PROVN OF OVERHEAD SHED FOR STORAGE OIL LUB AND FOL ITEMS,RECEPTION CENTRE FOR CMP AT GATE NO. 1, TOILET BLOCK AT TOWER COLONY, ELEVATED WATCH TOWER, SPECIAL REPAIRS TO TOILETS AND SEWAGE LINE AND FLY PROOFING DOORS IN JCOS/ORS MD ACCN AT NASIRABAD

Amount

Excavation in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes etc not exc 10 Sqm on plan and getting out in soft/loose soil, complete, all as specified & directed.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil, complete, all as specified & directed.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point, complete, all as specified & directed.

M&L for PCC 1:4:8, type D2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete, all as specified & directed.

M&L for PCC 1:3:6, type C2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete, complete, all as specified & directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete.

S&F mild steel framed work using ERW or induction butt welded tubes conforming to I.S 1161-1979 Grade St-240 including necessary welding, bolting, special shaped washer, clamps, cleats etc., complete all as specified & directed.

M&L for mild steel work as in wind ties for roof covering including securing bolts etc. including all necessary drilling, bolting or riveting etc and similar work conforming to Grade E-165 (Fe 290) , complete, all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5 cm long and dia of neck 11 to 15 mm, complete, all as specified & directed.

S&F 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet "colour" having tensile strength of 550Mpa as in roof covering /cladding to wall, fixed with self tapping screws and bituminous washers, complete, all as specified and as directed. Make :- Durashine of Tata Blue Scope and Dura Steel of Everest.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet for ridges of 0.50mm thick of an colour having tensile strength of 550 MPs as in roof covering/claddingto wall, fixed with self tapping screws, complete all as specified & directed. Make :- Durashine of Tata Blue Scope and Dura Steel of Everest.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer, complete, all as specified & directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6, complete, all as specified & directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls , built in cement mortar 1:4, complete all as specified & directed.

M&L for 40mm thick PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in damp proof course on horizontal surface using water proofing compound including necessary formwork complete all as specified & directed. . Note : - Water proofing compound shall be measured and paid for separately.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface, complete, all as specified & directed.

M&L for 75 mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection, surface finished fair and even, complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 2 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:1).

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 over and including 25 mm thick sub base of PCC 1:2:4, type B1 using 20mm graded crushed stone aggregate, complete, all as specified and directed.

All as per description of serial item No. 18 above but as in skirting on and including 10 mm thick screed plaster backing in cement plaster 1:4, finished even and fair to receive tiles, complete all as specified and directed.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete, all as specified & directed.

All as per description of serial item No. 20 here-in-before but 8mm dia bar.

All as per description of serial item No. 20 here-in-before but 6 to 10mm dia in stirrups, spacers and binders.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like, complete, all as specified & directed. .

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete, complete, all as specified & directed.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like, complete, all as specified & directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete, complete, all as specified & directed.

M&L for reinforced cement concrete M-25 (Design Mix) using 20mm graded crushed stone aggregate in lintels over 1.5m clear span, seismic and other similar bands, lintel bands, plinth bands, roof bands and the like, complete, all as specified & directed.

Formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete, complete, all as specified & directed.

M&L for reinforced cement concrete M-25 grade (Design mix) using 20mm graded crushed stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like, complete, all as specified & directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete, complete, all as specified & directed.

M&L for 20mm thick black granite slab of approved shade, as in kitchen platform etc, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing as per local trade practice, complete, all as specified & directed.

M&L for 15mm thick rendering in two layer on stone masonry surfaces or surfaces other than fair face of brick work of walls consisting of 1st layer of 10mm thick plaster in CM 1:6 and 2nd layer (setting coat or top layer) of 5 mm thick plaster in CM 1:4 mixed with water proofing compound (ISI marked) @ 3% by weight of cement or as per manufacturer’s instructions, finished fair & even, complete, all as specified and directed. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for rendering 10mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete, complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of ceilings & applying three coats of white wash, complete, all as specified & directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1 mm thick finished coat of white wall care putty, complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint, complete, all as specified & directed.

