Development and Maintenance of Parks with Open-Air Gyms in Karnal call 5

Amount

Development of Sector 14 Park

Taking out existing CC interlocking paver blocks from footpath/ central verge,including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking theexcavated soil, clear from the edge of excavation andsubsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc.as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin-charge)

Providing and Laying of plain Cement Concrete in Foundation of Kerb / levelling course including centering and shuttering but excluding reinforcement all complete as per drg. and MORT&H specifications sections 1500, 1700 and 2100 complete as per drawing and direction Engineer-in-charge.

Providing and applying two coats of synthetic enamel paint including primer to kerb surfaces etc. complete as per MORT&H Specifications clause 803 complete as per drawing and direction Engineer-in-charge.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per MORT&H Specifications Clause 401 (Grading–I of Table–400-1) and complete as per drawing and direction Engineer-in-charge.

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per MORT&H Specifications Clause 406 and complete as per drawing and direction Engineer-in-charge.

75 mm thick filling of Morrum for pathway including supplying of required materials and consolidation etc. complete as per drawing and direction of engineer-in-charge

Providing and laying factory made chamfered edge M-35 Grade 60mm Thick Cement Concrete paver blocks in footpath, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 30mm thick compacted bed of sand,compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern,finishing and sweeping extra sand. complete as per drawing and direction Engineer-in-charge.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) complete as per drawing and direction Engineer-in-charge.: 25mm Thick

Cement Concrete 1:4:8 with stone aggregate 40mm nominal size in foundation and plinth complete as per drawing and direction Engineer-in-charge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m complete as per drawing and direction Engineer-in-charge.

Providing, laying and fixing 30mm thick Stone Lining complete in all respect as per drawing and direction Engineer-in-charge.

Providing, laying and fixing MS Vertical Pole for Volley Ball Court including foundation complete in all respect as per drawing and direction Engineer-in-charge.

Providing, laying and fixing MS Vertical Pole for Badminton Court including foundation complete in all respect as per drawing and direction Engineer-in-charge.

Providing and fixing Volley Ball Net of standard size with high tensile strength complete as per standard, as per drawing and direction Engineer-in-charge.

Providing and fixing Badminton Net of standard size complete as per standard, as per drawing and direction Engineer-in-charge.

Providing and fixing RCC Modern Park Bench complete as per standard, as per drawing and direction Engineer-in-charge.

Planting shurb including planting with manure, gardening and maintenance complete as per drawing and direction Engineer-in-charge. TABERNAEMONTANA DWARF

Planting shurb including planting with manure, gardening and maintenance complete as per drawing and direction Engineer-in-charge. CUPHEA HYSSOPIFOLIA

Planting shurb including planting with manure, gardening and maintenance complete as per drawing and direction Engineer-in-charge.DURANTA

Electrical Pole Led Light (5m Height) @20 C/C with Solar Panel A 24 watt solar street LED light as techinical specification and as per direction of Engineer-in-Charge

Manufacturing, supplying and fixing retro reflective sign boards made up of 2mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheetingconforming to type - XI of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2012, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriatepriming coat including all leads and lifts etc. complete as per drawing , MORT&H Specifications Clause 801 and direction of Engineer-in-charge. Mandatory/ Regulatory sign boards of 900 mm diametre with support length

Air Walker -Providing, designing and fixing of Air Walker of size 992 x 505 x 1380 mm fabricated with mainpost of 140mm dia and 3.00 mm thick Swing leg is dia 48 mm thickness 2.75mm, Handle beam is dia 42 mm thickness 2.75mm , and other pipes of 2.75 mm thick having bottom plate 260 mm dia with thickness 12.00 mm ith ABS Cap/ Cover, all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasingtreatment and Sand Blasting De -rusting treatment mustbe used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 90 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Foothold shall be made up of steel 3.00 mm thick Nylon 4.00 mm thick, with rounded edges to prevent any impact of injury and welded/ attached to main structure for vandalism proof design and long life. Bearing No 6205 used shall be maintenance free, duly oil sealed and self lubricated made by reputed company. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by Steel/ LLDPE caps for ser safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J-bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover

Air Swing Providing and Fixing of AIR SWING Emphasizes on the front & back upper leg muscles exercise. Size1400× 915× 1360mm main post made of 4 inch pipe and other main pipes 1-1/2 inch pipes. 3mm thickness pipes Double coated P U Painting, heavy duty sealed ball bearing, for long lasting life. Rate including cost of all materials and labour charges including civil (foundation) works etc complete

Push Up AndDip Bar-Providing, designing and fixing of exercising bar in a pair of size 1802 x 612 x 1399 mm fabricated with main post of 140 mm dia and 3.00 mm thick and rest of the pipes 2.75 mm thick Yellow sleeve is dia 159mm thickness 8.00 mm, Parallel Bar dia 42 mm 2.75mm, rest pipe is thickness 2.75mm, having bottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover. all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De -rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 80 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J -bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover,

