SPECIAL REPAIRS TO SEWAGE LINE, DRAIN, PROVN OF TOILETS, SINK AND KITCHEN RACKS

Amount

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep in soft/ loose soil for foundation, wells, manholes etc not exc 10 Sqm on plan getting out complete all as specified and directed.

Excavating over areas, not exc 1.5m deep & getting out in soft / loose soil complete all as specified and directed

M&L for approved earth filling with approved soil brought from out side MD land, filling in trenches or paving laid in layers not exceeding 25 cm thick spread, levelled and rammed including watering complete all as specified and directed

M&L for broken stone or boulders hard core of gauge n.exc 63mm deposited spread and levelled in layers not exc 15cm thick watered and rammed to a true surface complete all as specified and directed

Removing excavated soil exc. 50m but not exc 100m & depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and directed

M&L for PCC 1:4:8, type D-2 (using 40mm graded stone aggregates) mass concrete as in foundation filling and mass concrete complete all as specified and directed

M&L for 25 mm thick PCC 1:2:4, type B0 (using 12.5 mm graded stone aggregate) as in sub base of floor to receive tiles or Kota stone complete all as specified and directed

M&L for RCC M-25 design mix (using 20mm graded stone aggregates) as in footings and plinth beams complete all as specified and directed

M&L for RCC M-25 design mix (using 20mm graded stone aggregates) as in columns complete all as specified and directed

M&L for RCC M-25 design mix (using 20mm graded stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed

M&L for RCC M-25 design mix (using 20 mm graded stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed

M&L for mild steel "TMT" bars 10mm dia and over in reinforcement, cut to length, bent to shape required including crnaking, bending sprially for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed

M&L for mild steel TMT bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed

M&L for form work as use and waste to sides & soffits of plinth beam and sides of footings getting rough finished surfaces of concrete complete all as specified and directed

M&L for form work as use and waste to sides of columns getting rough finished surfaces of concrete complete all as specified and directed

M&L for formwork as use and waste to sides & soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors & beams, etc. fair finished surfaces of concrete flat complete all as specified and directed

M&L for formwork as use and waste to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; n exc. 200m thick (Horizontal or sloping) Fair finished surfaces of concrete flat complete all as specified and directed

M&L for brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed

M&L for brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed

M&L for rendering 5mm thick on fair faces of concrete surfaces in CM (1:3) in ceiling complete all as specified and directed

M&L for two coat cement plaster ,first coat 10mm thick CM 1:6 and second coat cement plaster 5mm thick in CM 1:4 with WPC finished even and smooth without using extra cement complete all as specified and directed. Note:-Water proofing compound shalll be paid seperately under respective item

Supply only integral waterproofing compound complete all as specified and directed

M&L for applying three coats of white wash on new wall surface including preparation of surface complete all as specified and directed

M&L for non skid ceramic coloured tiles 7 to 8mm mm thick (Square/ rectrangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11sqm as in floors laid over and including 15 mm thick cement screed bed in CM 1:4. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for glazed ceramic tiles of size 600mmx300mmx7 mm thick,(joint free (rectified)) coloured, on vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed in white/ coloured cement to match laid over and including 15 mm thick rendering in CM 1:4 complete all as specified and directed

S&F GI tubing `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 15mm bore complete all as specified and directed

S&F GI tubing `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 20mm bore complete all as specified and directed

S&F CP bib taps 15 mm bore, cast copper alloy fancy type with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule fancy type complete all as specified and directed

S&F 15mm bore stop cock CP fancy type with butter fly handle, screwed down, high pressure for iron pipes or for unions (weight not less than 400gms) complete all as specified and directed

S&F stop valves/angle valve 15 mm bore fancy type, CP with long shank & cup (conncelaed type), cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed

S&F Ball PVC valves 20mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed

S&F CP Pillar taps 15 mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position, three layered wall construction of 1000 Ltrs Capacity complete all as specified and directed

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed

S&F PVC (SWR) pipe 110mm bore single socketed in any length with adhesive joints fixed to walls with and including mild steel clamps of suitable size complete all as specified and directed

S&F PVC (SWR) vent cowl 110mm dia complete all as specified and directed

S&F PVC (SWR) pipe 110mm bore single socketed, in any length with adhesive joints laid in trenches or in floors complete all as specified and directed

S&F PVC bends any radius 110mm dia provided with axcess door complete all as specified and directed

S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm dia complete all as specified and directed

M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement complete all as specified and directed

S&F soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed

S&F CP fancy type Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed

S&F vitreous China bowl urinal angle back of size 430mm x 370mm x 340m mm white (min.), with grating & union for discharge pipe including waste pipe (excluding flushing cistern, flush pipe ) complete all as specified and directed

S&F vitreous China wash basin, white, flat back, size 550mmx400mm including 32 mm brass waste coupling,waste pipe and brackets complete all as specified and directed

S&F vitreous China squatting pan, 'Orissa' pattern, size 580mm x 440mm white, with integral foot rests incl flush pipe, provn of lime concrete bedding complete all as specified and directed

S&F vitreous China wash down water closet pan (pedastal pattern), white including white seat cover complete all as specified and directed

S&F PVC valveless, syphonic action type, flushing cistern (dual 5/10ltr capacity), low level, white, with intel, ball valve, float , handle and flush pipe 32mm bore and brackets complete all as specified and directed

M&L for cutting chases, pinning in, in brick/ stone wall making good to facings where required and pointing in cement mortar 1:3 or P. C. C 1:2:4 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring insert sheet in wall. etc. and making good, cutting not exceeding 10cm girth complete all as specified and directed.

