Special repair to 1 BD single OR toilet 354 Fd Hosp False ceiling of E61 Ration store 16 Bihar Open drain at 383 Block OR MD accn and Provn of Septic Tank incl connecting sewage line of Bldg 1 2 11 and 12 single OR Toilet 354 Fd Hosp under GE Golcond

Amount

Surface dressing n exc 15cm deep and getting out in hard/dense soil

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.50m in depth and getting out in soft / loose soil all as specified and directed.

Excavation over areas not exceeding 1.5 m in depth and getting out in soft / loose soil all as specified and directed.

Excavation over areas exceeding 1.5 m and n.exc 3.0m in depth and getting out in hard/dense soil all as specified and directed.

Excavation over areas exceeding 3.0 m and n.exc 4.5 m in depth and getting out in hard/dense soil all as specified and directed.

Excavation over areas exceeding 4.5 m and n.exc 6.0 m in depth and getting out in soft / disintegrated rock soil all as specified and directed.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth and getting out in hard/dense soil all as specified and directed.

Returnng, filling in, soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm all as specified and directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed.

M&L for hardcore using broken stone or boulders not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface all as specified and directed.

Supply only Broken brick coarse aggregate/bats exc. 63 mm size

Demolition of cement concrete n.exc 15cm thick unreinforced above/below ground floor complete all as specified and directed.

Demolition of cement concrete unreinforced in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work etc complete all as specified and directed.

Demolition of Brick works masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and pre-cast concrete articles complete all as specified and directed

Demolition of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing the rubbish off the premises complete all as specified and directed.

M&L Plain cement concrete (1:4:8) type D2 (40mm graded stone aggregate) in foundations, filling and mass concrete all as specified and directed.

M&L Plain cement concrete (1:2:4) type B2 (40mm graded stone aggregate) in foundations, filling and mass concrete all as specified and directed.

M&L for pre-cast Reinforced cement concrete (1:2:4) type B1 (20 mm graded stone aggregate) as in cover slabe for manholes etc., and set in cement mortor (1:4) all as specified and directed. Note: (i) Cost of formwork reqd is deemed to be included in item rate quoted. (ii) Reinforecement will be measured and paid separately.

M&L for Plain cement concrete (1:2:4) type B1 (20 mm graded stone aggregate) as in coping, benching, bed blocks, cills and like rounded or chamfered where required including necessary form work , complete all as specefied and directed.

M & L for Reinforced Cement Concrete (1:2:4) type B1 (20 mm graded stone aggregate) in baffel walls etc., complete all as specified and directed.

M&L for Reinforced Cement Concrete (1:2:4) type B1 (20 mm graded stone aggregate) slabs supported on walls, beams and columns in floors, roofs, landings balconies canopies, desk slabs and in shelves etc., complete all as specified and directed.

M&L for Providing precast cement concrete type B1 using 20 mm graded stone aggregate set in Cm 1:4 as in Baffle wall and similar articles with plain faces.

Supply only integral water proofing compound

M&L Brick work with fly ash bricks built in cement mortar (1:6) straight or curved on plan exceeding 6 mtr mean radius all as specified and directed.

Use & waste formwork to sides of concrete baffel walls and similar work, flat, rough finished surfaces, complete all as specified and directed.

Use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide etc., flat rough finished surfaces, complete all as specified and directed.

Use & waste of formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surface, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sqm but n exc 4.00 Sqm each complete all as specified and directed.

S&F for solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing as per specification and drawing all as specified and directed.

S & F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and directed.

M & L for eaves board, weather board with 2nd class hardwood planed one sides fixed with butt joints 20 mm thick

M&L for 2nd class hard wood scantling as in purlings, rafter complete all as directd and specified.

S&F for 100 mm long extruded Aluminium alloy butt hinges with galvanised mild steel hinge pin and fixed complete all as specified and directed.

S&F for 125mm long aluminium anodized barrel tower bolts of extruded section and fixed.

S&F for 150 mm long alluminium alloy anodized handles fabricated type

S&F Mild steel TMT bars 6 to 8mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips) complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L Plain cement concrete (1:3:6) type C2 (40mm graded stone aggregate) 75mm thick as in sub base of flooring/hardstanding complete all as specified and directed.

