PROVN OF TRAILOR STANDING PLINTH AT MT GARAGE FOR ASC AND PROVN OF SPECIAL REPAIR TO BLDG NO P 106 AT MIL STN BIKANER

Amount

Demolition of reinforced cement concrete to any thickness as in slabs, beams incl cutting of reinforcement as reqd at site.

Dismantling of Roof tiles of any description or thickness in floor, apron etc laid, bedded and pointed in cement mortar complete all as specified & directed by Engr-in-charge.

Demolition of lime Concrete of any description over roof slab complete all as specified & directed

Demolition of cement concrete incl tiling/Kota stone in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.

Taking down Wall panelling and similar work and removing to store as per directed by engineer in charge

Dismantling of existing false ceiling of ac sheet etc complete all as specified.

Demolition of RCC in column, beams complete all as specified.

Taking down cement plaster, any description on brick or stone or cement concrete walls including any tiles and raking out joints, hacking for key, scrubbing down with water complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), all as specified and directed by Engineer-in Charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), all as specified and directed by Engineer-in Charge.

Taking down door shutter of any desc exc 1 sqm but not exc 2 sqm and refixing in the same opening after easing, adjustment complete all as specified and directed.

Taking down Shutters/Frames of any description n exc 1 sq.m each

Demolition of brick/stone masonry built in CM. all as specified and directed by Engineer in charge.

Taking up or down steel tubing 15 mm bore with connections for cleaning for refixing or removing to store yard complete all as specified

Taking up or down steel tubing 20 mm bore with connections for cleaning for refixing or removing to store yard complete all as specified

Dismantling cast iron /PVC/AC pipes fixed to walls or laid in trenches in any position.

Dismantling water tanks and removing to store exc 250 ltrs and nexc 500 ltrs

M&L brick work with fly ash bricks straight or curved on plan to any radius built in CM 1:6 all as specified.

M&L half brick work with fly Ash bricks straight or curved on plan to any radius built in CM 1:4 all as specified and directed.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete all as specified.

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 laying floor finishes complete all as specified.

M&L for 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:3 and finished even and fair for receiving tiles on vetical surface mplete all as specified.

M&L for Rendering 10+5 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately).

M&L for Rendering 10mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement all as specified.

M&L for Rendering 5mm thick on brick or concrete surface as in ceiling in cement mortar 1:3 finished even and smooth without using extra cement all as specified.

M&L for glazed coloured ceramic tiles in dado/vertical surface (300mm x600mm x 7 mm/450x300x7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specified and directed.

M&L for Non skid coloured tiles (square/rectengular) 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for machine cut kota stone 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

Moulding of kota /marble stone full round complete all as specified.

M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types as in platform & color Complete all as specified and directed by Engr-in-charge

M&L for vitrified ceramic tiles 10 mm thick (squares/rectangular) area of each tile not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of existing surfaces. (Note : The contractor shall have no claim on diffrence what so ever on shade/colour of tiles)

Ditto- same all as per Srl item No above but as in Skirting/Dados.

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

M&L for TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

M&L for TMT bars 6mm to 8mm dia in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

M&L for TMT bars 5 mm to 10 mm dia in reinforcement, cut to length, bent to shape required as in stirrups and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

M&L for reinforced cement conc M-25 design mix as in slab supported on walls , beam, and columns in floors,roofs landings , balconies etc.

M&L for reinforced cement conc M-25 design mix as in Columns, pillars, piers, posts and struts

M&L for reinforced cement conc M-25 design mix as in beams, cantilevers, bressummers, lintels over 1.5m span

M&L form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface horizontal or sloping, fair finished surface of concrete, all as specified .