S&F factory made Solid PVC prelam door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet single side prelam PVC sheet wood grain printed used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube complete all as specified and directed

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6mm raised panel design with 4mm thick moulded PVC sheet prelam on the front face & 4mm prelam PVC sheet on back face, supplying & fixing in frame centre core will be PVC battern complete all as specified and directed

S&F aluminium anodised barrel tower bolts of extruded section, length of bolt in 150 mm complete all as specified and directed

S&F Aluminium handles 150mm size, cast type, anodised complete all as specified and directed

S&F Butt hinges of 100 mm size, Medium weight, stainless steel and fixed complete all as specified and directed

S&F fixed type ventilators aluminium powder coated of frame size 50.80X 25.40mm,1.5 mm thick half portion will be fixed with 4mm thick frusted glass and half portion will be fixed with louvers with 4mm thick frusted glass with rubber gasket and aluminium beading ,aluminium grill with fixing arrangement (wt. of grill not less then 2.50 kg/sqm),aluminium wire mess 0.45 mm dia to be fixed over louvers portion only including necessary cutting holes on wall and fixing arrangements complete all as directed by Engr-in- Charge (Al. section thickness 1.50 mm }

M&L for precast reinforced cement concrete 1:1.5:3 type A-1 (using 20mm graded stone aggregates) as in cover slab of manhole set in cement mortar 1:4 complete all as specified and directed

M&L PCC in surface channels and drains type B0, 1:2:4 (using 12.5 mm graded stone aggregates) complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate laid in panels incl finished even and smooth with using extra cement as in plinth protection incl necessary form work to edges and filling of joints with bituminous sealing compound complete all as specified and directed

M&L for PCC (1:3:6) type C1 using 20mm graded stone aggregate as in coping and the like including weathering , slightly rounded or chamfered angle with and incl necessary use and waste of form work complete all as specified and directed.

M&L for applying three coats of white wash on new Ceiling surface including preparation of surface complete all as specified and directed

Demolition of brick work or rubbled stone masonry including all qoins arches , pillars etc built in cement mortar complete all as specified and directed

Demolition of RCC in precast cover slab any thicknes (reinforced) complete all as specified and directed

Demolition of cement concrete in ground floors and pavings not exc 15cm below or above ground floor complete all as specified and directed

M&L for walling of random rubble, brought up to course well bounded bedded and solidly hearted built in CM (1:4) complete all as specified and directed

M&L for rendering 15mm thick in CM (1:4) on Random Rubble stone masonry complete all as specified and directed

M&L for PCC 1:2:4, type B0 (using 12.5mm graded stone aggregates) as in benching of drain complete all as specified and directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms moulds, mitered /stopped ends complete all as specified and directed

Add or deduct for each 25mm girth or part there of over or under 30 cm complete all as specified and directed

Demolition & breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in CM of 300 boref pipe complete all as specified and directed

M&L for Reinforced concrete pipes 300 mm dia, class NP2, laid & jointed complete with Socket and spigot joints complete all as specified and directed

S&F in repairs PVC (SWR) pipes 110mm bore single socketed, in any length fixed in masonry drain for weep holes complete all as specified and directed

Taking down old existing PVC(SWR) pipes of 110mm/90mm bore complete all as specified and directed

S&F 75mm bore PVC(SWR) pipes single soketed in any length with adhesive jointed fixed to wall with mild steel clamps of suitable size complete all as specified and directed.

S&F PVC (SWR) bends 110 mm dia complete all as specified and directed.

S&F PVC (SWR) bends 75 mm dia complete all as specified and directed.

S&F PVC (SWR) junction single ( single T ) equal or unequal 110mm dia complete all as specified and directed.

S&F PVC (SWR) junction single ( single T ) equal or unequal 75mm dia complete all as specified and directed.

S&F 75 mm dia PVC ( SWR) floor trap with grating including jointing with solvant etc. complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm dia complete all as specified and directed.

M&L for PCC 1:2:4 type B0 (using 12.5 mm gradedstone aggregates) as in coping and the like including weathering, slightly rounded or chamfered angles and throating including form work complete all as specified and directed.

M&L for rendering 15mm thick cement plaster in cement mortar 1:4 on brick work finishing the surfaces even and smooth with out using extra cement complete all as per specified and directed.

Returning ,filling in including spreading ,levelling watering and well ramming with soil in layers n exc 25 cm thick complete all as specified and directed.

