UPGRADATION OF SOLAR PANEL ON EXISTING SUBMERSIBLE AT ICDS CENTRE AT NALIAPUR UNDER SITAHATI GRAM PANCHAYAT (Scheme id- 127955257 )

Solar Module: Supply , transport , installation and commissioning of ISI marked Solar Modules as per following specification: 1. Cell: Indigenous mono crystalline silicon SPV cells 2. Solar Module: Monocrystalline cell with PERC technology / module with bifacial cell. 3. Standards: ISI marked as per IS 14286 and having certification of IEC 61853(1), 61730(1&2), 61710 4.Modules must qualify to IS 170210 (Part 1) 5.Min. Efficiency: 19.5%. 6. Fill factor: More than 75% . 7. Module wattage mismatch in the SPV array: within ±3% 8. Wattage output warranty:Should not be less than 90% at the end of 10 years and 80% at the end of 25 years. 9.The power output of individual PV modules used in the PV array, under STC: minimum 300 Wp. Necessary test certificates also to be supplied. For detail information please see Cl. no. 2.1 of technical specification. a) For 1 HP Off-grid Solar Water Pumping System with Monocrystalline/ Monocrystalline PERC/bifacial SPV modules - 900 - 1200 Wp. (Solar Submerssible pump)

Power conditioning unit with enclosure :Supply , transport , installation and commissioning of Solar Power conditioningUnit consisting of following components and features: 1) Variable frequency Drive with inbuilt MPPT, voltage rangesuitable for operating pump-motor set of 1HP to 20 HP, detail mentioned in Cl.6.12) Power input : DC source for 1HP, 2HP and 3HP.3) Power input : AC / DC source or hybrid for 5HP and above.4) Incomer: DC MCB 2 Pole 16 amp upto 5 HP, 25 amp for 7.5HP and 10 HP, 40 ampfor 15 to 20 HP as per IS/IEC 60947-25) Incomer: AC MCB 4 pole 16 amp for 5.0 HP, 25 amp for 7.5HP and 10 HP, 40 ampfor 15 to 20 HP as per IS/IEC 60947-2 6) Type II DC SPD of 40 KA. 7) Type II AC SPD of 40 KA for AC/ DC or Hybrid input. 8) Dual input (solar/Grid) 25 amp changeover switch for 5HP and 7.5 HP, 40 ampfor 10 HP, 63 amp for 15 to 20 HP 9) Reverse protection diode 1600 VDC with heat sink.10) Data Logger.11) Remote monitoring system.12) Should have built –in EMC filters .13)IP 65 glands for cable in and out. 14) Min. IP 54 enclosure.For detail features, protections, RMS, Communication architecture, Security, Data storage, tolerance of various parameters, standards to be qualified, etc. please refer to Cl. 6.1 of technical qualification. Note: AC SPD, AC MCB and Selector switch to be provided only for item no. 3(f) to 3(l). a) For 1 HP capacity Pump-motor set with AC / DC or hybrid input (For Solar Submerssible)

Cable and Accessories :Supplying, fitting and fixings of UV rated Copper Cable laid inside HDPE conduit andother accessories as per followings with necessary connection with the Solar PVModule, MPPT etc.i. 4.0 Sq mm single core multi studs - 5m(for 1HP/2HP/3HP) & 20m(for5/7.5/10/15/17.5/20 HP)ii. Lugs, HDPE Pipe, Flexible Pipe, Saddle, Cable tie etc a) For 1 HP/2 HP/3HP per structure (For Solar Submerssible)

Earthing: Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By ISI-Medium GI pipe including excavation of soil for installation of Earth Electrode and filling & ramming and connecting to individual structure to earth electrode including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc.

M.S. structural works in columns, beams etc. with simple rolled structural members …………………..including all incidental chages such as electricity charges, labour insurance charges etc. I) For structural members of specified sections weighing less than 22.5 Kg./m (For Solar Submerssible)

Supply and instalation of 80 mm bore well 1 HP Submesible pump (Kirloskar/ Crompton/ C.G/ K.S.B./CRI or other approved brand as per direction of EIC ( AC/ DC supply 80 to 110 Volt outlet 32 mm )

Power Conditioning Unit (PCU) Supply & installtion of Ongrid Hybrid PCU, 1 KV, 24V System, Main Features - PCU should be a combined unit comprising of inverter, charge controller, visual display and necessary protection. It should be industrial grade bi-directional Inverter It should have Integrated MPPT Charge Controller It should be rated for Continuous operation at full load It should have Programmable battery management parameters It should have solar priority grid charging & Load. It should Automatic restart after over load triggered shutdown. It should have Continuous battery life and state of health monitoring. PCU should have provision for PCU by-pass arrangement so as to cater load directly through grid, In case of PCU failure Major Specification are as follows: Rating of PCU-1 KVA 230 V AC sine wave inbuilt MPPT Charge Controller Suitable to charge (2 nos 12V 100 AH Battery Bank, Control Type-Voltage Source, Microprocessor assisted, Output regulation. Power Control MPPT, Output Voltage - 1 Phase, 230V AC, adjustable up to 250V (+12.5%, -20% V AC) Frequency-50 Hz, +-0.5 HZ, DC link Voltage range, Operting Temperature Range 0 C to 55 C. Housing Cabinet - PCU to be housed in suitable switch cabinet with protection Class - IP20. Over load capacity 200 % of continuous rating for 10 Sec. Over load Protection - Auto Reset Protections: Grid over/Under voltage, Grid Over/Under frequency, Inverter Over load, Unbalance Output load, Short Circuit (line-to-line & line-to-ground), Battery Low/High Shutdown. Solar/Battery Reverse, Surge Protection at AC and DC both side Front Panel Displaying : Battery Voltage & Current SPV Voltage, Current, Instantaneous Power (KW), Instantaneous Energy (kWh), Inverter Output Voltage, Current nad Power (kVA), Grid Voltage, Current, Battery Charging and Discharging status and Charge level Indicator Front Panel LED Indicators : System On, Inverter On, SPV Charging, Mains Charging, Battery Low, System Fault Dielectric Strength : 1.1 kV between input/output with ground with EMI protection & 1.5 kV between input and output Standerd & Make : As per MNRE Guidelines and conforms to IEC 61683 and IEC 60068

Display Board

Add GST @ 18% (It 1-8)

Add Cess @ 1% (It 1-9)