DAY TO DAY COMPLAINTS OF INTERNAL ELECTRIC, SOLAR WATER HEATING SYSTEM, GEYSER AND ALLIED WORKS AT NAMS

Amount

Attending of day to day electrical complaints pertaining to internal electrification received through telephone/ Armaan or in person on detailment at MES Service centre located at NAMS Area by locating and rectification of fault from and including electric meter/DB onwards in respect of sub main/point wiring including provisioning of small pieces of electric cable of size 1.5/2.5 Sqmm to 10 Sqmm single core copper conductor and length not increasing 0.50 mtrs and fixtures for power and light socket/light, fan,and bell etc complete and carrying out repairs to the extent of tightening of looseconnections,disconnection and dismantling of faulty wires, battens, conduits, boxes, main switches, MCB's, DB's and other E/M fixtures including providing necessary screws/nuts/bolts/nails for the rectification of defect and refixing of existing dismantled serviceable items and replacement of defective items with new ones at following areas with man power:- (a) At Zone-I NAMS area with one electrician + one helper (08 Hrs shift), daily (b) At Zone-II NAMS area with one electrician + one helper (08 Hrs shift) , daily (c ) At Zone-III & IV NAMS area with one electrician + one helper (08 Hrs shift), daily Note:-(i) Cost of material for the new fixtures and stores to be fixed is supplied by the contractor will be measured and paid under this Item No.1 and labour cost for the fixing/replacement of unserviceable item shall deemed to be included and cost of store replaced shall be measured as supply only against relevant Items.

(ii) Complaint pertaining to location and rectification of fault in more than one length of point wiring/sub mainwiring/DB's/fitting or fixtures etc shall be considered as an independent complaint. Similarly complaint pertaining to replacement of two fixtures in one Qtr will also be measured and paid as one complaint. (iii) Replacement of more than two fixtures/items but multiple of three fixtures or part thereof in one Qtr/Bldg will be measured as an additional complaint. (iv) In case a Qtr/room is found locked when tradesman is detailed to attend the complaint, the complaint shall be treated as one till its completion. (v) Necessary tools for tradesman shall be provided by the contractor. (vi) Transportation for tradesman and normal stores required for complaints shall be arranged by the contractor. (vii) Complaints of normal nature shall be attended and rectified within 8Hrs of receipt of complaint. However, complaints of emergent nature i.e no light, short circuit, earth fault etc shall be attended immediately on receipt of complaint round the clock.

(viii) Bldgs requiring rewiring of small qty of point wiring if ordered will be measured and paid separately under respective items below (ix) Contractor will deposit all the items to EM Store in advance and unserviceable items will be collected by the contractor as schedule of credit. (x) Electrician will report to AGE E/M complaint cell at 9 AM daily for collecting of complaints. Complaint received on Armaan Application will be done in the same day and after completion of complaint Electrician will report to Armaan Cell for uploading the completion report. (xi) Contractor deploy local electrician for the job so that urgent nature of complaint like no light, short circuit and earth fault will also done on Holidays/ Sunday.

Supply only in replacement switch piano flush type 5 Amps One-way, AC 230V on existing switch board all as specified and as directed.

Supply only in replacement of switch piano flush type 15 Amps single pole one-way, 230V complete all as specified and as directed.

Supply only in replacement switch piano type two ways AC 230 volts 6 Amps as per on existing switch board .

Supply only in replacement socket out let 2-in-1, 3 Pin 5 Amps flush type 230 volts complete all as specified and as directed.

Supply only in replacement socket outlet, flush type, 2-in-1, 3 pins, 5 & 15 Amps multipurpose complete all as specified and as directed.

Supply only in replacement switch socket combined 5/15 Amps multiperpose all as specified and directed.

Supply only in replacement bell push switch piano, flush type, 5 Amps complete all as specified and directed.

Supply only in replacement of bell ding-dong 230 volts, single phase complete all as specified and directed.

Supply only in replacement of ceiling rose 65x50mm two to three terminals AC 230 volts complete all as specified and directed of any make/model as per in existing building.

Supply only in replacement rotor type Bipin holder of any size/shape as required at site for 20/28/40 watts tube light 240 Volts complete all as specified and directed.

Supply only in replacement batten type angular/ Batten lamp holder insulated body with back plate suitable for batten fitting including PVC round block complete all as specifed and directed.

S&F in replacement MCBs single pole (SP) 5 to 32 Amps with 10 KA breaking capacity of 'C' series in distribution boards all as specified.