Waist Trainer-Providing, designing and fixing twister of size: 1365× 1708 x 1292 mm fabricated with main post of 140 mm dia and 3.00 mm thick and rest of the pipe 2.75mm, Yellow sleeve dia 159mm thickness 8.0mm,Handle beam is dia 33 thickness 2.75mm, Under plate pipe is dia 48 mm thickness 2.75mm, having bottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover , all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De-rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 90 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Foothold shall be made up of steel 4.00 mm thick , with rounded edges to prevent any impact of injury and welded/attached to main structure for vandalism proof design and long life. Bearing No 6205 used shall be maintenance free,duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by Steel/LLDPE caps for user safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630.The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M-25 with J-bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover,

The main frame of Leg Stretcher hall consist of 80 NB G.I. pipes with two suitably designed brackets attached on it. Brackets have to be made of M.S. material with G.I. plating. The moving frame of Leg Press is to be made of 40NB G.I. pipes which is to be mounted to the main frame with the help of suitably designed, machined shaft and bearing housing. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. Foot rest is to be hinged to the main frame with the help of suitably designed G.I. plated clamp and 25 NB G.I. pipes. Gusset plates have to be provided to give extra strength to foot rest. Foot rest is to made of high quality HDPE material. Suitably designed HDPE pads has to be provided at the bottom of moving frame. Seat and back rest provided has to be made of HDPE.. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe is to be close by GI / HDPE caps for user safety against entrapment.

Sit Up Board-Providing, designing and fixing of single sit -up station of size 1504 x 1133 x 624 mm fabricated with main post of 140 mm dia and 3.00 mm thick ,Yellow sleeve dia 159 mm thickness 8.0mm, Connecting pipe dia 33 mm thickness 3.0mm and rest of the pipes are 2.75 mm thick,having bottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover,all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De - rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 90 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat shall be made up of steel pipe 2.75mm thick , with rounded edges to prevent any impact of injury and welded/ attached to main structure for vandalism proof design and long life. All open ends of pipe to be closed by Steel/ LLDPE caps for user safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J -bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover. 8 Exercising Bar:

The main frame of SKY MAchine is to be made in two parts, one from 80NB & 40NB Galvanized pipe & vertical pipe with 80NB pipe structure. The handle pipe is to be of 25NB GI pipes with PVC/rubber grip on top end. This handle pipes is to be hinged over 80NB main frame with the help of suitably designed heavy duty bearings assembly. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. The handle pipe is to be further extended to the rectangular tube of 50 x 50 mm on both sides with 40NB galvanized pipe links. Paired rectangular tubes with four foot rests has to be linked to main frame. Foot rest is to be made with the help of high quality Aluminium Casting material. The total structure is to be supported on Foundation stand which shall be of 80NB pipe. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be closed by GI / PVC caps for user safety against entrapment.

Horse Rider Station: Providing, designing and fixing of horse rider station of size 1000 x 600 x 1100 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Stair Stepper: Providing, designing and fixing of stair stepper in a combination of pair and a single step of size 1000 x 800 x 1400 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Pull Chair: Providing, designing and fixing of Pull pair of size 2500 X 800 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber at top end. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Seated Chest Press :- Providing, designing and fixing Seated Chest Press of Pull pair of size 1800 X 700 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Arm Wheel :- Providing, designing and fixing Arm Wheel in a pair of size 850 X 800 X 1800 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Elliptical Exerciser :- Providing, designing and fixing Elliptical Exerciser of size 1200 X 540 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Rowing Machine :- Providing, designing and fixing Rowing Machine of size 1280 X 800 X 1500 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Foothold shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The

Supply and fixing of Swings (5.83*4.0*6.66)- Plate form height above ground 2.0 to 2.5 m. The chain link should be plastic coated and take the load of80 kg.The Assy. Of swing has to be heavy duly ball bearing. With structural parts GI Pipes and MS Steel (including cutting,fitting, welding, bolting and smooth grinding etc.) complete.All the structural parts shall be polyester power coatedhaving minimum thickness of 50 micron.High quality fastened complete with supply/fixing andinstalled to be ground including civil work for making baseand pedestals.For safety of children sand bed with the minimum thicknessof 200 mm should be made in safe play by the vendor.

Supply and fixing of Straight Slide -Slider should be made of Mat. HDPE (Pipe) of ID 40 & OD 50 with nylon bush (mat finish) of demanded colour. With structural parts GI Pipes and MS steel (including cutting, fitting, welding, Bolting and smooth grinding etc. complete. All the structural parts shall be polyester powder coated having min. Thickness of 50 micron. High quality fastened complete with supply/fixing and installation to ground including civil work for making base and pedestals

Supply and fixing of See - Saw- Safe play area=1.0 to 1.5m*3.0 to 3.6m Sitting area should be coated with polyester fibre glass reinforced plastic (of 6 to 8 mm thickness). For structural parts GI Pipes and MS Steel (including cutting, fitting, welding, bolting, bearing and smooth grinding etc. ) complete. All the structural parts shall be polyester powder coated having min. Thickness of 50 micron. The structural parts should not to be painted, For structural parts stainless steel should be used. Nowhere Iron to be used Entire product is assembled with nut bolts, flanges and couplings. High quality fastened complete with supply/fixing and installed to be ground including civil work for making base and pedestals.

