PROVN OF WASHROOM ADJACENT TO LRMR HANGER AND PROVN OF WOODEN CUPBOARDS IN OTM BUILDING AT INS UTKROSH UNDER GE MINNIEBAY, SRI VIJAYA PURAM

Excavation in trenches in Soft / loose soil n.exc. 1.5M wide and n.exc. 1.5M deep and getting out complete all as specified and directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5M complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level) etc., complete all as specified and as directed.

M&L RCC M-30 Nominal mix using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams etc., and mass concrete complete all as specified and directed.

M&L RCC M-30 Nominal mix using 20mm graded stone aggregate as in beams, cantilevers, bresuemers, lintels over 1.5m span etc complete all as specified and directed.

M&L RCC M-30 Nominal mix using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts etc complete all as specified and directed.

M&L formwork to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides and soffits of foundation (if any) and plinth beams for rough finished surfaces of concrete, flat, complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete, flat, complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beam, beam haunching, girders, bressum-mers lintels, cantilevers, shelves, including support, overhangs, etc also splays between floors and beam etc complete all as specified and directed

M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed

M&L PCC (1:4:8) Type D2 using 40 mm graded stone aggregate in foundations, filling and mass-concrete all as specified complete all as specified and directed

M & L for bringing approved earth from out side MD land and spreading in layers n exc. 25 cm thickness including watering complete all as specified and directed by Engineer in charge.

M&L Pre-cast cement concrete block masonry Type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and directed.

M&L for rendering 10mm thick plaster in CM (1:6) on brick/block or concrete surfaces finished even & smooth etc., complete all as specified and as directed.

M&L for rendering 15mm thick plaster in CM (1:4) over a concrete or block masonry surfaces including mixing water proofing compound on top layer as per manufactures instructions (or 3% by weight of cement) and finishing the top surfaces even and fair etc., complete all as specified and as directed. (Note :Water proofing compound shall be measured and paid seperately under relevant item of this schedule as supply only).

M&L proparing newly plastered surfaces of wall and applying two coats of high sheen, Anti-Fungal, Excellent Stain Resistant interior Acrylic emulsion paint over a coat of primer complete all as specified and as directed by Engineer-in-charge. Make: Asian Paints (Tractor uno), Berger (Bison Emulsion), Nerolac (beauty smooth), Shalimar Paints (No.1 Silk).

M & L for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal esistance, dirt resistance exterior paint of WHITE colour with silicon additives coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm over new surfaces complete all as specified and as directed by Engineer-in-charge. Make: Asian Paints (Apex Ultima), Berger (Weathercoat Long Life Flexo) Nerolac (Excel Total). Shalimar Paints (Weatherpro+ Super Luxury Emulsion).

M&L for PCC (1:4:8) type D2 (using 40mm graded aggregate) 100 mm thick as in subbase of flooring complete all as specified and directed

M&L for coloured non-skid ceramic tiles 7 to 8 mm thick exc. 0.06 sqm but n.exc 0.11sqm area of each tiles in floor/ steps etc set and jointed in neat cement slurry and pointed in coloured cement to match as in floor over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed

M&L for glazed ceramic coloured/printed tiles 450x350x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile over 10mm thick backing in cement mortar (1:3) complete all as specified and directed

M&Lfor vitrified double charged coloured ceramic tiles 10 mm thick ( Square/ rectangular) area of each tiles not exc 0.36 Sqm in floors set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified and directed

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed in CM(1:6) and rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed

S&F of 6mm thick sheet figured glass pin headed type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required, complete all as directed.

Supply and fixing factory made uPVC any colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws,etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and laying of CPVC pipes 20 mm dia outer bore SDR 11 & plain CPVC SDR 11 fittings on walls /ceilings or laying in floors complete all as specified.

S&F 20 mm bore CPVC Brass Elbow all as directed.

S&F 20 mm bore Brass Elbow reducer(3/4 x1/2) Elbow all as directed.

S&F 20 mm bore CPVC Male Brass Threaded Adaptor (MTA/MBTA) Elbow all as directed.

S&F 20 mm bore CPVC Female Brass Threaded Adaptor (FTA/FBTA) Elbow all as directed.

S&F 20 mm bore CPVC Brass Tee Elbow all as directed.

