CERTAIN REPAIR MAINT WORKS OF SUB AREA STN HQ DSOI 21 CDU SULTANIA RETREAT BTSI SCAPS HQ CEBZ HQ CWE AGE SI LINES ASCONE NODE NCC GROUP HQ AND SARVA DHARM STHAL AT SI LINES UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Taking down chowkats or frames exc 1.50 Sqm but n.exc 4 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frames n exc 1.50 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutters of any descripition exc 1Sqm and n. exc 2 Sqm each complete all as specified and directed.

Easing of door shutters for easy closing / opening tightening of hinges or changing the position of hinges adjustment of tower bolts, sliding bolts with new screws etc complete all as specified and directed.

Easing of window shutters, kitchen cupboard shutters, show case shutter drawers including fixing of screws adjusting handles, knobs tightening piano hinges including misc small adjustments complete all as specified and directed.

Taking down shutters of any description and refixing in the same opening exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections complete all as specified and directed.

S&F of 15 mm bore GI tubing medium grade, galvanised with all fitting and fixed to walls and ceilings or laid in floors complete all as specified and directed.

Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings in trenches complete all as specified and directed.

S&F of 20 mm bore GI tubing medium grade, galvanised with all fitting and fixed to walls and ceilings or laid in floors complete all as specified and directed.

Cutting chases, pinning in and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and directed.

Demolition of brick work or stone masonery built in cement mortar complete all as specified and directed.

M&L for fly ash brick work, straight or curved on plan of any radius in half brick thick walls using modular bricks built in CM 1:4 complete all as specified and directed.

M&L for fly ash brick work, straight or curved on plan exc 6m mean radius using modular bricks built in CM 1:6 complete all as specified and directed.

Demolition of concrete in ground floors and pavings (unreinforced) n.exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) in cills, ceismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

M&L for machine cut kota stone slab 20-25mm thick in dados, skirting and similar work over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) in plinth protection, finished even and smooth without using extra cement including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with bitumen and sand 1:3 by weight complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in sub base for floors and paving complete all as specified and directed.

M&L for 15mm thick screed bed or beding layer of cement mortar 1:6 for laying floor finish, finished even and rough complete all as specifed and directed.

M&L for rendering 10mm thick on brick work or concrete surface in CM 1:4 as back coat to wall tiles, finished even and rough complete all as specified and directed.

M&L for vitrified ceramic light shade tiles 8 to 10mm thick (square/rectangular) polished, of any shade area of each tiles exc 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for vitrified ceramic light shade tiles 8 to 10mm thick (square/rectangular) polished, area of each tiles exc 0.18 Sqm but not exceeding 0.36 Sqm as on vertical surfaces such as skirting, risers to steps, etc; set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for vitrified ceramic light shade tiles 10mm thick (square/rectangular) double charged polished, area of each tiles exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for vitrified light shade tiles 10mm thick (Square/rectangular) double charged polished, area of each tile exceeding 0.36 Sqm, as in vertical surfaces such as skirting, risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7 to 8mm thick (Square/Rectangular) area of each tile exe 0.11 Sqm but not exe 0.18 Sqm in floors etc. set and jointed in cement slurry and pointed with white or coloured cement to match complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7 to 8mm thick (Square/Rectangular) area of each tile exe 0.11 Sqm but not exe 0.18 Sqm in dados, skirting etc; set and jointed in cement slurry and pointed with white or coloured cement to match complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surfaces of size 450x350x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement to match complete all as specified and directed.

M&L for marble work 18-20 mm thick (makrana white) (table rubbed and polished/moulding) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing with white cement (1:2) using marble dust with admixture of pigment to mactch with shade complete all as specified and directed.

M&L for granite stone work 18-20 mm thick (of any type/colour) (table rubbed, polished and edges moulded) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing with white cement (1:2) using marble dust with admixture of pigment to mactch with shade or granite complete all as specified and directed.

