REPAIR/ REPLACEMENT OF WATER TANK WITH STAGING AND CLEANING OF WATER TANK IN ZONE A AREA AND MAINTENANCE OF JOINERY, PLINTH PROTECTION, ROOF AND TILLING FOR CENTRALISED BUILDINGS UNDER AGE B/R-I AT BB CANTT, SRINAGAR

Amount

Dismantling wooden boarding, any description, fixed in any position with nails complete all as specified and as directed.

Dismantling timber scantlings 40 sqcm and over in section, in any position as in unframed/ framed work complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

M&L for clean sawn second class hard-wood in scantlings framed work complete all as specified and as directed.

S&F wooden fillets of 2nd class softwood, wrought square, rectangular or triangular in section of sectional area exc 13 sqcm and n.exc 25 sqcm fixed with nails etc complete all as specified and as directed.

S&F 6mm thick plywood, grade BWR, type BB, fixed with nails to timber frame work as in ceiling complete all as specified and as directed.

S&F 6mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with nails to timber frame work complete all as specified and as directed.

M&L for preparation of new or previously untreated wood and wood based surfaces and applying two coat of synthetic enamel paint over one coat of pink primer of any description not other wise described over 10 cm width or girth complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge thickness, including nanital or similar pattern roof covering complete all as specified and as directed.

S&F 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roof, wall etc with grade of zinc coating 275 complete all as specified and as directed.

S&F 0.80 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275, fixed with coach screws and washers, in roof, wall etc complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet (any pattern) 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified and directed.

M&L for brickwork with old size sub class 'B' bricks straight or curved on plan exc 6m mean radius and built in CM (1:6) etc complete all as specified and as directed.

Taking down cement plaster of any description, on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for 15 mm thick rendering in CM (1:6) on brick work or concrete surfaces, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

M&L for 5 mm thick rendering in CM (1:3) on ceiling surfaces, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

M&L for preparation of newly plastered or unplastered wall surfaces and applying two costs of cement base paint complete all as specified and as directed.

M&L for preparation of newly plastered or unplastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of primer complete all specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor & pavings n exc 15 cm thick below or above ground level complete all as specified and as directed.

M&L for 40 mm thick cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in floors, surface is to be finished even and smooth without using extra cement complete all as specified and as directed.

M&L for providing cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in cement concrete cills, steps, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removal to store 15mm bore pipe complete all as specified and as directed.

S&F Steel water tubing medium grade galvanised with all fitting complete to wall and ceiling or laid in floors of 15mm bore complete all as specified and as directed.

Ditto all as per serial item number 23.00 described here-in-before but 20 mm bore pipe.

Ditto all as per serial item number 24.00 described here-in-before but 20 mm bore pipe.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F rolled mild steel in compound girders & stanchions, lattice griders, aerial masts, staging for water tanks & the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates etc. of Gde Fe 410-W (Gde- E-250) Qty-B complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surfaces of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Dismantling water tanks of capacity exc 500 ltrs and not exc 1000 ltrs etc complete all as specified and as directed.

Ditto all as per serial item number 30.00 described here-in-before but capacity exc 250 ltrs and not exc 500 ltrs.

S&F 1000 litres capacity rotational moulded polye-thylene water storage tanks (cylindrical vertical with closed top) triple layered hoisted and fixed in position all as specified in SSR Part I including S&F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of size 20 mm dia complete all as specified and as directed.

Ditto all as per serial item number 32.00 described here-in-before but capacity 500 ltrs.

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of size 20 mm dia complete all as specified and as directed.

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of size 15 mm dia complete all as specified and as directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs cleaning etc and hoisting if required reconnecting and refixing in position after cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc complete (capacity of tanks exc 250 ltr and n exc 500 ltrs) including writing "date of cleaning" and next due date in bold capital letters Exc 4 cm in height complete all as specified and as directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs cleaning etc and hoisting if required reconnecting and refixing in position after cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc complete (capacity of tanks exc 500 ltr and n exc 1000 ltrs) including writing " date of cleaning " and next due date in bold capital letters Exc 4 cm in height complete all as specified and as directed.

S&F in repairs Fibre glass reinforced translucent 2mm thick corrugated or plain sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc. complete all as specified and as directed.

M&L for preparing new zinc (or galvanised) surfaces to receive painting, by coating with mordant solution including washing and cleaning, etc. complete all as specified and as directed.

S&F 25mm thick insulated PVC Wall Lining consisting of PVC Insulated Panels having expanded polystyrene (EPS) stuck to 2mm thick wood grain printed PVC sheet including suitable PVC beading duly fitted into the wall complete all as specified and as directed.

M&L for providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions including anodised aluminium snap grid frame work of size 605 x 605 mm for false ceiling and hangers 6 mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and as directed.

S&F in repairs for wooden laminated flooring in strips of size 120 cm long and 20 cm wide and 6-8 mm thick, fixed with PVC sheet and cushion including fillets/ cornices, laid over 12mm thick BWR plywood complete all as per manufracturer's instruction and all as specified and as directed.

S&F Khatamband pattern false ceiling, design as approved by GE with ornamental wood work made out of 1st class soft wood (Deodar) including hangers/ fillets/ cornices fixed over and including 12mm thick BWR plywood and finally finished with french polish (two or more coats) complete all as specified and as directed.

