Certain repair to Plastering, Flooring, Joinery and Sanitary fitting in Offr, JCO, OR accn at Mil Stn Suranussi under AGE (I) Suranussi

Amount

Demolition of brick work built in cement mortar including all quoins arches etc all as specified and directed.

Demolition of cement conc in ground floor and pavings not exceeding 15 cm thick above or below ground level all as specified and directed.

Taking down cement or cement lime plaster incl raking out joints hacking for keys srubbing down with water etc all as specified and directed.

Taking down chowkats or frames with Shutters ( without taking off the shutter from the frame ) of area n.exc 1.50 Sqm each and removing from site all as specified and directed.

All as per Item No 4 above but area exc 1.50 Sqm but n.exc 4.00 Sqm all as specified and directed all as specified and directed.

Taking shutter only of any desription of size n. exc 1 sqm all as specified and directed.

Taking shutter only of any desription of size exc 1 sqm and n.exc 2sqm all as specified and directed.

Ditto all as per item No above but refixing in the same opening all as specified and directed.

M&L brick work , with sub class 'B' bricks built in cement mortar 1:6 straight or curved on plan exc 6mtr mean radious all as specified and directed.

Ditto all as per item No above but except bricks only complete all as specified and directed.

M&L 15mm thick cement plastering in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick cement plastering in cement mortar (1:4) on fair faces of brick work or concrete surfaces with using water proofing compound finished even & smooth without using extra cement complete all as specified.

M&l for 5 mm thick rendering in cement mortar in 1:3 on ceiling

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering to Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to GdeFe 290(Gde E-165)

M&L for 35 mm thick IInd class HW , factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

M&L for 35mm thick IInd class HW glazed /gauged shutters open rebatd and prepared to receive glass /gauge etc without sashbars edges of framing plain or chamfered or rounded fitted with cut and mitred beads for securing glass/gauge etc all as specified in SSR Part I section 8 clause 8.24 (a)

S&F 35 mm thick flush shutter solid core construction with block board core and plywood face panels commercial face on both faces complete all as specified and as directed

S&F solid PVC door frame of sie 50mmX 47mm made out of 5mm th plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing

S&F 30mm th Factory made solid panel PVC door shutter consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

Supply & Fixing for steel windows 1.25 mm thick box type (primer coated) ERW hollow 'P' section of size 60mm x 25mm single rebate comprises of skeleton shutter ERW sec 50 x 20 mm & 1mm thick and openable leaf consisting two nos sash bar of T section 20x3mm complete welded to frame including cutting holes and making good dismanteled portion in cement concrete (1:2:4) type B-I four nos for each window including following fitting welded to shutter complete all as specified and as directed by Engineer-in-Charge (i) Hold fast 150mm long 12 mm x 3mm made to shape - 04 Nos each window. (ii) Handle of Z Section 20 x 25 mm, 100mm long 01 Nos each leaf. (iii) MS tower bolt 150 mm long-02 Nos each leaf. (iv) Z Section 20 x 25mm, 100 mm stopper - 01 Nos per leaf (v) Cleat 55 mm long of hollow square 15x20x63mm welded to hinges - 01 Nos per leaf. (vi) MS Box type hinges of size 75 X 12 mm - 02 Nos per leaf. (vii) MS Guard bars square 12mm dia @10 cm c/c with GI frame fixed to window frame. (viii) Fabrication and fixing Note :- Glass shall be measured and paid for separately.

Ditto all as above ser item No 20 here in before but skeleton shutter to recieving wire mesh as directed by Engineer-in-Charge

S&F 300mm size mild steel sliding door bolt plate type stove enamelled black with bright bolt not less than 12mm dia incl a minimum of six nut and bolts ,four on bolt plate and two on stapple plate complete all as specified

S&F mild steel barrel tower bolt 200mm size stove enamelled black with bright bolt etc all as specified

S&F 150 mm size mild steel pressed handle oval t ype stove enamelled black all as specified and directed.