M&L for endura joint free coloured tiles 10mm thick (square/rectangular) area of each tiles exc 0.18 sqm but not exceeding 0.36 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles complete all as specified and directed. Make: Johnson endura or equivalent as approved by GE.

M&L for endura joint free coloured tiles 10 mm thick (square/rectangular) area of each tiles not exceeding 0.11 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles complete all as specified and directed. Make: Johnson endura or equivalent as approved by GE.

S&F in repairs 12mm thick laminated wooden flooring including polishing all as per manufacturer instructons including taking old flooring complete all as specified and directed. Make: Action Tesa/ Century as approved by GE.

S&F of powder coated aluminium frames for doors, windows, ventilators with one or more rebates including joining cleat, channel etc for fixing etc. complete all as specified and directed.

Hacking out old broken glass (any thickness quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

S&F of 3mm thick plain sheet glass ordinary quality n.exc 0.50 Sqm in each pane and glazing with oil putty complete all as specified and directed.

S&F of 4.0mm thick plain sheet glass ordinary quality n.exc 0.50 Sqm in each pane and glazing with oil putty complete all as specified and directed.

S&F of 4.0mm thick plain sheet glass ordinary quality exc 0.50 Sqm in each pane and glazing with oil putty complete all as specified and directed.

S&F in repairs 12mm thick toughned glass in door, partitions etc similar work etc with stainless steel handle in approved shape and design complete all as specified and directed.

S&F of solar control film 25 micron reflective type sticked to glass panes as per manufacturer instructions complete all as specified and directed.

S&F of 105x60 mm pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate, etc. made out of 1.25mm thick MS sheet complete all as specified and directed.

S&F of 125x60 mm pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate, etc. made out of 1.25mm thick MS sheet complete all as specified and directed.

S&F of factory made solid panel PVC door shutter 30 mm thick consisting of frame made out of MS tube for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 2mm width stuck inside with solvent cement for stiles and plain colur PVC sheet for top rails, lock rail & bottom rail, panel will be of wire gauze in lieu of PVC Sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube. The wire gauge shall be stretched to tighten firmly complete all as specified and directed.

S&F of machine moulded factory made 40 mm thick flush shutters, solid core construction with block board core and ply wood face panels, decorative type on both sides and fixed to chowkats complete all as specified and directed.

S&F of solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F of factory made solid PVC moulded door shutter with particle board core 32 to 35mm thick (style) with 2, 4 or 6 raised panel design with 2mm thick 3D plain colour PVC sheet on the front face and 2mm plain colour PC sheet on back face complete all as specified and directed. Make: Sintex Industries/ Poly WIndows/ Dura Plast/ Accucell as approved by GE

S&F in repairs to double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F in repairs to aluminium (extruded section body) door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters upto 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and directed.

S&F of butt hinges 100mm size, extruded aluminium alloy with galvanised mild steel hinge pin, anodised type B-21 and fixed complete all as specified and directed.

S&F of butt hinges 100mm size medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F of butt hinges 125mm size medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F of 150 mm long aluminium handles, cast type, anodised fixed to shutters complete all as specified and directed.

S&F of 150mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed to frames complete all as specified and directed.

S&F in repairs to stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed to frames complete all as specified and directed.

S&F of 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

S&F of 300mm ordinary MS rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L in repairs 25mm stainless steel drepary curtain rod decorative type including curtain fancy type brackets & nobs complete all as specified and directed.

Dismantling wall and ceiling boards of any description fixed in any position, any thickness including cover fillets complete all as specified and directed.

S&F of galvanised cold rolled steel section framed work size 600x600mm grid size, 24x38x0.60mm tee (bottom precoated) and 24x24x0.50mm thick wall angle galvanised cold rolled steel section including expansions fasteners as in ceiling compete all as specified and directed. Make: Gabson or equivalent as approved by GE.