S&F in replacement MCBs single pole and neutral (SPN) 32 Amps with 10 KA breaking capacity of 'C' series in distribution boards all as specified and directed.

S&F in replacement MCBs single pole and neutral (SPN) 40 to 63 Amps with 10 KA breaking capacity of 'C' series in distribution boards all as specified and directed.

Supply only in replacement of single pole and neutral sheet metal enclosures with two pin & earth plug and socket complete with one single pole MCB of 20 Amps complete all as specified and directed.

Supply only in replacement plug top 3 pin, 5 Amps complete all as specified and directed.

Supply only in replacement plug top 3 pin, 15 Amps complete all as specified and directed.

S&F in replacement Electronic Ballast (P.F 0.9), 230v, 50HZ, 36 watt complete all as specified and directed.

S&F in replacement fluorescent tube light rod 4 feet long of capacity 36 watt all as specified and directed by Engr-in-Charge.

S & F in replacement LED bulb of capacity 5 watts complete with all accessories base (ISI marked) all as specified and directed by Engr-in-Charge.

S & F in replacement LED bulb of capacity 7 watts complete with all accessories base (ISI marked) all as specified and directed by Engr-in-Charge.

S&F in replacement LED bulb of capacity 9 watts complete with all accessories base (ISI marked) all as specified and directed by Engr-in-Charge.

S&F in replacement LED bulb of capacity 12 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in replacement LED bulb of capacity 15 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S & F in replacement LED Tube rod with polycarbonate diffuser 4 feet long of capacity 18 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in replacement LED Tube rod with polycarbonate diffuser4 feet long of capacity 20 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

S&F in replacement LED Tube rod with polycarbonate diffuser4 feet long of capacity 20/22 watts complete with all accessories base (ISI marked) all as specified & directed by Engr-in-Charge.

Supply only in replacement of LED 12 Watt Square/ Round surface mounted LED Panel down lighter complete all as specified and directed.

Supplying only in replacement LED bulk head light fittings including led lamp 10 watt as per IP65 and making necessary connections complete all as specified and directed.

Supply only in replacement LED slim panel cygnus series recess/surface/suspended mounting LED slim ceiling light 2'x2' with extruded aluminium housing and milky diffuser, suitable for recess mounted size 595x595mm complete with LED tube.

Supply only in replacement of 6 Watt Round recess mounted down lighter separate replaceable electronic driver celling cut out dia 105 mm height 16 mm round shaped polycarbonate fixture complete all as specified and directed.

Supply only in replacement of 12 Watt Round recess mounted down lighter separate replaceable electronic driver celling cut out dia 160 mm height 16mm round shaped polycarbonate fixture complete all as specified and directed.

Supply only in replacement of 6 Watt Square recess mounted down lighter separate replaceable electronic driver celling cut out 104mm x 104mm height 30mm square shaped polycarbonate fixture complete all as specified and directed.

Supply only in replacement of 15 watt Square recess mounted down lighter separate replaceable electronic driver celling cut out 155mm x 155mm height 32mm square shaped polycarbonate fixture complete all as specified and directed.

Supply only in replacemnt box type PVC rectangular block for mounting switches, sockets, fan regulator etc 4 / 6 way, surface mounting complete all as specified and directed.

Supply only in replacement of frame plate for modular switch 4 module including screws and washers etc model/make as per existing in site complete all as specified and directed.

Supply only in replacement of frame plate for modular switch 8 module including screws and washers etc model/make as per existing in site complete all as specified and directed.

Supply only in replacement modular ceiling fan regulator, electronic Socket type, single phase, 230 volts complete all as specified and directed.

Supply only in replacement ceiling fan regulator, electronic switch type, single phase, 230 volts complete all as specified and directed.

Supply only in replacement MS machine screw 25 mm long suitable for fixing bakelite hylum sheets / square blocks complete all as specified and directed .

Supply only in replacement MS Housing box 5 / 6 module suitable for modular switch as per existing including taking out old UNSV switch box and making good to the disturb surface by PCC (1:2:4) complete all as specified and directed.

Supply only in replacement of MCCB 100 amps 4 pole, AC 415 volts 25 KA, four pole including making connections with suitable size of aluminium lugs of any make /Model as per Existing MCCB Fitted in DB. all as specified and directed.