S&F 20mm bore CPVC Brass Union Elbow all as directed.

S&F 25mm dia aluminium anodised best quality curtain rod alongwith brackets long body in pairs fixed both ends (rates included of brackets) complete all as specified and as directed.

S&F in repair Vitreous china white heavy duty Counter Top wash hand basin of 520x440x180mm size, including waste coupling and waste pipe complete all as specified and directed.

S&F Vitreous China wash down water closet pan of size 540x375x415mm 'P' trap or 'S' Trap (pedestal pattern), any colour including necessary fittings and flush pipe etc (excluding flushing cistern) all as directed.

S&F 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, any colour , with inlet, ball valve, float and handle including brackets, and necessary connections to pipes all as directed.

S&F PVC water closet seat cover (any description and any colour), closed pattern and mild steel chromium plated or aluminised hinging device all as directed.

S&F brass chromium plated Hand shower (Health Faucet)(ABS Body) with 1.00 Meter long Easy Flex Tube in Chrome Finish and wall Hook all as directed

S&F CP Towel Ring fixed with and including Chromium plated brass screws and wall plugs (Minimum weight 90gms) all as directed

S&F Pillar taps, cast copper alloy chromium plated, fancy type, screwed down, high pressure with long screwed shanks and fly nut of 15/20mm bore all as directed.

S & F Bib Taps, cast copper alloy heavy duty, 15 mm dia, Chromium Plated, long body Fancy Type screwed down for iron pipe and fixed etc complete all as specified and as directed.

S&F two way bib tap cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore all as directed.

S&F Angular stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore all as directed

S&F 15 mm dia Stop cock chromium plated fancy type with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe/CPVC pipe or for unions and fixed all as directed.

S&F PVC connection 15mm size with CP brass Nuts of legnth 600 mm complete all as specified and as directed.

S&F 100mm dia CP grating incl joints with solvent cement complete all as specified and directed.

S&F 600 mm long CP Brass Towel Rail fixed to wall with necessary chromium plated screws and wall plugs all as specified,

S&F Waste pipe any dia (32/40mm) alongwith necessary fittings connected to wash hand basin /kitchen sink all as specified.

S&F CP Toilet paper holder fancy type high quality all as directed

M & L MS Rolled sections as in posts , main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc vertical posts .conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley gutter, drip, and straight flashing all as specified and as directed

S & F Aluminium flat iron work in wind ties 40x6mm size fixed with 50mm/ 75 mm aluminium self staging screws with integral EPDM washer screwed in roof covering all as directed.

M&L for providing cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) as in coping, benching,, bands , lintels, beam span less than 1.5 mtr length and similar works slightly rounded or chamfered angles and throating including necessary form work as directed

M&L for applying a layer of 1mm thick wall care putty on wall and making surface even and smooth complete all as specified and as directed.

M & L Preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as secified.

Providing & fixing false ceiling with semi perforated 12mm thick micro tegular edged GRG false ceiling tiles at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge.

M&L 75mm thick PCC 1:3:6 Type C-2 using 20mm crushed stone aggregate as in plinth protection, flooring etc finished even and fair without using extra cement all as specified.

S&F 150 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors all as directed

M&L Concrete bed to drain pipes 150 mm dia including packing under and haunching against the sides of the pipes after they are laid and tested all as directed

M&L for PCC (1:3:6) Type C2 ( using 40 mm graded stone aggregate) in surface channels and PCC drains complete including necessary formwork all as specified and directed.

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone agg as in cover slab and set in cement mortor 1:6 complete incl necessary form work.(Reinforcement shall be measured and paid seperately )

M&L TMT bar 10mm dia and over cut to length bent to shape reqd incl cranking binding spirally for hooking,binding with and including mild steel wire (Annealed) not less than 0.9mm dia as in reinforcement complete all as specified.