S&F of 6mm thick exposed metal frame ceiling calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid complete all as specified and directed. Note: Frame work for ceiling shall be measured and paid separately.

S&F of 40mm wide of flap continuous (piano) hinges, brass, bright finish complete all as specified and directed.

S&F in repairs prelaminated particle board 18/19 mm thick, exterior grade, prelaminated both side with decorative choice lamination fixed with nails to aluminium framed work and fixed complete all as specified and directed.

S&F of 100mm stainless steel handle, cast type, polished bright complete all as specified and directed.

S&F in repairs 18mm plywood grade BWR, type BB fixed with screws to timber frame work complete all as specified and directed.

S&F in reapirs 0.9mm thick decorative laminated type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer instructions complete all as specified and directed.

S&F in repairs to cabinet hinges soft close SS 8 crank and fixed complete all as specified and directed.

S&F in repairs to 40mm long magnetic catcher for cupboard shutter complete all as specified and directed. Make: Hettich or equivalent as approved by GE.

S&F of kitchen baskets with 100% stainless steel, non-magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism kitchen capable of holding plates, cup, saucers, bowls and dongas with 500mm car case depth of 558mm and height 100mm complete all as specified and directed. Make: Life time-code: DSN 21 or equivalant as approved by GE.

S&F of kitchen baskets with 100 % stainless steel, non-magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism kitchen capable of holding plates, cup, saucers, bowls and dongas with 500mm car case depth of 558mm and height 150mm complete all as specified and directed. Make:- Life time-code: DSN 21 or equivalant as approved by GE.

S&F of kitchen baskets with 100 % stainless steel, non-magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism kitchen capable of holding plates, cup, saucers, bowls and dongas with 500mm car case depth of 558mm and height 200mm complete all as specified and directed. Make:- Life time -code: DSN 21 or equivalant as approved by GE.

Taking down cement plaster on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on any faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on any faces of brick/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5 mm thick rendering in CM 1:3 on brick/ concrete surfaces as in ceiling finished even and smooth without using extra cement complete all as specified and directed.

S&F in repairs to cascade type wash down water closet with seat cover, waste pipe, cistern with lid & fittings (complete set) and fixed complete all as specified and directed. Make: Hindware/ Cera/ Parryware as approved by GE.

S&F in repairs stainless steel towel rack 600mm long complete all as specifed and directed.

S&F in repairs vitreous china squatting pan Orissa pattern 580x440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including cement concrete bedding and making good disturbed surfaces complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (padestal pattern), white (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 Ltrs capacity with all internal fittings including flush pipe and fixing to WC complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size 550x400mm excluding tap but including brackets/CP brass 32mm waste coupling and waste pipe complete all as specified and directed.

S&F in repairs stainless steel sink, 1.00mm thick for kitchen, with plug, washers, waste coupling, waste pipe including bedding in cement mortar to dwarf wall or fixing with cantilever brackets and connecting union to pipe, overall size 495mm x 420mm with bowl size 410mmx330mm x160mm complete all as specified and directed.

S&F in repairs 15 mm angle valve stop cock cast copper alloy, screwed down high pressure chromium plated fancy type screwed both ends for iron pipe or unions and fixed complete all as specified and directed.

S&F in repairs 15 mm bib taps cast copper alloy, screwed down high pressure chromium plated fancy type screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15 mm pillar taps cast copper alloy with capstan head, chromium plated screwed down high pressure with or without lettered hot or cold with long shanks and fly-nuts screwed for iron pipes and fixed including necessary small GI fittings complete all as specified and directed.

S&F in repairs to 15 mm wash basin mixer, centre hole, mixing hot and cold water, cast copper alloy, chromium plated fancy type, with capstan head, screwed down high pressure for iron pipe etc and fixed complete all as specfied and directed.

S&F in repairs CP Health faucet suitable for 15mm bore with 1.2m flexible pipe and connecting pieces including all necessary accessories complete all as directed.