Maintenance of hardscape (paved area, pathway etc.), softscape and Plantation / Hoirticulture Works including Cleaning of all hardscape and softscape area, Maintenance of lawn/ herbs/ shrubs/ climbers etc.; Watering, weeding, cleaning, mulching, cutting etc.; Apply compost and organic fertilizers, Applying pesticides and insecticides; Disposal of dry and fallen leaves etc.; painting of kerb stone, mainteneance of all civil works electrical components etc. Total Cost for Operation & Maintenance for 60 months @ 0.25% per month to a total of 15% of the Total Cost

Development of City Park Sector 12

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc.as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer in-charge).

Providing and Laying of plain Cement Concrete in Foundation of Kerb / levelling course including centering and shuttering but excluding reinforcement all complete as per drg. and MORT&H specifications sections 1500, 1700 and 2100 complete as per drawing and direction Engineer-in-charge.

Providing and applying two coats of synthetic enamel paint including primer to kerb surfaces etc. complete as per MORT&H Specifications clause 803 complete as per drawing and direction Engineer-in-charge.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per MORT&H Specifications Clause 401 (Grading–I of Table–400-1) and complete as per drawing and direction Engineer-in-charge.

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per MORT&H Specifications Clause 406 and complete as per drawing and direction Engineer-in-charge.

75 mm thick filling of Morrum for pathway including supplying of required materials and consolidation etc. complete as per drawing and direction of engineer-in-charge

Providing and laying factory made chamfered edge M-35 Grade 60mm Thick Cement Concrete paver blocks in footpath, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 30mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete as per drawing and direction Engineer-in-charge.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) complete as per drawing and direction Engineer-in-charge.: 25mm Thick

Cement Concrete 1:4:8 with stone aggregate 40mm nominal size in foundation and plinth complete as per drawing and direction Engineer-in-charge.

Providing, laying and fixing 30mm thick Stone Lining complete in all respect as per drawing and direction Engineer-in-charge.

Providing, laying and fixing MS Vertical Pole for Volley Ball Court including foundation complete in all respect as per drawing and direction Engineer-in-charge.

Providing, laying and fixing MS Vertical Pole for Badminton Court including foundation complete in all respect as per drawing and direction Engineer-in-charge.

Providing and fixing Volley Ball Net of standard size with high tensile strength complete as per standard, as per drawing and direction Engineer-in-charge.

Providing and fixing Badminton Net of standard size complete as per standard, as per drawing and direction Engineer-in-charge.

Providing and fixing RCC Modern Park Bench complete as per standard, as per drawing and direction Engineer-in-charge.

Electrical Pole Led Light (5m Height) @20 C/C with Solar Panel A 24 watt solar street LED light as techinical specification and as per direction of Engineer-in-Charge

Manufacturing, supplying and fixing retro reflective sign boards made up of 2mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheetingconforming to type - XI of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2012, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriatepriming coat including all leads and lifts etc. complete as per drawing , MORT&H Specifications Clause 801 and direction of Engineer-in-charge. Mandatory/ Regulatory sign boards of 900 mm diametre with support length Mandatory/ Regulatory sign boards of 900 mm diametre with support length

Air Walker -Providing, designing and fixing of Air Walker of size 992 x 505 x 1380 mm fabricated with mainpost of 140mm dia and 3.00 mm thickSwing leg is dia 48 mm thickness 2.75mm, Handle beam is dia 42 mmthickness 2.75mm , and other pipes of 2.75 mm thick having bottom plate 260 mm dia with thickness 12.00 mm ith ABS Cap/ Cover, all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasingtreatment and Sand Blasting De -rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 90 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Foothold shall be made up of steel 3.00 mm thick Nylon 4.00 mm thick, with rounded edges to prevent any impact of injury and welded/ attached to main structure for vandalism proof design and long life. Bearing No 6205 used shall be maintenance free, duly oil sealed and self lubricated made by reputed company. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by Steel/ LLDPE caps for ser safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J-bolts and when concrete is set, fixing the equipment on to it and cover nuts and boltswith base plate cover

Air Swing Providing and Fixing of AIR SWING Emphasizes on the front & back upper leg muscles exercise. Size1400× 915× 1360mm main post made of 4 inch pipe and other main pipes 1-1/2 inch pipes. 3mm thickness pipes Double coated P U Painting, heavy duty sealed ball bearing, for long lasting life. Rate including cost of all materials and labour charges including civil (foundation) works etc complete

Push Up And Dip Bar-Providing, designing and fixing of exercising bar in a pair of size 1802 x 612 x 1399 mm fabricated with main post of 140 mm dia and 3.00 mm thick and rest of the pipes 2.75 mm thickYellow sleeve is dia 159mm thickness 8.00 mm, Parallel Bar dia 42 mm 2.75mm, rest pipe is thickness 2.75mm, havingbottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover. all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De -rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 80 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J -bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover,