M&L for TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups spaces and binder cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

S&F PVC (SWR) floor traps 100mm bore with stainless steel grating (measured seperately) including jointing to waste pipe and fixed in cement concrete 1:2:4 type B-1 all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing all as directed

S&F PVC Septic tank of capacity 2000 LTR including excavation and Returning, filling all as specified and directed. Make plasto or sintex or equivalent

Material and Labour Point wiring with 1.5 Sqmm (nominal area), FRLSH PVC insulated, multistranded, single core, unsheathed, copper conductor cables drawn through and including PVC conduits Concealed in walls, ceiling etc with all fittings and accessories of PVC conduits (like Tee, bend etc.) complete fixed to walls/ceiling etc. with and including 1.5 Sqmm (nominal area) FRLSH PVC insulated, unsheathed, multistranded, single core, copper cable green in colour as in earth continuity wire connecting to common earth point and 1.6 mm thick mild steel sunken terminal boxes of suitable size with 3 mm thick hylam sheet top cover fixed with suitable size of brass screws for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point/ 3 pin 5 Amps socket outlet independent point controlled by one, one way switches complete including cutting, chasing the surface and then making good the same in CM 1:3 complete all as specified and directed by the Engr-in-Charge.

All as per item No. 70 here-in-before but one 3 pin 5/6 amp switch socket out let independent all as directed

All as per item No. 70 here-in-before but one 3 pin 5/6 amp switch socket out same board all as directed

All as per item No. 1.00 here-in-before but using 2.5 Sqmm size stranded copper conductor cable for one 16 Amp switch socket outlet point on independent board complete PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified and directed by Engineer-in-Charge.

S&F ceiling rose, surface bakelite, 65 x 50 mm,three terminals complete all as specified and directed. Make:- Anchor Cat No 39040/3290/ Havells/ Plaza / Cona.

Supply & fix Modular type switch 6 Amps 230V AC single module one way complete all as specified and as directed. Make:-Anchor Cat Part No.210011M or equivalent model from make:- Legrand / Havells.

All as per item No. 02 here-in-before but socket outlet 10/20 Amps 3 Pin shuttered type 230V AC 2 module complete all as specified and as directed. Make:- Anchor Cat No.34374 or equivalent model from make of Legrand / Havells.

Supply & fix modular cover plate with frame for fixing of modular switches/sockets complete for 1 modules complete all as specified and as directed. Make:- Anchor Cat part No.30216WH or equivalent model of Legrand / Havells.

All as per item No 77 here-in-before but for 2 modules. Make:- Anchor Cat part No.30227WH or equivalent model from make:- Legrand / Havells.

Supply & fix Modular socket outlet 6 Amps 3 Pin shuttered type 230V AC 2 module complete all as specified and as directed. Make:- Anchor Cat No.21102 or equivalent model from make:- Legrand / Havells.

Supply and fixing in LED mirror light 7 watt design complete all as specified and as directed. Make:-Philips Jojoba cat No- 34034 Panasonic/ Wipro/ Rashmi/Bajaj

Supply and fixing in LED wall light 12 watt design complete all as specified and as directed. Make:-Philips cat No- 1739330 / Panasonic / Wipro / Rashmi/Bajaj

Supply and fixing sub main wiring with two run of single core 6 Sqmm PVC insulated unsheathed stranded cable copper conductor drawn through PVC conduit not less than 25 mm dia with all fittings including 6 sq mm PVC insulated unsheathed single core copper conductor as earth wire and including PVC conduit all as specified and as directed. Note : (i) Two run of single core cable 6 sq mm and one run earth wire 6 sq mm will be measured as one length.

Supply and fixing MCB SPN DB made up with sheet metal double door, phosphorised, power coated, neutral link, earth bar and din rail,4 way with 200 amps rated bus bar, 240 volts complete all as specified and as directed. Make:- L&T Cat part No.DBSPN004DD/Legrand cat no- 507600or equivalent ABB/ C&S Electric Ltd.

Supply and fixing MCB 32 Amps, DP 240 Volts ,B- Curve breaking capacity 10 KA as directed by the Engr-in-Charge. Make:- Legrand Cat Part No 408617 or equivalent in L&T Cat part No.BB20060B to BB20320B/ Hager/ Siemens/ ABB/ Schneider.

Supply and fixing MCB 6 to 32 Amps, SP, 240 Volts ,B- Curve breaking capacity 10 KA as directed by the Engr-in-Charge. Make:- Legrand/ L & T/ Hager/ Siemens/ ABB/ Schneider.