S&F in repairs stainless steel overhead square shower of size 150mmx150mm with arm and fixed to 15mm dia pipe complete all as specified and directed.

S&F in repairs 15mm wall mixer with provision for bath telephone shower and overhead shower cast copper alloy, chromium plated fancy type, with capstan head, screwed down high pressure for iron pipe etc and fixed complete all as specfied and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repairs plastic water closet seat cover, any colour, closed pattern with flat bottom and mild steel chromium plated for aluminised hinging device complete all as specified and directed.

S&F in repairs hydraulic plastic water closet seat cover, any colour, slow motion/ soft closure complete all as specified and directed. Make: Hindware /Parryware /Prayag as approved by GE.

S&F of tubular towel rail chromium plated 20 mm dia D type 60 cm long between flanges complete all as specified and directed.

S&F in repairs 15 mm bib cock two way with flange, cast copper alloy, fancy type, chromium plated screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15 mm angle valve two way with flange, cast copper alloy, fancy type, chromium plated screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs 3mm thick looking mirror of approved quality with wooden back and edge bedding and fixed complete all as specified and directed.

S&F in repairs 10mm thick glass shelf (with bracket) of 22 inch long chromium plated and fixed complete all as specified and directed.

S&F in repairs 10mm thick corner glass shelf (with bracket) of 25mm radius complete all as specified and directed.

S&F in repairs CP toilet paper holder with stainless steel flap complete all as specified and directed.

S&F in repairs soap dish holder of bottom CP and glass holder for soap complete all as specified and directed.

S&F in repairs CP towel ring round with round flange complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated, etc) sheets including ridges in roof covering complete all as specified and directed.

Dismantling timber in fillets rails, posts, rafters, purlins, etc under 40 Sqcm in section unframed work complete all as specified and directed.

S&F of pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet of 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

S&F of pre-painted galvalume aluminium zinc coating GI based plain steel sheet of 0.50mm thick of any colour having tensile strength of 550Mpa as in ridges and similar work fixed with self tapping screws complete all as specified and directed.

M&L for 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations sid lap fixed with L type or J type or cranked hook bolts complete all as specified and directed.

M&L for preparation of new or previously untreated surface of steel and iron of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hingsor steel hanging door fittings (including of steel sheeting or other covering Fe-410-W(Gde-E250) complete all as specified and directed.

M&F for mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F of steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 complete all as specified and directed.

S&F of mild steel work as in bands, straps, clamps, hold fasts, wall ties, hooks for hanging fans and similar articles complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc; (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed.

S&F of 75 mm dia PVC(SWR) pipes single socketed in any length with rubber rings joints laid in trenches or in floors complete all as specified and directed.

S&F of 110 mm dia PVC(SWR) pipes single socketed in any length with rubber rings joints laid in trenches or in floors complete all as specified and directed.

S&F of 75mm bore PVC(SWR) bend complete all as specified and directed.

S&F of 75mm bore PVC(SWR) junction single (single 'T') equal or unequal complete all as specified and directed.

S&F of 75mm bore PVC(SWR) vent cowl complete all as specified and directed.

S&F of 110mm bore PVC(SWR) vent cowl complete all as specified and directed.

M&L for PVC(SWR) floor trap plain with grating including jointing with solvent cement 75mm bore complete all as specified and direcetd.

S&F of 110mm bore PVC(SWR) bend and fixed complete all as specified and directed.

M&L for grinding and polishing kota/marble/terazoo/mosaic flooring complete all as specified and directed.

Dismantling of water tanks of exc 250 litres but n.exc 500 litre capacity complete all as specified and directed.

Dismantling of water tanks of exc 500 litres but n.exc 1000 litre capacity complete all as specified and directed.