Waist Trainer-Providing, designing and fixing twister of size: 1365× 1708 x 1292 mm fabricated with main post of 140 mm dia and 3.00 mm thick and rest of the pipe 2.75mm, Yellow sleeve dia 159mm thickness 8.0mm,Handle beam is dia 33 thickness 2.75mm, Under plate pipe is dia 48 mm thickness 2.75mm, having bottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover , all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De-rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 90 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Foothold shall be made up of steel 4.00 mm thick , with rounded edges to prevent any impact of injury and welded/attached to main structure for vandalism proof design and long life. Bearing No 6205 used shall be maintenance free,duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by Steel/LLDPE caps for user safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630.The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M-25 with J-bolts and when concrete is set, fixing the equipment on to it and cover nuts and boltswith base plate cover,

The main frame of Leg Stretcher hall consist of 80 NB G.I. pipes with two suitably designed brackets attached on it. Brackets have to be made of M.S. material with G.I. plating. The moving frame of Leg Press is to be made of 40NB G.I. pipes which is to be mounted to the main frame with the help of suitably designed, machined shaft and bearing housing. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. Foot rest is to be hinged to the main frame with the help of suitably designed G.I. plated clamp and 25 NB G.I. pipes. Gusset plates have to be provided to give extra strength to foot rest. Foot rest is to made of high quality HDPE material. Suitably designed HDPE pads has to be provided at the bottom of moving frame. Seat and back rest provided has to be made of HDPE.. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe is to be close by GI / HDPE caps for user safety against entrapment.

Sit Up Board-Providing, designing and fixing of single sit -up station of size 1504 x 1133 x 624 mm fabricated with main post of 140 mm dia and 3.00 mm thick ,Yellow sleeve dia 159 mm thickness 8.0mm, Connecting pipe dia 33 mm thickness 3.0mm and rest of the pipes are 2.75 mm thick,having bottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover,all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De - rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 90 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat shall be made up of steel pipe 2.75mm thick , with rounded edges to prevent any impact of injury and welded/ attached to main structure for vandalism proof design and long life. All open ends of pipe to be closed by Steel/ LLDPE caps for user safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J -bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover. 8 Exercising Bar:

The main frame of SKY Machine is to be made in two parts, one from 80NB & 40NB Galvanized pipe & vertical pipe with 80NB pipe structure. The handle pipe is to be of 25NB GI pipes with PVC/rubber grip on top end. This handle pipes is to be hinged over 80NB main frame with the help of suitably designed heavy duty bearings assembly. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. The handle pipe is to be further extended to the rectangular tube of 50 x 50 mm on both sides with 40NB galvanized pipe links. Paired rectangular tubes with four foot rests has to be linked to main frame. Foot rest is to be made with the help of high quality Aluminium Casting material. The total structure is to be supported on Foundation stand which shall be of 80NB pipe. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be closed by GI / PVC caps for user safety against entrapment.

Horse Rider Station: Providing, designing and fixing of horse rider station of size 1000 x 600 x 1100 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Stair Stepper: Providing, designing and fixing of stair stepper in a combination of pair and a single step of size 1000 x 800 x 1400 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Pull Chair: Providing, designing and fixing of Pull pair of size 2500 X 800 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber at top end. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Seated Chest Press :- Providing, designing and fixing Seated Chest Press of Pull pair of size 1800 X 700 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Arm Wheel :- Providing, designing and fixing Arm Wheel in a pair of size 850 X 800 X 1800 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Elliptical Exerciser :- Providing, designing and fixing Elliptical Exerciser of size 1200 X 540 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Rowing Machine :- Providing, designing and fixing Rowing Machine of size 1280 X 800 X 1500 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Foothold shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The

Supply and fixing of Swings (5.83*4.0*6.66)- Plate form height above ground 2.0 to 2.5 m. The chain link should be plastic coated and take the load of80 kg.The Assy. Of swing has to be heavy duly ball bearing. With structural parts GI Pipes and MS Steel (including cutting,fitting, welding, bolting and smooth grinding etc.) complete.All the structural parts shall be polyester power coatedhaving minimum thickness of 50 micron.High quality fastened complete with supply/fixing andinstalled to be ground including civil work for making baseand pedestals.For safety of children sand bed with the minimum thicknessof 200 mm should be made in safe play by the vendor.

Supply and fixing of Straight Slide -Slider should be made of Mat. HDPE (Pipe) of ID 40 & OD 50 with nylon bush (mat finish) of demanded colour. With structural parts GI Pipes and MS steel (including cutting, fitting, welding, Bolting and smooth grinding etc. complete. All the structural parts shall be polyester powder coated having min. Thickness of 50 micron. High quality fastened complete with supply/fixing and installation to ground including civil work for making base and pedestals

Supply and fixing of See - Saw- Safe play area=1.0 to 1.5m*3.0 to 3.6m Sitting area should be coated with polyester fibre glass reinforced plastic (of 6 to 8 mm thickness). For structural parts GI Pipes and MS Steel (including cutting, fitting, welding, bolting, bearing and smooth grinding etc.) complete. All the structural parts shall be polyester powder coated having min. Thickness of 50 micron. The structural parts should not to be painted, For structural parts stainless steel should be used. Nowhere Iron to be used Entire product is assembled with nut bolts, flanges and couplings. High quality fastened complete with supply/fixing and installed to be ground including civil work for making base and peadestals.

