SPECIAL REPAIR TO OFFICERS MD ACCN BLDG NOP-13403 P13404 CAPTS MD ACCN AT LICHUBARI AND P95 01 CAPTS MD ACCN AT BHALUKMARA SPECIAL REPAIR OF FLOORING HARDSTANDING OF BLDG NOP105 MT PARK OF 15 WEU AT LICHUBARI PROVISION OF PARKING S

Amount

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4.0 Sqm each, complete all as directed.

Taking down shutters of any description exc 1.0 sqm and not exc. 2.0 sqm each, complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level), complete all as directed.

Demolition of reinforced cement concrete of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as directed.

Dismantling plain or corrugated AC sheeting any thickness or similar pattern roof covering, complete all as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as directed.

Surface excavation not exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out, complete all as specified and directed.

Excavation in trenches, not exc. 1.5 m wide and not exc. 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying pipe, cable, etc. n exc 10 sqm on plan and not exc. 1.5 m in depth and getting out in soft/ loose soil, complete all as specified and directed.

Returning filling in soft/ loose soil, including spreading, levelling, watering and well ramming in layers not exc. 25 cm, complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level not exc. 1.5 m above the starting point, complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in soft/ loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

Material and labour for, hardcore of gauge not exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick in broken stone or boulder, watered and rammed to a true surface, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:4:8) type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

Materials and labour for, plain cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

Material and labour for, RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in lintels upto1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs stone, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

Material and labour for, RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

Material and labour for providing precast cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain face and set in CM (1:4), complete all as specified and directed.

Material and labour for, brickwork with subclass ‘B’ bricks, old size, straight or curved on plan exc. 6m mean radius built in cement mortar (1:6), complete all as specified and directed.

Material and labour for, brickwork with sub class ‘B’ bricks, old size brick, straight or curved on plan to any radius in half brick thick walls built in CM (1:4), complete all as specified and directed.

Material and labour for, 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

Supply and fix for, 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); complete all as specified and directed.

Supply and fix for, 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and both faces is covered with decorative face veneer with lipping/ frame to match, complete all as specified and directed.

Supply and fix for, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as per specification & drawing.

Supply and fix for, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as per specification & drawing.

Supply and fix for, 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 200mm long, complete all as specified and directed.

Supply and fix for, aluminium handles, cast type, anodised 150mm size complete all as specified and directed.

Supply and fix for, 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

Supply and fix for, mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

Supply and fix for, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

Supply and fix in repair for, Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc, 20mm dia, complete all as specified and directed.

Supply and fix in repair for, aluminium (extruded section) door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed

Supply and fix for, sliding channels suitable for modular kitchen cabinet drawers/ tracks, side mount full extension drawer slide (2 Nos) of make HARRISON, complete all as specified and directed.

Supply and fix for, mild steel flat iron 25 x 3mm as in band, straps, hold fasts etc. and similar small articles conforming to Fe-410-0 or Fe-310-0, complete all as specified and directed. Note: The hold fast shall be treated in two coats of tar and the cost for the same is deemed to be included in unit quoted rate.

Supply and fix for, wind ties for roof including securing bolts; including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

Supply and fix for, mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

Supply and fix for, rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed.

Supply and fix for, rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-290 Gde E-165, complete all as specified and directed.

Supply and fix for, mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Supply and fix for, pressed steel frames 105 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Supply and fix for, pressed steel frames 125 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Supply and fix for, anodised aluminium powder coated (minimum thickness of powder coating 50 micron) three track sliding window and ventilator shutters two glazed shutter and one gauzed shutter without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

Supply and fix, anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply and fix for, pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Material and labour for, roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. and brushing neat cement slurry with 3.0kg of cement per sqm, complete all as specified and directed.