S&F of 500 ltrs capacity rotational moulded polyethylene water storage tanks 3 layers(cylindrical vertical with closed top) triple layer hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F of 1000 ltrs capacity rotational moulded polyethylene water storage tanks 3 layers (cylindrical vertical with closed top) triple layer hoisted and fixed in position complete all as specified in SSR Part-I and directed.

S&F of 20 mm dia ball valve PTMT, high pressure with polythene float and fly nut, screwed for iron pipe with epoxy coated aluminium rod complete all as specified and directed.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

Taking down existing old roof treatment of any description, any type including removal of old Tar felt, screed bed and plastering etc complete all as specified and directed.

M&L for preparing RCC roof surfaces with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particle and applying APP modified bituminous water proofing membrane with polyester reinforcement and plain finish of 3 mm thick (total weight of the finished membrane not less than 3.8 kg/ sqm ± 5 % per sqm) confirming to IS 16532: 2017 over a coat of bitumen 85/25 @ 1.2 Kg/ sqm by the same membrane manufacture of density at 25⁰C, 0.87-0.89 kg/ litre and viscosity 70-160 cps, laying over the primer coat using butane torch and sealing all joints, overlapping etc. as per Annex D of IS 16532: 2017 with and including ponding test by filling 75 mm deep water over roof treatment by making necessary arrangement to fill the roof slab at least for 72 hrs complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in benching/angle filleting at the junction of parapet and RCC roof complete all as specified and directed.

M&L for cutting grooves or chase in brick wall, 75 mm wide and 65 mm deep and including filling with cement mortar 1:4 mixed with water proofing compound complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:4 over RCC slab mixed with water proofing compound @ 3% by weight of cement or manufacturer instruction complete all as specified and directed. Note:- Water proofing compound shall be measured and paid separately.

M&L for cement concrete M15 (Nominal Mix) using 12.5 mm nominal size graded crushed stone aggregate mixed with water proofing compound as levelling course of roof padding finished even and fair complete all as specified and directed. Note:- Water proofing compound shall be measured and paid separately.

M&L for grout of permanent bonding of strutural damage/crack, porosity of concrete to attend leakage/seepage with pressure grouting with 15mm bore GI Pipe nozzle under the pressure of 5 kg/sqcm using cement based grout, treatment to be made as per manufacturer instructions complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls by brooming, scraping down, smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and applying one coat of white wash on walls complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling by brooming, scraping down, smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and applying one coat of white wash on ceiling complete all as specified and directed.

M&L for complete removal of old decorated surface of wall/ceiling and applying two coats of oil emulsion distemper white/tinted over one coat of white cement based putty complete all as specified and directed.

M&L for preparation of old decorated surfaces of wall/ceiling including brooming, scraping down, smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and apply one coat of oil emulsion distemper complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of oil emulsion distemper white/tinted over a coat of wall primer complete all as specified and directed.

M&L for preparation of old decorated surfaces of wall including brooming, scraping down, smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and applying one coat of exterior weather proof water base emulsion paint on wall complete all as specified and directed.

M&L for removal of old decorated wall surfaces and applying two coats of exterior weather proof water base emulsion paint over a coat of wall primer complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of exterior weather proof water base emulsion paint over a coat wall primer complete all as specified and directed.

M&L for preparation of old painted surfaces of wood/wood based materials of any description exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted surfaces of iron/steel materials of any description exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for 3mm thick coat of wall care putty on walls/ceiling, finished even and smooth complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregate) louvres and jallies, 35mm thick (measured solid), including all mouldings but excluding frame complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block (reflective type) any shape and size with grey cement and pigment confirming to IS 15658-2006 of 60mm thickness, M-35 grade including 50mm stone dust layed in floors or paving etc spread, levelled and rammed including watering complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block (reflective type) any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80mm thickness, M-40 grade including 50mm stone dust layed in floors or paving etc spread, levelled and rammed including watering complete all as specified and directed.

S&F in repairs to solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet used instead of plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and directed.