Supply & Fixing Exhaust fan AC single phase 240 V of size 250 mm sweep with louvre specially designed by kitchen in domestic ventilation.plastic body and blade, finish high quality engineering plastic heavy duty motor, protective bird guard,complete all as directed and specifed. Make - Havells/KHAITAN /CG or equivalent. Note-: Taking down old fan and depositing to MES store

Material and labour for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.00 mm thick burried in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI strip 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of GI or steel, GI strip proected by 40 mm bore light grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade galvanised iron, wire mesh, charcoal or coke common salt laid in alternative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1, 50 mm thick pre-cast RCC (1:2:4) type B-1 normal mix cover slab reinforced with 8 mm dia TMT bar 10 cm c/c bothways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft / loose soil and disposal pf soil to a distance n. exc. 50 m and necessary testing on completion all as shown in electrical plate No. 3 MES Schedule Part-I complete all as specified and as directed.

Supply and laying GI pipe medium grade with all fittings in trenches :- (a) 40mm bore of GI pipe

(b) 25mm bore of GI pipe

Supply & fixing gun metal 25mm bore gate valve including taking out the U/S old one (ISI marked) screwed down high pressure with handle with iron wheel both ends screwed for iron pipe.

Materials and Labour for Construction of brick masonary valve pit chamber of sizse 1050x1050x1050mm internal dimension using sub class-'B' bricks in CM (1:6) plastering in cement mortar (1:4) externally & internally extended to 15 cm below ground level including PCC bed 10 cm thick in PCC 1:3:6 Type C2 with MS frame fabricated by angle of size 40 x 40 x 6mm complete with top cover of 3 mm thick MS sheet & locking arrangement and painting with two coats of synthetic enamel over a coat of red oxide primer including demolition of old unserviceable damged valve pit complete all as specifed & directed.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate with and including all necessary form work including demoltion of old PCC/broken PCC complete all as specified & directed

Materials and Labour Cutting /boreing of existing road / path , hardstandingetc for taking out cable and water pipe to protection with iron cover plate for passing cable,water pipe and making good the disturbed road top surfaces with following cement concrete all type, using of suitable depth and finished with speed breaker complete all as uder directed by Engineer-in-Charge.

Supply and laying dry coarse sand as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 Cm (15 Cm under the cable & 8 Cm over the cable) and gently punned down to 18 Cm thickness complete all as specified and as directed by the Engr-in-Charge. Note:- Thickness after punning down shall be measured for payment.

Supply & laying in replacement Telerex DWC (Double Wall Corrugated) HDPE pipe ISI marked of outer dia of 50 mm and inner dia 38 mm polyethylene including couplers, bends, cap etc., with smooth internal and profiled external surface for non pressure under ground cable complete all as specified and directed

Supply and laying XLPE insulated PVC sheathed, armoured, aluminium conductor cable 1100 Volt grade 6 Sqmm 3.5 core in duct/floor/wall with provision of saddle and lugs, joints etc including connection complete all as directed by the Engr-in-Charge.

Supply and fix LED decorative post top lantern,20 Watt capacity for energy efficient conservation upto 50% and with eco friendly lighting system with all accessories and necessary connection including taking down old unserviceable one complete all as specified and as directed.

Supply and laying GI pipe light grade 80mm bore with all fittings in trenches for road cutting all as directed.

S&F for factory made single extruded 18/19 mm thick WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc., complete all as specified and as directed. NOTE:- All joint should be filled with sealant

S&F for 150 mm long Brass handles, cast type, polished bright etc., complete all as specified and as directed.

S&F for 100 mm size hasp and stable , safety type , brass with mild steel hinges pin including bolt to hinge plate with scrows etc., complete all as specified and as directed.

S&F for SS 304 continuous (piano) hinges , mild steel , bright finish or electrogalvanished and width of flaps 30 mm (when open) etc., complete all as specified and as directed.

S&F for Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed etc., complete all as specified and as directed.

S&F 25mm dia stainless steel powder coated curtain rails with fixing brackets in both ends complete all as specified and as directed.

M&L Cutting holes in brick walls (n exc half brick) in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required all as directed.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges:large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

M&L PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in foundation, filling & mass concrete for foundation of fencing posts complete all as specified and as directed.

M&L for rendering 15mm thick plaster in CM (1:6) on brick/block or concrete surfaces finished even & smooth complete all as specified and as directed.

Please Enable Macros to View BoQ information