REPAIR/REPLACEMENT OF FENCING, BOUNDARY WALL, DRAIN AT PRATAP ENCLAVE AND REPAIR/ REPLACEMENT OF PATH, DRAIN AND MISC WORKS AT NIRMAN VIHAR UNDER ZONE-I AREA AT JAIPUR MIL STN

Amount

M&L preparation of old concrete surfaces of any description over 10cm girth or width not otherwise described and applying one coat of synthetic enamel paint complete all as specified.

All as per item Ser No 1 but two coats of synthetic enamel paint complete all as specified

M&L preparation of old surface of walls and applying one coat of cement paint of any tint all as directed.

All as per item Ser No 3 but two coats of cement base paint of any tint all as directed.

M & L preparation of old steel surfaces and applying one coat of synthetic enamel paint all as specified

Demolition of cement concrete in ground floors and paving not exc 15cm thickness (below or above ground level)

M&L broken stone or boulders for hardcore, gauge not exc 63 mm size deposited spread and levelled in layers n exc 15 cm thick watered and rolled /rammed to a true surface all as directed.

M&L plain cement concrete 1:4:8 type D-2 (40mm graded aggregate) in sub base of floors

M&L 75mm thick plain cement concrete 1:2:4 type B-2 (40mm graded aggregate) in sub base of floors

M&L 40mm thick plain cement concrete 1:2:4 type B-1 (20mm graded aggregate) in sub base of floors

Demolition stone slabs and tiles of any description or thickness in floors, aprons etc laid,bedded and pointed in cement mortar

M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with grey cement and pigment laid over and including 25mm thick sand cushion layer complete

All as per item Ser No 12 but except tiles.

M&L rubber moulded Chequered cement concrete tiles 20cmx20cmx20mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment over 20mm thick screed bed in 1:6

All as per item Ser No 14 but except tiles.

M&L for granite (of any type), 16mm to 18mm work (table rubbed and polished) in steps, jamps, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L for Dholpur stone 16 to 18mm cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with and including one number SS clamps (grade -202) of flat 30mm X 2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment

M & L machine cut kota stone slab flooring 20-25mm thick,size of kota stone 450x450 mm over and including cement screed base 20mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L precast PCC blocks or slabs 150mm thick (1:2:4) mix type B-1 using 20mm graded aggregated with plain or interlocking joints as directed complete in walls setting in CM (1:6)

Demolition of precast RCC jallies including raming of any description any in any position set in cement morter complete all as specified

M&L prividing precast cement concrete (1:2:4) louvers and jallies 35mm thick (measured solid) including all mouldings but excluding frames & set in CM 1:4

Demolition of un-reinforcement cement concrete in ground floors and pavings not exc 15cm thickness (below or above ground level)

M&L precast reinforced cement concrete slab type B1, 1:2:4 (20mm graded aggregate) as in landings, drain cover slab (for manholes etc) chajjas, drain cover and shelves and similar articles with plain faces (Reinforcement shall be measured & paid separately).

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

All asper item Ser No 24 but 6mm to 8mm dia

Demolition of brickwork or stone/boulder masonry, built in lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles but built in cement mortar or cement lime mortar

M&L brick work with old size sub-class 'B' bricks straight or curved on plan exc 6.00 metre mean radius built in cement mortar 1:6 for raising of height of drain, manhole/wall complete all as specified.

All as per item Ser No 27 above but except bricks complete all.

Taking down cement plaster or cement lime plaster any descrption on stone surface/ brick surfaces of wall or ceiling including raking outs joint hacking for key scrubbing down with water etc

M&L for rendering 15mm thick on stone masonary surface or surface other than kfair faces of brick work or on one side of lathing in CM 1:6 finished even and smooth without using extra cement.

M&L for preparation of new plastered wall surface and applying two coats of cement base paint on wall.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

S&F rolled mild steel work as in joint, channel, angle or tee sections fixed independently without connecting plates, etc (cut to ordinary lengths i.e. within 20mm of the length directed) and similar work conforming to Fe-290 Gde E-165.

S&F mild steel work such as angle iron in posts & struts in fencing including cutting tops to shape hand rail straight portion drilled and contersunk for balusters, noising to steps, struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing chain link fencing) including or riveting etc and similar work conforming to Fe-290 Gde E-165.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete.

S&F in repair mild steel round bars, 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for chain link fencing (in new or old)

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in soft/ loose soil.

Dismantling galvanised chain link fencing of any description fixed to any type of fencing posts.

S&F 3mm dial galvanised steel wire 100 x 100mm mesh (chain link fancing) made up matress fixed to any type of std rails straining bolts etc incl provn of binding wire

S&F screw bolts (machine made) with hexagonal or square head at one head and rounded the other or screwed both end each screwed end to be fitted with washers and one hexagonal or aquare nut exc 10cm n exc 15cm long dia of shank 11 to 15mm

S&F as in repair galvanized 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossing with and provision of galvanized mild steel wire, staples or steel pins etc as directed.

M&L preparation of new steel surface of any description not exc 10cm width or girth when unconnecting to other painting surface and applying two coats of synthetic enamel paint over a coat of red oxide zink chrome primer.

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coarch screw and washer in roof wall etc.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strenth of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Dismantling plain or corrugated steel/FRP sheeting any guage, thickness including nainital or similar pattern roof/wall covering

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F steel work in tubular/square/rectabgular trusses incl special shaped washer etc, complete using ERW orinduction butt welded tubes conforming to IS 1161-1979 graded St-240

M&L for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified

M&L plain cement concrete (1:2:4) type B-1 (20 mm graded aggregates) as in lintels, cills steps seismic and other similar bands, copings, kneelers, apex stone bed plates, kerb, water troughs and like including weathering, slightly rounded or chamfered angles and throating as directed.

S&F Sign board made out of 03mm aluminium composite pannel both side alongwith retro reflective sheeting on both side with letters, stops, commas, short lines, dashes, hypen, brackets etc of 100-150mm size fixed on 75mm dia SS pipe of 3 mtr long all as specified and directed. Note 1. Area of sign board shall be considered for payment.

Schedule of Credit

M/S Mohan Lal Gupta

agrawal constructions

M/S S R CONSTRUCTION

MSR INFRATECH

NARAYAN SINGH NARENDRA SINGH AND COMPANY

S.R.Enterprises

Narayan Enterprises

Deep Construction Company