S&F in repairs to 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on wall to make PVC frame as per specification and drawing complete all as specified and directed.

S&F in repairs to factory made single extruded WPC (wood polymer composite) solid door/ window/ceosetory windows & other frames/chowkhat of size 65mm x100mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic aditives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as per specified and directed.

S&F in repairs to factory made single extruded WPC (wood polymer composite) solid door/window/ceosetory windows & other frames/chowkhat of size 65mm x125mm comprising of virgin PVC polymer of K value 58-60(suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic aditives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed.

S&F in repairs factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed.

S&F of GI frame work size of grid 605 mm x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylone sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kuled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed.

M&L for providing and fixing 12mm gypsum board ceiling fixed with and including GI angle/ channel frame work including GI wire/ mesh, etc in different levels including joints filled with paster of paris, putty including POP work/ cornices and applying two coats of oil bound distemper complete all as specified and direcetd.

Dismantling of structural steel work including doors,gates etc complete all as specified and directed.

S&F in repairs half stall vitreous china urinal white colour of size 710x480x300mm, Ist quality with sensotrinic, sensor flushing valve with kit including CP waste with PVC down waste pipe upto floor level (complete set) complete all as per manufacturer instructions and directed. Make: Jaquar (Cat No. URS-WHT-0704, SNR-51097) or equivalent as approved by GE.

M&L for petty repairs to half stall vitreous china sensor type urinal with and including changing of sensor of flushing valve with kit complete all as specified and directed.

S&F of polycarbonate switch piano, flush button, single pole, one way 5 Amp, 240 V, ISI marked complete all as specified and directed.

S&F of polycarbonate switch piano, flush button, single pole, two way, 5 Amp, 240 V, ISI marked complete all as specified and directed.

S&F of polycarbonate ceiling rose, surface type, 3 terminal, 240 V, ISI marked complete all as specified and directed.

S&F of polycarbonate socket outlet 2-in-1, 5 pin 5 Amps, 240 volts, flush type complete all as specified and directed.

S&F of polycarbonate switch socket combo outlet flush type multipurpose 2 in 1, 3 pin, 5 and 15 Amp, 230 volts complete all as specified and directed.

S&F of polycarbonate switch piano flush button single pole one way 15 Amp 240 volt ISI marked complete all as specified and directed.

S&F of polycarbonate socket piano flush button single pole one way 15 Amp 240 volt ISI marked complete all as specified and directed.

S&F of stepped type electronic fan regulator, delux model, 100 watt, 240 V, flush type complete all as specified and directed.

S&F in repairs lamp holder, PVC/Poly carbonate type with back plate suitable for batten fittings with and including 9 watt LED lamp and and making necessary connections complete all as specified and directed.

S&F of buzzer, ding dong AC 230 volts, single pole complete all as specified and directed.

S&F bell push, flush type, single pole, 5 Amp, 240 V complete all as specified and directed.

S&F in repairs MCCB, TPN, 100 Amps, 10 KA breaking capacity, 'C' curve including making connection with suitable size aluminium/ copper lugs complete all as specified and directed.

S&F in repairs MCCB, TPN, 63 Amps, 10 KA breaking capacity, 'C' curve including making connection with suitable size aluminium/ copper lugs complete all as specified and directed.

S&F of MCB, SP, 5 to 32 Amps, 240 volts, 10 KA breaking capacity, 'C' curve including making connection with suitable size aluminium/ copper lugs complete all as specified and directed.

S&F of MCB, SPN, 5 to 32 Amps, 240 Volts, 10 KA breaking capacity, 'C' curve including making connection with suitable size aluminium/ copper lugs complete all as specified and directed.

S&F of MCB, TPN, 40 to 63 Amps, 240 Volts, 10 KA breaking capacity, 'C' curve including making connection with suitable size aluminium/ copper lugs complete all as specified and directed.