Maintenance of hardscape (paved area, pathway etc.), softscape and Plantation / Hoirticulture Works including Cleaning of all hardscape and softscape area, Maintenance of lawn/ herbs/ shrubs/ climbers etc.; Watering, weeding, cleaning, mulching, cutting etc.; Apply compost and organic fertilizers, Applying pesticides and insecticides; Disposal of dry and fallen leaves etc.; painting of kerb stone, mainteneance of all civil works electrical components. Total Cost for Operation & Maintenance for 60 months @ 0.25% per month to a total of 15% of the Total Cost

Development of Saini Colony Park

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc.as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin-Charge)

Providing and Laying of plain Cement Concrete in Foundation of Kerb / levelling course including centering and shuttering but excluding reinforcement all complete as per drg. and MORT&H specifications sections 1500, 1700 and 2100 complete as per drawing and direction Engineer-in-charge.

Providing and applying two coats of synthetic enamel paint including primer to kerb surfaces etc. complete as per MORT&H Specifications clause 803 complete as per drawing and direction Engineer-in-charge.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per MORT&H Specifications Clause 401 (Grading–I of Table–400-1) and complete as per drawing and direction Engineer-in-charge.

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per MORT&H Specifications Clause 406 and complete as per drawing and direction Engineer-in-charge.

75 mm thick filling of Morrum for pathway including supplying of required materials and consolidation etc. complete as per drawing and direction of engineer-in-charge

Providing and laying factory made chamfered edge M-35 Grade 60mm Thick Cement Concrete paver blocks in footpath, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 30mm thick compacted bed of sand,compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern,finishing and sweeping extra sand. complete as per drawing and direction Engineer-in-charge.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) complete as per drawing and direction Engineer-in-charge.: 25mm Thick

Cement Concrete 1:4:8 with stone aggregate 40mm nominal size in foundation and plinth complete as per drawing and direction Engineer-in-charge.

Providing, laying and fixing MS Vertical Pole for Volley Ball Court including foundation complete in all respect as per drawing and direction Engineer-in-charge.

Providing, laying and fixing MS Vertical Pole for Badminton Court including foundation complete in all respect as per drawing and direction Engineer-in-charge.

Providing and fixing Volley Ball Net of standard size with high tensile strength complete as per standard, as per drawing and direction Engineer-in-charge.

Providing and fixing Badminton Net of standard size complete as per standard, as per drawing and direction Engineer-in-charge.

Providing and fixing RCC Modern Park Bench complete as per standard, as per drawing and direction Engineer-in-charge.

Planting shurb including planting with manure, gardening and maintenance complete as per drawing and direction Engineer-in-charge. TABERNAEMONTANA DWARF

Planting shurb including planting with manure, gardening and maintenance complete as per drawing and direction Engineer-in-charge.CUPHEA HYSSOPIFOLIA

Planting shurb including planting with manure, gardening and maintenance complete as per drawing and direction Engineer-in-charge. DURANTA

Electrical Pole Led Light (5m Height) @20 C/C with Solar Panel A 24 watt solar street LED light as techinical specification and as per direction of Engineer-in-Charge

Manufacturing, supplying and fixing retro reflective sign boards made up of 2mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheetingconforming to type - XI of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2012, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriatepriming coat including all leads and lifts etc. complete as per drawing , MORT&H Specifications Clause 801 and direction of Engineer-in-charge. Mandatory/ Regulatory sign boards of 900 mm diametre with support length

Air Walker -Providing, designing and fixing of Air Walker of size 992 x 505 x 1380 mm fabricated with main post of 140mm dia and 3.00 mm thick Swing leg is dia 48 mm thickness 2.75mm, Handle beam is dia 42 mmthickness 2.75mm , and other pipes of 2.75 mm thick having bottom plate 260 mm dia with thickness 12.00 mm ith ABS Cap/ Cover, all pipes made up of hot rolled Tubular steel and pre galvanized, having Oil degreasingtreatment and Sand Blasting De -rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 90 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Foothold shall be made up of steel 3.00 mm thick Nylon 4.00 mm thick, with rounded edges to prevent any impact of injury and welded/ attached to main structure for vandalism proof design and long life. Bearing No 6205 used shall be maintenance free, duly oil sealed and self lubricated made by reputed company. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by Steel/ LLDPE caps for ser safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J-bolts and when concrete is set, fixing the equipment on to it and cover nuts and boltswith base plate cover

