WBMAD/CM/DLK/NIT-25e/25-26

Surface dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed.

Earth work in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sand stone) including removing, spreading or stacking the spoils within a lead of 75m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1.500 mm. .

(b) Depth of excavation additional depth beyond 1,500 mm. and up to 3,000 mm. but not requiring shoring.

(B) Filling in foundation or plinth by Fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Brick work with 1st class bricks in cement mortar (1:4) (a) In foundation and plinth

(b) In superstructure, ground floor

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.a) Pakur Variety

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.(i) Pakur Variety

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor). (When the height of a particular floor is more than 4 m the equivalent floor height shall be taken as 4 m and extra for works beyond the initial 4 m ht. shall be allowed under 12 (e) for every 4 m or part thereof) (a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For works in foundation and upto roof of ground floor/upto 4 m

25mm. thick damp proof course with cement concrete with stone chips (1:1.5:3) [with graded stone aggregate 10 mm nominal size] and admixture of water proofing compound as per manufacturer's specification followed by two coat of polymer based paint, (1st coat after 4 to 5 days of concrete laying and 2 nd coat just before brick masonry work) as directed (cost of water proofing compound & polymer based paint to be paid separately).( Chequering not required over concrete or painted surface). [Note: - Waterproofing as per item 9, polymer based paint as per item 8 (a) of subhead C of Section (C).

Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches

Supplying, fitting and fixing Black Stone slab used in Kitchen slab, alcove, wardrobe etc. laid and jointed with necessary adhesive Cement mortar (1:2) including grinding or polishing as per direction of Engineer-in -Charge in Ground Floor. (For Distribution Cum Kitchen Area)

(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. (Add extra @ 1% for each addl. floor upto 4th floor and @ 1.25% for each addl. floor above 4th floor)-(i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.(Avg=13 kg /Sqm)

Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (a) Fixed type steel windows as per IS sizes with horizontal glazing bars.

Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (b) Openable steel windows as per IS sizes with side hung shutters and horizontal glazing bars..

Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall)

Extra

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. (ii) 40 mm thick shutters with 19 mm thick panel of size 30 to 45 cmm In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made)-(b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

Wood work in door and window frame fitted and fixed in position complet including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals).(c) Sal : Siliguri-Note: Extra for Lifting Charges for each additional floor, i) Rs. 200/- per Cu.m (upto 4th floor)

Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)- (c) 40mm X 6mm, 125mm Length

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark.

Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge. In ground floor. (D3)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (a) 15 mm thick plaster

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (a) On timber or plastered surface : With other than hi-gloss of approved quality- (iv) Two coats (with any shade except white)

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : In Ground floor (Two Coat) (b) On steel or other metal surface : With other than hi-gloss of approved quality (iv) Two coats (with any shade except white)

Supplying, fitting and fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sqm (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapezoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia and 3 mm thick washer etc. complete with 150 mm end lap and one corrugation minimum side lap (Payement to be made on area of finished work) -(i) In Roof:- a) With 0.50 mm thick sheet

Aluminium sheet ridging fitted with self tapping screws, EPDM washers etc complete.(Minimum 225mm end lapping) (A) 300 mm lapping each way- (a) With 0.71 mm sheet

Galvanised iron sheets valley gutter with perimeter not less than 750 mm with 225 mm lap each way fitted and fixed with necessary bolts, nuts, screws, etc.complete. Valley gutter made of 0.63 mm. thick sheets. (300mm End lapping)

Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor) (ii) In wall:- a) With 0.60 mm thick sheet

M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete. Payment to be made on the basis of calculated weight of structural memebrs of MS Holow Section as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a hight of erection 8 m. / 2nd floor level from the ground. Add 1.5 % extra over the rate for each additional floor or 4m. beyond the initial 8 m. or part thereof.

Drilling holes of requisite diameter in R.S. joists channels, tees. Plates etc (a) (I) Dia. Upto 12mm and depth upto 10 mm.

Holding down bolt with nut including 100 x 100 x 6 mm plate washer at bottom fitted complete and packing the hole with cement concrete or cement grout as directed.(ii) 20 mm dia bolt.-(c) 600 mm long

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (A) Floor-With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.-(a) Area of each tile upto 0.09 Sq.m-(ii) Other than Coloured decorative including white.