Aluminium door shutter with frame of aluminium section including necessary joining cleats, glazing clips, rubber neoprene packing, brass handle and brass tower bolts of size 150mm x 02 Nos in each door, hinges, anodised aluminium snap beading screws, hydraulically regulated double action floor door spring made up of 1.25 mm thick aluminium alloy sheet foundation box for each shutter, etc and including fitted with 5mm thick tinned glass in glazed shutter with brass mortice lock 100 mm, 2 levers, verticle type, complete, all as specified & directed.

Aluminium window/ventilator shutter with frame, sliding/side hung type with sash bars including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc and including in each window fitted with 5mm thick tinned glass in glazed shutter, duco pattern aluminium, anodised grill (weight not less than 2.625 Kg/Sqm) and stainless wire cloth 0.36 mm nominal dia and average width of aperture 1.40mm in gauzed shutter etc, complete, all as specified & directed.

M&L for rendering 10mm thick in cement mortar 1:4 on roof top surfaces, mixed with water proofing compound as per manufacturer's instruction, finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for APP modified polymeric water proofing membrane, 2 mm thick having centre core not less than 100 micron high molecular high density polythelene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3 Kg/Sqm applied with bonding material using blown type bitumen conforming to IS-702 grade 85/25 @ 1.2 Kg/Sqm over bitumen primer conforming to IS-3384 @ 0.40 Kg/Sqm with final coat of bonding bitumen grade 85/25 @ 1.2 Kg/Sqm over APP membrane with all overlaps, complete, all as specified & directed.

M&L for 40mm thick (average consolidated thickness) type B0 using 12.5mm graded stone aggregate as in padding even and smooth without using extra cement with existing slope with 'V' shaped grooves 6mm wide and 10mm deep @ 1.2m interval or part thereof, both ways on top of padding and filled with mastic bitumen of 1:1 proportion, complete, all as specified & directed.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete, all as directed.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of walls & applying three coats of white wash, complete, all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

M&L for glazed ceramic tiles (coloured) 450mm x 300mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete, all as specified and directed.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 ,complete, all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified & directed. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 2 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:1).

Demolition of plain cement concrete in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description, complete, all as specified & directed.

S&F brass chromium plated shower rose 125 mm size with swivel joint including fixing to steel pipe of 15mm bore or union, complete, all as specified & directed.

S&F in repairs brass chromium plated shower rose 125 mm size with swivel joint including fixing to steel pipe of 15mm bore or union complete, all as specified & directed.

All as per serial item No. 54 here-in-above but fixed in repairs.

S&F soap dish holder (Cat Part No ACN-1131N of make - Jaquar or equivalent of Marc/Parryware/Somany/Parko/Gem/Prayag) complete all as specified & as directed.

All as per serial item No. 56 here-in-above but fixed in repairs.

S&F tubular towel rail, aluminium anodized, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete, all as specified & directed.

All as per serial item No. 58 here-in-above but fixed in repairs.

S&F 15mm bore Stop valve, fancy type with long shank and cup (concealed type) of cast copper alloy chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union, complete, all as specified & directed.

All as per serial item No. 60 here-in-above but fixed in repairs.

S&F 15 mm bore bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete, all as specified & directed.

All as per serial item No. 62 here-in-above but fixed in repairs.

S&F in repairs 15mm bore angle stop valve fancy type of cast copper alloy chromium plated screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union, complete, all as specified & directed.

S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides, complete, all as specified & directed.

All as per serial item No. 65 here-in-above but fixed in repairs.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors, complete, all as specified & directed.

All as per serial item No. 67 here-in-above but of 20mm bore pipe.

All as per serial item No. 67 here-in-above but of 25mm bore pipe.

S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) of 500 litre capacity, double layered, hoisted and fixed in position including disconnecting & taking down the existing water tank, complete, all as specified in SSR Part - I and as directed. Note :- (i) The unit rate quoted by tenderer shall be deemed to insulate water tank with GI pipe medium grade 10cm long projected inside and outside of tank with bore suitable for inlet and outlet, GI pipe 20mm bore medium grade projecting 10cm inside and outside of the tank for over flow, GI pipe 20mm bore medium grade projected 10cm inside and outside of tank for vent & mosquito cover for vent/overflow pipe.

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts & making good disturbed surfaces with existing finishes, complete, all as specified & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement, complete, all as specified & directed.