M&L Polished shahabad stone slab 20-25 mm thick as in skirting over and including 10mm thick back coat in CM 1:3 and jointed with white cement slurry mixed with pigment to match the shade of the shahbad stone slab including grinding and polishing making smooth surface etc complete all as specified.

M&L Polished shahabad stone slab 20-25 mm thick as in flooring laid over and including 20mm thick cement mortar screed in CM 1:6 and jointed with white cement slurry mixed with pigment to match the shade of the shahbad stone slab including grinding and polishing making smooth surface etc complete all as specified.

M&L for chequred cement concrete tiles 20 cm x 20 cm x 25 mm thick with grey cement and pigment, machine pressed : set, jointed and pointed in neat cement slurry, laid over including 15 mm thick screed bedding layer in cement mortar (1:6) all as specified and directed.

M&L Plain cement concrete (1:2:4) type B0 (12.50mm graded stone aggregate) as in roof padding complete all as specified and directed.

S&F for non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors laid over and including 20mm thick screed bed or bedding layer in cement mortar (1:6), tiles jointed in neat cement slurry and pointed with white cement mixed with pigment to match the colour of tiles all as specified and directed.

S&F for glazed ceramic coloured tiles of size 300x200x7mm thick for vertical surfaces as in dado/skirtings set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles laid over and including backing coat in cement mortar (1:4), 10mm thick all as specified and directed.

M&L for Rendering 15mm thick in cement mortar (1:3) mixed with water proofing compound on fair faces of brick work / concrete surfaces finished even and smooth without using extra cement, complete, all as specified and directed. Note: Supply only water proofing compound will measured and paid separately.

M&L for Rendering 15mm thick in cement mortar (1:4) on fair faces of brick work / concrete surfaces finished even and smooth without using extra cement, complete, all as specified and directed.

Taking down cement or cement limes plaster on brick or stonewalls including ranking out joints, hacking for key, scrubbing down with water etc.

M&L Rendering 10mm thick on brick work or concrete surface as on walls in cement mortar (1:6) and finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 5 mm thick in ceilings with cement mortar (1:3) and finished even and smooth without using extra cement, complete all as specified and directed.

M & L for Preparation of new plastered wall surfaces and apply three coat of white wash, complete all as specified and directed.

M & L Preparation of new plastered ceiling surfaces and apply three coats of white wash, complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and apply two coats of cement based paint over a coat of cement primer all as specified and directed.

M & L preparation of old decorated surfaces of walls plastered or unplastered by brooming down or steel wire brushing, scrapping down smoke soots, moulds, moss and efflorecent salts and treading oil and greasy spots etc and applying one coat of white wash .

M & L preparation of old decorated surfaces of walls plastered or unplastered by brooming down or steel wire brushing, scrapping down smoke soots, moulds, moss and efflorecent salts and treading oil and greasy spots etc and applying one coat of cement based paint complete all as specified and directed.

M & L preparation of old decorated surfaces of ceiling plastered or unplastered by brooming down or steel wire brushing, scrapping down smoke soots, moulds, moss and efflorecent salts and treading oil and greasy spots etc and applying one coat of white wash .

M & L preparation of old decorated surfaces of walls plastered or unplastered by brooming down or steel wire brushing, scrapping down smoke soots, moulds, moss and efflorecent salts and treading oil and greasy spots etc and applying two coats of oil bound distemper over a coat of alkaline primer, white or tinted complete.

M & L preparation of old decorated surfaces of walls plastered or unplastered by brooming down or steel wire brushing, scrapping down smoke soots, moulds, moss and efflorecent salts and treading oil and greasy spots etc and applying two coats of cement based paint complete.

M & L for preparing surfaces of wood and wood based materilas, new or old of any description and girth, not otherwise described and treated with two coats of creosote complete all as specified and directed.

M&L Preparation of old wood or wood based surfaces exceeding 10cm width & girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

S&F Galvanised corrugated mild steel sheeting 0.63mm thickness with two corrugation side lap, fixed with L or J type or cranked hook bolts with washers, in roofs, walls etc with zinc coating 275 Gm/ Sqm including dismantling old AC corrugated sheeting (with ridge) all as specified and directed.