Air Swing Providing and Fixing of AIR SWING Emphasizes on the front & back upper leg muscles exercise. Size1400× 915× 1360mm main post made of 4 inch pipe and other main pipes 1-1/2 inch pipes. 3mm thickness pipes Double coated P U Painting, heavy duty sealed ball bearing, for long lasting life. Rate including cost of all materials and labour charges including civil (foundation) works etc complete

Push Up AndDip Bar-Providing, designing and fixing of exercising bar in a pair of size 1802 x 612 x 1399 mm fabricated with main post of 140 mm dia and 3.00 mm thick and rest of the pipes 2.75 mm thickYellow sleeve is dia 159mm thickness 8.00 mm, Parallel Bar dia 42 mm 2.75mm, rest pipe is thickness 2.75mm, havingbottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover. all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De -rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 80 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J -bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover,

Waist Trainer-Providing, designing and fixing twister of size: 1365× 1708 x 1292 mm fabricated with main post of 140 mm dia and 3.00 mm thick and rest of the pipe 2.75mm, Yellow sleeve dia 159mm thickness 8.0mm,Handle beam is dia 33 thickness 2.75mm, Under plate pipe is dia 48 mm thickness 2.75mm, having bottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover , all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De-rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 90 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Foothold shall be made up of steel 4.00 mm thick , with rounded edges to prevent any impact of injury and welded/attached to main structure for vandalism proof design and long life. Bearing No 6205 used shall be maintenance free,duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by Steel/LLDPE caps for user safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630.The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M-25 with J-bolts and when concrete is set, fixing the equipment on to it and cover nuts and boltswith base plate cover,

The main frame of Leg Stretcher hall consist of 80 NB G.I. pipes with two suitably designed brackets attached on it. Brackets have to be made of M.S. material with G.I. plating. The moving frame of Leg Press is to be made of 40NB G.I. pipes which is to be mounted to the main frame with the help of suitably designed, machined shaft and bearing housing. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. Foot rest is to be hinged to the main frame with the help of suitably designed G.I. plated clamp and 25 NB G.I. pipes. Gusset plates have to be provided to give extra strength to foot rest. Foot rest is to made of high quality HDPE material. Suitably designed HDPE pads has to be provided at the bottom of moving frame. Seat and back rest provided has to be made of HDPE.. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe is to be close by GI / HDPE caps for user safety against entrapment.

Sit Up Board-Providing, designing and fixing of single sit -up station of size 1504 x 1133 x 624 mm fabricated with main post of 140 mm dia and 3.00 mm thick ,Yellow sleeve dia 159 mm thickness 8.0mm, Connecting pipe dia 33 mm thickness 3.0mm and rest of the pipes are 2.75 mm thick,having bottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover,all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De - rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 90 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat shall be made up of steel pipe 2.75mm thick , with rounded edges to prevent any impact of injury and welded/ attached to main structure for vandalism proof design and long life. All open ends of pipe to be closed by Steel/ LLDPE caps for user safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J -bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover. 8 Exercising Bar:

The main frame of SKY MAchine is to be made in two parts, one from 80NB & 40NB Galvanized pipe & vertical pipe with 80NB pipe structure. The handle pipe is to be of 25NB GI pipes with PVC/rubber grip on top end. This handle pipes is to be hinged over 80NB main frame with the help of suitably designed heavy duty bearings assembly. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. The handle pipe is to be further extended to the rectangular tube of 50 x 50 mm on both sides with 40NB galvanized pipe links. Paired rectangular tubes with four foot rests has to be linked to main frame. Foot rest is to be made with the help of high quality Aluminium Casting material. The total structure is to be supported on Foundation stand which shall be of 80NB pipe. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be closed by GI / PVC caps for user safety against entrapment.

Horse Rider Station: Providing, designing and fixing of horse rider station of size 1000 x 600 x 1100 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Stair Stepper: Providing, designing and fixing of stair stepper in a combination of pair and a single step of size 1000 x 800 x 1400 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Pull Chair: Providing, designing and fixing of Pull pair of size 2500 X 800 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber at top end. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Seated Chest Press :- Providing, designing and fixing Seated Chest Press of Pull pair of size 1800 X 700 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Arm Wheel :- Providing, designing and fixing Arm Wheel in a pair of size 850 X 800 X 1800 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Elliptical Exerciser :- Providing, designing and fixing Elliptical Exerciser of size 1200 X 540 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Rowing Machine :- Providing, designing and fixing Rowing Machine of size 1280 X 800 X 1500 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Foothold shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The

Supply and fixing of Swings (5.83*4.0*6.66)- Plate form height above ground 2.0 to 2.5 m. The chain link should be plastic coated and take the load of80 kg.The Assy. Of swing has to be heavy duly ball bearing. With structural parts GI Pipes and MS Steel (including cutting,fitting, welding, bolting and smooth grinding etc.) complete.All the structural parts shall be polyester power coatedhaving minimum thickness of 50 micron.High quality fastened complete with supply/fixing andinstalled to be ground including civil work for making baseand pedestals.For safety of children sand bed with the minimum thicknessof 200 mm should be made in safe play by the vendor.