M&l Form work to sides and soffits of roof beams incl supports over hangs etc finished rough

M&L Form work to edges of concrete flats, breaks ,conc railing nexc 200mm wide finished roughthick

M&L Formwork to sides of square/Rectangular etc pillars, posts, struts, piers,columns, and stanchions rough finish surface all as specified

M&L 5cm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4, complete as specified & directed

Cutting chases,pinning in making good to facing where requried and pointing in cement mortar 1:3 to ends or edge of landings,steps,cills,sunshade,shelves, lintel etc. tubes or concealed conduit etc. and making good, cutting not exc 10 cm girth

M&L for 10 mm thick screed bedding in cement mortar 1: 4 on concrete surfaces, finished Fair & even including mixing water proofing compound as per manufacturer's instns( WPC to be measured separately as supply only)

Supply only integral water proofing compound complete all as specified.

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg/sqm incl cleaning surface complete all as specified and directed.

S&F APP based polymeric membrance min weighing 3kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric land on primed surface by force application complete all as specified.

M&L Lime concrete in terracing all as specified.

M&L 40mm thick brick tiles laid bedded in 15 mm thick cement mortar (1:6) joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete , of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified

M&L for pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete , of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified

M&L for providing cement concrete 1:3:6 type C-0 using 20mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast complete all as specified.

M&L for factory made, 2nd class hard wood 35 mm thick, plain framed, panelled shutters (one/two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for 35 mm thick second class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, (without sash bars), edges of framing plain, chamfered or rounded, fitted with beads for securing glass,gauge , etc, size of members of shutter as specified in SSR Part-I, Section 8, clause 8.20 (a), fitted to chowkats complete all as specified.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings.

S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site. complete all as specified.

Supply and fixing of mild steel cold rolled butt hinges medium weight 100 mm log fixed to steel /angle iron frame by welding ,if required complete all as specified.

S&F steel locking bolts with mils steel electrogalvanised plate and bright bolt ont less than 10 mm dia and 100 mm size, complete all as specified .

S&F for 150mm size aluminium anodised barrel tower bolt of extruded section and fixed.all as specified and directed.

S&F for 150mm size aluminium anodised handle of febricated type and fixed.all as specified and directed.

Material and labour for 150mm Mild steel pressed handles, oval type, stove enamelled black

S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-charge.

Material and labour for 250mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

Supply and Fixing Anodised aluminium door frame, shutters shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified.

Supply and Fixing Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

Supply only 5.50 mm thick, sheet glass, ordinary quality, in squares not exceeding 0.50 sqm each pane

Supply only 5.50 mm thick, sheet glass, ordinary quality, in squares exceeding 0.50 sqm each pane

M & L Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

Material and labour for 75mm length of Mortice latch with two levers (vertical type), aluminium, anodised body and fixed

S&F factory made pressed steel box type Window/ventilator with upper top hung shutters and bottom fixed type shutters including pintol hinges,steel peg stay and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately Note:- provision for cooler opening where ever required shall also be provided all as directed by Engineer-in-charge.

M&L Mild steel framed work such as grills, gratings, tank staging etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks, cooler stand and similar work conforming to Fe 290 Gd E-165 all as specified .

S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares n exe 0.5 sqm each pane all as specified

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and avg width of aperture1.18mm

S&F20 mm dia decorative drapary curtain road with bibs, braked & internal funnels. complete all as specified.

S&F Wooden finish brackets and end stops of approved finish.

S&F 18/19mm thick prelaminated particle board exterior grade prelaminated one side decorative choice of lamination and other side balancing white fixed with screws to timber frame work including leaping of teak wood scantling on exposed surfaces.

S&F 18/19mm thick block boards grade 2 quality interior grade commercial type as in C/B shelves/wall partitions

S&F continous (piano)type hinges mild steel, bright finish or electrogalvanisedwidth of flap 30mm wide

S&F 150mm long fancy type aluminum handle

S&F Anodised aluminium snap grid frame work size 605x605 mm for false ceiling all as specified

M&L Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and directed by engineer in charge

M&L Cement concrete 1:2:4 type B-1, using 20mm graded crushed stone graded aggregate as in coping benching or bands incl all necessary form work

M&L Rotational moulded two layer polyethylene water storage tank (cylinderical vertical with closed top) ISI marked, hoisted and fixed in position all as specified in SSR Part-I of capacity 500 litres including brass float ball & all accessories, all as specified.