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (B) Wall-With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.-(a) Area of each tile upto 0.09 Sq.m-(ii) Other than Coloured decorative including white.

Nilkamal Mega 4 Seater Dining Set

M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. (ii) Grill weighing above 16 Kg./sq.mtr and above

Supplying 1.5mm thick M.S. sheet fitted and fixed on one or both faces of M.S./ W.I. gate etc. with point welding at not more than 150mm apart complete in all respect as per design including cost of all labour and materials

Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia. (SAIL/TATA/RINL)

Supply & Fixing 240 V, 32 A. D.P. Sheet steel main switch on angle / flat iron frame on wall with earthing attachment as per G.S. ( Havells make.) [ Near Service point ] [ PWD. P – D-1 / I –1.a ]

Supply & drawing 1.1 Kv. Grade 2x 56/0.3 ( 4.0 Sq.mm ) + 1 x 36/0.3 ( 2.5 Sq.mm ) single core stranded FR PVC insulated & sheathed copper wire ( Brand approved by EIC ) in 20 mm. dia. PVC rigid conduit ( Precision make ) incl. necy. fittings as required. ( For Supply line & Main switch to SPN.D.B ) as per G.S [ PWD. P- E-14 / - 1.a ]

Supply & fixing double door SPN.MCB D>B with IP-42/43 protection , concealed in wall after cutting the wall & mending good the damages to original finish incl. inter – connection with suitable size of copper wire and neutral link & provision for earthing for 2 + 6 way BDB ( Havells make ) [ PWD. P- D-9 / I – 13 ) [ 3-Ckts for Dinning Room & 2 – Ckts for Kitchen , store & bath )

S & F 240 V MCB of breaking capacity 10KA & characteristics on din rail and necy. connection 6- 10 A .S.P.M.C.B. as per G.S ( PWD P- D-6 /I-7 ) [ Havells make ]

S & F 240 V , 40 Amp. MCB. Isolator on Din rail and necy. connection as per G.S. [ PWD P- D-5 /I- 6 ] Havells make ]

Distribution wiring in 22/ 0.3 ( 1.5 sq.mm ) single core stranded FR.PVC. insulated & unsheathed copper wire ( brand approved by EIC ) in 20 mm size PVC rigid conduit ( Precision make ) with 1x22/0.3 ( 1.5 Sq.mm ) single core stranded FR.PVC. insulated & sheathed copper wire for ECC to light , fan points etc. with piano key type switch ( Anchor make ) fixed on M.S. CRC sheet metal ( 16 SWG ) switch board cum JB on wall complete with 2 no's suitable size PH & N copper bar incl. bakelite ( wall matching colour ) top cover of 3 mm. thick and incl. 175 mm x 100 mm x 65 mm inspection box making earthing attachment , painting the M.S. Boxb and mending good the damages to original finish. ( Average Run – 6 mts. ) [ PWD . P- E-14 / I – 2 ]

Distribution wiring in 22/ 0.3 ( 1.5 sq.mm ) single core stranded FR.PVC. insulated & unsheathed copper wire ( brand approved by EIC ) in 20 mm size PVC rigid conduit ( Precision make ) with 1x22/0.3 ( 1.5 Sq.mm ) single core stranded FR.PVC. insulated & sheathed copper wire as ECC to 6 A , 3 pin flush type plug socket & Piano key Type switch ( Anchor make ) fixed on M.S. CRC sheet metal ( 16 SWG ) switch board cum JB on wall complete with 2 no's suitable size PH & N copper bar incl. bakelite ( wall matching colour ) top cover of 3 mm. thick and incl. 175 mm x 100 mm x 65 mm inspection box making earthing attachment , painting the M.S. Boxb and mending good the damages to original finish. A. ( On Board )

B. 3.0 mts. [ PWD . P- E-15 / I – 4 ]

S & fixing LED batten Tube Light fittings complete ( Philip’s make . Model – TMC-501P-1xT-22 watt P3241 ) fitted on wall /ceiling as per direction of E.I.C. [18+4 =22 Nos.] Rate: Rs.451.00 + 86.00 = Rs.537.00 [ I & WD . P-113 ]+[ PWD -P- C-2 /I-14.a ]