S&F in repairs LED tube light box type highly durable surface mounted LED batten constructed of fire retardant engineering grade extruded plastic and decorative end caps, 18/20/22/25 Watt (reterofit type, T8 pattern, single side connection) 240 V, PF > 0.90, colour Temp 6500 K, System Luminious efficacy > 100Lm/W, approx length 4 feet to be fixed in existing or new batten with and including making necessary connections suitable for tube light fitting complete all as specified and directed. Make :- Bajaj / Havells/ Philips or as approved by GE.

S&F in repairs surface mounted economical LED panel light 1 ft x 1 ft, 18/20 watt with high quality diffuser for uniform light, CRCA housing, separate replaceable electronic driver, suitable for recess and surface, CRCA panel 18/20 ECW including LED lamp, nuts, wire and all connected accessories complete all as specified and directed. Make: Bajaj/ Havells/ Philips or as approved by GE.

S&F of panel light, square type 2 ft x 2 ft of 40/36W, CRCA housing color temperature 3500 - 4100 K, AC 220 -240 V, 50 Hz, high surge protection 2.5 KV, ISI marked, Lumen>4000, working life time hour 50000 pc lens for better light distribution including nut, led lamp, suitable for recess and surface wire all connecting accessories complete all as specified and directed. Make: Bajaj/ Havells/ Philips or as approved by GE.

S&F in repairs LED 9/10 Watt mirror tube light fitting intergated type, approx 2 ft, 240 V, PF>0.90, colour Temp 6500 K, suitable for surface mounting on wall including connecting with PVC insulated multistranded copper flexible cable 0.5 Sqmm two core and PVC round block white colour x 2 Nos for mounting of fitting complete all as specified and directed. Make: Bajaj/ Havells/ Philips or as approved by GE.

Taking down unserviceable service cable any type and size and supplying, laying and fixing or passing through pipe, 1100 volt grade heavy duty PVC insulated multi stranded alunimium conductor cable served with an inner sheathed of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed 16 Sqmm x 4 core nominal cross section in service connections complete all as specified and directed.

Taking down unserviceable service cable any type and size and Supplying, laying and fixing or passing through pipe, 1100 volt grade heavy duty PVC insulated multi stranded alunimium conductor cable served with an inner sheathed of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed 25 Sqmm x 4 core nominal cross section in service connections complete all as specified and directed.

S&F in repairs building secutity light 22 Watt with and including 32mm bore GI pipe light grade of approx 1m length including weather protection cover nut IP 54, bolt and connected accessories complete all as specified and directed. Make: Bajaj/ Havells/ Philips or as approved by GE.

S&F of 9 Watt LED bulb, 220 volt, 50 Hz complete all as specified and directed. Make: Bajaj/ Havells/ Philips or as approved by GE.

S&F of cable 1 Sqmm x 3 core multi stranded copper flexible wire FRLS, 220 Volts, 50 Hz complete all as specified and directed.

S&F of quarter pin for fans complete all as specified and directed.

S&F in repairs 3 pin plug top, 230 V, 15 Amp complete all as specified and directed. Make : Anchor/ L&T/Havells

S&F in repairs 3 pin plug top, 230 V, 5 Amp complete all as specified and directed. Make : Anchor/ L&T/Havells

S&F in repairs laminated hylum sheet cover, ISI marked of Make" Hylem" including cutting grooves for mounting of fittings like switches, sockets, fan regulators etc; including fixing in location with new galvanised screws and cup washer complete all as specified and directed of following sizes:-

11 x 13 inches

9 x 11 inches

5 x 8 inches

5 x 5 inches

S&F in repairs condenser 2.5 mfd complete all as specified and directed. Make: Epcos/Tibcon

S&F in repairs condenser 4 mfd complete all as specified and directed. Make: Epcos/Tibcon

Deduct Schedule of credit (calculation will be done off line) Rs. 44323.00

Samaksh Enterprises

MS MOHD RIZWAN KHAN