S&F 20 mm bore stop cock chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule.

M&L for 20 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm complete all as specified.

M&L for 15 mm bore steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm complete all as specified.

S&F water closet pedestal pattern colour (as approved by Engineer-in-charge) Make CERA CAT PART No (EWC S1021106 cistern S1060102 Clair soft Seat cover B1520108 Twin flush cistern B1810103 CLAIR DELUXE complete all as specifed.

S&F WHB coloured 615mmx510mm with pedestal white colour Make CERA CANTON Cat No (WHB S2040122, PEDESTAL S2090107) complete all as specified.

S&F half stall urinal flat back (large) 635x395x420 white colour . Make CERA CALCIA CAT No: 5001/ S4020107

S&F CP wastecoupling 32mm dia PTMT (half or full threaded ) minm wt 450 gms .

S&F PVC waste pipe 32mm bore with cup and washers complete.

S&F 15mm bore centre hole basin mixer with round spout with 450mm long copper pipes and brass nuts with out Pop up Make: Jaquar Cat No CON 167KNB

S&F self closing angle cock pressmatic for urinal with flange and spindle 200 mm connecting pipe and spreader.Jaquar Cat No:PRS 077

S&F 15mm bore Bib tap MakeJaquar Cat No CON-107KN

S&F 15mm bore angular stop cock with wall flange Make: Jaquar Cat No CON- 059KN

S&F PVC connection 15mm bore 450 mm long Braided Hose with M10X1 Nipple, 15 mm Nut, O-Ring & Rubber washer (Suitable for Basin Mixers) Make: Jaquar Cat-ALD-803AB

S&F PVC connection 15mm bore 450 mm long Braided Hose with two 15 mm Nut, & Rubber washer without nipple Make: Jaquar Cat-ALD-805B

S&F chromium plated toilet paper holder make Jaquar at No ACN 1153N

S&F Glass shelf with chromium plated guard rails Make Jaquar Cat No ACN-1171N

S&F 600mm long brass chromium plated towel rail fancey type make Jaquar Cat No ACN-1111NM

S&F soap dish Make Jaquar Cat No ACN 1131N or eqivalent

S&F towel rack Make Jaquar CAT NO ACN 1181FN or equivalent

S&F Double Coat hook cat No ACN 1161N

S&F 100mm bore CI sand cast iron pipe in any length with or with out ears laid in trenches or in floors

S&F 75 mm bore CI sand cast iron pipe in any length with or with out ears laid in trenches or in floors

DO but 50mm bore fixed to walls

S&F cast iron cowl 50mm bore

S&F 100mm bore CI sand cast iron branch piece single (Equal or un equal) 'T" reduce oridinary or inverted with parallel branches

DO but 75mm bore

S&F sand cast iron bend (any radius) 100m bore dimnishing pieces or tapers (larger bore measured ) fitted with oval acess doors

Do but 75mm bore

M&L for run lead joint to 100mm bore sand cast iron pipe

M&L for run lead joint to 75mm bore sand cast iron pipe

S&F 100m bore sand cast iron 'P' or 'S" trap .

S&F salt glazed stone ware gully trap , square or rounded mouthed type "P" of size 150mmx150mm

S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 50mm bore pipe

M&L for preparation of new wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified.

M&L for preparation of newly steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of primer. all as specified.

M&L for preparation of preprimed steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint all as specified.

M&L for prep of surfaces of old or new surfaces and aplying a thin layer of wall care puty on wall to give a uniform finish as app by Eng-in -charge and reqd at site

M&L for prep of surfaces of old or new surfaces and aplying a thin layer of wall care puty on ceiling to give a uniform finish as app by Eng-in -charge and reqd at site

M&L two coats of oil bound distemper on walls including preparation on new/old surfaces over coat of primer complete all as specified and directed. .