S&F mild steel framed work as in doors / gates / steel frames / chowkats etc. of angle or other section with gusset plates, rails, braces, etc., complete conforming to Grade E-165 (Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position, complete, all as specified & directed.

S&F extruded aluminium alloy handle, 150mm size, fabricated type, anodized (ISI marked), complete, all as specified & directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked), complete, all as specified & directed.

S&F butt hinges of size 100mm extruded aluminium alloy with galvanized mild steel hinge pin, anodized type B-21, complete, all as specified.

S&F vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc and, making good to floor, complete all as specified & directed.

All as per serial item No. 77 here-in-above but fixed in repairs.

S&F PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle, complete, all as specified & directed.

All as per serial item No. 79 here-in-above but fixed in repairs.

S&F vitreous china wash hand basin, white, flat back of size 550mm x 400mm with including 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete, all as specified & directed.

All as per serial item No. 81 here-in-above but fixed in repairs.

S&F in repairs 15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes, complete, all as specified & directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted stone masonry built in cement mortar 1:6 complete all as specified & as directed.

All as per serial item No. 85 here-in-above but except stones. Note : Old serviceable stones retrieved from demolition shall be used under this item.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses, hammer dressing with maximum depression on face from straight edge held against the dressed surface not exc 20mm, lime or sand stone, complete, all as specified & directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., complete, all as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors or fixed to walls with MS stack clamps of FI 50x3 mm including fittings complete all as specified & directed. Note :- Excavation & earthwork shall be measured & paid for separately.

All as per description of serial item No. 89 above but 75mm bore pipe.

S&F 110 mm bore PVC (SWR) junction single (single ‘T’), equal or unequal with oval access door complete all as specified & directed.

S&F 110mm bore PVC (SWR bend, any radius with access doo complete all as specified & directed.

S&F 75mm bore PVC (SWR) bend, any radius with access door complete all as specified & directed.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified & directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified & directed.

S&F in repairs PVC (SWR) Gully trap 125/110mm, setting and jointing with solvent cement, complete, all as specified & directed.

M&L for cement concrete (1:3:6) type C1 using 20 mm graded crushed stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement. Note : Forming fair finished channel for drain using extra cement shall be measured and paid for separately.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc.

Dismantling of stone slabs of any description or thickness n cover slab etc., complete, all as directed.

M&L for 40 mm thick rough dressed sand stone slabas in cover slab, bedded and jointed in cement mortar 1:4, complete all as specified & as directed.

Demolition and breaking up 100mm bore pipe drain pipes, salt glazed stone ware, AC or reinforced concretepipe, set in cement mortar including PCC haunching and bedding, complete, all as directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe, complete, all as specified and directed.

S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested, complete, all as specified & directed.

M&L for construction of Septic tank for 50 users, excavation in any type of soil, foundation in PCC 1:2:4, type B2, brick work in CM 1:4, RCC slab in RCC 1:2:4, type B1, precast RCC manhole cover having 6 mm thick plate embedded all around/fibre reinforced cover with angle iron frame vent shaft and sludge chambers etc, complete all as specified and shown in drg No. CEBZ/TD/76/2011, Sheet 1 & 2 and as directed by Engr-In-Charge.

M&L for construction of soakage well of size 1.8 m dia and 3.0 metre deep, excavation in any type of soil, foundation in PCC 1:3:6, type C2, honey comb and solid brick work in CM 1:4, RCC slab in RCC 1:2:4, type B1, filling with brick bats, RCC cover slab in M-25 (Design mix) complete, all as specified and shown in drg No. CEBZ/TD/78/2011, Sheet 1 & 2 and as directed by Engr-In-Charge.

Surface dressing not exc 15cm deep in soft/loose soil complete all as specified & directed.

M&L for rolled mild steel work in stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. complete, all as specified & directed.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement, complete, all as specified & directed.

M&L for 100 mm thick PCC (1:4:8), type D2 using 40 mm graded crushed stone aggregate as in sub base of floor, surface finished fair and even,complete, all as specified & directed.

M&L for 100 mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in floor, top surface finished fair & even (PCC shall be laid in alternate bays in panels of size not exc 2m x 2m or as directed), complete, all as specified and directed.

M&L for 50mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in flooring, finished even and smooth without using extra cement, complete, all as specified & directed.