S&F 100 mm size mild steel butt hinges medium weight all as specified and directed.

S&F floor door stopper aluminiumalloy body and tounge 140mm anodised with hard drawn steel spring etc all as specified and directed.

S&F 300mm size mild steel rat rail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F in repair block board 19mm thick commercial type exterior grade fixed to timber frame work all as specified and directed.

S&F in repair pre laminated decorative block board 25mm th prelminated on one face etc fixed to timber frame work all as specified and directed.

S&F galvanized mild steel wire cloth 0.56mm dia of wire and average width of aperture 1.18mmall as specified and directed.

Ditto all as per item No 30 above but fixed in repair all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones, S & F 3 mm thick glass sheet ordinary quality glazing with oil putty in square n.exc 0 .5sqm in each pane all as specified and directed.

S & F 3 mm thick glass sheet ordinary quality glazing with oil putty in square n.exc 0 .5sqm in each pane all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises all as specified and directed.

M&L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over15 mm th screed or bedding layer in CM 1:6.complete all as specified and directed by Engineer-in Charge.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchwith surrounding cement, over15 mm th screed or bedding layer in CM 1:6 , dismantling tiling cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises all as specified and directed.

M&L Non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over15 mm th screed or bedding layer in CM 1:6.complete all as specified and directed by Engineer-in Charge.

M&L for glazed ceramic tiles coloured of size 450 mm x 350 mm x 7mm th on vertical surfaces such as in skirting, dado etc over 10 mm th backing coat in cm 1:4 complete all as specified and directed by Engineer-in Charge.

S&F in repairs vitreous china water closet Padestal pattern( white ) includng trap but excluding fixing bolts, flushing cistern and flush pipe complete all as directed.

S&F in repair vitreous china squatting pan ‘Orissa patten’ size 580x440mm white with intergral foot rest (excluding flushing cistern and flush pipe) with "P' or "S" trap including water connection to trap and flushing pipe, flushing cistern etc incl lime concrete bedding and PCC 1:2:4 for making good the floor fixed in repair complete all as specified and directed

S & F in repair PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore, connection to WC pan & PVC connection 15mm size with PTMT nuts of length 300mm complete all as specified .

S& F in repair vitrious china wash hand basin flat back 550X400mm incl fixing bracket, pvc waste coupling and waste pipe,cp pillar tap etc all as specified and directed by engineer-in-charge .

S&F in replacement 20 mm dia harrison rails mild steel with decorative finish , with fixing brackets , stops, rollers complete all as specified and as directed

Dismantling water tanks of any description exc 250 and n.exc 500 ltr capacity all as specified and directed.

S&F Rotational moulded polythene water storage tanks double layer (cylinder each vertical with closed top) of capacity 500 Itrs, hoisted and fixed in position including pvc float valve 20mm size,specified in SSR Pt-1 all as specified and directed. Make :- Sintex / Frontier / Polycon

Taking up/ down GI tubing and connections with all fittings 15 mm bore all as specified and directed.

Ditto all as per item No 47 above but 20mm bore all as specified and directed.

S&F 15 mmdia GI tubing and connections fixed to wall or ceiling, laid in floor etc all as specified and directed.

ditto all as per item No 49 above but fixing only all as specified and directed.

S&F 20 mmdia GI tubing and connections fixed to wall or ceiling, laid in floor etc all as specified and directed.

ditto all as per item No 51 above but fixing only all as specified and directed.

S&F in repair CP shower rose 15mm sizefixed to iron pipe all as specified and directed.

S&F pvc connection 15mm size with PTMT nuts of length 450mm all as specified and directed.

S&F in repair 15mm CP Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and directed.

S&F in repair 15mm size brass stop valves with crutch or butterfly handles high pressure screwed both ends for iron pipe all as specified and directed.

Ditto all as per item No 56 above but fancy type, chromium plated with long shank and cup (concealed type) all as specified and directed.

S&F in repair 20mm size stop valves PTMT high pressure screwed for iron pipe all as specified and directed.