Supply and fixing of Straight Slide -Slider should be made of Mat. HDPE (Pipe) of ID 40 & OD 50 with nylon bush (mat finish) of demanded colour. With structural parts GI Pipes and MS steel (including cutting, fitting, welding, Bolting and smooth grinding etc. complete. All the structural parts shall be polyester powder coated having min. Thickness of 50 micron. High quality fastened complete with supply/fixing and installation to ground including civil work for making base and pedestals

Supply and fixing of See - Saw- Safe play area=1.0 to 1.5m*3.0 to 3.6m Sitting area should be coated with polyester fibre glass reinforced plastic (of 6 to 8 mm thickness). For structural parts GI Pipes and MS Steel (including cutting, fitting, welding, bolting, bearing and smooth grinding etc. ) complete. All the structural parts shall be polyester powder coated having min. Thickness of 50 micron. The structural parts should not to be painted, For structural parts stainless steel should be used. Nowhere Iron to be used Entire product is assembled with nut bolts, flanges and couplings. High quality fastened complete with supply/fixing and installed to be ground including civil work for making base and pedestals.

Maintenance of hardscape (paved area, pathway etc.), softscape and Plantation / Hoirticulture Works including Cleaning of all hardscape and softscape area, Maintenance of lawn/ herbs/ shrubs/ climbers etc.; Watering, weeding, cleaning, mulching, cutting etc.; Apply compost and organic fertilizers, Applying pesticides and insecticides; Disposal of dry and fallen leaves etc.; painting of kerb stone, mainteneance of all civil works electrical components. Total Cost for Operation & Maintenance for 60 months @ 0.25% per month to a total of 15% of the Total Cost

Installation of Open-Air Gym Equipment in Additional 74 Parks in Karnal

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc.as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer in charge)

Providing and Laying of plain Cement Concrete in Foundation of Kerb / levelling course including centering and shuttering but excluding reinforcement all complete as per drg. and MORT&H specifications sections 1500, 1700 and 2100 complete as per drawing and direction Engineer-in-charge.

Providing and applying two coats of synthetic enamel paint including primer to kerb surfaces etc. complete as per MORT&H Specifications clause 803 complete as per drawing and direction Engineer-in-charge.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per MORT&H Specifications Clause 401 (Grading–I of Table–400-1) and complete as per drawing and direction Engineer-in-charge.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) complete as per drawing and direction Engineer-in-charge.: 25mm Thick

Providing and fixing RCC Modern Park Bench complete as per standard, as per drawing and direction Engineer-in-charge.

Planting shurb including planting with manure, gardening and maintenance complete as per drawing and direction Engineer-in-charge. TABERNAEMONTANA DWARF

Planting shurb including planting with manure, gardening and maintenance complete as per drawing and direction Engineer-in-charge. CUPHEA HYSSOPIFOLIA

Planting shurb including planting with manure, gardening and maintenance complete as per drawing and direction Engineer-in-charge. DURANTA

Electrical Pole Led Light (5m Height) @20 C/C with Solar Panel A 24 watt solar street LED light as techinical specification and as per direction of Engineer-in-Charge

Manufacturing, supplying and fixing retro reflective sign boards made up of 2mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheetingconforming to type - XI of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2012, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriatepriming coat including all leads and lifts etc. complete as per drawing , MORT&H Specifications Clause 801 and direction of Engineer-in-charge. Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm

Air Walker -Providing, designing and fixing of Air Walker of size 992 x 505 x 1380 mm fabricated with mainpost of 140mm dia and 3.00 mm thickSwing leg is dia 48 mm thickness 2.75mm, Handle beam is dia 42 mmthickness 2.75mm , and other pipes of 2.75 mm thick having bottom plate 260 mm dia with thickness 12.00 mm ith ABS Cap/ Cover, all pipes made up of hot rolled ubular steel and pre galvanized, having Oil degreasingtreatment and Sand Blasting De -rusting treatment mustbe used before powder coating treatment with bakingtemperature of more than 200 degree Celsius using highquality paint Nippon or equivalent of 90 120 micronthickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Foothold shall be made up of steel 3.00 mm thick Nylon 4.00 mm thick, with rounded edges to prevent any impact of injury and welded/ attached to main structure for vandalism proof design and long life. Bearing No 6205 used shall be maintenance free, duly oil sealed and selflubricated made by reputed company. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by Steel/ LLDPE caps for ser safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J-bolts and when concrete is set, fixing the equipment on to it and cover nuts and boltswith base plate cover

Air Swing Providing and Fixing of AIR SWING Emphasizes on the front & back upper leg muscles exercise. Size1400× 915× 1360mm main post made of 4 inch pipe and other main pipes 1-1/2 inch pipes. 3mm thickness pipes Double coated P U Painting, heavy duty sealed ball bearing, for long lasting life. Rate including cost of all materials and labour charges including civil (foundation) works etc complete

