PROVISION OF TOILET BLOCK NEAR BLDG P-256 AND PROVISION OF SUMP AND CHAIN LINK FENCING AT 267 TRANSIT CAMP AT BRICHGUNJ MILITARY STATION, PORT BLAIR

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil complete all as specified and directed.

Excavation over areas, not exceeding 1.5m deep and getting out in soft/loose soil complete all as specified and directed.

Excavation over area, exceeding 1.5m but not exceeding 3m deep and getting out in soft/loose soil complete all as specified and directed.

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L Precast Cement Concrete Block Masonry with Solid Block, exc 10cm in width in type C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) complete all as specified and directed.

M & L for RCC- M - 30 Design Mix as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and directed

M&L for Reinforced cement concrete design mix M-30 in columns, pillars, posts & struts complete all as specified and directed.

M&L for Reinforced cement concrete design mix M-30 in lintels over 1.5m clear span, beams and cantilevers complete all as specified and directed..

M & L for RCC- M -30 Design Mix as in slabs supported on walls,beams and columns in floors , roofs, landings, balconies,canopies, deck slabs and in,shelves and the likeall as specified and directed

Use & waste of Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides of square or rectangular columns, pillars, posts and struts for fair finished surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides and soffits of beams fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides & soffits of Roof slabs and chajjas for fair finished flat surfaces of concrete complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 6 to 8mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 5 to 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for Rendering 10mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces, finished fair and even complete all as specified and directed.

M&L for Rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished fair & even complete all as specified and directed.

M&L for rendering 15mm thick in two coats on faces of brick work or concrete surfaces; first coat (rendering coat) of 10 mm thick in cement mortar 1: 6 and second coat (finishing coat) of 5 mm thick in cement mortar 1: 4 mixed with water proofing compound (water proofing compound to be measured separately as supply only) and finished even and smooth complete all as specified and directed.

M&L for rendering 15mm thick in in cement mortar 1: 3 on faces of brick work or concrete surfaces on roof top ; mixed with water proofing compound (water proofing compound to be measured & paid separately as supply only) and finished fair and even complete all as specified and directed.

Supply only integral water proofing compound.

M&L Preparation of Newly Plastered surfaces of Wall and applying Two coats of Oil Bound Distemper over chalk whiting including primer as specified and directed.

All as item above but on Ceiling surfaces

M& L for Finishing walls with Acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified and as directed by Engineer-in-Charge.(Make Apex Ultima)

M & L For Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm

Spreading and levelling in layears n. exc 25cm thick and well ramming including watering all as specified and directed

Removal excavated material to a distance not exceeding 50 M and depositing where directed at a level n. exc. 1.5 m above starting point as in soils complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in 100mm thick as in sub base.

M&L 25mm thick cement concrete type B-0 (12.5mm graded stone aggregate) as in RCC roof / Floor surface wfor level coarse

M&L Hard Core of gauge n.exc. 63mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rolled/ rammed to a true surfce.

M&L for PCC 1:3:6 type C1 using 20mm graded aggregate of 75mm thick as in Plinth Protection.

M & L Chequered cement concrete tiles, with grey cement and pigment 30cm x30cm x20mm thick set, jointed and pointed in neat cement slurrry in floors including 15mm thick screed bed in Cm 1:4 all as specified and directed.

M&L Coloured Non-Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc,set and jointed in neat cement sluryy and pointed in coloured cement to match as in floor over 20mm thick screed bed in CM (1:6).

M&L Glazed Ceramic Coloured tiles 350x 250x 7mm/ 450X 350X 7mm thick as in Dado/Skirting/Steps etc set and jointed in neat cement slury and pointed in coloured cement to match all as specified and directed including backing coat 10mm thic in CM 1:6

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm wooden grain printed PVC sheet, edges will be painted to match with printed sheet, reinforced with MS square tube & fixing in opening.

S&F Factory made solid panel PVC door shutter 30mm thick (stiles) consisting of frame made out of MS Tubes for top & bottom rails, MS frame shall be covered with heat moulded wooden grain printed PVC sheet and 5mm thick x 15mm wide PVC sheet beading used inside stiles & rails and decorative PVC beading of 10mmx10mm used instead of exposed portion of PVC sheet beading.

S&F 100 Butt hinges extruded aluminium alloy, anodised. With galvanished mild steel hinge pin , anodised and fixed type B-21

S&F 200mm Aluminium anodised barrel tower bolts of extruded sections.

S&F 150mm Extruded aluminium alloy handles, fabricated type, anodised.

S&L of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings fixed to walls and ceilings or laid in floors complete all as specified.(a) Outer diameter of pipe in 20 mm

(b) Outer diameter of pipe in 25 mm

S & F 1000 litres capacity Rotational moulded polythene water storage tanks(cylindrical vertical with closed top) hoisted in position all as specified in SSR Part I

S&F 15mm Bore Stop Valves / Angle Cock Fancy Type Chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handles screwed both ends.

