BWN/Rs. 3.47 Lacs/Special repair of toilet in Judicial Court Complex at bhiwani in Bhiwani Distt.

Amount

Removing door and windows (wood and steel) with chowkats by making recesses in walls when the walls is not to be dismantlled doors (H.S.R item 8.18 (a))

Dismantling cement conglemerate / terrazzo floors 25 mm to 50 mm thick including concrete base(H.S.R. 8.25)

Dismantling white or coloured glazed tiles (to be carefully removed)(H.S.R 8.38)

Providing & Fixing PVC Rain water pipe 6KG pressure of ISI mark in cement mortrar during masonry work (H.S.R 13.89 A) 100mm dia PVC pipe 6 Kg. presure

Base course of floors consisting of 100 mm thick cement 1:8:16 and 100 mm sand or stone filling (HS.R. 14.1)

Providing and fixing ceramic tiles/anti skifd tiles of size 400 mm x 400 mm or above size of approved make in flooring. Laid in any pattern as specified over base of 20mm thick cement coarse sand mortrar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. NOTE:- Tile shall be of premium quality (First Quality) of repiuted manufacturer like NICTO,KAJA-RIA, SOMANI, ORIENT & JOHNSONS (H.S.R 14.91)

Providing and fixing Iat qualiuty ceramic glazed wall tiles conforming to I.S. 15622 (thickness to be specified by the manu-facture of approved make in all colours, shades except burgundy bottle green , black of any size as approved Engineer-in-charge in skirting riser and dados over 12mm thick bed of cement mortrar 1:3 coarse and jointed with grey cement slurry including pointing inwhite cement mixed with pigment of matching ceramic glazed tiles 300x450mm (HSR 14.92(b)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawel plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. Aluminium sections shall be smooth, rust free straight mitered and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/paneling C.P brass/stainless steel screws, etc. complete shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC/neoprene gasket required including aluminium fitting. (HSR 17.96+Note (i)].

Providing and fixing 12 mm thick preleminated paticle board flat pressed three layer or graded wood particle board conforming to IS;12823 grade I type II in paneling fixed in aluminium doors. Windows shutters and partition frames with c.p brass / stainlees steel screws etc. complete (b) Pre-laminated particle board with decorative lamination on both sides. [HSR 17.97 (b)].

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE LARGE FLAT BACK OR Angular lipped front Urinal 610MM High consisting of. Flat back lipped or angular urinal basin or VITEROUS CHINAWARE ; (to the approval of the Engineer-in-charge) (H.S.R 30.25 i)

Providing and fixing 25mm thick marble partition for different type of urinals. H.S.R 30.40 BII(i) Large 835mm x 355mm

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the approval of the Engineerin-charge) including china plug for tap hole where necessary ; R.S. or C.I.BRACKETS for building into wall including painting; 32mm C.P.BRASS WASTE WITH C.P. brass chain and rubber plug; 15mm C.P.BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and MAKING GOOD THE WALLS, FLOORS AND PAINTING OF FITTINGS ETC.(H.S.R 30.41 iii) Size 610mm X 510 mm

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineerin- charge) Concealed stop cock with flange (H.S.R 30.76 aii ) 15 MM STOP COCK

Providing and fixing in position C.P. brass stop cocks (as approved by the Engineerin- charge) Stop cock with flange H.S.R 30.76 (b-ii) 20 MM STOP COCK

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE EUROPEAN TYPE WATER CLOSET SUITE WITH CONCEALED ‘P’ or ’S’ TRAP with or without vent (as approved by the Engineer-in-Charge) and all other necessary fittings as fully described in item no.30.3 above. (HSR 30.6 (i)

Recovery Item The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer and granular layers have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under :- Door Iron 10 Nos. (10x25 Kg/Each = 250 Kg x @ Rs. 22/- P.Kg. Each Note: All quantities of the below materials have been worked out on the basis of theoretical quantities laid on this road. However, agency may visit site before quoting rates and assess the extent of retrieved material. There shall be no measurement after actual dismantling and if material after dismantling is found on lesser side, no claim of agency on this score will be entertained and full recovery on the basis of quoted rate and quantity exhibited in the BOQ shall be made. The reserve rates are minimum rates to be used as base for quoting purchase rate by the agency. No rates below the reserve price will be entertained and reserve price will be considered for all purposes in case the agency quotes lesser than reserve price. Note:- 1. In case of any difference in the unit & nomenclature of any of the HSR/DSR Items of Civil, P.H., & E.I. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable. 2. Only reputed make material will be used (make/brand exhibited in HSR/DSR and exhibited in approved standard document) as approved by Engineer-in-charge, while executing various items/works at site.