Push Up AndDip Bar-Providing, designing and fixing of exercising bar in a pair of size 1802 x 612 x 1399 mm fabricated with main post of 140 mm dia and 3.00 mm thick and rest of the pipes 2.75 mm thickYellow sleeve is dia 159mm thickness 8.00 mm, Parallel Bar dia 42 mm 2.75mm, rest pipe is thickness 2.75mm, havingbottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover. all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De -rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 80 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J -bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover,

Waist Trainer-Providing, designing and fixing twister of size: 1365× 1708 x 1292 mm fabricated with main post of 140 mm dia and 3.00 mm thick and rest of the pipe 2.75mm, Yellow sleeve dia 159mm thickness 8.0mm,Handle beam is dia 33 thickness 2.75mm, Under plate pipe is dia 48 mm thickness 2.75mm, having bottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover , all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De-rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 90 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Foothold shall be made up of steel 4.00 mm thick , with rounded edges to prevent any impact of injury and welded/attached to main structure for vandalism proof design and long life. Bearing No 6205 used shall be maintenance free,duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by Steel/LLDPE caps for user safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630.The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M-25 with J-bolts and when concrete is set, fixing the equipment on to it and cover nuts and boltswith base plate cover,

The main frame of Leg Stretcher hall consist of 80 NB G.I. pipes with two suitably designed brackets attached on it. Brackets have to be made of M.S. material with G.I. plating. The moving frame of Leg Press is to be made of 40NB G.I. pipes which is to be mounted to the main frame with the help of suitably designed, machined shaft and bearing housing. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. Foot rest is to be hinged to the main frame with the help of suitably designed G.I. plated clamp and 25 NB G.I. pipes. Gusset plates have to be provided to give extra strength to foot rest. Foot rest is to made of high quality HDPE material. Suitably designed HDPE pads has to be provided at the bottom of moving frame. Seat and back rest provided has to be made of HDPE.. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe is to be close by GI / HDPE caps for user safety against entrapment.

Sit Up Board-Providing, designing and fixing of single sit -up station of size 1504 x 1133 x 624 mm fabricated with main post of 140 mm dia and 3.00 mm thick ,Yellow sleeve dia 159 mm thickness 8.0mm, Connecting pipe dia 33 mm thickness 3.0mm and rest of the pipes are 2.75 mm thick,having bottom plate 260 mm dia with thickness 12.00 mm with ABS Cap/ Cover,all pipes made up of hot rolled tubular steel and pre galvanized, having Oil degreasing treatment and Sand Blasting De - rusting treatment must be used before powder coating treatment with baking temperature of more than 200 degree Celsius using high quality paint Nippon or equivalent of 90 - 120 micron thickness. All joints of pipe should be cut by CNC laser cutting and robotic welded, with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Seat shall be made up of steel pipe 2.75mm thick , with rounded edges to prevent any impact of injury and welded/ attached to main structure for vandalism proof design and long life. All open ends of pipe to be closed by Steel/ LLDPE caps for user safety. The Equipment must confirm the Quality Standards Such as DIN 79000 and EN 16630. The equipment must have TUV certification in the manufacturing process. The equipment shall be fixed on ground with concrete of minimum strength M -25 with J -bolts and when concrete is set, fixing the equipment on to it and cover nuts and bolts with base plate cover. 8 Exercising Bar:

The main frame of SKY Machine is to be made in two parts, one from 80NB & 40NB Galvanized pipe & vertical pipe with 80NB pipe structure. The handle pipe is to be of 25NB GI pipes with PVC/rubber grip on top end. This handle pipes is to be hinged over 80NB main frame with the help of suitably designed heavy duty bearings assembly. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. The handle pipe is to be further extended to the rectangular tube of 50 x 50 mm on both sides with 40NB galvanized pipe links. Paired rectangular tubes with four foot rests has to be linked to main frame. Foot rest is to be made with the help of high quality Aluminium Casting material. The total structure is to be supported on Foundation stand which shall be of 80NB pipe. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be closed by GI / PVC caps for user safety against entrapment.

Horse Rider Station: Providing, designing and fixing of horse rider station of size 1000 x 600 x 1100 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Stair Stepper: Providing, designing and fixing of stair stepper in a combination of pair and a single step of size 1000 x 800 x 1400 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Pull Chair: Providing, designing and fixing of Pull pair of size 2500 X 800 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber at top end. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Seated Chest Press :- Providing, designing and fixing Seated Chest Press of Pull pair of size 1800 X 700 X 2000 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Arm Wheel :- Providing, designing and fixing Arm Wheel in a pair of size 850 X 800 X 1800 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Elliptical Exerciser :- Providing, designing and fixing Elliptical Exerciser of size 1200 X 540 X 1600 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc

Rowing Machine :- Providing, designing and fixing Rowing Machine of size 1280 X 800 X 1500 mm fabricated with main post of 140mm dia and 3.00 mm thick and other pipes of 40mm dia 3.00mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Foothold shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Engineer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The

Shivalik Constructions Company

M / S DAYANAND CONTRACTOR