S&F 15mm thick 1st class soft wood Australlian wooden panelling fixed with toughened and grouted as wall panelling including fillets/ cornices fixed over and including 9mm thick plywood BWR fixing on walls and two coat of varnishing, polishing and preparation with sneezing complete all as specified and as directed.

S&F wooden fillets of 2nd class hard wood, plain clean sawn square, rectangular or triangular in section of sectional area exc 13 sqcm and n.exc 25 sqcm fixed with nails etc complete all as specified and as directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed.

M&L for 25 mm thick plain cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in sub base of floors finished even and fair complete all as specified and as directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile over and including 15 mm thick screed bed or bedding layer of mortar for laying floor finishes in cement mortar (1:6) complete all as specified and as directed.

M&L for Vitrified ceramic tiles (light shade) 10 mm thick (square/ rectangular) polished area of each tile not exc 0.36 sqm in floors set and jointed in neat cement slury and pointed in white or coloured to match the shade of tiles over and including 15 mm thick screed bed or bedding layer of mortar for laying floor finishes in cement mortar (1:6) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tile to store and rubbish off the premises complete all as specified and as directed.

M&L for Glazed ceramic coloured/ printed tiles 450X 350X 7mm thick as in vertical surfaces such as dado, skirting set jointed in neat cement slurry including pointed in white or coloured cement to match the shade of tiles over and including 10 mm thick backing coat in cement mortar (1:4) complete all as specified and as directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. Laid bedded in any mortar complete all as specified and as directed.

M&L for Granite (of any type) work, 20 mm thick, (table rubbed and polished) in steps jambs, pillars, window cills, cooking platforms, and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15 mm thick screed bed or bedding layer of mortar for laying floor finishes in cement mortar (1:3) complete all as specified and as directed.

S&F PBS roll 20 mtr long and 100 cm wide type-III weight not less than 40 Kg per roll (As per sample) complete all as specified and as directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frames) not exc 1.5 sqm each including cutting holes for taking out hold fasts or dismantling brick work/ stone work (holes cut and any other damage to jambs walls for taking out hold fast shall be finished identical to existing finish without any extra cost to the govt) complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F butt hinges, medium weight cold rolled, mild steel of size 75 mm complete all as specified and as directed.

S&F 100 mm long aluminium barrel tower bolts of extruded section complete all as specified and as directed.

S&F 100 mm aluminum alloy handles, fabricated type, anodised complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads including S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares n.exc 0.50 sqm in each pane complete all as specified and as directed.

S&F 6.30 mm thick sheet glass ordinary quality and glazing with oil puitty in squares exc 0.5 sqm each pane complete all as specified and as directed.

S&F Mortice lock, vertical type, size 100 mm Mild steel 2 levers complete all as specified and as directed.

S&F 150mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

M&L for 10 mm thick rendering in CM (1:4) on brick work or concrete surfaces, rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all specified and as directed.

S&F in repair aluminium clip (minimum size 18x18mm) with rubber gasket of suitable size and thickness as required at site for fixing glass in aluminium door/ windows complete all specified and as directed.

Taking down eaves gutters and rainwater pipes fixed to wall or laid in floors (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc. complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F in repairs wall mounted EWC with all fittings and accessories all as per manufacturers instruction, complete all specified and as directed .

S&F in repairs EWC cascade type with all fittings and accessories all as per manufactures instructions, complete all as specified and as directed.

S&F in repairs urinal with sensor, flat back with integrated EFS of size 740 x 330 x 362 mm, ivory with grating and union for discharge pipe includuing connecting to waste pipe, complete all as specified and as directed.

S&F in repair Vitreous china wash down water closet white orissa pattern of size 550 x 440mm including integral foot rest and PVC P or S trap (excluding flushing cistern and flush pipe) complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan with fixing bolts, trap (pedestal pattern), white, (excluding flushing cistern and flush pipe) complete all as specified and as directed.

S&F in repair wash hand basin vitreous china size 550 x 400mm white flat back including 15 mm bore CP pillar tap heavy duty as approved by GE, waste, chain plug, pvc connection, pvc waste pipe complete all as specified and as directed.

S&F in repair 15 mm bore CP Mixer single lever basin mixer fancy type for WHB / Sink with double action for hot/ Cold water complete all as specified and as directed.

S&F in repair PVC connection of PTMT nuts 15x600mm long complete all as specified and as directed.

S&F in repair PVC connection of PTMT nuts 15x450mm long complete all as specified and as directed.

S&F in repair 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flushing pipe complete all as specified and as directed.

Taking down aluminum windows including frame if required and repair the same including repair of rubber beadding, aluminum clip, adjusment of glasses, repair of floor spring or hydraulic door closer with oiling or greesing etc. adjusment of horizontal, vertical or middle style, complete all as till the satisfaction of Engr-in-charge.

S&F in repair waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange including waste pipe end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as specified and as directed.

M/S SHIMAR STAR GLACIER

M/S Tajamul Ah Buchh

M/S NORTHERN ELECTRICAL WORKS

M/S ATTAR BUILDERS

M/S BASHIR AHMAD MIR

M/S Vivek Gupta and Co

Alishan Builders

M/S DFA Enterprises

M/S SUHEEL CONSTRUCTIONS

M/S MOHAMAD YOUSUF AKHOON AND SONS