S&F in repair HDPE double wall corrugated sewage pipe of 100 mm internal bore, SN-8, ISI marked as per IS 16908 Part-II-2013 laid in trenches, jointed and tested as per manufacturer instruction complete all as specifed and directed. Make:Gemini-Tirupati Plastimatics Pvt Ltd, Jaipur (Raj)/ Keshav Kripa Polyplast (LLP), Kishangarh (Raj)/ Supreme Ultra Plus, Mumbai

All as per Srl item No. 86 above but 150mm bore

M & L concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D2 (using 40mm graged stone aggregtaes) for 100mm mm dia pipe work in foul position complete all as specified & directed.

M & L concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D2 (using 40mm graged stone aggregtaes) for 150mm mm dia pipe work in foul position complete all as specified & directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required of anty dia complete all as specified & directed.

M&L for soakage well excavation in any type of soil, foundation PCC 1:3:6 wells of honey combed and solid in M-25 concrete, including intercepting chamber screen chamber brick work in CM RCC cover slab in M-25 filling with brick bat complete of size 3.00 mtr dia and 3.00 mtr deep complete all as shown on Drgs, specified and directed.

Taking down 15 mm dia GI tubing and connection and refixing old 15mm GI tubing and connection in new or old position ( wall, floor, wall etc ) complete all as specified and directed

Taking down 20 mm dia GI tubing and connection and refixing old 20mm GI tubing and connection in new or old position ( wall, floor, wall etc ) complete all as specified and directed

Cutting existing steel tubing for alterations or additions (Each cut measured) 15 /20 mm pipe complete all as specified and directed

Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) 15 /20 mm pipe complete all as specified and directed

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 610mmx460mmx254 complete all as specified and directed.

S&F Stainless steel kitchen plate rack of size 31" X 36" X 10" fixed with screws complete all as specified and directed.

Cutting holes in brick walls in cement mortar or cement lime mortar and stone wall built in lime mortar for inserting holdfasts in exc. One brick but not exc. two brick wall and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required Cutting

S&F C P bib taps long body, cast copper alloy fancy conceled type with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule of 15 mm boreand fixed complete all as specified and directed.

Dismantling of floor, hearth or wall tiles / terrazo including cement mortar bedding (but not backing),removal servicable tiles and rubbish off the premises, all as specified and directed.

M&L for glazed ceramic tiles of size 450mmx 300mm x 7mm thick,(joint free (rectified)) coloured, on vertical surfaces such as skirting/dado set and jointed in neat cement slurry and pointed in white/ coloured cement to match over and including 15 mm thick rendering in CM 1:4 complete all as specified and directed

M&L for concealed point wiring for the following with 1.5 Sqmm PVC-FRLSH insulated, sheathed, copper conductor, stranded 1100 volt grade cable in & incl PVC conduit, including modular metal flush boxes & modular white cover plate with frame as per site requirement all fittings such as tees, bends, elbows, etc. of External diameter 20mm all as per site requirements PVC insulated & sheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead ,including cutting and chasing any type of wall complete all as specified and directed:-

One light, fan point controlled by one switch

One 3 pin ,5 Amp socket point with other switch on the same board

S&F Modular switch, one way, 6 Amp 230, 1 module complete all as specified and directed

S&F socket Modular 6 Amp-2/3 pin combined 2 module complete all as specified and directed

S&F ceiling rose, surface backlit,three terminal complete all as specified and directed

S&F Modular lamp holder insulated with back plate suitable for Angle/Batten fitting complete all as specified and directed

S&F MCB SP 6 Amp to 40 Amp 240 Volt 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed

All as per Srl item No.107 above but SPN 40 Amps, 240 V

S&F sheet metal enclosure for DB double door, IP-43 when MCBs to be used SPN, 4 way, 240 V with 200 Amps rated bus bar complete all as specified and directed .Note :- Cutting and chasing in stone masonary and making good to disturbed surfaces shall be deemed to be included in the quoted rate

S&F LED TL fitting 20/18 watt for surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver long life corresion resistance impact proof surface mounting IP66 Lumanires PC housing in opeal finish coverwith high brighness complete all as specified and directed .

S&F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 250MM complete all as specified and directed

Supply and laying cable XLPE insulated armoured heavy duty electric cable with aluminium conductor, 1100 volt grade cross sectional area 16 sqmm 2 core complete all as specified and directed

M&L for sand cushioning in trenches for the cable complete all as specified and directed

Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm complete all as specified and directed

S&F in replacement of GI Pipe light grade 50 mm dia ISI marked on pole on wall or laid in trenches incl all fittings (nut, bolt, clamps & washers) complete all as specified and directed

M&L for the GI tubing of size 25 mm bore, medium grade, ISI marked with all GI fittings (medium grade) incl laid in trenches , floor etc complete all as specified and directed .

S&F the Gun metal Gate valve iron wheel head both end screwed of size 25 mm bore for iron pipe complete all as specified and directed .

Cutting existing GI tubing for alterations ,screwing existing tube size of 40 mm and 50 mm dia for new connection including earth work and clamp, neccessory fitting as per site requirement complete all as specified and directed .

M K Construction