Earth filling under floors including spreading, leveling, watering and well ramming in layers not exc 25 cm thick, complete, all as specified & directed. Note :- Soil obtained from excavation under serial item No. 1 here-in-before shall be used for filling under floors.

Formwork to edges of concrete flats, roofs, floors etc and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces, complete, all as specified & directed.

S&F vitreous china urinal, flat back, half stall type, white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia, complete, all as specified & directed.

S&F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms), complete, all as directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed on wall with PVC rawl plug & cadmium plated brass screws, complete, all as specified & directed.

S&F factory made steel ventilator factory made made out of MS hollow section 79 mm x39 mm x 1.6 mm thick frame with double shutter (glazed & wire gauzed shutter) made out of 'Z' section using flush butt welding and tennon riveting, all as per IS 1038/83, dobby hinges shall be provided to both shutters, locking arrangements, 25mm aluminium knobs to shutter, aluminium hook & eye, 10mm MS square bars in grill, 04 Nos lugs welded to frame 'Z' section handle, 100 mm including necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4, type B1 including two coat of synthetic enamel paint over a coat of zinc crome/red oxide primer, complete, all as specified & directed. Note:- Wire mesh and sheet glass shall be measured and paid separately. with top hung shutter including hinges, steel peg stay, handle complete all as specified.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications complete all as specified & directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete, all as specified & directed.

Supply and fixing stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete, all as specified & directed.

S&F butt hinges of size 100 mm medium weight, cold rolled mild steel ISI marked, complete, all as specified & directed.

Supply only integral water proofing compound (ISI marked).

S&F in repairs PVC (SWR) floor trap plain with PTMT grating including jointing with solvent cement, diameter of outlet 75mm, complete, all as specified & directed.

S&F rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) of 1000 litre capacity, triple layered, hoisted and fixed in position, complete, all as specified in SSR Part - I and as directed. Note :- (i) The unit rate quoted by tenderer shall be deemed to insulate water tank with GI pipe medium grade 10 cm long projected inside and outside of tank with bore suitable for inlet and outlet, GI pipe 20mm bore medium grade projecting 10cm inside and outside of the tank for over flow, GI pipe 20mm bore medium grade projected 10cm inside and outside of tank for vent & mosquito cover for vent/overflow pipe.

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms), complete, all as specified and directed.

M&L for 40 mm thick sand stone slab, set and jointed over joist etc. in cement mortar 1:4 as in base of water tank including 25 mm thick PCC 1:2:4, type B0 using 12.5 mm crushed stone aggregates), finished surface even and smooth without using extra cement, complete, all as specified & directed.

M&L for 75 mm thick PCC (1:3:6) type C2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even, complete, all as specified & directed.

M&L for factory made chequered cement concrete tiles, 25cm x 25cm x 22mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & no pigment, over & including 20mm thick screed bed in cement & sand mortar 1:4, complete, all as specified & directed.

S&F 20mm bore gun metal gate valve with iron wheel head, screwed both ends for iron pipecomplete, all as specified & directed. .

S&F factory made 35mm thick glazed and skeleton shutters (three panels) made of second class hard wood, open rebated and prepared to receive glass, gauze etc (witht sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete, all as specified & directed.

S&F butt hinges of size 125 mm medium weight, cold rolled mild steel ISI marked complete all as specified.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer, complete, all as specified & directed.

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) & refixing in the same opening including cutting holes for hold fasts & making good disturbed surfaces with existing finishes complete all as directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20 mm dia or higher complete with all PVC conduit accessories and sunk type anodised terminal box thick with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories for:-

One light point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board.

All as per item No.134 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth complete all as directed.

S&F switch piano flush type 5 Amps, single pole one way complete all as directed.

S&F switch piano flush type 15 Amps, single pole one way complete all as directed.

S&F Socket outlet, 3 Pin 5/6 Amp, flush type complete all as directed.

S&F socket out let 2 in 1, 6 pin, 5/6 & 15/16 Amp multipurpose, flush type complete all as directed.

S&F ceiling fan regulator electronic flush , steped (four step) 230 Volts, AC complete all as directed.

S&F ceiling rose surface bakelite, 3 terminals 63.5 x 17 mm complete all as directed.