M&L two coats of oil bound distemper on ceiling including preparation on new/old surfaces over coat of primer complete all as specified and directed. .

M&L for three coats of white wash on newly plastered surfaces

M&L two coats of Exterior emulsion paint on walls including preparation on new/old surfaces complete all as specified and directed. .

Surface excavation (not exceeding 30cm deep) and averaging 15 cm , getting out in any type of soil.

Removal of excavated material to a distance nexc 50 m and depositing at a level nexc 1.5 m above the starting point

Rolling and consolidating formation surfaces in cutting by power roller Exc 8 tonne & n exc 12 tonne

M&L hardcore of broken stone or boulders gauge n exc. 63 mm, deposited, spread and levelled in layer n exc. 15 cm thick watered and rammed to a true surface and rolled by power roller Exc 8 tonnes & n exc 12 tonne

M&L cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foudation, filling, sub base and mass concrete all as specified.

M&L for 150 mm thick Cement concrete type B-2, 1:2:4 (40mm graded aggregate) as in hardstanding and paving, etc complete all as specified and directed. PCC laid in alternate pannel incl all necessary formwork. (Note: (i) The flooring shall be laid using vaccum dewatering process. (ii) Integrally cast slab, joint 10 mm wide and upto depth 1/3 of floor thickness to be cut with cutter machine. The panel size shall not be more than 4 Sqm. The joint shall be filled with polysulphide sealant of approval. Rates included in this item)

M&L Forming 20mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade `B' as in thickness of concrete slab 150 mm

Surface dressing in soft & loose soil n exc 15 cm deep

M&L for 75mm thick PCC (1:3:6), type C2 using 40mm graded stone agg as in sub base of floors etc finished even and rough complete all as specified and directed.

Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-25 Grade to IS 15658-2006 manufactured using grey cement and no pigment complete all as spcified and directed.

M&L for sand filling under floors, cushning under interlocking tiles or in foundations complete all as specified and directed.

M&L for 15mm thick Rendering in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, finished fair and even complete.

Excavation in trenches n exc 10Sqm on plan n exc 1.5 m deep and n exc 1.5 m wide , getting out in any type of soil.

Returning filling in incl spreading levelling watering and well ramming in layers n exc 25cm thickness.

M&L for PCC 1:4:8,type D-2 using 40mm graded crushed stone aggregate as in sub base and mass conc.

M&L for conc 1:3:6 type C2 using 40mm graded aggregateas in bed to 150mm drain pies incl packing under and haunching against the sides of pipes after they are laid and tested for.

S&F salt glazed stone ware drain pipe 150mm bore in trenches and jointed as spfd

M&L brick work in cement mortar (1:4) using old size sub class 'B' bricks in walling, straight or curved on plan exc 6m mean radius all as specified.

M&L rendering 15mm thick in cm 1:4 concrete walls or stone masonary walls surfaces as in wall finishes even andsmooth w/o using extra cement incl mixing of wpc .(Note: WPC shall be measured and paid for seperately)

M&L For PCC type B1(1:2:4) using 20 mm graded cushed stone agg as in coping ,benching and the like incl form work

M&L Precasted RCC 1:2:4 type B1 using 20mm graded aggregates for precast cement conc slabs as in drain/ manhole covers set in cement mortar1:4.(Note : Slab covers shall be floated with surface vibrator,and over turfed base ,arrandement for turfed base has to be from contractors side)

M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete ,using extra cement ,incl forms moulds ,mitered/stopped ends etc

Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc complete all as specified and as directed by the Engr-in-Charge.

Taking down of unserviceable DBs/switch fuses/changeover in sheet steel enclosure complete with MCBs/Fuse/grips any capacity and removing from site and making good disturbed surface of wall, floor etc. Taking after disconnecting all cable complete all as specified and as directed by the Engr-in-Charge.

