SPECIAL REPAIRS TO BLDG No. 2 ABNS LINES AT CDO WING AREA OF HQ JL WING, THE INF SCHOOL UNDER GE I BELGAUM

Amount

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thick, below or above GL all as specified and directed.

Dismantling boarding of any description fixed in any position with nails all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls, ceilings, etc. including raking out joints, hacking for key scrubbing down with water etc.

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C0, using 12.5mm graded stone aggregate and setting in CM 1:6 including demolition of existing unserviceable PCC block masonry built in cement mortar all as speified and as directed.

M&L plain cement concrete 1:3:6, type C-1, using 20mm graded stone aggregate as in coping, bed blocks, eaves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work including dismantling of existing unserviceable timber scantling 40 Sq.cm and over in section and in any position in un-framed work and making good disturbed members all as specified and directed.

Dismantling timber scantling 40 Sq.cm and over in section in any position in un-framed work and re-fixing the same in new or old position all as specified and directed.

S&F in repairs galvanised steel wire cloth 0.56 mm nominal dia of wire & average width of aperture 1.18mm fixed in panel of joinery all as specified and directed.

M&L for Roof trusses (framed), trussed, purlins (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-410-W Gde-E-250 quality-A all as specified and as directed.

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions including dismantling of existing unserviceable Mangalore pattern tiles roofing alongwith wooden battens, shingles, tilting fillets, etc of any description and size and making good disturbed roof members all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

S&F pre-painted galvalume coated high tensile plain steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.5mm thick (TCT), as in ridges, valleys, hips, claddings, etc. fixed with self drilling fasteners as per manufacturers instructions including dismantling of existing unserviceable Mangalore pattern ridges of any description and size and making good disturbed members all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for 12mm thick Plywood, 7 ply, grade BWP, type BB fixed with screws to timber frame work as in sub base for flooring including taking down existing unserviceable boards of any description and size all as specified and as directed

M&L for 20mm thick 2nd class hard wood boarding, clean sawn, with butt joints, as in sub bases for flooring, fixed with nails all as specified and as directed

M&L for 3mm thick PVC tiles/ sheets, laminated plain coloured, marbled mosaic or mottled finish, as in floors, laid with approved rubber based adhesive all as specified and as directed.

M&L for plain cement concrete 1:3:6, type C2, (Using 40 mm graded stone aggregate), 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M &L for 4mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane, fixed in repairs, all as specified and directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable), any colour, over a coat of primer on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces with chalk whiting all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable) over a coat of primer over 1mm thick layer of wall care putty, on walls, pillasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L for one coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

Taking down carefully point wiring of any description complete for light, fan, 5 A socket, 15 Amps socket, 2 way points and bell point etc including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, holders, light fitting, etc. all as specified and directed.

M&L for Point wiring complete with 1.5 Sq mm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC casing capping of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 2nd class HW board fixed on wall with sunmica top for mounting switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed. all as specified and directed.

All as described in item No. 26 but for one light point controlled by 2 Nos. of 2 way switches.

All as described in item No. 26 but for one ceiling fan/ exhaust fan point controlled by one switch and regulator.

All as described in item No. 26 but for one 05 Amps socket outlet on independent board.

All as described in item No. 26 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 26 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 4 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 4 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 4 sqmm cable, one run of 4 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

M&L for sub main wiring with 2 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 6 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 6 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Two runs of 6 sqmm cable, one run of 6 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

M&L for sub main wiring with 4 runs of single core PVC insulated FRLS unsheathed multi-stranded copper conductor cables of size 16 sqmm drawn through and 1100 volt grade including PVC casing and capping of suitable size with all necessary fittings and provision of one run of 16 sqmm PVC insulated FRLS unsheathed multistranded copper conductor single core for earth continuity and connected to common earth dolly, including taking down existing unserviceable sub main wiring of any description and making good disturbed surfaces complete all as specified and directed. Note: Four runs of 16 sqmm cable, one run of 16 sqmm earth conductor cable and one run of PVC casing and caping shall be measured and paid together as one unit length.

S&F switch, piano type, 5 Amps, flush button, 230 volts, AC, one way all as specified and directed.

S&F switch, piano type, 5 Amps, flush button, 230 volts, AC, 2 way all as specified and directed.

S&F switch piano flush type 15 Amps 230 volts all as specified and directed.

S&F socket outlet 15 Amps 3 and 5 pin 5 and 15 Amps flush type multipurpose all as specified and directed.

S&F socket outlet 5 Amps 3 and 5 pin flush type multipurpose all as specified and directed.

S&F ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F fan regulator electronic step type suitable for 1200/1400 mm sweep ceiling fan all as specified and directed.

S&F in repairs, MCCB DB VTPN 12 Way, vertical type, suitable for MCCB as incomer 415 volts rated bus bars double door type including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCCB DB on board complete all as specified and directed.

S&F MCCB TP 125 Amps ,25KA, 415 Volts, AC supply, fixed thermal magnetic settings, all as specified and as directed.

S&F in repairs, MCB DB TPN 4 Way with 200 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB TPN 63A 10KA 'C' series 50Hz 415 Volts AC supply all as specified and as directed.

S&F in repairs, MCB DB SPN 12 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F in repairs, MCB DB SPN 4 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F MCB DP 40A 10KA 'C' series 50Hz AC supply including dismantling old one all as specified and as directed.

S&F MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

S&F surface mounting LED light fitting, 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 20W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED light fitting, 10W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 10W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F surface mounting LED light fitting, 5W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 5W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F 42 Watts LED glare free luminaire recess mounted in square profile 2ft x 2ft size with 42 W high brightness LEDs including electronic driver etc. complete with all accessories internally pre wired including cutting of false ceiling sheet to required size and fixing aluminium strip as per the existing size in false ceiling for fixing of light fitting and providing aluminium strip supports as reqd and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block all as specified and directed. Make: HAVELLS VENUS NEO HE 2 x 2 or equivalent in CG/ Philips/ Wipro.

S&F 25 Watts LED security light fitting, with pressure die cast aluminium housing and lens embedded PC cover having top opening separate driver compartment with IP65 protection, 25 Watts high power LEDs, electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of GI pipe light grade of suitable size and length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA PEARL model of HAVELLS or equivalent in Crompton Greaves/ Philips/ Wipro

S&F ceiling fan, 230 volts, single phase, 1200mm sweep, 5 Star rating with all accessories and provision of suitable size of flexible copper conductor cable fro connector to terminals and taking down existing unserviceable fan of any description and size and depositing in MES stores complete all as specified and as directed. Make: HAVELLS Model No. ES-50 Premium 5 STAR rating or equivalent model in makes CG/ USHA

Taking down exisitng light fittings of any description and type and refixing the same back to its original or at other locations as directed by Engineer-in-charge including provision of required size new copper conductor from ceiling rose to connector block of light fitting all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (upto 7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (upto 7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

M/s. J P CONSTRUCTIONS

M/s.Y.N.PATIL

M/S SAMARTH CONSTRUCTIONS

SHRI.H.R.PATIL