Supply only in replacement of modular switch 6 Amps one module 230 volts AC as per existing model/make complete all as specified and directed

Supply only in replacement of modular switch 16 Amps one module 230 volts AC as per existing model/make complete all as specified and directed

Supply only in replacement of modular socket, 5/6A -2/3 pin combined 2 module, 230 volts AC as per existing model/make complete all as specified and directed.

Supply only in replacement of modular socket, 15/16A -2/3 pin combined 2 module, 230 volts AC as per existing model/make complete all as specified and directed .

Supply only in replacement modular fan regulator, 2 Module/1 module , 4 step heavy duty 230 volts as per existing model/make complete all as specified and directed.

Supply only in replacement of capacitor AC 230 volts 2.25 MFD

Supply only in replacement of capacitor AC 230 volts 3.15 MFD

Supply only in replacement of 3 mm thick hylum sheet of any size including screws and washers etc as per required at site complete all as specified and directed.

Supply only in replacement moduler bell push switch piano, flush type, 6 Amps complete all as specified and directed.

Supply only in replacement of 12 Watt Square recess mounted down lighter separate replaceable electronic driver celling cut out dia 160 mm height 16mm round shaped polycarbonate fixture complete all as specified and directed.

Supply only in replacement toggle switch for amination depot complete all as specified and directed.

S & F in replacement LED tube light fitting , 1 x 20 W, 230 V Energy efficient T8, Box type made of CRCA sheet heavy duty industrial type housing with reflector cover channel, bipin holders, connector block, etc. complete with tube rod LED 20 watt, all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size.

S & F in LED mirror fitting. 1 x 8 W, 230 V Energy efficient , Box type, housing with reflector cover channel, bipin holders, connector block, etc. complete with tube rod LED 8 watt, all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and fixing bed light fancy type,10 watt with lamp complete all as specified and directed.

Supply only in replacement of single core wire 2.5 Sqmm multi-strand PVC insulated copper conductor FRLS cable including connections of cable with MCBs or bus bar complete all as specified and directed.

Supply only in replacement of single core wire 1.5 Sqmm multi-strand PVC insulated copper conductor FRLS cable including connections of cable with MCBs or bus bars complete all as specified and directed.

Material and labour for point wiring with 1.5 Sqmm multi strand pvc insulated copper conductor cable in existing concealed conduit for one light or bell point controlled by one switch including pvc insulated 1.5 sqmm copper conductor continuous earth wire using existing CI/MS sunken box and connecting earth with dolly complete all as specified and directed. ( Note : Switch, socket measured as separate item )

All as per item No 61 here in before but for one 5 Amps independent board complete all as specified and directed.

All as per srl item No. 61 here in before but for one 5 amps socket out but on the same board complete all as specified and directed.

Matrial and labour for point wiring with 2.5 sqmm multi strand pvc insulated copper conductor cable in existing concealed conduit for one 15 amps socket outlet independent controlled by one switch including pvc insulated 2.5 sqmm copper conductor continuous earth wire connecting earth with dolly complete all as specified and directed.

Supply & fix in replacement of building security LED Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens complete all as specified and directed.

Supply and fix in repair GI pipe bracket ,made out of GI pipe 50mm dia light grade 1.2mtr long bend to the shape 120 degrees angle complete with two nos of clamps for fixing on walls complete all as specified and directed.

Supply & fixing in replacement of integral post top lantern complete with black ABC plastic spigot, spun aluminium funnel shape with clear acrylic cover light opening on canopy with baffles and accessories and suitable for LED lamp complete all as specified and directed

M& labour in replacelment for service wire10 sqmm 2core pvc insulated and pvc sheathested 1100 volts grade all as specified and directed

M&L for taking down the existing faulty single phase tamper proof Electronic Energy meter with LCD display 230 volts 4 wire system, 10-60 amps, 50 Hz ,replacing the unserviceable chip board, unsv body and all burnt parts complete,making it to serviceable state, including testing, caliberation & refixing the same complete all as specified and directed by Engr-in-Charge.

Attending complaints for taking down geysers of any make & size from existing position of any height for repair, mainteance and refixing the same after neccesary repair complete all as directed. Notes (i) The defective parts to be replaced shall be measured and paid separately under relevant item of Sch . (ii) Cost of minor items i.e. Screws, nut & bolts etc shall be deemed to be included in the above item.

S & F in replacement heavy duty PVC connection pipe (hot type) 15 mm bore size with PTMT nuts,rubber washers etc complete of length 450 mm long complete all as specified.