S&F Plain galvanised mild steel sheeting in ridges, hips, valley gutters, drip and straight flashing (length and girth as fixed) 0.60 mm thick with zinc coating 275Gm/Sqm etc complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation,etc.) or insulation boards/slabs/blankets any thickness, incl cover filltets and grids.

S&F true horizontal level 600x600mm panels false ceiling system using hot dipped galavnized steel sections, exposed surface with pre-coated capping, Main Tee of size 24x32mm at every 1200mm c/c maximum, rotary stitched cross Tee of size 24x 27 mm at every 1200mm c/c and wall angle of size 19x19mm fixed to perimetre wall. The complete grid is to be suspended at every 1200mm c/c in both directions by using 2mm dia pre straightened GI wire at every 1200mm interval at the main Tee using fine finished tagular edge, including provision of 9mm thick Gypsum boards of size 600 x 600 mm with rear side aluminium foil and front side finished with PVC lamination complete all as specified.

S&F Rolled mild structural steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe 410-W (Gde-E) all as specified and directed.

S&F Framed work such asrungs, grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L Reinforced concrete pipes 200 mm dia bore, class NP2, laid and jointed complete with collars laid in trenches and jointed as complete all as specified and directed.

M&L for Cement Concrete 1:3:6 type C-2 as concrete bed to drain pipes including forming cradles for pipes after they are laid and tested for 200 mm dia RCC pipes complete all as specified and directed.

M&L Reinforced concrete pipes 300 mm dia bore, class NP2, laid and jointed complete with collars laid in trenches and jointed as complete all as specified and directed.

M&L for Cement Concrete 1:3:6 type C-2 as concrete bed to drain pipes including forming cradles for pipes after they are laid and tested for 300 mm dia RCC pipes complete all as specified and directed.

S & F in repair vitreous china squatting pan (Orissa pattern) size 580 X 440mm white with integral foot rest, P or S trap set in and including concrete complete all as specified and directed.

S & F in repair PVC valveless, syphonic action type, flushing cistern, dual operated type, 10 ltr capacity, low level, white with inlet ball valve float and handle including brackets, with 32mm dia PVC pipe, complete all as specifeid and directed.

S&F for 15 mm dia PVC connections with PTMT nuts of length 600 mm, with check nuts complete all as specified and directed.

S & F tubular towel rail 20mm dia brass chromium plated D type 60cm between two flange all as specified

S &F in repair shower rose CP fix to iron pipe 15mm all as directed.

S & F for Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), etc complete all as specifed and directed.

S & Fin repair bib tap 15mm cast copper alloy with crutch or butterfly handle screwed for iron pipe and fixed all as specified and directed.

S & F in repair stop cock 15mm dia cast copper alloy screwed down high pressure with crutch or butterfly handle screwed for both end for iron pipe or for union and fixed all as specified and directed.

S&F steel water tubing, ‘medium grade’ galvanised, 15mm bore including all fittings to walls and ceilings or laid in floors/trenches including taking up or down existing tubing with fittings 15mm dia complete all as specified and as directed.

S&F steel water tubing, ‘medium grade’ galvanised, 20 mm bore including all fittings to walls and ceilings or laid in floors/trenches including taking up or down existing tubing with fittings 20 mm dia complete all as specified and as directed.

S & F for 110 mm dia PVC (SWR) junction single (Single T) equal or unequal with access Door.

S & F for 110 mm PVC (SWR) bends any radius all as specified and directed.

S & F for 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specifed and directed.

S & F PVC (SWR) vent cowl 110mm dia.

PVC (SWR) floor trap 75mm dia, plain with gratings including jointing with solvent cement

S & F in repair Vitreous china Urinal bowl flat back , size of 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe) including urinal waste pipe complete all as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm bore.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors for 110mm bore.

S&F PVC (SWR) bends any radius 75mm bore

M&L 1:3:6 type C1 (using 20mm graded stone aggregate) as in surface channels & drains complete all as specified and directed.

M&L salt glazed stone ware gully traps square or rounded mouthed type & fix 150 x 150 mm fixed in cement concrete complete.