Material and labour for, rendering 15 mm (average) thick, cement plaster, in cement mortar (1:3), finished even and smooth without using extra cement mixed with and incuding water proofing compound as per manufactures instructions on roof surfaces and providing 3mm thick APP (Atactic Polypropylene Polymer) modified prefabricated five layers, weight not less than 3.5 Kg/ Sqm water proofing membrane, black finished reinforced with non woven polyester matt laying (weight not less than 160 gms/ Sqm) over a coat of bituminous primer @ 0.25 litre/ Sqm and two coats of bitumen based UV reflective paint with aluminium finish over APP membrane. The membrane shall be laid using butane torch and sealing all joints etc., all as specified in Para 11.44.5 of SSR Part-I, complete all as specified and directed.

Material and labour for, powder coated GI exposed snap grid frame work for false ceiling, size of grid 605 x 605mm, including GI main tee section of size 35mm x 25mm x 0.7mm (minimum), GI cross tee of size 35mm x 25mm x 0.7mm (minimum) and GI wall angle of size 25mm x 25mm x 0.7mm (minimum), suspended from soffit at approx 900mm cetnre to centre with GI cleat and steel expansion fasteners with and including level clip and 6mm dia GI wire hanging arrangement with adjuster all as specified in clause No.10.38 in SSR Part-I and incuding 4mm thick high pressure steam cured non asbestos fibre cement reinforced multipurpose board as per IS 14862 including taking down existing false ceiling system, complete all as specified and directed.

Material and labour for, 18/19 mm thick MDF board, commercial type fixed with screws to timber frame work as in lining, panelling similar location cup board shutter, shelf, kitchen cabinets etc. complete all as specified and directed.

Material and labour for, 100mm thick plain cement concrete (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in sub base floor, complete all as specified and directed.

Material and labour for, 75mm thick plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in plinth protection/ paving, finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, 100mm thick plain cement concrete (1:2:4) type B0 (using 12.5mm graded crushed stone aggregate) as in floor, laid in panel and finished the top surface even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A', complete all as specified and directed.

Material and labour for, 15mm thick wearproof topping as specified (incorporating an approved metallic floor hardner), laid on concrete floors and pavings, and finished even and smooth (except metallic hardner), complete all as specified and directed.

Supply only metallic floor hardener complete all as specified

Materials and labour for, glazed ceramic coloured tiles, 450 X 350 X 7mm/ 350 X 250 X 7mm thick, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat in cement mortar (1:4) including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.18 Sqm but not exc.0.38 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:6), including dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to stores and rubbish off the premises, complete all as specified and directed.

Material and labour for, vitrified Ceramic dark shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding in cement mortar (1:6) including dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to stores and rubbish off the premises, complete all as specified and directed.

All as per serial item No.61.00 but on vertical surfaces over and including 10mm thick backing coat in cement mortar (1:3), complete all as specified and directed.

Material and labour for granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed or bedding in cement mortar (1:6) after taking down old slab complete all as specified and directed.

Material and labour for, machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and pigment as approved laid over and including 25mm thick consolidated sand cushion and joints filled with sand, complete all as specified and directed.

Material and labour for, chequered cement concrete tiles 30cm x 30cm x 25mm thick with grey cement and pigment, set, jointed and pointed in neat cement slurry with grey cement and pigments over and including 15mm thick screed bed or bedding in cement mortar (1:4), complete all as specified and directed.

Material and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:6) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, rendering 5 mm thick, cement plaster, in cement mortar (1:3) on fair faces of concrete surfaces on ceiling, finished even and smooth without using extra cement, complete all as specified and directed.

Material and labour for, rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed. (Note: Water proofing compound shall be measured and paid seperately under relevant item).

Supply only integral water proofing compound complete all as specified.

Material and labour for, complete removal of existing treatment and applying two coats of oil bound distemper over a coat of primer including preparation of wall surfaces, complete all as specified and directed.

Material and labour for, preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat primer, complete all as specified and directed.

Material and labour for, preparation of old decorated plastered wall surfaces and applying one coat of cement base paint, complete all as specified and directed.

Supply and fix for 3.0mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sq. m in each pane, complete all as specified and directed.

Material and labour for, 4.0mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane, complete all as specified and directed.

Supply and fix for, 5.5mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane, including hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new onescomplete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated surfaces of steel and iron surfaces of any description, not otherwise described, not exc.10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed.

