&L for PCC cable cover Class LV, Type I, flat, size 250 mm x 150mm x 40mm laid Flat in trenches over the cable with length 250mm perpendicular to the direction of cable, adjacent/ abutting each other complete all as specified and directed. Note:-Excavation and earth work to be measured and paid for separately

Sand cushioning to protection of underground cables, laid 8 Cm before laying and 15 Cm after laying of cable, and punned to form an overall layer of 18 Cm thick, complete all as specified and directed by Engineer-In-Charge. Note: Punned thickness of sand shall be measured and paid.

M&L XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 Volts grade, cross-sectional area 16.0 Sqmm, 2-core, laid in trenches or passing through pipes, including suitable lugs and accessories for making connections at both ends, complete all as specified and as directed.

Earthing complete with GI earth plate 60×60cm ×6mm thick electrode and 4 mm GI as earthing lead, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion.

Excavation in trenches n.exc. 1.5 mtr wide and n.exc 1.5 mtr deep for foundations of poles/stays/cable etc not exc 10 Sqm area on plan and getting out in Hard/Dense soil complete all as specifed and as directed by Engineer-in-Charge.

Returning filling in including spreading levelling, watering and well ramming in layer each not exc. 25 cm thick in a Hard Dense soil complete all as specified and directed by Enginer-in-Charge.

Removing surplus soil to a distance not exc. 50 mtr and depositing where directed at a level n.exc. 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

M&L of PP-R (Polypropylene random copolymer) pipes, outer dia32 mm, SDR 7.4 (PN-16) , 3-layer, and UV stabilized and anti-microbial fusion welded having thermal stability for hot and cold water supply including all PP-R plain and brass threaded polypropylene random fittings fixed complete to fittings laid in trenches/on ground complete all as specified and as directed by Engineer-In-Charge. Make: SFMC/Finolex/Swami Plast/ Relicance PP-R .

Supply and fix PPR Gate Valves (brass Insert) of 32MM bore

Drilling and tapping GI/PPR water mains (in position) the existing pipe of 32mm t0 75 mm for branch connections including inserting tee of size50x50x25mm or as per site conditions complete all as directed by Engr in charge. Note Excavation , returning filling are deemed to be be included in item rate

M/S SHAMSHER ALI SUFI (BID ID -3118867)

MEHDI ALI (BID ID -3118404)

MS SHOWKAT ALIJOO (BID ID -3118418)

M/S MOHD MUSSA (BID ID -3118431)