S & F in replacement PVC connection pipe 15 mm bore size with PTMT nuts,rubber washers etc complete of length 600 mm long complete all as specified.

S & F in replacement geyser element 2.0 KW, ISI marked with gasket, nuts, bolts suitable for the existing triangular/round shape/make of the geyser under repair complete all as specified.

S & F in replacement geyser element 1.5 KW, ISI marked with gasket, nuts, bolts suitable for the existing triangular/round shape/make of the geyser under repair complete all as specified.

S&F in replacement thermostat (ISI marked) suitable for existing make of the geyser under repair of cap 50 / 25 Ltrs complete all as specified.

S&F in replacement geyser safety valve (pressure release valve) for the exsiting make & capacity of geyser complete all as specified.

M&L for painting of geysers of any cap 25/50 Ltr with 2 coats of synthetic enamelled paint after scraping the existing old painted surface complete all as directed.

S&F in replacement shyphon assembly suitable for 50 ltr geysers of any make, any type complete all as specified and as directed by Engr -in-Charge.

S&F in replacement shyphon assembly suitable for 25 ltr geysers of any make, any type complete all as specified and as directed by Engr -in-Charge.

S&F in replacement inner tank made up of stainless steel conforming to IS suitable for 25 /35 ltr gyser vertical type including rubber gasket complete all as specified and directed.

S&F in replacement inner tank made up of stainless steel conforming to IS suitable for 50 ltr gyser vertical type including rubber gasket complete all as specified and directed.

S&F in replacement outer body made up of steel duly painted including base cover and indicator assembly suitable for 50 ltr gyser complete all as specified and directed.

S&F in replacement outer body made up of steel duly painted including base cover and indicator assembly suitable for 25 ltr gyser complete all as specified and directed.

S&F in replacement 3 Core PVC insulated PVC sheathed flexible copper wire multistranded of size 2.5 sqmm complete all as specified and directed.

Supply & fix in replacement indicator lamp any type/size 230 Volts complete all as specified and directed.

Supply & fix in replacement of brass non-return valve 15 mm dia horizontal/verticle type ISI marked complete all as specified and as directed.

Supply and fixing in replacement of metal clad plug top 20 Amps complete,all as specified and directed.

Supply and fixing in replacement of metal clad socket 20 Amps complete,all as specified and directed.

Repair to hot water storage tank of solar water heating system including detecting the leakage, cleaning of inner tank, bracing to leakage portion testing for leakage etc for any type, capacity of solar water heating hot water tank including removing, diamantling, assembling refixing and making water and electric connections complete,all as specified and directed.

Supply and fix in replacement of heating elements for solar water heating system 5 KW with rubber gasket for any type of geyser

Supply and fix in replacement of solar water steel tank cap 500 to 750 ltrs complete all as specified and directed.

Supply and fix in replacement of solar water steel tank cap 300 to 400 ltrs complete all as specified and directed.

Supply and fix in replacement of Syntex tank cap 1000 ltrs complete all as specified and directed.

Supply and fix in replacement of Syntex tank cap 500 ltrs complete all as specified and directed.

Supply and fix in replacement of GI Pipe medium grade with insulation dia 20 mm complete all as specified and directed.

Supply and fix in replacement of GI Pipe medium grade dia 20 mm complete all as specified and directed.

Supply and fix in replacement thermostat for Solar water heater, AC, SP 220 volts including making necessary connection, ISI marked, complete all as specified and as directed.

Supply and fix in replacement of temparature gauge for water heating system ISI marked, complete all as specified and as directed.

Material and labour in replacement of solar glass panel complete all as specified and directed including collant quiet, absorbing plates , flow tube , insulation coolant outlet certificate for transmissibly will be provided from approved company complete all a specified and directed.

Supply and fixing in replacement of automatic monoblock pressure/booster pump size 25 mm x25 mm, tech motor S1 class B 230 Volts 500 Hz, RPM 2800, 10 MF, Input power 650 watt with pressure tank of cap 19 Ltrs PS max pressure bar 10 PT test pressure bar 14 with complete accessories incl GI pipe/gate valve/NRV complete all as specified and directed.

M&L for replacement of geyser assembly including heating element , relay , thermostat etc complete suitable for 25 ltr cap geysers as per existing make Complete all as specified and as directed by Engr-in-Charge.

KARACHI ELECTRIC & TRADING CO.

M/s AKG Engineers & Contractors

Bharat Builder