S&F waste coupling of PTMT 32 mm dia half or full threaded for WHB all as specified and directed.

S&F waste coupling of PTMT 40 mm dia half or full threaded for Kitchen Sink all as specified and directed.

S&F in repair 15 mm bore brass CP WHB mixer for hot and cold water screwed down for iron pipe etc complete all as specified and as directed by engineer-in-charge .

S&F in repair towel rail 600mm long of PTMT incl cp brass srews etcall as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided all as specified and directed.

M&L preparing new surfaces of walls and applying two coats of oil bound distemper over a coat of alkali primer etc all as specified

M&L preparing surfaces of new walls and applying two caots of cement base paint over and a coat of alkali primer all as specified and directed.

M&L for three coats of white wash on on ceiling on newly plastered surfaces all as specified and directed.

M&L for two coats synthetic enamel paint on new wooden surface over 10 cm width or girth over a coat pink primer all as specified and directed.

M&L for two coats of synthetic enamel paint on new steel surface over 10cm width or girth over a coat red oxide primerv etc all as specified

M&L PCC 25mm thick 1:2:4 type B-0 using 12.5 mm graded stone agg as in levelling course all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 as in plinth protection with using 40mm graded stone aggregate etc all as specified.

S&F in repair PVC SWR pipe 110 mm dia single socketed in any length with rubber ring joints fixed to walls etc all as specified

Ditto all as per item No 71 above but laid in trenches all as specified and directed.

S&F in repair PVC SWR pipe 75 mm dia single socketed in any length with rubber ring joints fixed to walls etc all as specified

Ditto all as per item No 73 above but laid in trenches

S&F in repair 75mm size PVC (SWR) floor trap plain with grating incl to jointing with waste pipe with adhessive etc all as specified

S&F 110 mm dia PVC SWR type bends any radius complete all as specified

Ditto all as per item No 76 above but 75mm dia etc all as specified

S&f 100 mm dia stack clamp made out of 25x4mm Flat iron etc all as specified

S&f 75mm dia stack clamp made out of 25x4mm Flat iron etc all as specified

Form work to soffits of suspended slab such as roof slab/Kitchen slab n exc 200mm thick (horizontal/sloping/vertical) with fair finished surface complete all as specified

M & L TMT bars 6mm to 8mm dia. cut to length bent to shape required including cranking, bending and binding with and including ms wire (annealed) n. less than 0.9mm dia or securing with clips complete all as specified

Demolition of cement concrete is reinforced of any description and in any position not otherwise specifically provided all as specified and directed.

M&L Reinforced cement concrete (nominal mix) Type B-0 1:2:4 (12.5mm graded aggregate) in slabs supported on walls, beams, columns deck slabs and in shelves, the like all as specified and directed by Engineer-in-Charge

M & L Reinforced cement concrete (nominal mix) Type B-0 1:2:4 (12.5mm graded aggregate) in Chajjas all as specified and directed by Engineer-in-Charge

Supply & fixed sliding/opening anodised aluminum door/window shutters including frame,and made out of hollow extruded alumimum sections as mentioned below. Each door having 02 Nos D type handles, 02 Nos aluminium tower bolts 300 mm size,01 Nos of lock, hydraulic door spring. Shutter to be partly glazed with 5mm thick, plain or tinted glass and partly paneled with 12 mm thick prelaminated particle board fixed with glazing clips, rubber beading / gasket, anodized aluminum beading, screws including bothside openable in door bottom hydraulic double action machine machine complete all as per specified and directed. Chowkat / frame 101.60 x 44.45 x 1.60 mm thick Shutter top and bottom rail : 114.30 x 44.45 x 1.55 mm thick, Shutter middle rail 83.50 x 44.45 x 1.55mm, Shutter verticle style : 85 x 44.45 x 1.55 mm thick.complete all as specified

AAY KAY Constructions

SUNRISE CONSTRUCTION COMPANY

SONA BUILDERS