S&F in repairs Bib tap cast copper alloy chromium plated 15mm dia with fancy type screwed down screwed for iron pipe or brass ferule etc complete all as specified and as directed.

S&F looking mirror Bevelled Edge 600mmx450mm mounted on 6mm thick AC building board or commercial ply wood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed.

S&F Gun Metal Gate valves 20 mm dia with iron wheel head screwed both ends for iron pipes.

S&F Chromium Plated Steel Grating of 100mm size.

S&F Vitreous China Wash down water closet pan pedastel pattern (EWC) white in colour with and incl plastic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipewith connecting Assoceries complete all as specified & directed.

S&F PVC low level flushing cistern 10 litres capacity with inlet ball valve, float and handles including brackets all as specified & directed.

S&F 2 Way Bib Cock Double handle with flange 15 mm bore cast copper alloy Chromium plated with wall flang, screwed down, screwed for pipes. (Make:- Prayag Cat No -8312 or Equivalent)

S&F as in repair Hand Shower (Health Faucet) 1 Meter Long Flexible Tube & Hook. (Make:- Jaquar Cat No ALD CHR -585)

S&F Vitreous China Wash hand basin, white flat back size 550x400 mm including brackets(including Pillar Tap 15 mm bore Chromium plated cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts & PVC waste pipe) all as specified & directed.

S&F vitreous China urinal, half stall type complete including waste pipe, flush pipe & providing and fixing plugs, bedding urinal against wall in cement morter 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement etc, and including connection to flushing pipe and outgoing pipes fixed in repairs complete all as specified and as directed.

S&F PVC flexible connections 15 mm dia 450 mm long with brass checknuts .

S&F 100 mm CI Floor trap with grating incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4).

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in floor.

S&F 75mm dia outlet PVC (SWR) floor trap,plain with grating incl joining with solvent cement

S&F PVC (SWR) Gully 125/110 mm,seting and incl joining with solvent cement

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls and laid in floors

S&F 75mm dia PVC (SWR) bend with oval access door

S&F 110mm dia PVC (SWR) bend with oval access door

S&F PVC (SWR) cowls 75mm dia.

S&F PVC (SWR) cowls 110mm dia.

M&L for Concrete bed to drain pipes including packing under, and completely surrounding pipes with concrete after they are laid and tested in cement conrete 1:3:6 type C-2 around 110mm dia complete.

M&L for precast man holes cover slab with 1:2:4 type B1 using 20mm graded stone aggregate set in CM 1:4 incl cost of use and waste of clean sawn wooden form work but excl cost of reinforcement all as specified.

M&L PCC 1:2:4 type B1 using 20mm graded stone aggregate as in surface channel / benching incl cost of use and waste of clean sawn wooden form work all as specified

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mi-ted/stoped ends etc

M&L in repairs water proofing treatment to RCC roof by priming the plastered surfaces with a coat of cold applied bituminous primer conforming to IS 2488 @ 0.30 kg/sqm and laying APP modified five layer polymeric membrane of minimum wt. 3.50 kg/sqm reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm) laid by torch application as per the manufacturers instructions with side overlap of 100mm & end overlap of 150mm & tucked into the chases on vertical surfaces to a height of 300mm & finally finished with bituminous aluminium paint @ 0.10 kg/sqm complete all as specified and as directed.

S & F Aluminium anodised (minimum anodisation is 15 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, locking arrangements etc., complete with standard aluminium sections, complete all as specified and as directed. (Aluminium section shall be of make Jindal/Hindalco/ Indalco). (Note:- Weight of various Aluminium sections handles and locking arrangements shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, aluminium wire cloth as applicable will be measured and paid separately as supplied only).

Supply only 12 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination and fixed to aluminium frames complete all as specified and as directed.

Supply only 4.0mm thick sheet glass, ordinary quality in squares n exc 0.50 sq.m in each pane.

Excavation in post holes (or similar holes) each not exceeding 0.5 cum getting out in Hard/dense soil returnig filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25cm watering and removing surplus soil to a distance not exceeding 50m and making good surfaces complete.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in Steps, Jambs, Cooking Platform,Dado,Skirting,Floor and like in CM (1:4) of 10mm thick including pointing in white cement (1:2) using admixture of pigment to match the shade of granite stone including Cutting, mitring or rounded smooth edges and Polishing. all as specified and directed.

M&L for providing reinforced cement concrete type B-1 (using 20mm graded stone1 :2:4 20mm graded aggregate) in precast posts, fencing posts, straining or terminal posts, struts etc, for fencing, average sectional area exc 100 sqcm and n.exc 250 Sqcm with or without chammfered angles and flat, splayed, rounded or mitred tops as directed and fixed etc. compete all as spd and directed.