S & Fixing 250 V. A.C. ceiling fan of ( Crompton / Bajaj / Havells -make ) of 1200 mm. sweep . Model – Cool Breeze , Brown colour complete set incl. fixing only ceiling complete with blades , canopy , fork , rubber bush etc. with 30 cm. down rod incl. painting and necy. connection by copper wire as per direction of E.I.C. [ UD & MA Pg-23;70 ] + [PWD – P- C-3 /I- 21.a.] Rate: 2283.00 + 66.00 = 2349.00

S & Fixing socket type fan regulato ( Step type ) [Brand approved by EIC ] on existing sheet metal board incl. making connection etc. as per G.S. [ PWD. P- E-6 /I- 18.b]

S & F bulk head light fittings ( Havells make ) with die cast aluminium housing & frosted glass on wall incl. S & F 8 watt LED lamp complete set. [ 1- Kitchen + 1 – Toilet ] ( PWD. P- D-13 / I – 23 ) Rate: 579.00 + 75.00 = 654.00

S & F 230 V. Metal Exhaust Fan – 12 “ (300 mm ) sweep single phase complete with all accessories incl. louver shutter ( Model – Crompton / Havells / Bajaj make ) – Trans Air . [ For Kitchen only ] [ UD & MA .P- 14 / I – 5]

S & F 230 V. Metal Exhaust Fan – 9 “ (300 mm ) sweep single phase complete with all accessories incl. louver shutte( Model – Crompton / Havells / Bajaj make ) – Trans Air . [ For Kitchen only ] [ UD & MA .P- 14 / I – 6]

Fixing only exhaust fan after making hole in wall and mending good the damages and net cement finish etc. as practicable as possible and providing necy. length of PVC. Copper wire and making connection of 12 “sweep Exhaust fan. [ PWD.P- C-4 / I – 28.b.]

Fixing only exhaust fan after making hole in wall and mending good the damages and net cement finish etc. as practicable as possible and providing necy. length of PVC. Copper wire and making connection of 9 “sweep Exhaust fan. [ PWD.P- C-4 / I – 28.b.]

S & Fixing >5 Ltr. Water purifier. RO = UV + UF +TDS Water Purifier ( White , Blue ) complete set. Fitted on wall as per direction of E.I.C. [ Make- Kent/Aquaguard/Pureit ]

Supply & installation water pump 220/240 V. 1 H.P. residential water pump self-priming single phase , high suction capacity , wide voltage range, line connection etc. complete set. ( Crompton/KSB make ) UDMA Pg-44;34

Supply Delivery and installation of ABC Powder type fire extinguishers (stored pressure) HSN code-84241000 conforming to IS:15683 and complete in all respect as per direction of EIC 06 Kg with ISI marked Mono Ammonium Phosphate base ABC power conforming to IS:14609 and pressurized with nitrogen gas. Suitable for operating between (-)30ºC to (+)55ºC. Fire rating -2A & 21B [UDMA Pg-23;77]

Supply, Delivery and installation of Co2 type fire extinguishers: HSN code-84241000 4.5 Kg capacity with ISI marked Co2 type fire extinguisher squeeze grip type conforming to IS:15683:2006 made from seamless cylinder conforming to IS:7285 duly approved by Chief controller of explosive, Nagpur, fitted with ISI marked controller of explosive, Nagpur, fittet with ISI marked controlled valve conforming to IS:3224, high pressure 1 mtr. long discharge hose and horn complete with initial gas charged with carrying handle and wall mounting bracket suitable for operating between (-)30ºC to (+)55ºC. Fire rating -13B. [UDMA Pg-24;78]

Earthing with 50 mm. dia. ISI make -Medium gauge G.I. pipe of 3.04 mts. Length x 3.64 mm. thick and 1 x 14 SWG G.I. Hot Dip wire ( 4 Mts long ) with necy. items for earthing works as per PWD. Schedule .[ PWD . P- G-1 / I – 2.a ]