S&F LED tube light fitting in acrylic linear tube (1x 18 watt), 230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders, LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. Make: Bajaj Cat Part No BLRB 18W CW (tube) & BLRB-DB 118(batten)/ Havells Cat part No LHLDDBXEUL7Z018 (tube) & LHFYBWP1TB1W020 (batten)/Syska Cat part No SSK -T8-18W (tube) & SSK-TL-22 F (batten)

S&F of lamp holder PVC/polycarbonate type with back plate including LED lamp 9/11 watt complete all as specified and directed.

S&F energy saving street light luminaire 15 watt LED , pressure die cast housing with high power LED as lighting source and lence embedded , polycarbonate diffuser, IP 66 protection including connecting with three core copper flexible wire from ceiling rose to connector of light fitting, complete with street light bracket made of 32 mm GI pipe , 1.2 mtr lenght with clamp, nut and bolts complete all as specified and directed. Make : Havells Cat Part No. ENDURAPEARLSL15WLED757SASYTOPC or equivalent from other specified makes in Appendix of PS.

S&F ceiling fan of 1200 mm sweep, 230 Volts, AC 50 Hz, copper winded, high speed, BEE star rated as per latest norms with motor, blades (03 Nos), down rod, canopy & shackle assembly including 0.5 sq mm three core PVC insulated flexible wire with mulitstranded copper conductor from ceiling rose to connector of ceiling fan and writing of MES No, complete, all as specified and directed by Engr-in-Charge. Make: Havells ES 50 or equivalent from Crompton/ Usha/Orient as approved by the GE.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 4 way, 415 volts suitable for housing MCB's complete, all as specified and directed. Note: MCB DB and MCBs shall be of same make.

S & F of MCB SPN, 240 volt, 25 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F of MCB SP, 240 volt, 6 to 32 Amp capacity, 10 KA , 'C' curve complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh, PCC chamber in cement concrete 1:3:6 type C-2 and RCC 1:2:4 type B1 cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing, complete, all as specified & directed.

supply and installation evoporative type desert cooler, single phase, 230 Volt, steel body made out of sheet metal not less than 20 SWG, water storage capacity not less than 40 litre, nominal air flow capacity of 4000 Cum per hour, complete, all as specified & directed. Make of Motor: Khaitan/Symphony/Bajaj/Kenstar

Supply, laying & testing of LT cable, 1100 volt grade, heavy duty of size 10 Sq mm, 2core with PVC insulated aluminium stranded conductor with an inner sheathing of PVC tape, armoured with galvanised steel wire or tape and over all PVC sheathed, complete all as specified and directed

Supply and laying dry river sand for cable cushioning in trenches to required width at bottom and top cable including spreading, levelling, watering and consolidation complete all as specified and directed by Engineer-in-charge. Note: Punned thickness only shall be measured and paid.

Supply and laying of bricks of old class ‘B’ as protection cover to UG cable, laid flat adjoining to each other width wise, complete, all as specified.

Supply and laying GI tubing 40 mm bore, light grade with all fittings, laid in trenches/under floor or fixed on pole/on wall for cable protection complete all as directed.

M&L for Boaring of hole under black top road/foot path in soil for laying of GI tubing 40 mm dia for passing of electric cable, including making good damaged surfaces, complete, all as specified and directed.

M&L for LED flood light luminaire of 120 W with secondary optics made in pressure die cast aluminium housing with toughened glass and high power LEDs and secondary lenses with IP 66 protection, lumen efficinacy > 110 LPW Option for 3000K 10KV SPD included with all fixing arangement, nuts, bolts and washer connecting to electric system with 1.5 mm PVC Aluminium stranded conductor 2 core of required length from light fitting to street light control box on pole, testing on completion, complete all as specified and directed Make: Crompton LFLN-120-CDL/60-M or equivalent from other specified in PS Appendix.

S&F LED mirror light fitting, 10 Watt, complete, all as directed by Engr-In-Charge.

S&F Exhaust fan, metal body, 300mm sweep, suitable for 230 Volt, SP, 50 Hz including louvers, complete, all as specified & directed. Make: Havells, Model: Ventil Air DS or equivalent from Bajaj/Khaitan.

PD GUPTA AND COMPANY

M/S MAKHIJA TRADERS