Supply, installation and commissioning of 04 nos. 16mtr Height, High Mast Tower including luminaries at Mohanpur OCP under Salanpur Area.

Amount

Supply of high mast tower should be suitable for a wind speed of 180Km/H, 16 mt height high mast from steel plate and continuously capered polygonal (at least 20 sides) cross section The entire mast should be hot dip galvanized and thickness of galvanization should not be less than 86 micron after fabrication internally in accordance with BS-739. The tower should be in two sections (each of length 8375 mm or top length 5470 mm and bottom length 10980), base dia & top dia should be - 410mm & 150mrn with telescopic slip joint, Size of opening door 1200 x 250 mm g antiwandalized type locking arrangement & 450 kg approx weight. All steel material used in construction of mast complies with BSEN- 10025 or equivalent appropriate rate and welding in accordance with BS:5135 & comprising with lighting finally and earthing terminal etc. The mast should be supplied with components including Head frame & pulley assembly, LED AOL, winch bracket, Lantern carriage ring for luminanes and C.G. box mtg.arms, resting bracket guide ring, compensating disc, Single spike lightening arrestor double drum type winch (capacity-SWL 750kg), lantern carriage stainless wire rope of required length and size grade AlS1316 with minimum 6 mm dia. steel wire rope shall be factory cut terminated for case of installation winch driving power tools (motor with hand held control, operating speed 410 rpm,2HP electric motor) 4 sqmm multi core flexible around copper cable, junction box ( weather proof cast aluminum) etc. including aviation lamp suitable lightning arrestor is provided on the top of the head frame cover at centre position and all other fitting accessories are made of stainless steel materials and from quality manufacturers (including loading, unloading at work site).

Foundation. testing and commissioning of above high mast tower of RCC foundation with M20 grade concrete considering SBC of soil at 10T/sq. mtr, at 2 mtr depth(l .25M x 1.25M x 1.50M) reinforced steel used in foundation 12mm tor at base and 16mm tor in pedestal as per direction.

Supply of 300 W, neutral white LED flood light complete with IP66 Ingress protection, 220 to 240V, 50Hz, Polycarbonate bowl/cover UV resistant, 190001m, 4000 CCT(K) (Philips/Bajaj/Wipro etc make)

Supplying fitting and fixing of feeder pillar box over all approx dimension 1.00M x 0.75M fabricated from 25mm thick MS plate including cernent concrete foundation etc. complete with prima circuit on/off of road light, including contractor, main switch/ MCB Electronics Timer Switch as require complete.

Earthing with 2 nos. of 50mm dia, 3 m long G.I. pipe (medium) including flat wire attached to the Mast structure at a convenience point with 12mrn dia stainless steel bolt as per GS

Supplying & laying of 4 core 25 sqmm armored aluminum cable in underground trench below 1.00 Mt from G.L. and mending good damages covering the same by filling with sand at least 0.05 mt, including cost of supply of sand, gland socket, etc as required ( Inclusive of incidental charges , etc.)

Labour charges of boring all kind of soil by auger boring horizontally also cost of withdrawal the same and laying in bore holes G.I./C.I. pipes etc. all complete.

Supplying laying of 65mrn dia G.l. pipes (TATA) for protection of PVC cable as per GS

Brick work with 1st class bricks in cement mortar (6.1) in foundation and plinth in ground floor

Cement concrete with graded stone ballast (20 mm size) including shuttering in ground floor(1:1.5:3) proportion as per relevant ISI code

Plaster (2 wall, floor, ceiling, etc.) with sand and cement mortar including rounding of concrete surface, Including throttling nosing and drip course where necessary (ground floor) 20mm thick plaster.

Priming one coat on timber, plastered or other metal surface with synthetic Enamel/ Oil bound primer of approved quality including smoothening surface by sand papering, etc

Painting with best quality synthetic enamel of approved make and brand including of approved putty, etc. On the surface, if necessary on steel or other metal surface (Two Coats with any shade except white)

Total impact of GST for the purpose of CTC

ELECTRO POWER INDUSTRIES (BID ID -1119405)

M/S AJAY ENTERPRISES (BID ID -1120366)