Material and labour for, preparation of new or previously untreated plastered wall surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of plastic enamel paint over a coat of primer over 1mm thick wall care putty, complete all as specified and directed.

Material and labour for, complete removal of existing treatment and applying two coats of plastic enamel paint over a coat of primer over 1mm thick wall care putty including preparation of plastered wall surfaces of any description, not otherwise described, over 10cm width or girth, complete all as specified and directed.

Material and labour for, complete removal of existing treatment and applying two coats of plastic enamel paint over a coat of primer over 1mm thick wall care putty including preparation of plastered on ceiling surfaces of any description, not otherwise described, over 10cm width or girth, complete all as specified and directed.

Material and labour for, complete removal of existing treatment on wall surfaces and applying two or more coats of wall finishing with Acrylic Smooth exterior paint of required shade @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm, complete all as specified and directed.

Cutting existing 40mm bore steel tubing for alterations or additions (Each cut measured), complete all as specified and directed.

Supply and fix for 15mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Supply and fix for 20mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply and fix for 20mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Supply and fix for 25mm bore tubes, 'medium grade' galvanised, with all fitting and fixed complete laid in trenches, complete all as specified and directed.

Supply, hoisting and fixing in position of rotational moulded polyethylene water storage tanks double layers (cylindrical vertical with closed top) of 1000 litres capacity with and all as specified in IS12701, specified in SSR Part I with provision of 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (Minimum weight - 210 gms), tank nipple screwed for iron pipe or brass ferrule including taking old existing unserviceable tank, complete all as specified and directed.

Supply and fix in repairs for, bib tap, fancy type, cast copper alloy, chromium plated, long body with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and directed.

Supply and fix for, two way bib tap with flange all as per Cat No.G5234A1/ T4634A1 of Parryware or as specified in PS including fittings screwed for iron pipe or for brass ferrule etc, complete all as specified and directed.

Supply and fix in repair for, pillar taps, fancy type, cast copper alloy, chromium plated, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed.

Supply and fix for, stop/ angle valves, fancy type, chromium plated, cast copper alloy with long shank and cup concealed type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore all as per Cat No.ARI 39053 of Jaquar or make specified in PS, complete all as specified and directed.

Supply and fix for, 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

Supply and fix in repair for, 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

Supply and fix for, 25mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed.

Supply and fix for, stainless steel kitchen rack wall mounted of size 24" x 36" x 10" all as per Cat No.KPR-312 of make Blue star & silver Shine Diamond or equivalent mpdel of make as specified in PS, complete all as specified and directed.

Supply and fix in repair for, sinks made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed.

Supply and fix in repairs for, vitreous china wash basin, white, flat back, size 550 x 400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

Supply and fix for, vitreous china wash hand basin of size 520mm X 450mm, white , oval shaped, counter top, including granite platform of size 90cm X 60cm, 18-20mm thick of any approved colour edges rounded or chamfered mounted on and including PVC waste pipe 32mm dia with CP waste coupling, complete all as specified and directed.

Supply and fix in repairs for, vitreous china wash down water closet pan (EWC) (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, including CP fancy type jet spray suitable for 15mm bore pipe, complete all as specified and directed.

Supply and fix in repairs for, health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply and fix in repairs for, 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and making good the disturbed floor/ surfaces, complete all as specified and directed.

Supply and fix for, PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

Supply and fix in repair for, 15mm bore dia brass CP mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.

Supply and fix in repair for, 15mm dia CP fancy type wall mixer with 'L' bend (including provision of O/H shower & hand shower) for mixing hot and cold water with hand shower HSH-1717 and tube all as per Cat No. QQT-7281 of Jaquar, screwed down for iron pipe, complete all as specified and directed.

Supply and fix for, brass chromium plated shower rose 125mm size with or without swivel joints with 225mm long arms, cast copper alloy chromium plated, fixing to 15mm steel pipe or union, all as per Cat No.OHS-1989 of Jaquar or make specified in PS, complete all as specified and directed.

Supply and fix for, toilet paper holder with flat recessed type stainless steel, complete all as specified and directed

Supply and fix in repair for, soap dish all as per Cat No.AQN-7731 of make Jaquar or equivalent model of make as specified in PS, complete all as specified and directed.