M&L Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid PVC concealed conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.0 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 154 here-in-before but socket point on the same board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No 154 here-in-before but socket point on indpendent board complete as specifed as directed by Engineer - In - Charge

All as per item No 154 here-in-before but cable of 2.5 Sq mm for 15 Amp switch socket outlet on independent board

All as per item No 154 here-in-before but cable of 4 Sq mm for 15 Amp switch socket outlet on independent board

S&F Switch piano flush type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge Make : Anchor/ Legrand/Wipro/Havells

S&F Socket outlet 2 in 1, flush type, 3 pin, 5 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : -Anchor/ Legrand/Wipro/Havells

S&F Switch piano flush type, Single pole 15 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge Make : Anchor/ Legrand/Wipro/Havells

S&F Socket outlet flush type, 3/5 pin, 5/15 Amps, ISI marked, complete all as specified and as directed by Engineer-in-ChargeMake : -Anchor/ Legrand/Wipro/Havells

S&F Lamp holder insulated body with back plate for conduit/casing capping fittings complete incl LED 9W bulb all as specified and as directed by Engineer-in-Charge. Make :- Anchor/ Legrand/Wipro/Havells

S&F Ceiling rose PVC/poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : Make : Anchor/ Legrand/Wipro/Havells

S&F LED bulk head luminaries 10 W , complete all as specified and directed by Engineer-in-Charge. Cat Part No. SLE BH 10 W in make Surya / Bajaj/CG

S&F Ceiling fan regulator electronic type, 230 Volt, 150 Watt with 5 step of control including making holes in laminated bakelite sheet cover and connection complete all as specified and as directed by Engineer-in-Charge. Make ANCHOR/ LEADER/SSK.

Supply & fixing in replacement Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp, 240 Volt.

S&F Sheet metal enclosure for distribution boards double door, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 8 ways, supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make - Legrand/ GE/Seimens/L&T/Schneider/Indo Asian/C & S/ABB/Strandard/BCH/HPL

S&F Sheet metal enclosure for distribution boards double door, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 4 ways, supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make - Legrand/ GE/Seimens/L&T/Schneider/Indo Asian/C & S/ABB/Strandard/BCH/HPL

S&F in replacement Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 415 volts with 200 Amps rated bus bar, load line DB's are fittied with bus bar nutural links blank plates TPN vertical load line 4 ways suitable for TP/FP 'A' frame MCCB,includeing 63 Amps MCCB -01Nos ,MCB SPN 32 -05 Nos and MCB SP as required, complete all as specified and as directed by Engineer-in-Charge. Make - Havells / Legrand/ Indo Asian Note : cost of cutting/chasing of wall and making good disturbed surface deemed to be included in the rate

S&F MCB single pole, 240 volts of rating 6-32 Amps, breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge Make :- Schneider/ HPL/Legrand/ GE/ Seimens/L&T/Indo sian/C&S/Havells/BCH/ABB

S&F MCB suitable for 6 to 32 Amps, 240 Volt AC supply single pole and neutral with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge. Make :- Legrand/ GE/ Seimens/L&T/Indo Asian/C&S/ABB/BCH

M&L for submain wiring using 2 runs of single core FRLSH PVC insulated, unsheathed stranded copper conductor cable of size 2runs of 6 Sqmm of voltage rating 1100V for Single phase & neutral, drawn in and including concealed PVC conduit of dia not less than 25 mm dia with standard acessories, along with two run of FRLSH PVC insulated, unsheathed, stranded copper conductor of size 2x 6.0 Sqmm as earth continuity conductor all as specified and directed(Note-2 runs of single core FRLSH PVC cable 6sqmm for Single phase & neutral with one run of earth conductor as earth and conduit shall be measured as one unit)

S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Philips-BN021 LED 20S PSU CW GR S2/ Crompton Greaves LDDR20-CDL Dazzle Ray / bajaj-BCLAB 20W

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanized iron and steel earth wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

JAGDAMBA CONSTRUCTION COMPANY

vipul construction company

Beenu Co. Company

M/S ASHRAFI CONSTRUCTION CO