Supply & Fix mild steel angles, bars, flats wind ties for roof including securing bolts, posts and struts in fencing etc including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting, etc. and similar work confirming to Fe-290 Gde E-165 complete.all as specified and directed.

Supply only PVC coated (1mm thick) chain link fencing exc 2.00 but n.exc 3.50 kg per sqm with size of mesh 50 x 50 mm and thickness of wire n.exc 2.83 mm all as specified and as directed.

Fixing only PVC coated chain link fencing including fixing of line wires any mesh, size and any type of standards, rails, straining bolts etc including provision of binding wires complete.(Supply of MS line wire and flat iron bolt & nuts measured and paid seperately)

Supply only 6mm dia wire PVC coated for support/line wire to chain link fencing complete.

Supply only mild steel bolts with hexagonal or square head one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut exc 5 cm long n.exc 10 cm long dia metre of neck exceeding 11 to 15 mm complete.

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of Fe-410-W (grade E-250) Quality B

M&L for applying two coats of cement base paint over a coat of primer on new plaster or untreated surfaces on walls incl preparation of wall surfaces all as specified

M&L for preparing new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces.

M&L for PCC 1:2:4 type B2, using 40mm graded aggregate of 100mm thick as in hardstanding and footpath.

M&L for 60mm thick coloured machine pressed precast concrete interlocking paver block glossy finished any size and shape conforming to IS 15658-2006 , M-35Grade with grey cement and pigment over sand filling complete all as directed.( Cost of Sand will be measured and paid separately)

M & L for Sand filling under floors or in foundations including watering and consolidation complte all as specified.

M & L for point wiring complete with single core multi stranded Copper conductor FRLS cable of size 1.5 sqmm PVC insulated unsheathed 1100 volt grade in and including PVC conduit suitable size including Tee junction bends etc concealed in wall/fixed on ceiling and PVC switch board hylam sheet of 3mm thick including M.S. sunken boards of suitable size for housing switched sockets etc including 1.5 sqmm. green PVC insulated wire for earth continuty.complete all as specified and as directed(a) One light point/Exhaust fan controlled by one way switch

Supply and fix of switch piano flush type single pole one way 5 Amp all as specified and directed.

Supply and fix ceiling rose surface baklite 65 x 50 mm 3 terminal, complete all as specfified and as directed.

Supply and fix energy efficient aluminium housing LED Smart bright batten 20/22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose all as specified and as diected.

S & F LED mirror light fitting 1 x 10 Watt provided with high output diffuser including high efficiency electronic driver complete with LED lamp, prewired upto connection block and connecting with three core PVC copper flexible cable of size 1.5 Sq.mm from ceiling rose to connector block, including taking down old unserviceable mirror light fitting of any wattage, complete all as specified and directed.

S&F Street light New genration energy saving & envoirmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs 35 w as light and electronic driver complete all as per with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete as directed.

Supply and fix exhaust fan steel body suitable for on working of AC 230 V ,50 Hz 300 mm sweep 1400 RPM,with heavy duty motor ,incl louvers complete all as specified

Supply and fix in repair metal enclosure distribution board SPN, 4 way 240 volts, with 100 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs complete all as as specified and as directed.

Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, all as specified and as directed.

Supply and fix MCB SPN 240 volts, 5 to 32 Amps, all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I

Supply, lay, test and commissioning under ground XLPE insulated and PVC sheathed, armoured heavy duty under ground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 2 Core 10 sq mm complete all as specified and directed.

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers,bends etc of size 50 mm OD and 38mm ID confirming to IS 14930 -II and ISI Marked all specified and directed.

Supply and fix 25 mm bore GI tubing medium grade laid in trenches / floor or fixed to wall in any length with screwed and socket joints together with all galvanised GI fitting such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc and pressure testing, washing out complete all as specified and directed

Supply and fix 25 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed, complete all as specified and as directed

M&L for cutting existing 40mm GI line and making branch connection of 25 mm dia GI line including fittings required for connection complete all as specified and directed

Supply and fix 25 mm bore Gun Metal gate valve with iron wheel head ISI Marked screwed both ends suitable for GI tubing complete all as specifed and directed

Supplying, hoisting and fixing rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of 1000 Litre capacity etc complete all as specified and directed.

M & L for RCC M 30 design Mix concrete as in walls and retaining walls any thickness size and shape including attached pilasters butt raisers all as specified and directed.

Use and waste of formwork to faces of walls / retaining wall abutments parapets and staircase rails and similar work including attachments pillasters, batters etc vertical or to batters.

Kailash Engineering Company

Gulmarg Electrical Service

M/S R R ENTERPRISES

M/s G K Enterprises

BHARAT MULTITECH INDUSTRIES PVT LTD

DHAKSHNA MOORTHY AND SON

MGP Enterprises