Supply and fix for, corner glass shelf assembly consisting of 5.5mm thick sheet glass shelf with chromium plated bracket guard and railing 60cm long, all as per Cat No.ACN-1173 of Jaquar make, complete all as specified and directed.

Supply and fix in repair for, brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

Supply and fix in repair for, 32mm CP brass waste coupling for kitchen sink/ wash basin including waste pipe, complete all as specified and directed.

Supply and fix in repair for, 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts, bolts etc., complete all as specified and directed.

Supply and fix in repair for, 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc. complete all as specified and directed.

Supply and fix for, 75mm bore PVC (SWR) bends any radius, complete all as specified and directed.

Supply and fix for, 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal, complete all as specified and directed.

Supply and fix in repair for, 75mm dia cast iron nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

Supply and fix for 100mm dia cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

Taking down carefully unservoceable copper/ aluminium point wiring (light, fan, bell, socket or power) including all fittings such as switches, ceiling roses, regulators, sockets, switch boxes etc. complete and making good the disturbed surfaces complete all as directed.

Material and labour for, point wiring with PVC insulated unsheathed stranded FRLSH copper conductor cable of size 1.5 Sqmm in and including PVC rigid concealed conduit (heavy duty) not less than 20mm dia with all necessary fittings and necessary cutting/ chasing etc and making good the disturbed surfaces, including 1.5 Sqmm PVC insulated unsheathed stranded FRLSH copper conductor as earth lead and connected to common earth dolly for one light point controlled by one, one way modular switch, complete all as specified and directed.

All as per serial item No.120.00 here-in-before for one 5 pin 6 Amps modular socket outlet on independent board.

All as per serial item No.120.00 here-in-before for one 5 Amps modular socket outlet on same board with other modular switch.

Material and labour for point wiring with PVC insulated unsheathed stranded FRLSH copper conductor cable of size 4.0 Sqmm in and including PVC rigid concealed conduit (heavy duty) not less than 20mm dia with all necessary fittings including 4.0 Sqmm PVC insulated unsheathed stranded FRLSH copper conductor as earth lead and connected to common earth dolly for one socket outlet 5 pin 15/16 Amps on independent board, complete all as specified and directed. Notes for item Nos. 120.00 to 123.00: Flush steel terminal box, inner plate and front plates shall be measured and paid separately under relevant item.

Supply and fix for, modular metal flush box 1/2 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 3 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 6 module, complete all as specified and directed.

Supply and fix for, modular metal flush box 8 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 2 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 3 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 6 module, complete all as specified and directed.

Supply and fix for, modular white cover plate with frame, 8 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 6A, 1 module, complete all as specified and directed.

Supply and fix for, modular switch 1 way 16A, 1 module, complete all as specified and directed.

Supply and fix for, modular socket, 6A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for, modular socket 6A/16A - 2/3 pin combined 2 module, complete all as specified and directed.

Supply and fix for, bell push, flush type, 5 Amp, complete all as specified and directed.

Supply and fix for, ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body, complete all as specified and directed.

Supply and fix for, lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

Supply and fix for, fan step regulator, 120W - 2 module, complete all as specified and directed.

Supply and fix for, sheet metal enclosure for DB's when MCBs to be used, SPN 240 volts, 8 way 200 Amps rated bus bar, metal double door type IP-43, complete all as specified and directed.

Supply and fix for, VTPN DB double door, having facility to fix MCCB in incomer and MCBs in outgoing TPN 8 way, 415 volts IP-54 protection with metal door earthing and mechanical impact strength IK 09 complete fitted with bus bars, neutral links, blanking plates all as per Cat No.507752 of make Legrand or make as specified in PS as approved including making good the disturbed surfaces, complete all as specified and directed. Note: MCCB & MCB will be measured and paid seperately under relevant item.

Supply, fixing, testing and commissioning for, 6 to 32 Amp, SP 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply, fixing, testing and commissioning for, 32 Amp, SPN 240 volts 10KA 'C' curve miniature circuit breaker (MCB), complete all as specified and directed.