M & L for APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (weight not less than 150 gms/Sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 Ltrs/Sqm by forced application and applying one coat bitumen grade 85/25 @ 1.2 Kg/Sqm over finished with one coat of alluminium paint @ 100 ml/Sqm 10cm overlap fused uniformly by LPG torch flame including 10mm thick screed in CM 1:4 mixed with WPC finished even and smooth with out using extra cement on concrete surfaces, complete all as specified and directed by Engineer-In-Charge. (Make: IWL/STP/TIKKITAR)

Taking out carefully copper/aluminium point wiring,Light,fan,socket or power complete with all fitting, fixtures such as switch socket out let, ceiling rose, holder, regulator, DBs etc including making good the disturbed surface of wall/floors complete.

M&L Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm multistrand copper conductor cable PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 1.50 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable ( green colour) as earth lead in and including PVC rigid conduit with all fittings for concealed type on stone / brick ,masonary walls, roof etc including in new MS sunk box of required size and all as directed by Engineer-in-Charge & 3 mm thick plastic laminated sheet for housing switches sockets, regulators etc, including running chases, pinning in and making good the disturbed surfaces to match with the existing specification ,complete all as specified and directed at site.

All as per ser item No 95 here in before but for one 3/5 pin multi socket outlet 5 Amp independent.

All as per ser item No 95 here in before but for one 3/5 pin multi socket outlet 5 Amp on same board.

All as per ser item No 95 here in before but for one 3/5 pin multi socket outlet 15 Amp independent board using cable of size 2.50 sqmm.

M&L switch piano flush type single pole one way 5 Amps complete all as specified and directed.

M&L lamp holder insulated body with back plate suitable for batten fittings complete all as specified and directed.

S&F Ceiling rose surface bakelite 65 x 50 mm 2/3 terminais complete all as specified and directed.

Supply and fix Switch socket outlet combination multi type, 2 in 1, 3/5 pin 5 Amp, piano flush type, 240 volts, complete all as specified and as directed at site.

Supply and fix Switch socket outlet combination multi type, 2 in 1, 3/5 pin 5 and 15 Amp, piano flush type, 240 volts, complete all as specified and as directed at site.

S&F Electronic fan regulator stepped type with five step 240 volts suitable for 1200/1400 mm sweep AC ceiling fan .

S&F 9 W INVERTER LED bulb of base B22d with color temp 6500K and upto 4 hrs backup all as specified and directed.

S&F LED tube light fittings 1 x 22 W, 230V, complete with all accessories internally prewired and including LED Tube rod connecting up with twisted flexible PVC copper conductor cable of 23/0.0079 from ceiling rose all as specified and directed.

S & F LED light fittings, 1x10 watts bulk head luminaires etc complete with all accessories and including connecting up with twin core twisted flexible PVC copper conduct cabe of 23/0.0076 from ceiling rose all as specified

S&F Sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 240V, 8 Ways including taking down of existing sheet metal enclosure complete all as specifide and directed.

S&F MCB single pole and neutral 6 to 32 Amps 240 Volts complete all as specified and directed.

S&F MCB SPN 240 Volts 6 to 32 Amps, 240 volts 50 Hz complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge o the plate not less1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts nuts, check nuts and washers of galvanized iron of steel all as shown in electrical plate No.3 of SSR Part - I connected to earthing test point incl necessary earth work, excavation, PCC 1:3:6 type CI using 20mm graded stone aggregate for earth chamber provn of PCC cover 40 mm thick 1:2:4 mm type B1 funnel with water Pipe, GI pipe, 15mm dia medium grade protection pipe 5 m, GI earth lead complete all as specified and directed by the Engr-in-charge.

Submain wiring with two single core PVC (FRLS) insulated flexible copper conductor cable of size 6 Sqmm and one single core PVC (FRLS) insulated unsheathed flexible copper conductor cable green colour of size 6.0 Sqmm as earth lead in and including PVC conduit medium grade with all fittings suitable for concealed type and making good the disturbed wall surfaces to match with existing specification all as required at site complete with all as specified and directed.

Sri Lakshmi Enterprises

m/s s indra reddy constructions