Supply and fix for, sub main wiring with two runs of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, multi stranded, unsheathed, 1100 volts grade IS-694 marked drawn through and including 20mm dia rigid PVC conduit, (heavy duty) (ISI marked) surface type with all accessories such as junction boxs, bends, tees etc. including one run of single core 6.0 Sqmm (nominal area) PVC insulated copper conductor FRLSH, unsheathed stranded as continuous earth wire, complete all as specified and directed. Notes: All runs of copper conductor and one run of conduit shall be measured as one unit length.

Supply and fix for, LED tube light fitting 1 x 20W (+/-5%) 220 volt, AC with extruded strip in thermally conductive material and extruded housing in optically efficient material milky white with system lumen efficacy> 120 lumen per watt minimum system 2300 - 2400 and make LED of chip: Osram, Cree, Nichia, Seoul, Sumsung. Integrated electronic driver, SMD based LED constant current supply with double sided connection to avoid short circuit and surge protection greater than 2.5 KV, IP 20 protection and CRI>80, power factor> 0.95, THD less than 15%, correlated colour temperature (CCT) of 6500K, operating voltage of 140 to 270 volt, frequency of 50Hz, burning hours 50000 hours with comprises of CRCA pre-coated metal housing all as per Cat No. SLE BTN T8 20W of make Surya or equivalent model of make as specified in PS, complete all as specified and directed.

Supply and fix for, LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 volt AC decorative type with driver holder and LED lamp all as per Cat No.SLE BT 10 IL of make Surya or make as specified in PS, including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

Supply and fix for, LED street light fittings of 36W made of pressure die cast aluminium housing with toughened glass cover, IP66 protection, high power LEDs with secondary lenses and system efficay should be minimum 110 lumen per watt and LM79 report should be provided from NABL accredated lab all as per Cat No.SLE UL 36W IP66 LXN G1 of make Surya or make as specified in PS. Driver should be BIS approved silicon filled potted driver with inbuilt 4KV surge protection and external 10 KV surge protection inside luminaire housing of trouble free service life. THD shall be <10%, power factor>0.95, CCT5700K and brand name should be embossed/ engraved on the LED fitting for traceability till life. Warranty should be 2 years and warranty certificate should be provided on OEM letterhead at the time of delivery, complete all as specified and directed.

Material and labour for, earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.50 metre below normal ground level connected to galvanised steel earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete earth pit in PCC (1:3:6) type C1, 50mm thick pre-cast RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) cover slab (Reinforced with 8mm dia TMT bar @15cm centre to centre bothways and suitable handle made of 10mm dia), provision of funnel, wire mesh, 20mm bore galvanised steel tubing (medium grade) for watering, charcoal or coke and salt in alternate layers of 15cm (compacted thickness), 15mm bore galvanised steel tubing (light grade) for protection of earth lead connection, necessary excavation and earth work in any type of soil complete all as specified and indicated on electrical plate No.3 of SSR Part-I (2009) including testing on completion. (Note: GI earth wire and protection pipe upto 7.5metres shall be deemed to be included in the unit quoted rate).

Supply, laying, testing commissioning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm, 4 core, complete all as specified and directed.

Material and labour for, sand cushioning (dry) in trenches for protection of UG cables (below, above and around the UG cable laid in trenches) of 230mm spread thickness and consolidated (punned) upto 180mm thickness, complete all as specified and directed. (NOTE : For the purpose of payment, punned thickness of sand cushioning only shall be measured and paid for).

Material and labour for, sub class 'B' brick, well burnt, old size, flat, laid breadth-wise along the axis of cable laid in trenches over sand cushion laid for UG cable protection, complete all as specified and directed.

Supply and fix for, GI tubing 40mm bore, light grade, laid in trenches for cable protection under the road/ path/ pole, complete all as specified and directed.

A M CHOUDHURY AND CO (BID ID -3495165)

PEE BEE INDIA (BID ID -3501271)

NIHAR ENTERPRISE (BID ID -3501391)

4S ASSOCIATES (BID ID -3501360)